GE 861 EWS-11 (T)/ 2025-26

Amount

Demolition of brick work or stone boulder masonry built in cement mortar including all arches quoins etc but excluding ashlar facing, dressed stone work & precast concrete articles etc complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store complete all as specified and directed by Engineer-in-Charge.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in any mortar, complete all as specified and directed by Engineer-in-Charge.

Dismantling mild steel/cast iron work of any description, complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors & paving n.exc 15 cm thick (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n.exc 1.5 sqm complete all as specified and directed by Engineer-in-Charge.

Taking down chowkat or frame with shutters (without taking shutter from the frame) exceeding 1.5sqm and not exceeding 4.00 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down of shutter any description area exceeding 1 sqm but not exceeding 2 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description area n.exc 1.00 sqm each complete all as specified and directed by Engineer-in-Charge.

Dismantling wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets & snap grid frame etc, complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantling framed work 40 sq cm and over in section in any position, complete all as specified and directed by Engineer-in-Charge.

Dismantling fillets, rails, Scantling etc un framed wk under 40 sqcm fixed in any position with nails complete all as specified and directed by Engineer-in-Charge.

Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed by Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed by Engineer-in-Charge.

Taking down shutter and Refixing the same opening of any description in same opening exc 1 Sqm and n.exc 2 sqm complete all as specified and directed by Engineer-in-Charge.

M & L for Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:6, complete all as specified and directed by Engineer-in-Charge.

All as per the description of item No. 19 here-in- above but except bricks complete all as specified and directed by Engineer-in-Charge.

M & L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth using water proofing compound and without using extra cement, complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 5mm thick on concrete surfaces in CM 1:3 on ceiling, finished even and smooth complete all as specified and directed by Engineer-in-Charge.

Supply only liquid water proofing compound of approved quality, complete all as specified and directed by Engineer-in-Charge.

M & L for 10mm thick rendering on fair faces of brick or concrete surfaces in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

M & L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed by Engineer-in-Charge.

M & L for Glazed ceramic coloured tiles 450mm x 300mm x 6mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed by Engineer-in-Charge.

M & L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but not exc 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed by Engineer-in-Charge.

S&F 605mmx605mm GI frame work for seamless celling snap grid frame work for false ceiling with all necessary angle & Tee arrangement with and incl fixing cleats screw etc complete all as specified and directed by Engineer-in-Charge.

S&F hanger 6mm dia G I (upto 1200 mm length) adjusting level fixed to roof by means of celling complete all as specified and directed by Engineer-in-Charge.

S&F false ceiling 8mm thick (Non asbestos fibre cement building board) fixed in celling flat or sloping inserted in GI/aluminium frame work complete all as specified and directed by Engineer-in-Charge.

M&L for chequered cement concrete tiles 30cm x30cmx25mm thick (glossy finished) with grey cement and pigment , set , jointed and pointed in neat cement slurry in floors laid over 15 mm thick screed bed in cm 1:6 complete all as specified and directed by Engineer-in-Charge.

M & L for 60mm thick factory made machine pressed precast concrete coloured interlocking paver block with grey cement and pigment, any shape, size and design as approved by Engineer-in charge confirming to IS 15658-2006, M-35 grade, complete all as specified and directed by Engineer-in-Charge.

40mm thick PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in floors, finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.(floor to be laid in panels)

M&L for glass dividing Strips, 3mm thick and 38mm width of strip and inserted in position to confirm to design complete all as specified and directed by Engineer-in-Charge.

M & L for Sand filling under floors or in foundation including watering and consolidation, complete all as specified and directed by Engineer-in-Charge.

M & L for 75mm thick PCC 1:4:8 type D-2 (40 mm graded stone aggregate) as in sub-floor, sub-base, floor and pavings, etc., complete all as specified and directed by Engineer-in-Charge.

M & L for Plain cement concrete 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 50mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays, all as specified and directed by Engineer-in-Charge. Note:- The unit rate include for use of form work (straight or curved).

M & L for Plain cement concrete 1:2:4 mix type B0 (using 12.5 mm graded stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates, hold fast and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work complete all as specified and directed by Engineer-in-Charge.

S & F Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and directed by Engineer-in-Charge.

S & F Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed by Engineer-in-Charge.

M & L for 2nd class softwood, plain, solid, straight chowkats and frames, wrought, framed, wrought, framed rebated on the solid, rounded of chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed by Engineer-in-Charge.

M & L for 35mm thick, 2nd class softwood factory made, plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces, kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified and directed by Engineer-in-Charge.

M & L for 35mm thick, 2nd class softwood factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge, etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters, complete all as specified and directed by Engineer-in-Charge.

M&L for Powder coated aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos including 5.5 mm thick tinted sheet glass ordinary quality in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified and directed by Engineer-in-Charge.

M&L for Powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (2 no.). hinges type B-21 100mm long (2 no.) suitable handle (2no.) including 5.5 mm thick tinted sheet glass ordinary quality in each leaf complete all as specified and directed by Engineer-in-Charge.

S&F Powder Coated Anodised aluminium frame (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge.

S & F box type steel windows/ ventilators (Factory made) outer frame made out ERW tube 'P' section 65mm X 45mm X 25mm and shutter with glazed openable shutter of ERW tube 'P' section 50mm X 35mm X 20mm openable (double) shutter with glazed openable shutter on (external side) and wire gauged openable shutter on (internal side) with steel pintel hinges, steel handle 100mm long, mild steel tower bolt 02 nos on each shutter, stopper of 'Z' section and its locking arrangement at mild steel hook and eye including 0.36 mm dia nominal dia of stainless steel wire cloth average width of aperture 1.4mm dia, 4mm thick sheet glass window and 4mm figured glass for ventilators and guard bars (MS square bar 12mm dia), complete all as specified and as directed. (Ref Drg No. CESZ/TD-1018/2011, SHEET 1/1 to 3/3) Note: The quoted rate against the above item shall also include (i) For provn of one shop coat of zinc chromate primer on all exposed steel surfaces and coat tar on the ends of steel frame in contact with bricks/ concrete surface. (ii) 04 Nos MS Steel Lugs of 20 X 5mm, MS flat 20 cm long overall welded to frames. (iii) PCC block for embedded lugs. (iv) 0.36mm dia SS wire mesh. (v) 4mm thick sheet glass for window. (vi) Guard bars 100mm centre to centre.

M & L for 6mm thick plywood, grade BWR, type BB, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed by Engineer-in-Charge.

M & L for 6mm thick plywood, grade BWR, type BB, fixed in walls with nails to timber frame, complete all as specified and directed by Engineer-in-Charge.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

M & L for 2nd class softwood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm, complete all as specified and directed by Engineer-in-Charge.

M & L for 2nd class softwood plain fillets bull nosed splayed chamfered or rounded on one edge or face in section of sectional area exc 3 Sqcm but n exc 6 Sqcm complete all as specified and directed by Engineer-in-Charge.

M & L for 2nd class softwood plain fillets bull nosed splayed chamfered or rounded on one edge or face in section of sectional area n.exc 3 Sqcm complete all as specified and directed by Engineer-in-Charge.

M & L for 2nd class softwood, as in scantling and similar work, clean sawn, timber fixed in position, complete all as specified and directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed by Engineer-in-Charge.

S & F 250mm size mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engineer-in-Charge.

S & F 150mm long mild steel barrel tower bolts, stove enamelled black, with bright bolts fixed, complete all as specified and directed by Engineer-in-Charge.

S & F 150mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed by Engineer-in-Charge.

S & F 100mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed by Engineer-in-Charge.

S & F in repair 300mm long mild steel ordinary rat tail rod pattern, springs including roller and roller plate fixed to wooden chowkhat, complete all as specified and directed by Engineer-in-Charge.

S&F in repair stainless steel sink , made out of 1.00 mm thick sheet for kitchen with plug, washer pipe cast iron cantilever brackets, connecting union overall size 495x420mm bowl size 410mm x 330mm x160mm all as specified and directed by Engineer-in-Charge. Make: Nirali/Diamond/Blue King/Kingston/

S&F in repair stainless steel sink , made out of 1.00 mm thick sheet of overall size 600x750mmx250mm all as specified and directed by Engineer-in-Charge. Make: Nirali/Diamond/Blue King/Kingston.

S&F in repairs Floor door stopper of Overall length of cover plate 150mm aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed by Engineer-in-Charge.

S & F Door closer hydraulically regulated, Aluminium (extruded section) body designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed.

M & L for 4mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed by Engineer-in-Charge.

M & L for 4mm thick figured glass pin headed type and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

M & L for Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples, complete all as specified and directed by Engineer-in-Charge.

M & L for Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples (fixed in repair), complete all as specified and directed by Engineer-in-Charge.

M & L for Steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed by Engineer-in-Charge.

All as per the description of item No. 71 here-in- before but except tubing complete all as specified and as directed by Engineer-in-Charge.

M & L for Steel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed by Engineer-in-Charge.

All as per the description of item No. 73 here-in- before but except tubing complete all as specified and as directed by Engineer-in-Charge.

M & L for Rotational moulded polyethylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismantling of existing tank, complete all as specified and directed by Engineer-in-Charge.

M & L for Rotational moulded polyethylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismantling of existing tank, complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitreous china, wash hand basin, flat back of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, including 32mm dia PVC waste fitting, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) but including PVC (SWR) 'P' trap, jointing to flush pipe complete and making good to floor in cement concrete M-5 (1:5;10), type E-2 using 40mm graded crushed stone aggregate, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, seat cover and fixing bolts, flushing cistern and flush pipe & making good to floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated), complete all as specified and as directed.

S & F in repair 32 mm dia waste coupling of PTMT (half or full threaded) (minimum weigh 45 gms) complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets, complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed by Engineer-in-Charge.

S & F in repair for 125mm size brass chromium plated shower rose with or without swivel joints, any size including fixing to steel pipe of 15mm dia or union, complete all as specified and as directed by Engineer-in-Charge.

S & F in repair 15mm bore bib tap, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed by Engineer-in-Charge.

S & F in repair 15mm dia pillar taps, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered 'Hot' and 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15mm bore Stop valves/ angle valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15mm bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed (minimum weight 15 mm - 90 grms/20mm -125gms) complete all as specified and directed by Engineer-in-Charge.

S&F in repair 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed(minimum weight 20mm -210 gms complete all specified and directed by Engineer-in-Charge.

S&F in repair health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connection and fixed in position complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed, complete all as specified and directed by Engineer-in-Charge.

S&F in repair 20mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed, complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15 mm bore brass CP mixer for mixing hot and cold water screwed down for iron pipe and fixed, complete all as specified and directed by Engineer-in-Charge.

S&F s/s Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

S & F in repair 75mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed by Engineer-in-Charge.

S & F in repair 100mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 75mm dia outlet PVC (SWR) floor trap with grating including jointing with solvent cement, complete all as specified and directed by Engineer-in-Charge.

M & L for Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of alkali-resistant priming coat, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over wall putty, on plastered surfaces preparatory to distempering, complete all as specified and directed by Engineer-in-Charge.

M&L for applying two coat of white wash on ceiling surface complete all as specified and directed by Engineer-in-Charge.

M & L for Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed by Engineer-in-Charge.

M&L in repairs for weather boarding in 2nd class softwood clean swan , plain , 20 mm thick or feather edeges , 15 mm to 20 mm th and fixed with 30 mm laps joints complete all as specified and directed by Engineer-in-Charge.

S&F framed work such as grills and gratings etc with ends of bars shouldered and /or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, water staging etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair stainless steel Curtain/drapery rod 20 mm dia as approved colour/design in one length with clamps, ring, ball shaped knobs at both end, complete all as specified and directed by Engineer-in-Charge.

S & F in repair Glass shelf assembly 600mm, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces of walls, plastered or unplastered including brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and treating oil and greasy spots and applying one coat of white wash on wall, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces of ceiling, plastered or unplastered including brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and treating oil and greasy spots and applying one coat of white wash on ceiling, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces of walls, plastered or unplastered including brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and treating oil and greasy spots and applying one coat of white or tinted oil bound distemper on wall, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces of walls, plastered or unplastered including brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and treating oil and greasy spots and applying two coats of oil bound distemper, white or tinted, on wall, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces of walls, plastered or unplastered including brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and treating oil and greasy spots and applying one coat of cement based paint on wall, complete all as specified and directed by Engineer-in-Charge. NOTE: Work to be carried upto 10m height.

M&L for preparation of old surfaces of walls, plastered or unplastered including brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and treating oil and treating spots and applying one coat of weather proof exterior acrylic emulsion in camouflage pattern on wall, complete all as specified and directed by Engineer-in-Charge. NOTE: Work to be carried upto 10m height.

M & L for complete removal of existing treatment from surfaces of walls by wire brushing and washing down and stopping of surfaces and preparation of surfaces by laying with 3mm thick wall care putty as required to obtain smooth and even surface and then applying two coats of oil bound distemper white or tinted, on walls, complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old painted wooden surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old painted GI/steel surfaces of any description not otherwise described over 10cm width or girth as in roof and applying one coat of synthetic enamel paint complete all specified and directed by Engineer-in-Charge. NOTE: Work to be carried upto 10m height.

M & L for 15mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

M & L for writing letters or figures (Block, Roman, Italic or Indian) n exc. 30 cm high complete all as specified and directed by Engineer-in-Charge.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including unscrewing from board fitting and fixture such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody for reuse if serviceable or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engineer-in-Charge.

Point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable maintaining colour coding (Phase- Red/yellow/Blue, Neutral- Black) and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and including PVC casing and capping/Conduit medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size or PVC Gang Box with 3 mm thick plastic laminated sheet cover of adequate size for one light point/fan point controlled by one switch and making good disturbed surfaces with CM (1:3) to match with the existing surface, complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-118 here in above but for one 3 pin 5A socket outlet independent controlled by one switch, complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-118 here in above but for one 5A socket outlet on the same board controlled by one switch, complete all as specified and directed by Engineer-in-Charge.

All as per serial item No 118 here-in-before but for 3 pin 15 Amps socket outlet independent board with 2.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead, complete all as specified and directed by Engineer-in-Charge.

M&L for Concealed Point wiring complete with 1.5 sqmm 1100 graded PVC FRLS (Multistranded) insulated unsheathed copper conductor single core multi strand flexible cable maintaining colour coding (Phase- Red/yellow/Blue, Neutral- Black), PVC conduit not less than 20mm dia concealed, including cutting chases, finishing of slots by means of cement mortar 1:3 making good to existing surface of the wall and touching with three coats of existing colour of wall and making good disturbed surface complete sunk in pressed steel terminal boxes of required size not less than 1.6mm thick factory made and factory painted with top cover 3mm thick plastic laminated sheet fixed with brass screw and washers with all accessories including single core multistranded copper conductor 1.5 sqmm size cable (green colour) as earth continuity wire connected to common earth dolly to modular concealed box and white cover plate of required nos and required size for housing switches, sockets etc for one light / fan/ bell point controlled by one switch one way and making good disturbed surfaces with CM (1:3) to match with the existing surface, complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-122 here in above but for one 3 pin 5A socket outlet independent controlled by one switch, complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-122 here in above but for one 5A socket outlet on the same board controlled by one switch, complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-122 here in above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead, complete all as specified and directed by Engineer-in-Charge.

S&F ceiling rose 3 terminal bakelite 65mm x50mm surface type, PVC/ Polycarbonate, isolated body, complete all as specified and directed by Engineer-in-Charge.

S&F Switch piano flush button types 6 Amp, single pole, one way complete all as specified and directed by Engineer-in-Charge.

S&F Switch socket combination 2 in 1, 3 pin, 5 Amp flush type, universal, complete all as specified and directed by Engineer-in-Charge.

S&F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp, flush type universal, complete all as specified and directed by Engineer-in-Charge.

S&F Lamp holder, PVC/ Polycarbonate type with back plate, straight/ angular suitable for batten fittings, complete all as specified and directed by Engineer-in-Charge.

S&F Bell push, flush type, 5 Amp, complete all as specified and directed by Engineer-in-Charge.

S&F in repair of Call bell , ding dong AC single phase, 230 volts 50 Hz including wooden/ PVC board of suitable size, connecting and testing, complete all as specified and directed by Engineer-in-Charge.

S&F Fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically complete all as specified and as directed by Engineer-in-Charge.

S&F in repair of Modular switch 1 way 6A,1 module complete all as specified and as directed by Engineer-in-Charge. Make: Anchor/Roma/Legrand/ goldmedal

S&F in repair of Modular switch 1 way 16A,1 module complete all as specified and as directed by Engineer-in-Charge. Make: Anchor/ Roma/ Legrand/ goldmedal

S&F in repair of Modular socket, 6A - 2/3 pin combined 2 modules complete all as specified and directed by Engineer-in-Charge.

S&F in repair of Modular socket 6/16A,2/3 pin, combined 2 module complete all as specified and directed by Engineer-in-Charge.

S&F in repair of Modular fan step regulator, 120W - 2 modular complete all as specified and directed by Engineer-in-Charge.

S&F in repair of White cover plate with frame, 2 module complete all as specified and directed by Engineer-in-Charge.

S&F in repair of White cover plate with frame, 4 module complete all as specified and directed by Engineer-in-Charge.

S&F in repair of White cover plate with frame, 6 module complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair, Plug top 3 pin 5/6 amps 230 volts, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair Plug top 3 pin 15/16 amps 230 volts, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair PVC Gang box surface type suitable for fixing of 5 pin 5 Amp multipurpose switch socket on wall complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair PVC Gang box surface type suitable for fixing of 5 pin 15 Amp multipurpose switch socket on wall complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair LED 9 watt pin type bulb, complete all as specified and directed by Engineer-in-Charge.

LED light fitting 1 x 10 Watt , 2 ' long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use pack including LED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with three core twisted flexible copper conductor cable with suitable size LED tube including taking out old, complete all as specified and directed by Engineer-in-Charge.

LED light fitting 1 x 18 Watt , 4 ' long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use pack including LED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with three core twisted flexible copper conductor cable with suitable size LED tube including taking out old, complete all as specified and directed by Engineer-in-Charge.

S&F in repair of LED light fitting 1 x 18 Watt , 4 ' long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use pack including LED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with three core twisted flexible copper conductor cable with suitable size LED tube including taking out old, complete all as specified and directed by Engineer-in-Charge.

S&F in repair of LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engineer-in-Charge.

S&F in repair LED light fitting 12watt 220 volts AC round shape/ square shape recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair Exhaust fan ventilating type of plastic body of size 250 mm sweep complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz including taking down all as specified and directed . Make HavellsCat part No. DXWHT/BLK or equivalent in CG, Bajaj , philips .

Supply and fix in repair Ceiling fan complete with blades, down rods, electronic regulator and accessories,230 v, 1200mm sweep. min air delivery 210 CFM with service value 6.00 BEE . Five stare rated with brushless direct motor (BLDC) complete and connecting up including provision of with copper standard conductors cables from ceiling rose/ connector to Fan including taking down all as specified and directed . Make Bajaj/ Havells /CG

Supply & fixing in repair MCB Distribution board , 240 volts single pole and neutral , double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 4 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair MCB Distribution board , 240 volts single pole and neutral , double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 8 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair MCB distribution board , 240 volts single pole and neutral , double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 12 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed by Engineer-in-Charge.

S&F in repair of double door type vertical type TPN DB 4 Way ,415V with 200A busbar , with metallic double door type IP 43 IK 09 protection suitable for housing MCCB's complete all as specified and directed by Engineer-in-Charge. NOTE :- DBs shall be concealed in wall whereever possible including making good the surface to match with surrounding complete all as specified and directed by Engineer-in-Charge.

S&F MCCB FP 63 Amps,16KA, 415 volt, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement of for MCB single pole 240 volts, 'B' curve of rating 6 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement of for MCB single pole 240 volts, 'B' curve of rating 10 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement of for MCB single pole 240 volts, 'B' curve of rating 16 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement of for MCB single pole 240 volts, 'B' curve of rating 25 amps, as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement of MCB single pole neutral (SPN) 32 Amps 240 Volts, 'C' curve, with rupturing capacity 10 KA, complete as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement of MCB single pole neutral (SPN) 40 Amps 240 Volts with rupturing capacity 10 KA, complete as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement of MCB TPN 415 volts, 40Amps 'C' Curve 10 kA capacity, complete all as specified and directed by Engineer-in-Charge.

Sub main wiring with two single core PVC insulated flexible copper conductor cable of size 2x 1.5 sqmm + 1x 1.5 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 1.5 sqmm as earth lead in & including PVC casing capping medium grade 2mm thickness ISI marked incl taking down old unsv, complete all as specified and directed by Engineer-in-Charge.

Sub main wiring with two single core PVC insulated flexible copper conductor cable of size 2x 2.5 sqmm + 1x 2.5 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 2.5 sqmm as earth lead in & including PVC casing capping medium grade 2mm thickness ISI marked incl taking down old unsv, complete all as specified and directed by Engineer-in-Charge.

Sub main wiring with two single core PVC insulated flexible copper conductor cable of size 2x 4.0 sqmm + 1x 4.0sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 4.0 sqmm as earth lead in & including PVC casing capping medium grade 2mm thickness ISI marked incl taking down old unsv, complete all as specified and directed by Engineer-in-Charge.

Sub main wiring with two single core PVC insulated flexible copper conductor cable of size 2x 6.0 sqmm + 1x 6.0sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 6.0 sqmm as earth lead in & including PVC casing capping medium grade 2mm thickness ISI marked incl taking down old unsv, complete all as specified and directed by Engineer-in-Charge.

Supply and laying in repair service cable 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed 16 sqmm 2 Core nominal cross section complete all as specified and directed by Engineer-in-Charge.

Supply and lay in repair cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded copper conductor of size 16 sq mm 4 core. laid in trench/ duct / along pole/wall etc including making connection complete all as specified and directed by Engineer-in-Charge. Note : The cost of thimbles/lugs and cable gland etc is incl in quoted rate and no extra payment will be made for it.

Supply & fix in repair medium grade PVC casing and capping of size 20 mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc, complete all as specified and directed by Engineer-in-Charge.

Disconnectiong, taking down, strip opening, cleaning all parts and packing of exhaust fan of any make and size & greasing ball bearing with specified quality grease & recommisioning the same including making new electric flexible wire connection, complete all as specified and directed by Engineer-in-Charge. NOTE: Replacement of spare parts, rewinding, painting etc to be measured and paid separately.

Disconnectiong, taking down, strip opening, cleaning all parts and packing of ceiling fan of any make and size & greasing ball bearing with specified quality grease & recommisioning the ceiling fan including making new electric flexible wire connection, complete all as specified and directed by Engineer-in-Charge. NOTE: Replacement of spare parts, rewinding, painting etc to be measured and paid separately.

Replacement of short circuit/over-heated windings from starter of ceiling fan of any make having 1200/1400mm sweep with matching guage & turns of super enamelled copper winding wire complete with leathered paper, glass sleeves, varnishing, baking, heating, drying, cleaning fan bearing/bushes, greasing, oiling and reassembling of fan with testing etc, complete all as specified and directed by Engineer-in-Charge.

Replacement of short circuit/over-heated windings from starter of exhaust fan of any make having 300mm/350mm/450mm sweep with matching guage & turns of super enamelled copper winding wire complete with leathered paper, glass sleeves, varnishing, baking, heating, drying, cleaning fan bearing/bushes, greasing, oiling and reassembling of fan with testing etc, complete all as specified and directed by Engineer-in-Charge.

M&L for replacement of gun metal bush with suitable size for ceiling fan any make, any size and any sweep, complete all as specified and directed by Engineer-in-Charge.

M&L for replacement of ball bearing suitable for 1200mm/1400mm sweep ceiling fan of any size any make, complete all as specified and directed by Engineer-in-Charge.

M&L for replacement of approved quality connector block of ceiling fans of suitable size, complete all as specified and directed by Engineer-in-Charge.

M&L for replacement of capacitor 2.5 mfd AC 230 volts 50 Hz, complete all as specified and directed by Engineer-in-Charge.

M&L for replacement of ball bearing suitable for 300mm/450mm sweep exhaust fan, complete all as specified and directed by Engineer-in-Charge.

M&L for replacement of capacitor 3.15 mfd AC 230 volts 50 Hz, complete all as specified and directed by Engineer-in-Charge.

Taking down water storage heater of capacity 25/35/50 ltr from the site and opening base plate assy and removing all sludge and scaling from the inner tank and refixing the the base plate assembly with and including minor spares such rubber gasket, piece of wire etc, complete all as specified and directed by Engineer-in-Charge.

S&F Heating element AC 230 Volt of rating 1500W ISI mark as per existing any type, complete all as specified and directed by Engineer-in-Charge.

S&F Heating element AC 230 Volt of rating 2000W ISI mark as per existing any type, complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Thermostat switch AC 230 Volt adjustable range from 0-90 degree Celsius, complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of flexible PVC connection pipe heavy duty suitable for hot water to bear the temperature 100 degree Celsius with out let and inlet connection brass adaptor and PVC washer having size 450 mm long 15 mm nominal dia complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of auto-cut switch suitable for geyser 25-50 ltrs 230 volts AC all as per sample, complete all as specified and directed by Engineer-in-Charge.

S&F in repair inner tank assembly made of copper suitable for 25 ltr storage type water heater with and including nuts, bolts and washer and fusible plug, complete all as specified and directed by Engineer-in-Charge.

S&F in repair inner tank assembly made of copper suitable for 35 ltr storage type water heater with and including nuts, bolts and washer and fusible plug, complete all as specified and directed by Engineer-in-Charge.

S&F in repair inner tank assembly made of copper suitable for 50 ltr storage type water heater with and including nuts, bolts and washer and fusible plug, complete all as specified and directed by Engineer-in-Charge.

S&F in repair glass wool for insulation purpose in any make and any capacity storage type water heater complete all as specified and directed by Engineer-in-Charge.

S&F in repair outer body including upper and lower cover and inspection plate made of MS sheet duly painted with super enameled synthetic paint over a coat of steel primer suitable for 25 Ltr storage type water heater, complete all as specified and directed by Engineer-in-Charge.

S&F in repair outer body including upper and lower cover and inspection plate made of MS sheet duly painted with super enameled synthetic paint over a coat of steel primer suitable for 35 Ltr storage type water heater, complete all as specified and directed by Engineer-in-Charge.

S&F in repair outer body including upper and lower cover and inspection plate made of MS sheet duly painted with super enameled synthetic paint over a coat of steel primer suitable for 50 Ltr storage type water heater, complete all as specified and directed by Engineer-in-Charge.

S&F in repair three core cable 1100 volt grade having size 40/0.0076 copper conductor multi stranded, complete all as specified and directed by Engineer-in-Charge.

M/S HAFIZ AND SONS (BID ID -3324415)

M/S TANTRAY AND CO (BID ID -3326725)

JANDOO AND CO (BID ID -3326543)

M/S Manzoor Constructions (BID ID -3325994)

M/S ABDUL KARIM RATHER (BID ID -3328971)