Construction of Degree College at Barkagaon in Hazaribagh District under Vinoba Bhave University, Hazaribagh

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classfication of soil item - A) and disposal of excavated earth a obtained to a distance up to 50M including all lifts with leveling ramming the foundation trenches removing roots of trees shurbs all complete as per approved design and per building specification and direction of E/I.

Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item - B)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I. (Mode measurement compacted Volume).

Extra for each subsequent lead upto 25M beyond the intial lead of 50M (Maximum upto 150M lead by head load) as per specification and direction of E/I.)

Providing coarse clean sand in filling in foundation trenches or in plinth including thick with all leads and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. (Mode of measurement compacted voume)

Providing designation 75b work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75Bbrick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints costs of screening materials, scaffolding, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding theb cost of reinforcement) all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

1:1½:3 (1 cement : 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases

Foundations, footings, bases of columns, etc. for mass concrete Weather shade, Chajjas, corbels etc., including edges

S/F 35mm thick solid core type non-decorative single leaf flush door and windows with black board core banded with high quality phenol formaldehydes synthetic resin both side commercial veneered of standard make with oxidized iron fittings such as hinges, sliding door bolts tower bolts, handles or rings hooks and eyes, cleats sand block as per schedule taxes and royalty all complete as per building and direction of E/I.

Supplying, fitting & fixing 35mm thick solid core type non-decorative double leaf flush shutter in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneeres of standard makew with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing plain M.S. reinforcement of 6mm dia roads as per approved design and drawing excluding carriage of M.S. roads (Straight or in coils) to work site, cutting, bending end binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.

Providing TMT steel reinforcement 8mm dia rods to 12mm dia as per approved design and drawing excluding carriage of M.S. roads (Straight or in coils) to work site, cutting, bending end binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.

S/F M.S. grill made of 20 x 6mm M.S. flat as per approved design and drawing, properly fabricated with joints continous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction ofE/I. (Where materials is not supplied by the deptt.)

Providing and fixing fan hook of 16mm dia TMT M.S. bar I meter long bent to required size and shape placed in position and fixed in RCC slab/beam at the time of casting all complete as per building specification and direction of E/I.

S/F local make collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat disgonal 30 x 3mm, with top and bottom rails of T iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts nuts locking arrangements steppers handles including applying a priming coat of red lead paint carriage hoisting and taxes all complete as per building specification and direction of E/I.

S/F local make fully glazed steel door, windows or ventilation of standard rolled 'Z' and mullion steel section and size as per IS - 38 joints met welded with 100 x 16 x 3mm M.S. lug fixed in cement concrete (1:2:4) blocks, 15 x 10 x 10cm size including cost of oxidized iron fitting with hinges, handle per step catch springs, 3mm thick plain glass panes with aluminum beads and inner frame fixed with lugs with 20mm long 6.3mm GI. counter sunk machine screw and nuts and applying a coat red lead paint carriage to work site hoisting and plcing in all position in all storys and taxes all complete as per building specification and direction of E/I.

Providing designation 75A one brick flat soiling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/I.

Drilling 6mm dia hole M.S. angle iron for fixing of staples etc. as per building specification and direction of E/I.

Labour for cutting of M.S. angle iron post to required length, one end splitted as fishtailed in a length of 150mm complete as per building specification and direction of E/I.

S/F 35mm dia G.I. pipe fitted and fixed in floor outlet to drain out water in cement concrete including cutting hole making good the wall and finishing, all complete as per building specification and direction of E/I.Down Slab of Toilet

S/F M.S grill gate with M.S. grills made of 20 x 6mm M.S. flats or 16mm M.S. square bars fitted on 25 x 25 x 6mm M.S. Angle frame - do - (when steel is not supplied by the deptt.)

Providing designation 75 A one brick flat joints filled with local sand including cost of watering taxes royality all complete as per building specification and direction of E/I.

Providing designation 75b one brick flat soiling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I

Providing designation 75B one brick on edge soiling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/I.

Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. (iv) 600X600 mm size

Providing and laying 15mm to 23mm thick kotah stone tiles in risers of step, skirting and pillars of approved size texture and colour laid over 12mm thick cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing to granolilthic finish with approved quality of carborandom stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Chequerred precast cement concrete tiles 22 mm thick in footpath &courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).Light shade pigment using white cement.

Fine Dressing of Ground as per instruction and specification of E/I

Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I.

Providing 12mm thick cement plaster (1:6) -with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I.

Providing 1.5mm cement punning including curing carriage of water with all leads and lifts as per building specification and direction of E/I.

Providing 19mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Prociding 25mm thick water proof cement (1:4) with clean coarse sand of F.M. 1.5 including screening curing with all leads lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Making 6 x 6mm grooves in plaster surface over walls truly horizontal or vertical as specified at regular intervals at all height including cleaning, finishing scaffolding and curing with all leads and lifts of water all complete as per building specification and direction of E/I.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastrered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt including scales, smokes, grease and sand preparing, including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specificatio).

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing 250mm wide brick drain in cement mortar (1:6) with as. 150mm clear depth and 250mm apron including cost of earthwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

providing 150mm wide brick draing in cement mortar (1:6) with av. 150mm and 125mm apron including stacking serviceable material within 15M lead and disposal of unserviceable material with all leads all complete as per direction of E/I.-

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20mm nominal size ) over 75mm bad by dry brick ballast 40mm nominal size well rammend and consolidated and grouted with fine sand including finishing the top smooth.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width aswell as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in charge.All kinds of soil

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement:3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over75mm thick bed of dry brick ballast 40 mm nominal size, well rammedand consolidated and grouted with fine sand, including finishing the topsmooth.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

80x1.25 mm M.S. laths with 1.25 mm thick top cover

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot DipGalvanised with serrations and serrated washers to arrest the wind loadmovement, fasteners, SS 316 Pins and anchor bolts of approved make inSS 316, Nylon separators to prevent bi-metallic contacts all completerequired to perform as per specification and drawing The item includescost of all material & labour component, the cost of all mock ups at site,cost of all samples of the individual components for testing in an approvedlaboratory, field tests on the assembled working curtain wall with aluminiumcomposite panel cladding, cleaning and protection of the curtain wall withaluminium composite panel cladding till the handing over of the building foroccupation. Base frame work for ACP cladding is payable under the relevantaluminium item.s The Contractor shall provide curtain wall with aluminiumcomposite panel cladding, having all the performance characteristics allcomplete , as per the Architectural drawings, as per item description, asspecified, as per the approved shop drawings and as directed by theEngineer-in-Charge. However, for the purpose of payment, only the actualarea on the external face of the curtain wall with Aluminum CompositePanel Cladding (including width of groove) shall be measuredin sqm. up to two decimal places.

Providing and fixing pressed steel door frames confirming to IS : 4351 manufactured from commercial mild steel sheet of 1.25mm thickness including hinges jamb, lock jamb bead and if required angle threshold of mild steel angle of section 50 x 25mm, or base ties of 1.25mm pressed mild steel welded or riidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after-treatment of the surface as directed by Engineer-in-Charge.

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, ailings, brackets, gates and similar works

Granular Sub-base with Close Graded Material (Table:- 400-1) By Mix in Place Method (Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401).for grading- I Material

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. Granite of any colour and shade

Providing and fixing concertina coil fencing with punched tapeconcertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height ofwall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied withG.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per directionof Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mmwith tape (0.52 mm thick) and weight 43.478 gm/ metre (cost ofM.S. angle, C.C. blocks shall be paid separately)

Angle Size.(ii) 65x65x6/8/10 (Gr.A)

Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-In?Charge

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood - 50 x 20 mm

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foamsheet, mitred at corners and joined with 2 Nos of 150 mm long bracketsof 15x15 mm M.S. square tube, the vertical door frame profiles to bereinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frameto be fixed to the wall using M.S. screws of 65/100 mm size, complete asper manufacturer’s specification and direction of Engineerin-Charge

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing. 30 mm thick pre laminated PVC door shutters

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike- plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer- in-charge: Profile C - Fixing with adjustable lugs with split end tail to each jamb

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use ofchequered plate wherever required, all complete

M.S. tube

Railing

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) 25mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado andpillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3coarse sand) and jointed with grey cement slurry mixed with pigment tomatch the shade of the slabs, including rubbing and polishing complete

Marble work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately) Area of slab over 0.50 sqm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conformingto IS : 15622 of approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4Coarse sand), including pointing the joints with white cement and matchingpigment etc, complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete

Providing and laying Double Charge vitrified floor tiles in Different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and confirming to IS 15622/ISO 13006, of approved make , in all colour and shades laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointed with grey cement [email protected] kg /sqm including grouting the joints with white cement and matching pigment etc.Size of tiles 600x600mm

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.Rate per cum for grading-I Material

Making Khurrah Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler - 110mm

Single tee with door - 75x75x75 mm

Single tee with door - 110x110x110 mm

Single tee without door - 75x75x75 mm

Single tee without door - 110x110x110 mm

Bend 87.5° - 75 mm bend

Bend 87.5° - 110 mm bend

Bend - 110mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete .Cllip 110mm

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm overand including priming coat of exterior primer applied @ 2.20kg/ 10 sqm)

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surfaceto prepare the surface even and smooth complete. sqm 89.65

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strongvibratory compaction, of approved size, design & shape, laid in requiredcolour and pattern over and including 50mm thick compacted bed of coarsesand, filling the joints with fine sand etc. all complete as perthe direction of Engineer-in-charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineerin- Charge.60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) - Powder coated aluminium (minimum thickness of powdercoating 50 micron)

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20 mm nominal size)

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.For the purpose of measurement the entire treated surface will be measured.

Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (40mm & above) x (40mm & above) & sash (25mm & above) x (50mm & above) with zinc alloy (zamak) powder coated touch locks with hook (Height upto 1.2 meter)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Providing and fixing 100mm brass locks (best make of approvedquality) for aluminium doors including necessary cutting and makinggood etc. complete.

Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer- in-charge.Powder coated minimum thickness 50 micron aluminium

Providing and laying water proofing treatment in sunken portion of W.C.'s, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying: a) First layer of slurry of cement @0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with curing for 48 hours. The rate includes preperation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry (Work should be Done by Registered Applicator of B.S.F., Sikka ,Fosrok,Pidilite With 10 year Gurantee.)

Water proofing for old and New Roof slab:- Providing and laying water proofing treatment on roof slab by applying two Component, factory………………E/I.

Covering of treated surface with PCC:- Providing 25mm thick Cement concrete M-20 (1:1.5:3) maintaing slope in alternate 2 Mtr. X 2Mtr. Panels with approved quality of stone chips of 20mm to 6mm Size graded and cleaned sand of F.M. 2.5 to 3 including screening................E/I.

Providing and filling of 6mm thick Groove between 25mm PCC panels with Polysuplhide sealant (Poring Grade) as per drawing and techinical speicifcation and direction of E/I.

Supply & Fixing shaliltex board( for use as expainsion joint I.S.1838-1938 filter )

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions.

The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063.)

Roof Joint of 150 mm gap

Carriage of materials

Bricks Lead = 1 k+7 P(8km)

Fly Ash Brick - 15km

Sand lead = 10 km

Stone chips lead = 22 km

Stone metal lead = 22 km

Local Sand lead = 3km

Supplying & stacking of good earth at site including coverage up to 1 Km.

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 75 A brick work in C.M. (1: 6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 125mm thick reinforced designation 75A brick work in (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement0 all complete as per building specification and direction of E/I.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :

With "A" grade whitE Tiles.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 500x500 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

110 mm diameter

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 500x500 mm

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Shoe - 110mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mmhard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm

Providing and applying plaster of paris putty of 2 mm thickness overplastered surface to prepare the surface even and smooth complete

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqmover and including priming coat of exterior primer applied@ 2.20 kg/10 sqm)

Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 16mm . L S

Spreading of sludge, dump manure and / or good earth in requiredthickness as per direction of Officer-in-charge (Cost of sludge, dumpmanure and / or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specifiedor directed by the Officer-in-charge..

Fine Dressing of Ground ….

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.

Providing & Fixing decorative high pressure laminated sheet of plain I wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge),minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/ kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

With float glass panes of 4.0 mm thickness

Stainless steel wire guage (Grade-304) aperture 1.4 mm and 0.50mm dia wire

Covering of treated surface with PCC :- Providing 50 mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :

First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete

Ridges plain (500 - 600mm)

Flashings/ Aprons.( Upto 600 mm)

Gutter (600 mm over all girth)

Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thickbottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with:8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in?charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing 150mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with:

Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area

Supplying fitting & fixing G.I. pipes (Tata make) or equivalent as per I.S. 1239 (part - I)/2004 ISI marked OR medium quality (65mm dia)

Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size GI box and earthing the point etc as required

Group A

Group B

Group C

Twin Control Point Wiring in PVC Conduit, with Modular type Switch: Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, 2 way modular type switch, modular plate, suitable size GI box and earthing the point with 1.5 sq mm. FR PVC insulated copper conductor single core cable etc as required

Power Plug Wiring in PVC conduit(2x4 sq. mm): Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit alongwith 1 number 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 Sqmm + 1x1.5 sqmm earth wire

2x2.5 Sqmm + 1x2.5 sqmm earth wire

2 X 4 sq. mm + 1 x 4 sq.mm Earth Wire (Sockets)

2 x 6.0 sq.mm. + 1 x 6.0 sq.mm. earth wire

2 x 10 sq.mm. + 1 x 10 sq.mm. earth wire

4x6 Sqmm + 2x6 sqmm earth wire

4x10Sqmm + 2x10sqmm earth wire

4 X 16 sq. mm + 2 x 6 sq.mm Earth Wire

Supplying and drawing following pair 0.5 sqmm FR PVC insulated copper conductor unarmored telephone cable in the existing surface/conduit

Supplying and fixing of following sizes of PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required for Tele, RJ45 Cat 6 data outlet for computer network.

S/F Modular type switch socket - Supplying and fixing following modular type switch/socket on the existing modular plate and switch box including connection but excluding modular plate etc. as required

5/6 amps, one way switch

5/6 amps, 3 pin socket outlet

Telephone socket outlet

TV antenna socket outlet

S/F Modular type electronic fan regulator: Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

S/F Modular type blanking plate :-Supplying and fixing modular blanking plate on the existing modular plate & switch box but excluding modular plate as required.

S/F Modular boxes, base & cover plate :-Supplying and fixing following size/ modules G.I. box along with modular base & cover plate for modular switches in recess etc as required.

1 or 2 module (78 mm x 78 mm x 45 mm)

4 module (78mm x 140mm x 50mm)

6 module (78mm x 205mm x 50mm)

8 module (78mm x 230mm x 60mm)

12 module (135mm x 205mm x 60mm)

S/F Light plug Point with Modular type accessories: Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc as required.

S/F Power plug Point with Modular type accessories: Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch connection, painting etc as required.

S/F Ceiling Rose: Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooen block including connection etc as required. Make :- Anchor / Kona / Kany

S/F Batten / Angle Holder: Supplying and fixing batten / angle holder including connection etc as required.

S/F Call bell buzzer - Supplying and fixing call bell/buzzer suitable for D.C./A.C. single phase, 230 volts, complete as required.

ITC fluorescent fitting directly on surface :-installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc, directly on ceiling / wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper cond.

ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq. mm. FRPVC insulated,copper conductor,single core cable etc, as required.

ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F rewireable double pole/TP&N switch disconnector - Providing and fixing following capacity double pole/TP&N sheet metal switch disconnector fuse unit in existing metal board with rewireable type fuses, including drilling holes in metal board, making connections, etc as required.

63 amps, double pole

100 amps, TP & N

S/F busbar chamber - Providing and fixing following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty, complete with all accessories including connections, earthing the body, etc. as required.100 amps

S/F S.P. MCB DB - Supplying and fixing following way single pole netural, sheet, MCB distribution board, 240 volts, on surface/recess, complete with tinned copper busbar, netural busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (But without MCB/RCCB/Isolator)

6 way, single door

8 way, single door

Supplying and Fixing TPN MCB DB: Supplying and Fixing of following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder including painting, earthing etc. as required( without MCB/RCCB/ISOLATOR). Make :- Havells / Standard / indoasian.

4 Way ,(4+12 ), double door Horizontal type

6 Way (4+18) Double Door, Horizontal type

S/F 'B' series, S.P. MCB - Supplying and fixing 6 amps to rating, 240 volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commossioning etc. as required.6/32, single pole, "B" series

S/F 'C' series SP MCB: Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make :- Havells / Indoasian / Standard.6/32A Single Pole.6/32A Single Pole

6/32A rating, SPN MCB, "C" curve 10 KA breaking capacity.

40A rating, TPN MCB, "C" curve 10 KA breaking capacity.

63A rating, TPN MCB, "C" curve 10 KA breaking capacity.

S/F DP MCB Isolator - Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required

S/F four pole MCB isolator - Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioining etc. as required

Supplying and fixing following rating four pole, (three phase and neutral) 415 volts, residual circuit breaker (RCCB) having a sensitivity current 30 milli amperes in the existing MCB DB complete with connection, testing & commissioning etc. as required.

S/F 20amps SPN MCB industrial Socket:-Supplying and fixing 20 amps 240V, SPN industrial socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP MCB insheet steel enclosure on surace or in recess with chained metal cover for the socket outlet and complete with connections, testing & commissioning etc.

Copper earth pipe electrode :-Earthing with G.I. earth pipe 4.5mtr. long 40mm dia including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal or coke and salt as required.

G.I. earth plate electrode - Earthing with G.I. earth plate 600mm 600mm x 6mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required (with charcoal or coke and salt)

Copper earth plate elecrtode - Earthing with copper earth plate 600mmx 600mm x 3mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required (But with charcoal or coke and salt)

S/L 8 SWG copper wire in ground - Supplying and laying 8 SWG copper wire at 0.50 metre below ground level for conductor earth, including soldering etc. as required

S/L 8 SWG copper wire:- Supply and fixing 8 SWG cpper wire at 0.50 metere below ground level for coductor earth electrode including soldering etc. as required.

S/L 25 mm x 5 mm G.I. earth strip in ground :-Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including soldering etc.

P/F 25mm x 5mm copper earth strip in surface/ recess :-Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc., as required.

P/F G.I. lightning conductor finial - Providing and fixing of lightning conductor finial, made of 25mm dia 300mm long, G.I. tube, having single prong at top, with 85mm dia 3mm thick G.I. base plate including holes etc. complete as required.

Fixing lightning conductor final - Fixing of lightning conductor final, made of 25mm dia 300mm long, copper tube/G.I. tube, having single prong at top, with 85mm dia 3mm thick copper base plate including holes etc. complete as required.

Reverting sweating and soldering of copper/ GI tape ( with other copper GI tape of the finial or any other metallic object) as required

P/F G.I. lightning conductor tape in horizontal run - Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)

P/F G.I. lightning conductor tape in vertical run - Provding and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)

P/F Testing joint G.I. lightning conductor - Providing and fixing testing joint, made of 20mm x 3mm thick G.I. strip, 125mm long, with 4 nos. of G.I. bolts, nuts, check nuts and spring washers etc. complete as required.

Laying copper/ G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

MV Cable Laying upto 25 Sq mm in ground:- Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc, as required.

MV cable laying upto 120 sq.mm. in ground - Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm. but not exceeding 120 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Supply of following sized SLPE insulated armoured cable (Make Havel's Polycable) 50 Sq.mm, 3.5 core

Supplying and fixing LED Batten (20/22W)

Supply of Ceiling fan 48" (1200mm)

Supply of 12" (300mm) metal exhaust fan

Supplying and fixing of 9/10 Watt LED Bulb

S/F/ Bulk head fitting with 9/10 watt CFL/LED

Supply of 12mtr. High mast in one section Construction 5355 grade as per BIEN 10 025 Top Dia 100mm, bottom dia 360mm, plate thickness 3mm, 12side polygon, galvanisation as per BS EN ISO 1461, base plate dia 520mm, base plate thickness 25mm, GI single spike Ughting protection, maximum wind speed 47m/ s as per IS : 875 (Part-III) with 6 nos foundation bols of PCD r145mm TS 600/ 24mm dia/850 mm long. Luminaries carriage : Material for 40 NB ERW Class B - M.S. Pipe, dia of carriage ring 450mm (ID) with 8 arm, welded,2 sections having carrying capacity upto S luminaries. Trailing Cable : 5 core 2.5sq.mm. PVC flexible copper conductor Winch/Power Tool : Double drum, SWL 350 Itg with 0.75HP 6 pole single speed integral motor Rope : Grade AISI 1304,7 lrope. /19 construction, dia 5mm, BLC 1450 x 2 having 2 nos of continues Aviation obstruction light: twin dome aviation obstruction lights It CO typu as required. (But excluding Feeder Pillar)

Laying of one nùmber PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 95 sq mm but not exceeding 185 sqmm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

3.5c x 35 sq.mm

Providing and fixing of XLPE, Aluminium Armoured PVC Cable confirming to IS IS7908 (Part-1) 1988 0f grade 1.1KV. Make:- Havells / Finolex / Polycab 1 R for each floor separately ,3.5 Core 50 Sq. mm. 1.1 KV XLPE Al. Ar. Cable from Main LT Panel to VTPN L.D.B Panel.

Laying of one nùmber PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding not 35 sq mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

1.1 KV Cable End Termination:- Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade as required.

3.5c x 35 sq.mm (32mm)

3.5c x 185 sq.mm (57mm)

3.5c x 70 sq.mm (38mm)

S.I.T.C of following rating recess/surface mounting round/square shape downlight with pressure die cast housing for single phase supply voltage. Luminaire shall conform to IS:3022 part-5/ section-5 or IEC:62722 with all necessary accesories as required.

80W LED Flood light

150W LED Flood light

S.I.T.C of following rating recess/surface mounting round/square shape downlight with pressure die cast housing for single phase supply voltage. Luminaire shall conform to IS:3022 part-5/ section-2 or IEC:62722 with all necessary accesories as required.

18/20W LED Round Downlight

2' X 2' LED Panel Light (34W)

S.I.T.C of following rating surface mounted LED tube lightfitting suitable for 230V 50Hz, single phase supply etc. complete as required.20w/22w LED tube

Supply, fitting, fixing and testing of 1200mm Sweep, BLDC, 5Star Fan.32 W

Providing and fixing of XLPE insulated, aluminium armoured cable including termination. Make:- Havells / Finolex / Polycab

3.5X70 mm2, 1.1kV

3.5X120mm2, 1.1kV

3.5c x 185 sq.mm

Supply of ceiling fan 48" (1200mm) BLDC Sstar 15:374:2079

Supply of Recess Mounting LED Square Down light (15/16W)

Supply of LED Street light (45/48W)

Supply fitting fixing of Recess Mounting LED Round Down light (12W)

9/10 Watt LED Bulb

Supply of LED Batten (20/22W)

Supply 15 / 16 LED bulb (essential) in existing angle holder. (Make :- Philips / Bajaj /Wipro).

Supply of 48" 1200mm ceiling fan

Supply of 12" 300mm metal exhaust fan

16" (400mm) Wall fan

Supply and fixing of LED batten (20/22W) as instructed by E/I

Supply of LED Street light (45/48W)

Silent type D.G Set of capacity 250 KVA With AMF Panel IS/IEC-6003+ 1 IS: 1460 IS: 13018

SITC of 2x20W LED Tube light.

Oil (Fuel) Filter for 250 KVA DG set

Mobil Filter for 250 KVA DG set

Air (inner + outer) Filter for 250 KVA DG set

Mobil Premium blue 15W40

Coolent inhibitor

SMPS 24V Battery charger for DG set

Supplying, installation, testing and commissioning of cubical type MV Panel made out of 14 SWG sheet steel, totally enclosed IP-54 protection, free standing, floor mounted dust and vermin proof, indoor type compartmentalized powder coated of approved shade after antirust treatment (with min seven tanks ) suitable with busbar interconnection with suitable size of copper lead/solid Aluminium strips, control circuits & bottom base channel of MS section not less than 50mmx50mmx5mm (thick), Fabrication shall be done in transportable section ,entire panel shall have a common earth busbar at rear with 2 nos earth stud cable alleys, cable gland plates in two half as required as per single line diagram & specification enclosed with the following switchgears.

INCOMER:-

250 A,50 KA, MCCB -1 no.

1 Set phase indication lights (R, Y, B)

1 No. Volt Meter (digital type) with inbuilt VSS & control fuses.

1 No. Ammeter (digital type) with inbuilt ASS

Copper BUSBAR CHAMBER:-

300amp 415 V heavy duty three phase with neutral bus bar chamber.

Outgoing

160 A,35 KA, MCCB -3 no.

DP MCB 32 A. (4 Nos.)

Supplying, installation, testing and commissioning of cubical type MV Panel made out of 14 SWG sheet steel, totally enclosed IP-54 protection, free standing, floor mounted dust and vermin proof, indoor type compartmentalized powder coated of approved shade after antirust treatment (with min seven tanks ) suitable with busbar interconnection with suitable size of copper lead/solid Aluminium strips, control circuits & bottom base channel of MS section not less than 50mmx50mmx5mm (thick), Fabrication shall be done in transportable section ,entire panel shall have a common earth busbar at rear with 2 nos earth stud cable alleys, cable gland plates in two half as required as per single line diagram & specification enclosed with the following switchgears.

INCOMER:-

160A,35 KA, MCCB -1 no.

1 Set phase indication lights (R, Y, B)

1 No. Volt Meter (digital type) with inbuilt VSS & control fuses.

1 No. Ammeter (digital type) with inbuilt ASS

Copper BUSBAR CHAMBER:-

Outgoing

4 pole MCCB 40 A,16 kA with fixed thermal magnetic setting. 5Nos.

4 pole MCCB 40 A,16 kA with fixed thermal magnetic setting.2Nos.

DP MCB 32 A. (4 Nos.)

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

MAIN DISTRIBUTION LT PANEL FOR PRINCIPAL QUARTER

Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Indoor Type Main LT Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, free standing , dust and vermin proof, (degree of protection-IP54)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated) as per Specification.

The Main LT Panel shall broadly comprise of the following equipment/components)

Incoming Feeders:-

Incomer-63A, TPN MCCB (P-2), 16 kA for 1 sec (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links- 1 No.63A, TPN MCCB (P-2), 16 kA for 1 sec (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links- 1 No. (Changeover)

Outgoing Feeders:-

63A TPN MCB 10kA - 03 Nos.

100A TPN Copper bus bar in metal encolsure with fixing clamps

Indication lamps(On- Off Trip Power On -- RYB)

Supplying, Installing, Testing & Commisioning cost of Main LT Panel for Principal quarter building all complete with all necessary items as per direction of E/I.

MAIN DISTRIBUTION BOARD FOR SRC BUILDING

Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Indoor Type Main Distribution Board fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, free standing , dust and vermin proof, (degree of protection-IP54)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated) as per Specification.

The Main Distribution Board shall broadly comprise of the following equipment/components)

Incoming Feeders:-

Incomer- 250A, TPN MCCB (P-2), 35 kA for 1 sec (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links- 1 No. (AC Mains) 100A, TPN MCCB (P-2), 16 kA for 1 sec (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links- 2 Nos. (DG OG + Changeover)

Outgoing Feeders:-

63A TPN MCCB 16kA - 02 Nos.

40A TPN MCB 10kA - 10 Nos.

63A TPN MCB 10kA - 18 Nos.

300A TPN Copper bus bar in metal encolsure with fixing clamps

Indication lamps(On- Off Trip Power On -- RYB)

Supplying, Installing, Testing & Commisioning cost of Main Distribution Board for SRC cum Library building all complete with all necessary items as per direction of E/I.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Earthwork in excavation(As per I.S. 3114/1965 for laying of different types and sizes of pipe so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of E/I.

Earth work in back filling the trenches after laying different types and size of pipes with earth removed during excavation within initial lead and lift as per specification for soil item-A& B

Supplying and fixing male ended 15 mm dia brass bib cock of approved quality (wt. not less than 350 grms) with extra socket all complete as per specification and direction of E/I.

Providing and fixing brass/C.I. stop cock of approved quality all complete as per specification and direction of E/I.(a) 15 mm dia

Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I.( Vertical type)

Vertical - 25 mm dia

Vertical - 32 mm dia

Providing and fixing N.P./C.P. brass/PVC procelain shower rose of 15mm inlet etc. all complete as per specification and direction of E/I.Shower Rose - 125mm

Providing & fixing 15mm size pillar cock C.I. body brass spindle pillar cock of approved quality as per specification & direction of E/I.

Providing and fixing Gun metal full way valve of approved quality, all complete, as per specification and direction of E/I.

25mm dia

32 mm and weight not less than 700 gms.

40 mm and weight not less than 1.0 kg.

Cutting chhajja or corince for laying G.I. pipe and restoring the same with R.C.C. (1:2:4) brick work in cement mortor (1:4) as per specification and direction of E/I.

Making holes in walls for laying G.I. pipe and restoring the same after pipe laying as per specification and direction of E/I.

125 mm thick wall

250 mm thick wall

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.

Mirror (450 x 300mm)

soap Dish container

600mm x 450mm size

Glass shelf with C.P. brass rail - 450mm x 125mm

C.P. brass towel rail 20mm x 600mm with bracket container

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I. 'P' trap 15 liters C.I. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware ware footrest to be fixed than 50 gms, 15mm PVC connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. 580mm long - With 12.5 lit. low level PVC cistern

580mm long - With 12.5 liter low level PVC cistern

B) 510 mm lonq a) With 15.0 lit. hiqh level C.l. cistern

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Supplying, fitting and fixing 40mm highb viterous white glazed earthen E.W.C. with 'P' trap of parry hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fitting with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stope cock of approved quality weight not less than 450 grams 15mm PVC alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic soild state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming all complete as per specification and direction of E/I. With 'P' trap - 12.5 lit low level PVC Cistern

(li) E.W.C. with'S' trap a) 12.5|it. low levelC.l. clstem

ii) 15 Litres

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthen ware urinal of Hindustan 'Parry' or any other approved I.S.S. make with 5 litres capacity C.i. automatic flusing cistern of reliance for any other I.S.S. approved make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grams, 15mm PVC/Alkthene pipe 450mm longwith brass coupling at both ends and doing plumber joints including priming coat of red oxide, cutting wall and floor making good the same etc. all complete as per specification and direction of E/I.Flat back or standard corner (600mm x 350mm)

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32mm C.I. brass waste, 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350 grams, 32mm PVC waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Making holes in walls for laying H.C.I. pipes and restoring the same after pipe laying as per specification and direction of E/I.

(i)125mm thick wall

(ii)250mm thick wall

Earth work in excavation for laying of different types and sizes of R.C.C. spun pipes with disposal of exacavted earth within initial lead and sizes of R.C.C. spun pipes with disposal of excavated earth within initial lead and lift as per specification and direction of E/I.

Supplying labours, tools and tackles for testing of laid, R.C.C. spun pipes upto specified lead water all complete as per specification and direction of E/I. (water to be supplied free of cost departmentally).

Lbour for alying, fitting and fixing NP2 R.C.C. spun pipe with colars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leakproof including providing sight rails, bonning rod, night guard, Red light and barrier etc. all complet as per specification and direction of E/I.150mm dia R.C.C. spun pipe

Supplying materials and labours for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600 x 450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600 x 475mm G.I. Cover with frame (weight not leaa than 36 kg) alongwith earth work in exacavation and 80mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I. 150mm dia

Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I.

25 mm dia

32 mm dia

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinalpartitions by cutting a chase of appropriate width with chase cutter andembedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade

Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank.

Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I. 150mm dia

Polythene water storage tank of ISI mark (eg Sintex /Sinter /himgiri/gangotri etc with cover & locking system

Special type C.P. Bath room Fitting for V.I.P.Buildings(JAL, Jaquar, Mark or Equivalent)

piller Cock (Long Neck) (for basin)

Bib cock long thread V.I.P

Angular Stop Cock

Concealed stop cock reduce (lSl Marked)

4 way diverter for concealed fittings

TELEPHONE SHOWER

Paper holder V.I.P.

towel rail 24 "

soap dish

Wall mixer 3 in 1 system with provision for over head shower with elbow coupling and wall flange (lSl Marked)

Tumbler Holder

Toilet Paper Holder

Glass shelf 22'

Health Faucet

Supplying laying fitting and fixing NP2 R.C.C spun pipes all complete as per direction of E/I. 150mm dia

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require.White Vitreous China Wash basin size 630x450 mm with apair of 15 mm C.P. brass pillar taps

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board - 610x510 mm bowl depth 200 mm

610x460 mm bowl depth 200 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia

32 mm nominal outer dia

Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank.

Circular type - 100mm dia

Circular type - 125 mm dia

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5

Supplying fitting & fixing G.I. pipes (Tata make) or equivalent as per I.S. 1239 (part - I)/2004 ISI marked OR medium quality (50mm dia)

Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes ,royalty etc all complete job as per direction of E/I.

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.50 mm nominal outer dia Pipes

Excavation in Soil using Hydraulic Excavator CK 90 and Tippers with disposal upto 1000 metres. (Excavation for roadwork in soil with hydraulic excavator of0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m).Including Royalty etc@ Rs. 27.48 per cum, cost of watering, rolling & compaction.Earth Cutting & Filling

a) Planting Permanent Hedges including Digging of Trenches (Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metres and supplying and planting hedge plants at 30 cm apart).Hedges

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).for plantation

Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage up to 1km (manure measured in stacks will be reduced by 8% for payment).Same as good earth

Fine dressing of the ground

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of Officer-in-charge (Cost of sludge, dump manure and/or good earth to be paid seprately

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to150 mm measured

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water).TREE Plants

Providing and displaying of Areca Palm plant, having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 20 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Schefflera high colour having ht. 25 cm to 30 cm, well developed with fresh & healthy foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and Displaying plants Allyssum white in full bloom well developed Fresh & healthy Plant in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Petunia hybrid different variety in different colour well developed with fresh and healthy foliage in full bloom in 25 cm Earthen Pot/Plastic Pot as per direction of the officer-in-charge.

Providing and stacking of plant Mogra of height 25 to 30 cm., 2 to 3 branch in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge..

Providing and stacking of Jasmine grandiflorum (chameli) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and Displaying Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot, as per direction of the officer-in-charge.

Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.

Earth Carriage -3 km

Direction and Place Identification signs upto 0.9 sqm size board. (Providing and erecting direction and place identification retro-reflectorised sign asper IRC:67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing)

Direction and Place Identification signs with size more than 0.9 sqm size board. (Providing and erecting direction and place identification retro- reflectorised sign asper IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing)

Non Schedule

AQUA INTERNATIONAL UV SS304 Drinking Water Coolers With Built In Water Puriction System (WATER FILTER)

Providing & Placing of Canteen TABLE - 1800 x 900mm. Worksurface made of 25 mm thk prelam particle board with flat pvc lipping edge banding. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high

Cafe Chair Overall Size 480W x 490D x 780H . . Base Seat & Back Made Of Moulded PP Structure Supported ( Single Piece Moulded Seat & Back Shell ) . Understructure Base Of Chair Round SS Pipe Structure Fixed Type . Understructure Base Fixed Type 19mm Dia SS Round Pipe 1.2mm Thick . Machanism & PHA ( Gas Lift ) NA . Seat & Back Are Firmly Connected To The Base Frame . Chair Max Height 780 & Depth 490mm . 440W x 410D Base Seat Moulded With PP Structure & 440W x 390H Back Seat Moulded With PP Structure . Height From Seat To Ground 420mm . All SS Round Tube Pieces Shall Be Welded Properly Strongly and conformity with regulations . Legs Of The Chair Hard Rubber Shoes . Assembly Shell Affixed On MS Frame With Help Of Screw . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Table 900W x 450D, 18mm thick PLPB top, 40x40x1.2mm CRCA powder coated frame. Table Top 18 mm Thick PLPB Board as Per Approved Laminate Shade. Understructure Made Of Prime Quality CRCA 40 x 40 x 1.2mm Square Metal Pipe. Table Top Wooden Panels Flat Edge Duly Sealed With 2mm Thick Pvc Beading. Understructure CRCA Metal Pipe 25X25mm With 1.2mm Thick Four Side Welded With Vertically Metal Pipe. Table Understructure 850W X 550D In 25 X 25 Square Pipe With 1.2mm Thick. Height Of The Understructure 700mm. Legs Of The Table Hard Rubber Shoes. All Metal Shall Be Powder Coated After Being Treated With at Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . Metal Storage ( 1D + 1S ) Made Of Prime Quality 22guage CRCA Metal Sheet Tank Treatment With Minimum 45 - 50 Micron Powder Coating. Legs Of The Table Hard Rubber Shoes. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations. CO2 Welding Shall Be Used. The product should bear, GREEN CO IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design

SDLCs are designed to provide maximum security to the lessee. Welded screws provided for extra strength of lock mounting. Door spacer plate provided for better resistance against impact load.

Seat back assembly: The seat is made up of 12 +/- 1mm thk. hot pressed plywood.The Back is made up of injection moulded glass filled nylon & upholstered using quitted Leatherette fabric. Seat Size: 470mm (W) x 515mm(D). Back Size: 450mm (W) x 553mm (H). High Resilience (HR) Polyurethane Foam: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m° and hardness 16 + 2 kgf as per IS:7888 for 25% compression. Armrest: The armrest is designed with the following features. Armrest structure which is Chrome plated & fitted with an armrest top. Fixed Armrest Top is PU moulded over metal insert. Front Pivot Synchro Mechanism: The adjustabletilting mechanism is designed with the following features. 360° revolving type. Single point control. Front-pivot for tilt with feet resting on ground ensuring more comfort. Tilt tension adjustment. 4-position locking with anti-shocK feature. Seat/back tilting ratio of 1.2. Pneumatic Height Adjustment : The pneumatic height adjustment has adjustment stroke of 10.0+-0.3. Pedestal Assembly: The pedestal is fabricated from 0.2 + 0.02 cm thick HR sheet and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 66.0+0 Scm. Pitch-center dia. Twin wheel Castors: The twin wheel castors are injection moulded in black Nylon. Quality Certification: The manufacturer should have ISO 9001:2015, ISO 50001:2018, ISO 45001:2018, ISO 14001:2015 (all ISO must be from NABCB accredited agency), BIFMA (membership), AIOTA, GREEN CO, IGBC Greenpro for the product category.

Seat Assembly: The seat assembly should be made up of 12 ± 1mm. thick hot-pressed plywood, upholstered with fabric upholstery and moulded Polyurethane foam. Seat Size: 470 mm. (W) x 480 mm. (D) Back Assembly: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. Back Size: 465 mm. (W) x 605mm. (H). High Resilience (HR) Polyurethane Foam: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. Armrest:: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. Tubular Frame: The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. Overall Dimensions of Chair: Seat Height - 460mm. Height - 935mm. Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm. Quality Certification: The manufacturer should have ISO 9001:2015, ISO 50001:2018, ISO 45001:2018, ISO 14001:2015 (all ISO must be from NABCB accredited agency), BIFMA (membership), AIOTA, Green CO , IGBC Greenpro for the product category.

Common Visitor Chair 3 seater 3 SEATER WAITING CHAIR Metal Visitor Bench Length 1775mm x Depth 690mm x Height 755mm 1)Seat & back single section 2)Seat is 410 mm from ground 3)Perforated mild steel powder coated 4)Seat thickness 1.2 mm 5)Seat width 520 mm 6)Beam MILD steel with black power coating thickness 1.6mm 7) Mild steel border with chrome plating for every seat & back 8) Mild steel handles chrome plated & die pressed legs at the end of chairs 9) Gross weight of regular 3-seater will be 31 kg.

Portrait/ Landscape Not applicable Fabric Pin Up Notice Boards-Surface: Magnetic White Board 3'x4'-Magnetic white board marker surface. Inner Core: Hard smooth particleboard. Back: Laminated sheet. Frame: Anodized aluminum. Corner: ABS Plastic, Mounting Hardware

DIAS TABLE OVERALL SIZE: 2400X900X750MM MADE OF PRELAMINATED 50MM THICK MEDIUM DENSITY FIBER BOARD SUPPORTED WITH 50 MM THICK SIDE PANNELS OF SAME MATERIAL IN BROWN-WENGE COLOR WITH

Seat & Back assembly: The seat and back are made up of 12 ± 1mm. thick hot-pressed plywood and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort topopliteal area. Seat size 470mm (W) x 480mm (D). High Resilience (HR) Polyurethane Foam. The HR poly methane seat foam is moulded with density 45+/-2 kg/m" and hardness 16 + 2 kgf as per IS:7888 for 25% compression. Armrest: The armrest is made of injection moulded from black Co-polymer Polypropylene cladded on a tubular frame. Understructure: The powder coated ( DFT 40-60 microns ) tubular frame is cantilever type & made of Ø 25.4 ±0.3mm. x 2 ± 1.6mm.thk. M.S. ER.W. Tube. Overall Dimensions of Chair Width: 614mm. Depth: 645mm. Height: 895mm. Quality Certification: The manufacturer should have ISO 9001:2015, ISO 50001:2018, ISO 45001:2018, ISO 14001:2015 (all ISO must be from NABCB accredited agency), BIFMA (membership), AIOTA, Green CO , IGBC Greenpro for the product category

Main Table Size:1350Lx750Wx750HtSupplying and placing in position of the Desk work top made out of 25mm thick pre laminated MDF board with PVC edgebanding which shall be supported on side panels & modesty panels. Side’s panels and Modesty panel should be made from 18mm thick pre laminated MDF board of approved shade. All working or non working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature. Provision of one Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of 2 drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated MDF board with provision of handles & Locking arrangement. Complete as per image and specification under the guidance of Engineer in charge.

Overall Size 915W x 485D x 1980H . Office Almirah Made Of Prime Quality CRCA Ms Sheet Panels 0.8mm Thick Powder Coated Finish With Approved Shade . Each Shelve Made Of 0.8mm CRCA MS Sheet Powder Coated . Each Shelve Shall Be Formed Such The Edges Are Bend Two Times At Right Angle. Front Shutter 1mm Thick CRCA Ms Sheet Powder Coated Riveted With Hinges. . No Sharp Edges Of Almirah Ends . All Shelve Rack Divided Into Equal Parts . Leg Shall Be 125 x 90 X 452MM 2 Nos With 1mm Thick CRCA Metal Sheet Powder Coated . Door Die Cast Chrome Plated Handles Fitted With Washer & Double Nut . Handles Ring Made Of PVC Cap . Locking Bright Bar 8-10mm Dia . Almirah All Metallic Panels Screw With Nut & Bolt . Bottom Shelve 125mm High Up To Ground . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . The product should bear IGBC Green Pro certificate for product category. Green CO And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for STORAG FURNITURE range for ergonomic design.

SEAT FOAM : 3 seater The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width (W): 206.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM. Quality Certification: The manufacturer should have ISO 9001:2015, ISO 50001:2018, ISO 45001:2018, ISO 14001:2015 (all ISO must be from NABCB accredited agency), BIFMA (membership), AIOTA,Green CO , IGBC Greenpro for the product category.

Overall Size : Width : 1000mm Depth : 650mm Height : 450mm TABLE MATERIALS: Glass of 08 mm thk tempered, Solid rubber woood legs and frame, MS sheet as bottom shelf .DECORATION MATERIALS & SPECIFICATIONS: (DENSITY / TYPE): Chrome Plating on the understructure tube, clear glass. Quality Certification: The manufacturer should have ISO 9001:2015, ISO 50001:2018, ISO 45001:2018, ISO 14001:2015 (all ISO must be from NABCB accredited agency), BIFMA (membership), GREEN CO ,AIOTA, IGBC Greenpro for the product category

Computer Table consists of Computer table with key board drawer and table top- Computer Table Top 18mm Thick PLPB Board With 2mm Thick Pvc Edgebanded Finish With As Per Approved Laminate Shade. Top Supported Understructure Of Table Gable - End Made Of Prime Quality 18mm Thick PLPB Board. Top Size 800W X 450D. 18mm Thick PLPB Wooden Shelve Fix In Table under Table Top . Right Hand Side Provided L Shape Shelve Use For CPU & UPS . Shelve Used Sliding Telescopic Channel With All Fittings. Table , Shelve & Sides Panels Flat Edge Duly Sealed With Pvc Beading . 50mm High Wooden Panel Skirting Provided in Computer Table . 7mm High Pvc Bofurs Screw With Gable . All Wooden Panels , Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment . Wooden Panels Cleaning Corner Knitted Finish . All Wooden Panels Prime Quality Board With ISI Marked . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Double Seater Bench Desk with Shelf 1.Desk size:W1200*D400*H750mm 2Bench size:W1200*D300*H440mm 3.Desk material:high quality MDF board 4.Chair material:high quality MDF board 5.Frame:metal frame,epoxy powder coated ( 5 no. of class

Teacher's Podium

Teachers Table with pedestal Size:1200mmW X500mmDx750mmH Specification: Made of prelaminated MDF board.

Revolving Chair

Visitor's Fixed Chair: 25mm CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Supply & Installation of Smart Class Arrangement in Lecture Theater – Power Podium, Audio system with 60 Watt Amplifier, Goose neck condensor microphone, 2Pc handheld wireless microphone. BENQ Short Throw Projector & Projector Wall Screen

Teacher's Podium

Teachers Table with pedestal Size:1200mmW X500mmDx750mmH Specification: Made of prelaminated MDF board.

Supply & Installation of HP/DELL make Computers with genuine WINDOWS 10 OS, Core i3 Processor- 6th Generation, 4 GB RAM, 1 TB HDD, Mouse , Keyboard & Reputed Antivirus.

Wall facing computer table with metal KBPT and CPU trolley 750 mm W X 450 mm D X 750 mm H Made of ISI marked Pre laminated MDF

Supply & Installation of Auto Restart Split AC -2 TOR with proper electrical connection & Stabilizer of repute quality. Preferably

Circular Library Rack with 2 no’s of shelf Size: 1200 m H. As per drawing. Specification: Made of ISI Marked Pre laminated Engineered Wood

Library reception table. Size: 1800 mm W X 900 mm D X 1200 mm H Specification: Made of Pre laminated MDF board

Printer table with extended top and Under storage Size: 750 mm W X 450 mm D X 900 mm H Specification: Made of Pre laminated MDF board.

Periodical Display Rack. Size: 800 mm W X 300 mm D X 1800 mm H Specification: Made of Pre laminated MDF board

Newspaper stand. Size: 800 mm W X 300 mm D X 1800 mm H Specification: Made of Pre laminated MDF board.

8 Seater Library Reading Table. Size: 1800 mm W X 900 mm D X 750 mm H Specification: Made of Pre laminated MDF board

Student's Fixed Chair: CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Full Height Cabinet with 3 Doors & Glass Shutter Size: 1200 mm D X 450 mm WX 1900 mm H Specification: Made of ISI Marked Pre laminated Engineered Wood

Wall facing computer table with metal KBPT and CPU trolley 750 mm W X 450 mm D X 750 mm H Made of ISI marked Pre laminated

Teacher’s Table with Pedestal 1200 mm W 300 mm D X 820 mm H Made of ISI Marked Pre laminated

Students Fixed Chair Specification: 16 mm CRC pipe of 18 gauze chrome Plated with moulded ply Seat back with leathered upholstery.

Supply & Installation of HP/DELL make Computers with genuine WINDOWS 10 OS, Core i3 Processor- 6th Generation, 4 GB RAM, 1 TB HDD, Mouse , Keyboard & Reputed Antivirus

Solid Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 400 mm D X 600 mm H

Modular 8 Seater Island Work Bench with 2 Base Cabinets with Electrical Raceway Specification for Work bench Made of ISI Marked Pre Laminated Engineered Wood. Size of Work bench: 2400 mm W X 1200 mm D X 820mm H SIze of Base Cabinet: 600 mm W X 600mm D X 820 mm H

Glass Shutter Full Height Cabinet Specification: Made of ISI Marked Engineered Wood Size: 900 mm W X 400 mm D X 1800 mm H

Glass Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 400 mm D X 600 mm H

table. Size: 1800 mm W X 900 mm D X 1200 mm H Specification: Made of Pre laminated board

Visitor's Fixed Chair: 25mm CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Modular Design 8 Seater Granite Top Island Work Bench with 2 Base Cabinets, Reagent Rack, Stainless Steel Sink & Tap. This is inclusive of Gas & Plumbing works Specification for Work bench Made of ISI Marked Engineered Wood. Specification for Reagent Rack : Made of Pre Laminated ISI Mark Engineered Wood Size of Work bench: 2400 mm W X 1200 mm D X 820mm H SIze of Base Cabinet: 600 mm W X 600mm D X 820 mm H ****Proper water and gas connection also needs tobe catered with entire set up

Glass Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 900 mm D X 600 mm H

Modular Design 8 Seater Granite Top Island Work Bench with 2 Base Cabinets, Reagent Rack, Stainless Steel Sink & Tap. This is inclusive of Gas & Plumbing works Specification for Work bench Made of ISI Marked Engineered Wood. Specification for Reagent Rack : Made of Pre Laminated ISI Mark Engineered Wood Size of Work bench: 2400 mm W X 1200 mm D X 820mm H SIze of Base Cabinet: 600 mm W X 600mm D X 820 mm H ****Proper water and gas connection also needs tobe catered with entire set up

Glass Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 900 mm D X 600 mm H

Visitor's Fixed Chair: 25mm CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Desk size: 1200 mm W X 400 mm D X 750 mm H Chair size: 400mmWX400mmDX440mmH Desk material: High quality MDF with melamine board Chair material: High quality board with plywood Frame: Metal frame, Epoxy powder coated

Teachers Table with pedestal Size:1200mmW X500mmDx750mmH Specification: Made of prelaminated

Supply & Installation of Auto Restart Split AC -2 TOR with proper electrical connection & Stabilizer of repute quality

Modular desk with Pedestal, Softboard & Whiteboard alongside Glass Partition , KBPT Trolley for individual Staff. Size : 900 mm W X 400 mm D X 750 mm H Material

Solid Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 400 mm D X 600 mm H

Double Seater Bench Desk with Shelf 1.Desk size:W1200*D400*H750mm 2.Chair size:W1200*D300*H440mm 3.Desk material:high quality PLPB 4.Chair material:high quality

Teachers Table with pedestal Size:1200mmW X500mmDx750mmH Specification: Made of prelaminated MDF board.

Double Seater Bench Desk with Shelf 1.Desk size:W1200*D400*H750mm 2.Chair size:W1200*D300*H440mm 3.Desk material:high quality PLPB BOARD 4.Chair material:high quality PLPB BOARD

Supply & Installation of Smart Class Arrangement in Lecture Theater – Power Podium, Audio system with 60 Watt Amplifier, Goose neck condensor microphone, 2Pc handheld wireless microphone. Short Throw Projector & Projector Wall Screen

Teacher's Podium

Supply & Installation of Auto Restart Split AC -2 TOR with proper electrical connection & Stabilizer of repute quality. Preferably

Smart Classes Compact Model for Class Rooms Inclusive of Interactive Board, Green Board, Document Camera, Wall Mounted Speakers, Smart Computer, Short Throw Projector

Modular desk with Pedestal, Softboard & Whiteboard alongside Glass Partition , KBPT Trolley for individual Staff. Size : 900 mm W X 400 mm D X 750 mm H Material : Made of Prelaminated MDF Board

Circular Library Rack with 2 no’s of shelf Size: 1200 m H. As per drawing. Specification: Made of ISI Marked Pre laminated Engineered Wood

Library reception table. Size: 1800 mm W X 900 mm D X 1200 mm H Specification: Made of Pre laminated PLPB board

Newspaper stand. Size: 800 mm W X 300 mm D X 1800 mm H Specification: Made of Pre laminated MDF board.

8 Seater Library Reading Table. Size: 1800 mm W X 900 mm D X 750 mm H Specification: Made of Pre laminated MDF board

Student's Fixed Chair CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Full Height Cabinet with 3 Doors & Glass Shutter Size: 1200 mm D X 450 mm WX 1900 mm H Specification: Made of ISI Marked Pre laminated Engineered Wood

Modular Design 8 Seater Granite Top Island Work Bench with 2 Base Cabinets, Reagent Rack, Stainless Steel Sink & Tap. This is inclusive of Gas & Plumbing works Specification for Work bench Made of ISI Marked Engineered Wood. Specification for Reagent Rack : Made of Pre Laminated ISI Mark Engineered Wood Size of Work bench: 2400 mm W X 1200 mm D X 820mm H SIze of Base Cabinet: 600 mm W X 600mm D X 820 mm H ****Proper water and gas connection also needs tobe catered with entire set up

Glass Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 900 mm D X 600 mm H

table. Size: 1800 mm W X 900 mm D X 1200 mm H Specification: Made of Pre laminated

Fixed Chair: 25mm CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Visitor's Fixed Chair: 25mm CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Modular Design 8 Seater Granite Top Island Work Bench with 2 Base Cabinets, Reagent Rack, Stainless Steel Sink & Tap. This is inclusive of Gas & Plumbing works Specification for Work bench Made of ISI Marked Engineered Wood. Specification for Reagent Rack : Made of Pre Laminated ISI Mark Engineered Wood Size of Work bench: 2400 mm W X 1200 mm D X 820mm H SIze of Base Cabinet: 600 mm W X 600mm D X 820 mm H ****Proper water and gas connection also needs tobe catered with entire set up

Smart Classes Compact Model for Class Rooms Inclusive of Interactive Board, Green Board, Document Camera, Wall Mounted Speakers, Smart Computer, Short Throw Projector Make

Modular desk with Pedestal, Softboard & Whiteboard alongside Glass Partition , KBPT Trolley for individual Staff. Size : 900 mm W X 400 mm D X 750 mm H Material : Made of Prelaminated MDF Board

Modular Desk with Pedestal Specification: Made of ISI marked Engineered wood with side panels. It is in addendum with pedestal (1 drawer & 1 shutter) Table Size: 1200mm W x 600mm D x 750mm H

Full Height Cabinet in Solid Shutter Specification: Made of ISI marked Engineered wood Size: 900 mm W X 450 mm D X 1500 mm H

Solid Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 400 mm D X 600 mm H

Visitor's Fixed Chair: CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

reception table. Size: 1800 mm W X 900 mm D X 1200 mm H Specification: Made of Pre laminated MDF board

Visitor's Fixed Chair: CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Chair- Revolving High Back

Solid Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 400 mm D X 600 mm H

Solid Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 400 mm D X 600 mm H

table. Size: 1800 mm W X 900 mm D X 1200 mm H Specification: Made of Pre laminated MDF board

Visitor's Fixed Chair: 25mm CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Visitor's Fixed Chair: CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Full Height Cabinet in Solid Shutter Specification: Made of ISI marked Engineered wood Size: 900 mm W X 450 mm D X 1500 mm H

Solid Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 400 mm D X 600 mm H

Supply & Installation of Auto Restart Split AC -2 TOR with proper electrical connection & Stabilizer of repute quality

Visitor's Fixed Chair- CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Visitor's Fixed Chair: CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Glass Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 400 mm D X 600 mm H

Full Height Office Storage Cabinet with 2 Open Storage Unit & One Full Height Cabinet Specification: Made of ISI Marked Engineered Wood Size: 2400 mm W X 450 mm D X 1800 mm H

Principal's Office Table Size: 2250 mm W X 600 mm D X 650 mm H Specification: Made of Pre laminated MDF Board, with Transitional Design, Solid Wooden Legs, with Writing Pad on top. The image is attached in the annexure. Additionally it’s provided with additional glossy finish.

Full Height Office Storage Cabinet with 2 Open Storage Unit & One Full Height Cabinet Specification: Made of ISI Marked Engineered Wood Size: 3000 mm W X 450 mm D X 1800 mm H

Chair- Revolving High Back

Visitor's Fixed Chair: CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Supply & Installation of Auto Restart Split AC -2 TOR with proper electrical connection & Stabilizer of repute quality.

Solid Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 400 mm D X 600 mm H

Desk size: 1200 mm W X 400 mm D X 750 mm H Chair size: 400mmWX400mmDX440mmH Desk material: High quality PLPB board Bench material: High quality PLBB Board

Teacher's Table Size: 1200mmW X600mmDx750mmH Material: Made of prelaminated MDF board

Supply & Installation of Auto Restart Split AC -2 TOR with proper electrical connection & Stabilizer of repute quality.

Solid Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 400 mm D X 600 mm H

Desk size: 1200 mm W X 400 mm D X 750 mm H Chair size: 400mmWX400mmDX440mmH Desk material: High quality MDF with melamine board Chair material: High quality board with

Teacher's Podium

Teachers Table with pedestal Size:1200mmW X500mmDx750mmH Specification: Made of prelaminated MDF board.

Supply & Installation of Auto Restart Split AC -2 TOR with proper electrical connection & Stabilizer of repute quality

Visitor's Fixed Chair: CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Fixed Chair: CRC pipe of 14 gauge chrome plated with molded seat back hard PVC stiched with foam & stain colour handles

Solid Shutter Over Head Cabinet Specification: Made of ISI Marked Engineered Wood Size: 600 mm W X 400 mm D X 600 mm H

SUPPLYING 250 KVA LEVEL 1 FROM IS:2026

Providing dyna super organic fertilizer special brand for Foot Ball Ground. (Product avaiable in Pune)

goal post with net

Installation OF VDF Flooring(Vaccum Dewatered Flooring) with Groove cutting & polysuphide .Rs 180per sft complete job

Fixed Basket Ball Post:- Providing and fixing of standard Basket Ball Fixed Pole Pair Regular Model- Pole will Made 8" Round MS Pipe. 3.2 Mtr EXTN. Acrylic Board Thickness -20mm (Imported Quality ),Size Of Board -180cm x 105 cm. Dunking Ring Quality Net White Colour Epoxy Painted White Color( including all Civil Work For Grouting in Ground ,All Acessories ,Freight, Unloading ,base Plate if required and hifting)". (Including all item's)

Water Sprinkler System

S/F/F 250 watt HPSV fitting complete set

S/F 32 Amp D.P. switch

Fixed Volleyball Post : Exact Size-8.2FT Pipe Size -3" & 4" Pipe Shape -Round Pipe Thickness -2.5-3.2 mm. Gauge Of Steel -10 to 8 gz Make Of MS Pipe -Apollo or Equivalent With Ratchet For New Tightnening And UPright Sockets For Height Adjusment MEN/ WOMEN EpoxyRed poles & yellow Upright Sockets Paints.

Pre-Cast Concrete reinforcement Bench (Chair type Bench with back rest) consisting of 2 nos. L-shaped base support of thk. 100 mm, back height 1000 mm & front height 450 mm. Base width – 620mm and 5 nos. Reinforced concrete planks in specified colour, of size 1500x100x50, 1nd 1 no plank of size 1500x200x50 mm manufactured by using M30 grade of concrete & reinforced suitably to prevent damage during handling, transportation, erection and long use. All parts joined together with nuts & bolts of suitable size. Bench top and bench planks are treated with paint Erection of the bench to be done by us (Cost includes 10% CP & 5 % OHC)

Supply & fitting of ShyamJyoti™ LED Based Solar Street Lighting System Luminary : 12W LED Luminary Luminary Housing- Weather Proof Housing Structure- Hot Deep Galvanized Module Pole : Hot Deep Galvanized MS Pole (4.5 Mtr.) Battery Box : Corrosion Resistant Painted Power Coated Metal Battery Box Other : Suitable Cable, Etc. Battery : 19.8Ah 14.8V Lithium-Ferro Battery of MNRE Approved Module : 75Wp of HBL / Gautam Solar/IEC Equivalent (Cost includes 10% CP & 5 % OHC)

Providing, laying, testing & commissioning of ’C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required

150mm dia.(Pump room)

100 mm dia. (Pump room)

80 mm dia.(Pump room)

150mm dia.(Ring Line)

80 mm dia.(Ring Line)

25 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required

150mm dia

100 mm dia.

80 mm dia.

18.12 Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 100mm Dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

150mm Dia

80mm Dia

18.15 Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150mm Dia

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as reouired : a) Single Headed

18.16 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required . Gun Metal

18.18 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required:. Gun Metal

Providing and fixing MS Double Door Hose Box with lockable arrangements to accommodate 2 RRL hose of 30 M length and 1 no. branch pipe, painted white inside and red outside with one key.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required

Supply and installation of Pressure gauges of suitable range for pump sets with Ball valves, siphon, Fittings like unions / colors / reducers , etc.

Supply and installation of Pressure switches of suitable range for pump sets with Ball valves, Fittings like unions / colors / reducers etc.(Pipe size 25mm Dia) As per specification and drgs Including 25 mm piping from main header to manifold.

(A) Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (C) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-’F' insulation, conforming to IS-325. (D) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered with anti vibration pads. 1620 Ipm at 56 m Head

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) (B) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 HzAC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-’F'insulation, conforming to IS : 325.(D) M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads.180 lpm at 56m head

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-’F' insulation, conforming to IS-325. (D) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads.900 Ipm at 56 m Head

Supplying, laying, testing & commissioning of FS, PVC outer sheath, steel armoured, aluminium / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray /on walls/ floor etc. as required. For cables laid In door the rate shall include. The rate shall be include with cable terminations with Al. / Cu. lugs, cable glands, PVC insulation tapes and all other accessories as required.

3.5C x 120 sq.mm ( XLPE Aluminium cable for main pumps)

4 C x 16 Sqmm. ( XLPE aluminium cable for Jockey pumps)

2 C x 2.5 Sqmm. (Copper armoured cable for Instrumentation)

Providing, laying, testing & commissioning of ’C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required

150mm dia

100 mm dia

80 mm dia.

65 mm dia.

50 mm dia.

40 mm dia.

25 mm dia

18.11 Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required . 150 mm dia.

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type blank Gunmetal/Stainless Steel cap and chain as required : a) Single Headed

18.16 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required . Gun Metal

18.18 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required:. Gun Metal

Providing and fixing MS Double Door Hose Box with lockable arrangements to accommodate 2 RRL hose of 30 M length and 1 no. branch pipe, painted white inside and red outside with one key.

18.17 Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30m

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type. 15mm Dia

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as reouired. 10 Zone

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

17.5.2 Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Providing and fixing Carbon di Oxide fire extinguisher consisting of welded MS cylindrical body, squeeze lever, discharge valve, fitted with internal discharge tube, high pressure discharge hose, discharge nozzle, suspension bracket, finished externally with red enamel paint, & fixed to wall with brackets with initial charger.Make :- Kartar/Safeguard/ATASEE. Capacity 4.5 kg ISI Marked

Providing and fixing ABC Extinguisher consisting of welded MS cylindrical body with discharge valve, nozzle and hanging arrangement complete.Make :- Kartar/Safeguard/ATASEE. a) Capacity 6 kg ISI Marked

Add GST 18 %

Add Labour cess 1%

M/s. R.S. AGRAWAL (BID ID -640056)