MCM/EE-II/2021/233 Reffer to DNIT

Amount

-Providing and fixing Antoskid, Pre-polished cement concrete designer tiles to also be laid at provision for physical challenged as approved buy the Engineer-in charge .These should be cleanable acid resistant and fixed without grove and grout and should look like joint less as per manufacturer instructions laid over bad of 25mm thick cement mortar 1:3 (1 cement : 3 coares sand) complete as directed by Engineer-in-charge.

-Providing and pasting at site high grade printed vinyl with bus shelter name logo, route number etc. On one sides of the front facia information board.The vinyl shall be minimum 85 micron thick, of LG or equivalent make complete in all respect and to the entire satisfaction of Engineer-in-charge.

-Providing and fixing anodized aluminum 25x50mm channel frame with 40W standard manufactured tube light fittings with electronic chock starters and wiring all complete connection to electrical supply drom feeder box with minimum 4 tubelights x per square meter (of add panel size) or actual requirement decided by the engineer in charge. The tube light frame and fittings (including that infeeder pillar) should include ballast ELCB timer MCB mounting blocks etc. the tube light alignment should allow two way lighting (front and back) off add panel .

-Providing and fixing MS Electrical weather proof feader box approximately 600mm wide and 900mm high as required for installing MCB switch gear and meters as required for advertisement and other electrical gear, with provision for inserting cable condails as per design.The access to feeder box shall be through a toll based (common for all locks provided in each package) key, Tolls should not be identical for different package shelters.

-Supplying and fixing single sides aluminum frame signage made of 6063-T5 alumium frame with section weight 3.80 to 4.00kg/m with minimum tensile strength 22000 psi as per drawing provided having 4mm clear soild compact polycarbonate in front and 3mm ACP sheet rainforced with inernal support frame at rear completely sealed with the of silicon and EPDM to make it dust and water proof should have the inbuilt strong clipping and frame arrangement for holding the flex or digital media alongwith all necessary cleats and corner joinery required to build thus signage with sufficient strength. The aluminum frame should have strong locking arrangement which can resist theft. The aluminum frame should have polyester powder coating with minimum thickness of 60 micron. Signage should have inbuilt arrangement of mounting it with the bus shelter structure. The enclosure should provide weather proof protection required for the signage to operate outdoors, having inbuilt ventilation systems.

-Providing and fixing medium grade MS junction boxes in cast in situ foundstion beam of 150x150mm size.

-Vandal resistant light source of polycarbonate body with compact fluorescent lamp with white colour of 55w of standard, MY 1: of approved make with IP 67 approval, including cable fixing, switchgear etc.all complete.

-Providing and fixing various member of material shall be austenitic steel of the grade 1.4301 (widely known as 304) it shall contain 17-18% chrormium and 8-11% nickel as per satisfaction of the Engineer n charge. (DSR 10.28)

-Supply and erection of PVC copper insulated and sheathed 2 core circular flexible wire complete as per HSR. (A) 2x2sq.mm

-Supplying and fixing of double sided aluminum frame signage made of 6063-T5 aluminum frame with section weight 5.3 to 5.5kg/m with minimum tensile strength 22000 psi as per psi as per drawing provided having 4mm clear soild compact polycarbonate on both side and rainforced with internal support frame completely sealed with the help of silicon and EPDM to make it dust and water proof. Should have the inbuilt STRONG clipping and frame arrangement for holding the flex or digital media alongwith all necessary cleats and corner joinery required to build thus signage with sufficient strength. The aluminum frame should have strong locking arrangement which can resist theft. The aluminum frame should have polyester powder coating with minimum thickness of 60 micron. Signage should have inbuilt arrangement of mounting it with the bus shelter structure. The enclosure should provide weather proof protection required for the signage to operate outdoors, having inbuilt ventilation systems.(measurements for double sides signage to be taken for both sides during billing)

-Earthing with GI earth pipe

-Provoding and fixing 10mm thick polycarbonate multiwall sheet broze colour having a light transmission of 37% with a U-value of 2.39 w/m2 K.Lexan thermoclear multiwall sheet LT2UV105R175 from SABIC innovative plastics or Equivalent. Fixing of the 10mm sheet to be done with profiles having EPDM/silicon. Aluminium profiles need to use and front and rear of polycarbonate sheet has to be closed by alumium profile.

-Supply and erection of PVC copper insulated and sheathed 2 core circular flexible wie complete as per HSR. (A) 1x0.75sq.mm

Bidder Name

Amount

McCROMIK Industries(GSTN-06AQGPP0869A1Z0)