PROVN TO TECHNICAL TRAINING FACILITIES (PRACTICAL/TRAINING, LABORATORIES, TRADE TRAINING SHOP AND TRAINING OF STORE) OF 22 RAPID (S) SIG REGT (AREN) UNDER AGE B/R-IV AND AGE E/M-II OF GE (SOUTH) MEERUT CANTT

Amount

Surface dressing and site clearance n exc 15 cm deep incl site clearance in soft/ loose soil complete all as specified and directed.

Excavation in trenches not exc. 1.5 metre wide and not exc. 1.50 metre in depth for foundation etc and for manholes etc n.exc. 10 Sqm on plan and n.exc. 1.5 metre depth and getting out in soft/loose soil complete all as specified and directed.

Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface Complete all as specified and directed.

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Removing excavated materials (soils) to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.50 above the starting point complete all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick as in soft/loose soil complete all as specified and directed.

Material & labour for approved soil filling under the floors, spreading and leviling in layers n.exc 25 cm thick, well ramming including watering as required complete all as specified and directed.

Material & labour for cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete and sub base of floor complete all as specified and directed.

Use and waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

Use and waste of Form work of sides of pillars, posts, struts, piers, columns etc square or rectangular or polygonal rough surfaces of concrete complete all as specified and directed.

M&L Form work to sides and soffits of beams lintels etc finished fair Complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick flat fair finished surfaces of concrete complete all as specified and directed.

M&L for form work to the edge of concrete flat n. exc 200 mm thick Complete all as specified and directed.

Supply & fix mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Supply & fix mild steel TMT bars 5 mm dia and over upto and including 10mm dia as in stirrups complete all as specified and directed.

M&L Reinforced cement concrete M-25 design mix (using 20 mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L Reinforced cement concrete M-25 design mix (using 20 mm graded stone aggregate) as in Columns, pillars etc Complete all as specified and directed.

M&L Reinforced cement concrete M-25 design mix (using 20 mm graded stone aggregate) as in beams, lintels over 1.5 m span etc complete all as specified and directed.

M&L Reinforced cement concrete M-25 design mix (using 20 mm graded stone aggregate) for roof slabs supported on walls, beams and the like complete all as specified and directed.

Material & labour brick work with fly ash bricks in CM 1;6 brick straight or curved on plain exeeding 6m mean radius complete all as specified and directed.

Material & labour for 10 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material & labour for 15 mm thick rendering on fair faces of brick work or concrete surfaces,in CM(1:4) surface finished even and smooth without using extra cement complete all as specified and directed.

Material & labour for 5 mm thick plaster in CM 1:3 on ceiling surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6 type C-2 using (40 mm graded stone agg) as in sub base Complete all as specified and directed.

M &L for Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, white tiles, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

M&L 75mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in path /plinth protection , finish even & smooth without using extra cement complete all as specified and directed.

M & L Preparation of new plastered surface of wall by applying 2mm thick wall care putty and making the surface smooth Finishing walls and applying Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)using roller for painting complete all as specified & directed.

M & L Preparation of new plastered surface of wall by applying 2mm thick wall care putty and making the surface smooth and applying two coat of oil emulsion distemper over one coat of primer using roller for painting complete all as specified & directed.

Material and labour for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified & directed.

M& L for PCC padding 1:2:4 type B1(using 20 mm graded stone aggregate) average thickness 25mm,finished fair and even without using extra cement on roof surfaces complete all as specified and directed.

M&L Rendering 20 mm thick in cement mortar 1:4 on fair faces of concrete surfaces, finished even and smooth on roof mixing with & including water proofing compound @3% cement consumed or as per manufacter's instruction complete all as specified and directed.

Material & labour for cleaning of plastered /concrete surfaces and applying priming coat using bituminous primer @ 0.30 Kg/Sqm. followed by evenly a tack coat @ 1.20 Kg/Sqm. using with 85/25 grade bitumen, over laid with 3mm thick APP modified polymeric water proofing membrane with non woven polyester reinforced of weight not less than 3.6 Kg/Sqm. unrolled and bonded to substance with side and end laps 75mm and 100mm as per manufacturer’s instructions and finished top of APP water proofing polymeric membrane with a coat of hot blown industrial bitumen 85/25 grade @ 1.20 Kg/Sqm and finally finished with a coat of bituminous aluminium paint @ 0.20 Kg/Sqm complete all as specified and directed.

Material & Labour For Powder coated anodised aluminium partition with/without sash bar, aluminium section weighing 0.55 kg/Mtr (minimum) including necessary joining cleats, Glazing clips, rubber packing aluminum snap beading, screws suitable anodised aluminium frame with one or more rebates including 5 to 6 mm thick glass all fixed to frame glass complete all as specified and directed.

Material & Labour For Powder coated anodised aluminium Door Shutter without sash bar, aluminium section weighing 0.55 kg/Mtr (minimum) including necessary joining cleats, Handles, Locking Arrangement hydraulic door closer, Glazing clips, rubber packing anodised aluminum snap beading, screws suitable anodised aluminium frame with one or more rebates including supply and fix 5 to 6 mm thick black glass all and aluminium grill fixed to frame complete all as specified and directed Make :- Hindalco/Jindal or equivalent make as specified in PS.

M&L powder coated anodised aluminium windows side Hung type with sash bars, aluminium sections weighing 0.55 Kg/mtr (minimum) incl Stainless Steel Mosquito Proof Wire Mesh Fixed With clips, frame , necessary joining cleats, glazing clips, neoprene rubber gasket with aluminium beading screws suitable anodised fittings such as hinges, handles including powder coated anodised aluminium frame, with one or more rebates including S&F 5.50 mm thick black glass complete all as specified and directed.

M&L powder coated anodised aluminium Ventilators fixed/Side Hung Type whatever required with sash bars, aluminium sections weighing 0.55 Kg/mtr (minimum) incl stainless steel mosquito proofing wire mesh fixed with , clips, frame , necessary joining cleats, glazing clips, neoprene rubber gasket with aluminium beading screws suitable anodised fittings such as hinges, handles including powder coated anodised aluminium frame, with one or more rebates including S&F 5.50 mm thick tinted pin headed glass complete all as specified and directed.

M&L preparation of new or previously untreated steel surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply & fix mild steel framed work such as grills, gratings guard bar etc with ends of bars shouldered and/ or riveted etc completed all as specified.

M&L in repair for laying 60 mm thick machine pressed precast PCC coloured interlocking paver block moulded in PVC frame / mould any shape and size conforming to IS 15658-2006 of M-35 grade of approved design with gray cement and pigment to match shade / colour / matrix of tiles set and bedded over and including 25mm thick fine river washed sand duly compacted with surface vibrator laid over compacted sub soil in flooring complete all as specified and directed.

S&F Pre-cast cement concrete block masonry 1:2:4 Type B-1 (using 20mm graded stone aggregates) with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete all as specified and directed.

Material & labour for hardcore of broken bricks gauges n.exc. 63mm, deposited spread and leveled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and directed.

Material & labour for point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi stranded, FRLS PVC insulated, unsheathed copper conductor cable in and including PVC concealed conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories / fittings, brass screws, washers etc, sunk zinc coated pressed steel terminal boxes including all cutting holes in or through walls, making good to walls, ceiling etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated stranded copper conductor cable, unsheathed and connected to common earth and earth dolly complete all as specified and directed for One light point controlled by one, one way switch 05 / 06 Amps.

All as per item No 42.00 here-in-before but One fan point controlled by one, one way switch 05 / 06 Amps.

All as per item No 42.00 here-in-before but One 3 pin, 05 / 06 Amps socket outlet point on same board controlled by one, one way 05 / 06 Amps switch.

All as per item No 42.00 here-in-before but One 3 pin, 05 / 06 Amps socket outlet point on independent board controlled by one, one way 05 / 06 Amps switch.

All as per item No 42.00 here-in-before but but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 15 / 16 Amps socket outlet point on independent board.

Supply and fix switch piano flush type, 05 / 06 Amps single pole, one way 240 volts complete all as specified & directed by Engr-in-Charge

Supply and fix socket outlet 5 pin, 05 / 06 Amps flush type 240 volts complete all as specified & directed of maby Engr-in-Charge .

Supply & fixing lamp holder (Angular / Straight), insulated body, with back plate for batten fitting complete all as specified and directed.

Supply and fix LED lamp 9/10 complete all as specified and directed.

Supply and fix LED Batten 20 Watt aluminium housing integtrated type complete with all accessories and fixing material all as specified and directed by Engr-in-Charge.

Supply and install, hi wall split units indoor and outdoor complete with cordless remote control unit and with in buit air ioniser and plasma filter for better indoor air quality with minimum 5 star rating of capacity 1.5 Ton, inverter AC having variable speed inverter compressor , copper material ,single phase 230 Volts complete all as specified and directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 140 V to 280 V with output voltage stabilized at 230 V with accuracy of 2.5% and of capacity 5 KVA complete all as specified and directed by Engr-in-charge.

Material and labour for sub main wiring with 2x4 Sqmm nominal cross sectional area (two single core cable of 4 Sqmm for Phase and neutral + o1 single core cable of 4.0 Sqmm for earth wire), 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor cable with and including continuous earth wire of size 4.0 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories / fittings, brass screws, washers etc and connected to common earth dully including all cutting / chases etc in wall and making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing Note - One meter of conduit along with 2x4.0 Sqmm wire and one 4.0 sqmm earth wire shall be measured as one length).

Supply and fixing sheet metal enclosure, Single pole and neutral AC, 240 Volts 04 way, with 200 Amps rated copper bus bar and IP - 43 & IK 09 protection including provision for four pole isolator/mcb as incomer with metal double door and flush to wall including all cutting etc on wall and making good including two coats of white / colour washing / distempering etc to match the existing disturbed surfaces and taking down the old distribution board of any type complete all as directed.

Supply & fixing industrial type SPN enclosure with a two pin and earth plug and socket complete with and including 20 Amps MCB, single pole, AC, 240 volts and flush to wall including all cuttings & chases etc on wall and making good including two coats of white / colour washing / distempering etc to match the existing disturbed surfaces complete all as directed .

S&F isolator double pole 'B' series 63A amps capacity AC 415 V,10kA complete all as specified and directed.

Supply and fixing MCB, SP, AC, 240 volts "C" curve series capacity of 06 to 32 Amps, 10kA and making connections complete all as specified & directed.

Supply and fixing LED security light fitting 1x45 Watt luminaries with die cast aluminium housing IP-66 comprising epoxy powder coated enclosed with glass coverembedded lens in frame with high power LED white lamp type of capacity 45 watt complete all as specified and directed.

Supply & fixing of ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified & directed by Engineer -in- Charge.

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 4 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as directed by Engineer - in - Charge.

Supply and fixing MCB, SP, AC, 240 volts "B" curve series capacity of 06 to 32 Amps, 10kA and making connections complete all as specified & directed.

Supply & fixing MCB, DP (Double Pole), AC, 240 volts, B series capacity32 Amps to 40 Amps 10kA and making connections complete all as specified & directed.

Supplying & laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 25 Sqmm 4 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches, fixing on wall, under road crossing through protection pipe etc complete all as specified and directed.

Supply / laying and fixing 40mm bore galvanised steel tubes with all fittings, light grade, laid in trenches for cable protection complete all as specified and directed.

M&L for washed river dry sand cushioning in trenches 80mm thick before laying the cable and 150mm thick after laying the cable including spreading levelling andhard punning complete all as specified & directed by Engr-in-Charge.

Material and labour for contineous brick of flyash designation 75kg/cm2 complete all as specified and directed.

Supplying and fixing recess mounting LED 2X2 luminaire 34/36 W CRCA powder coating housing with anti-glare diffuser new deep back lit panel metallic frame, including all acessories all as specified and directed by Engr-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fixing Vertical Loadline sheet metal enclosure double door, Triple pole and neutral (TP&N vertical loadline) AC, 415 volts, 04 way, with 200 Amps rated copper bus bar and IP - 43 & IK 09 protection, with the inbuilt provison for fixing of 1 No MCCB of XT1160 frame suitable upto 160 Amp and 12 Nos MCB'S inside of DB, including 100 Amps ,18 KA 4 pole MCCB with metal door and flush to wall including grouting and cutting in existing wall and making good disturbed surface with two coats of white / colour washing / distempering etc to match the existing one complete all as directed by Engineer - in - Charge.

Rajneesh Jain (BID ID -3098635)

M/S AGARWAL CONSTRUCTION CO. (BID ID -3099050)