PROVN OF CERTAIN MINOR AND REVENUE WORKS UNDER AGE B/R-II AND AGE E/M OF GE SOUTH DELHI CANTT-10

Amount

M&L for hardcore of gauge not exceeding 63 mm deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface for plinth protection/path complete all as specified and as directed.

M&L for 75 mm thick Cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base to floors, finished even complete all as specified and as directed.

M&Lfor 25 mm thick cement concrete 1:2:4 type B-1 (Using 20mm graded crushed stone aggregate), as in sub base in floor/paving etc complete all as specified and as directed.

M&L for Vitrified Ceramic tiles, light shade, 8-10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry @ 3.00 kg per Sqm and pointed in white or coloured cement to match the shade of tile, complete all as specified and as directed.

M&L for Vitrified Ceramic tiles, light shade,8-10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in skirting etc. over and including 10 mm thick rendering in cement mortar 1:4, set and jointed in neat cement slurry @ 3.00 kg per Sqm and pointed in white or coloured cement to match the shade of tile, complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m in depth and 1.5 m in width and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in hard/dense soil complete all as specified and as directed.

Removing excavated material (soil) not exceeding 50 m and deposited where directed at a level not exceeding 1.5m above the strating point complete all as specified and as directed.

M&L for providing cement concrete 1:4:8 type D2 (Using 40mm graded stone agg) in foundation, mass concrete and filiings complete all as specified and directed.

M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc., basement slabs, under-reamed piles and mass concrete, complete all as specified and as directed.

M&L for providing reinforcement cement concrete M-25 (Design Mix) as in columns and pillars etc complete all as specified and as directed.

M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed.

M&L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide complete all as specified and as directed.

M&L for reinforcement cement concrete M-25 (Design Mix) as in Beams, cantilevers, bressummers, lintels over 1.5m span concrete etc complete all as specified and as directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter for rough finished surface of concrete, complete all as specified and as directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions of square, rectangular or polygonal shape for fair finished surface of concrete, complete all as specified and as directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished surface of concrete, complete all as specified and as directed.

M&L for from work to soffits of suspended slabs such as roof slabs, floor slabs, landing & similar work not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces, complete all as specified and as directed.

M&L for mild steel TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including muld seel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

All as per item no 19.00 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, complete all as specified and as directed.

M&L for roof treatment in following stages, complete all as specified and directed by engineer-in-charge. (i) Preparation of concrete surfaces by wire brush and cleaned top surfaces of cement concrete . (ii) APP polymeric water proofing membrane minimum 3 mm thick and wieghing not less than 3.5 Kg per Sqm , black finish reinforced with non woven polyester matt with a thermo fasable finish laid over bitumen primer @ 0.5Kg/Sqm by torching application with a propane or a butrane gas torch with an overlap of 100mm at the sides and 150 mm at the ends, as per manufacturers instruction including applying two coats of aluminium paint over APP membrane (Manufacturer as approved by GE).

M&L for anti termite treatment of soil ,treating the top surface of earth at the rate of 5 litres of emulsion per square metre of surface, complete all as specified and as directed.

Material & labour for brick work with sub class B old size burnt bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specifie and as directed.

Material & labour for brick work with sub class B old size burnt bricks straight or curved on plan to any radius in walls built in cement mortar 1:4 in half brick thick complete all as specifie and as directed.

M&L for 15 mm thick rendering with ready mix plaster on faces of brick or concrete wall surface, finished even and smooth complete all as specified and as directed.

M&L for 10 mm thick rendering with ready mix plaster on faces of brick or concrete wall/ceiling surface, finished even and smooth complete all as specified and as directed.

Supply only Liquid water proofing compound of approved quality, complete all as specified and as directed.

M & L for preparation of the newly plastered surfaces of walls/ ceiling and applying two coats of GreenPro certified water-based, modified acrylic, exterior Apex Suprema Emulsion or equivalent as per required shade (Company depot tinted) with silicon additives, heat reflectant property, VOC less than 2% by mass, Class A IS-15489 and IS-101 @5-6 sqm/ltr over one coat of primer with and including 1mm thick water proof cement base wall care putty to prepare the surface even and smooth complete all as specified and as directed.

M & L for prepartion of newly plastered wall/ceiling surface and applying two coats of distemper oil emulsion, with spray machine on wal/ceiling surface white or tinted over one coat of primer with and including 1mm thick wall cement base care putty to prepare the surface even and smooth complete all as specified and as directed.

M & L for preparation of newly plastered surface of walls and apply three coats of white wash complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate), as in floor/paving with PVC/glass/marble strips etc complete all as specified and as directed.

M&L for 50 mm thick sand cushioning for laying of floor finishes/interlocking paver lock complete all as specified and as directed.

M&L for framed work such as grills, gratings, angle, square hollow pipe etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; tracking for steel gates, sheet framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 complete all as specified and as directed.

S&F mild steel Z type ventilator with guard bars and jali frame installing in brick wall , fixed with cement concrete 1:2:4 (12.mm aggregate ) bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers , and similar small articles conforming to fe290 Gde E-165 complete all as specified and as directed.

M&L for poweder coated (powder coatiing not less than 50 micron) aluminium anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5mm thickness (section no. 20831 of JINDAL) and of shutter size 40 mm x 18 (with 9.00 mm interlocking legs) x 1.45 mm thick (section no. 20737 of JINDAL) section (two shutter glazed, covering half of span of opening each & one shutter sketlon covering half of span of opening) including provn for making windows air tight, including 95 mm aluminium handle with spring lock, stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4 mm and fixed with steel wire stapples and 5 mm thick plain glass including necessary fitting/ fixture/ aluminium snap beads complete all as specified. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285,fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete all as specified and as directed.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors,windows& ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws complete all as specified and as directed.

S&F ACP sheet 4 mm thick of any colour, fixed with aluminium beading in aluminium window/ventilation etc all as specified and directed.

S&F 6 mm dia powder coated aluminium decco grill, (minimum thickness of powder coating 50 micron), section No-104, 100 mm aparture of hexagonal design and pattern as approved complete all as specified and as directed.

S&F for Mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screws confirming to Fe.290.Gde-E-165 complete all as specified.

S&F stainless steel AISI 304 grade barrel tower bolt 200mm long, extruded section,etc. complete all as specified and as directed.

S&F stainless steel AISI 304 grade handle of size 200mm long,etc. complete all as specified and as directed.

S&F Stainless steel of AISI 304 Grade, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F Floor door stopper (double leg) of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 60mm complete all as specified and as directed.

M&L for 18 mm thick wood plastic composites (WPC) board, 100% solid with density not less than 650 Kg per cubic meter , one side wood grain finished laminated for exposed/external surface , fixed with screws fitted under or above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc complete all as specified and directed. Note : (a) Pattern & design of WPC board to be decided by GE. (b) Items like cupboard knobs, stainless steel channel, CP plate clip hinges to be paid in extra.

S&F of Stainless Steel Crockery/thali basket of suitable size made of high quality (SS-304) 6 mm dia wire mesh with smooth edge, suitable for modular kitchen drawer unit including heavy duty telescopic channels, complete all as specified and as directed.

S & F Continuous (piano) hinges width of flap 30 mm, mild steel, bright finish or electrogalvanised fixed to steel chowkhat with welding or with screws complete all as specified and as directed.

S&F 15mm mild steel, chromium plated rod with fixing brackets, fixed in cupboards for hanging cloth of adequate strength complete all as specified and as directed.

S&F stainless steel AISI 304 grade handle of size 75 mm long,etc. complete all as specified and as directed.

S&F Magnetic catch for wooden cupbord with complete closer macanigum claps and clips fix with stainless steel screw complete all as specified and as directed.

S&F Powder coated anodised aluminium snap grid frame size 605 x 605 mm and 2-3 mm thick for false ceiling, hangers 6 mm dia. G.I. (upto1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm longand expansion hold fasteners 12.5mm dia. 40mm long and including acoustic gypsum perforated tiles 4 mm thick of size 600x600 mm fixed in ceiling or laid/ inserted to Aluminium snap grid complete all as specified and as directed.

M&L for Chequered cement concrete tiles with grey cement and pigment 25 cm x 25cm x 25 mm thick set & jointed and pointed in cement slurry to match over and including 15mm thk screed bed in cement mortar 1:6 on plinth laid over and including 50 mm thick cement concrete 1:3:6 type C-2 using 20 mm graded crushed stone aggregate as in plinth protection, laid to slope of 1 in 24 in alternate basis system, without , each bay shall not exceed 3m in length, 12mm wide joint & 50mm deep joint shall be formed between the bays which shall be filled with Mastic filling to full depth comprising a mixture of 1 part of heater hot blow bitumen 85/25 portion and two parts of heated Badarpur sand (by volume), complete all as specified and as directed.

S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 65x 125 mm 2 or more rabates comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed. Note: For WPC solid door/windows frames,minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed.

Surface dressing not exceeding 15 cm deep in any type of soil complete all as specified and as directed.

M&L for 100 mm thick cement concrete (1:4:8) Type D-2, (40 mm graded crushed stone aggregate), as in sub-base of floor and similar works complete all as specified and as directed.

M&L for cement concrete type B-1, 1:2:4 using 20 mm graded stone aggregate as in holdfasts, coping on edges etc including weathering slightly rounded or chamfered angles and throating as directed including necessary formwork complete all as specified and as directed.

M&L for 60 mm thickness, M-35 grade machine pressed precast concrete interlocking paver block of any colour, any shape and size confirming to IS 15658-2006, laid over and including 50 mm laid sand cusioning complete all as specified and as directed.

Excavation in post holes in hard / dense soils , each not exceeding 0.50 cum, getting out, returning filling in and ramming earth in layers not exceeding 25 cm including watering & removing surplus soil to a distance not exc. 50m & making good surface complete all as specified and as directed

Cutting holes in brick walls in built in cement mortar or cement lime mortar exc half brick but not exc one brick complete alll as specified and as directed.

Cutting chases ,pinning in , making good to facings where required and pointing in cement mortar 1:3 to ends or edges or landings, steps, cills, sunshades,shelves,lintel,etc and cutting in chases for concealed conduit wiring, etc and making good, cutting not exceeding 10 cm girth complete alll as specified and as directed.

M&L for mild steel work in tubular trusses including special shaped washer, cleats etc complete using ERW or induction butt welded tubes confirming to IS: 1161-1979 grade st - 240 complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description , not itherwise described , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zink chrome primer including, complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh size and type and type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and as directed.

Supply only MS galvanished chain link fencing with 3 mm dia and size 50 mm x 50 mm including line wires including strain bolts, binding wire etc all as directed.

S&F mild steel screw bolts (machine made) with hexagonal head at one end and screwed the other or screwed both ends each screwed and to be fitted with washers and with hexagonal nut of exc 5 cm length with dia of shanis 11 to 15 mm etc complete all as specified and as directed.

S&F mild steel work such as in fencing post, tie bars etc including embedding into concrete and making holes for screwing of nut, bolts, cutting top to shape as directed, drilling holes, notching for wire etc confirming Fe 290 Gde E-165 complete all as specified and as directed.

M&L for mild steel for framed work as in doors, gates of angle or section with gusset plates complete drilled or welded to be prepared for hanging or sliding with and including either hooks and hinges etc confirming Fe-410-W (Gde-E-250) quality-A complete all as specified and directed.

S&F 4 mm thick fibre glass reinforced translucent plain sheeting of any colour and pattern fixed with coach screw and washer in wall , complete as specifed and as directed.

M&L for Rolled mild steel in Joist, channel, angle, or tee sections fixed independently, without connecting plates , Fe -290 (Gde E-165 ) complete all as specified and as directed.

innovision limited (BID ID -3392036)

Ex Serviceman Enterprises (BID ID -3400649)

P R Constructions (BID ID -3400441)

M/S Parmod Johar (BID ID -3392336)

H S KALSI AND BROS (BID ID -3395962)

M/S HARINDER SINGH (BID ID -3389174)