SPL REP TO BLDG NO T-18 (TOILET BLOCK) AT NAYA RAIPUR MIL STN UNDER AGE (I) NAYA RAIPUR

Amount

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressedstonework and precast concrete articles

M&L cement concrete 1:5:10 type E2 (using 40mm graded stone aggregate) in foundation all as specified and directed .

Cement concrete 1:2:4 type B0 using 12.50mm graded stone aggregate in floors, 25mm thick, for base of tiles cement complete.

M&L 15mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and directed.

M&L Non skid ceremic coloured tiles of area of each tile exc 0.06 not exc 0.11 sqm and 7 to 8 mm thick joint free as in floor set and jointed by neat cement slurry and painted in white cement with pigment to match the surface of tiles complete all as specified and directed.

Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) - 75mm thick

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete.

M & L Rolled mild steel sections conforming to Gde Fe-410-0 or Fe-310-0 as in framing for cladding, glazing and the like including door frames/chowkats, fixed with angle cleats and connecting plates, etc complete.

Fabrication and Fixing onlyRolled mild steel sections conforming to Gde Fe-410-0 or Fe-310-0 as in framing for cladding, glazing and the like including door frames/chowkats, fixed with angle cleats and connecting plates, etc complete.

S&F 3mm.thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.5 Sqm in each pane complete all as directed at site

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete.

S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube S&F in opening all as shown on drawing and specified.

S&F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheets strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side and as gap inside for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/seated to the stiles and rail with suitable PVC sheet bending and jointed to gather with solvent cement supplying and fixing in the frame at site as per specification and drawing

M&L two coat of synthetic enamel paint on steel surfaces of any description not otherwise described over 10cm width or girth including preparation of old surfacesand apply a coat of red oxide primer complete and all as specified and directed

S&F MS 100 mm size butt hinges medium wt. of cold rolled complete and all as specified and directed

Aluminium anodised, barrel tower bolts of extruded section and fixed - Length of bolt - 150mm

Aluminium handles, cast type, anodised - S & F - Size of handle 150mm

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed - Length of bolt - 300mm

S&F in repair Vitreous china wash basin, white, flat back, size 550 x 400mm, including brackets and cutting for and pinning in ends of brackets, complete.

S&F in repair for 10ltrs capacity flushing cistern PVC low level valve less, symphonic action type flushing cistern white with inlet, ball valve, float and handle including brackets and 32 mm flush pipe of polyethylene complete all as specified and directed.

S&F vitreous china squatting pan ORRISA Pattern of size 580x 440mm white with integral foot rest and 's'or 'p trap'complete (excluding cistern and flush pipe) with provn of lime concrete including backing joints all as directed at site.

PVC(SWR) floor trap with grating including jointing to waste pipe in solvent cement, dia of outlet75 mm complete.

PVC (SWR) bends (any radius), (larger bore measured) 75 mm bore with cement joints complete.

PVC (SWR) bends (any radius), (larger bore measured) 110 mm bore with cement joints complete.

S & F PVC single socketed soil, waste and vent pipes, in any length with rubber ring, laid in trenches or in floors, _75 mm bore complete.

S & F PVC (SWR) pipes single socketed, in any length with rubber ring joints,fix to wall - Bore 75mm.

PVC single socketed soil, waste and vent pipes, in any length with rubber ring, laid in trenches or in floors, 110 mm bore complete.

PVC (SWR) junction single, (Single T) equal or unequal - Bore 75mm - S & F

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls - Bore 110 mm - S & F

PVC cowls,110_mm bore with cement joints complete

Taking up or down 15 mm dia steel tubing and connection including removal complete and all as specified and directed

Taking up or down 20 mm dia steel tubing and connection including removal complete and all as specified and directed

Taking up or down 25 to 32 mm dia steel tubing and connection including removal complete and all as specified and directed

S&F15mm bore steel tubes medium grade galvanized with all fitting and fixed complete to walls and ceiling or lay in floor complete and all as specified and directed

Refixing old steel tubing and connections15 mm bore, in new or old position (walls, ceiling, floors, etc) complete.

S&F20mm bore steel tubes medium grade galvanized with all fitting and fixed complete to walls and ceiling or lay in floor complete and all as specified and directed

Refixing old steel tubing and connections 20 mm bore, in new or old position (walls, ceiling, floors, etc) complete.

S&F25mm bore steel tubes medium grade galvanized with all fitting and fixed complete to walls and ceiling or lay in floor complete and all as specified and directed

Refixing old steel tubing and connections25 mm bore, in new or old position (walls, ceiling, floors, etc) complete.

S&F in repair bib taps cast copper alloy with crutch or butter fly handle screwed down screwed for iron pipe 15mm bore complete and all as specified and directed

S&F 1000 ltr capacity Rotational moulded polyethylene water storage tank (cylindrical vertical closed top) hoisted and fixed in positions all as specified in SSR Part-I,including 20 mm dia of ball valves high pressure of PTMT with epoxy coated aluminium rod &highdensity plastic ball screwed for iron pipe and fixed

Gun-metal, globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe and fixed.

Gun-metal, globe or gate valves 25mm, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F15mm bore PVC connection 300mm long with PTMT nut complete and all as specified and directed

S&F in repair 15 mm bore pillar tap cast copper alloy with capstan head chromium plated complete and all as specified and directed

M&L brick work with fly ash brick modular size in cement mortar 1:6 straight or curved on plan exc. 6m mean radius complete and all as specified and directed

Brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in Modular bricks in cement mortar 1:6

M & L 15mm thick plastering on fair faces of brick wall in CM (1:4) surface finished, even and fair without using extra cement

M&L 3 coats of white wash after preparation of new surfaces of walls complete and all as specified and directed

M&L precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 complete

Mild steel TMT bars 6 to 8mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete.

Cutting into existing manholes for connecting new drains, 150 mm bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required complete.

5mm thick Prelam PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site - S & F

5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.- S & F

Excavation in trenches n exc. 1.5 m wide and n exc. 1.5 m in depth for foundation etc in soft/loose soil and getting out complete all as specified and directed

Removal of surplus soil to a distance n. exc. 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete

Dismantling wall and ceiling boards or insulation boards, any thickness, any description, including cover fillets complete.

Refixing OLD 'E' board (after proper cleaning) 4 mm thick white fixed at all height laid on pre fix hot dipped galvanised iron imposed grid all as per manufacturer's instructions complete all as directed.

Supply & fixing 'E' board (Everest make) 605 x 605 x 4 mm thick white prelaminated set & embosed, reinforced, designer ceiling board tiles of approved texture fixed at all height laid on hot dipped galvanised iron imposed grid with 24 mm wide T-section exposed flanges which shall be powder coated, white,.the frame work shall comprises of main runner made from 0.33 mm thick galvanised steel sheet and of size 24 x 32 x 300 mm and spaced at 1200 mm center to center fixed to be structural soffits by approved hangers at 1200 mm rawl center, hangers of GI wire 4 mm dia to be fixed by approved rawl plug, level and fasteners and screws etc., the last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall, flush fitting of 120 mm long cross tee (with double stiching) to be interlocked between main runners at 600 mm center to center, size 1200 x 600 mm modules, cross tee longer than 600 mm to be supported independently on 600 x 600 mm moduler to be formed by fitting 600 mm long cross tee centrally between the 1200 mm cross tee. Tee, perimeter wall angle shall be of 0.45 mm thick GS sheet of size 19 x 19 mm and 300 mm long of white colour all as per manufacturer's instructions complete all as directed.

S&F in repair angle valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, screwed both ends for iron pipe or for unions 15mm bore, complete.

S&F soap dish chromium plated complete and all as specified and directed

S&F towel ring chromium plated complete and all as specified and directed

Taking down carefully copper/Aluminum point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, pendants, regulators sockets etc. and making good the disturbed surfaces of walls, floors etc and match with the existing colour of wall complete all as specified and as directed.

Taking down carefully by unscrewing from board/out-let boxes, light fitting, fixture and fittings such as MCB DB with MCB, wooden board, sheet metal enclosure with plug top and MCB etc. complete all as specified and as directed.

M&L Point wiring complete with 1.5 sqmm PVC insulated stranded copper conductor single core cable drawn through and including rigid non metalic PVC conduit 20 mm dia ( meadium grade ) , ISI marked with concealed conduit wiring including cutting chases and making good in CM 1:3 & white/colour wash to match existing surface, pressed steel terminal boxes not less than 1.6 mm thick concealed in wall duly painted with two coat of black bituminous paint over a coat of red oxide primer, plastic laminated top sheet cover 2.8 mm thick of required size and colour for housing switches and sockets, 1.5 sqmm PVC insulated (green insulation) copper conductor as earth continuity cable drawn with wiring and connected to common earth dolly all as specified for -

(a) One light point controlled by one switch

(b) One Fan point controlled by one switch

(c) One socket out let 5 pin 5 Amp on same board

All as per item No 03 above but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed cable for 3/6 pin 5 & 15 Amp socket outlet controlled by one switch on independent board with and including 1.5 sqmm green stranded copper conductor as continuous earth wire with lugs complete all as specified and as directed.

S&F Switch piano flush type polycarbonate , Single pole, one way, 6 amps, 230 Volts, specified make

S&F socketoutlet 2in 1-5 pin , Single pole,polycarbonet one way, 6 amps, 230 Volts, specified make

S&F socket outlet 2 in 1 5 pin combination polycarbonet, Single pole, one way, 16 amps, 230 Volts, specified make

S/F Ceiling rose surface type bakelite, two or three terminal

S & F MCB DB epoxy powder coated distribution box SPN, 8 ways, 240 volts, for MCB double door , grouted flush to walls with IP 43 and metal door complete all as specified and directed.

S & F SP, 6 to 32 Amps, 240 Volts , 10 KA , 'c' curve MCBs complete all as specified and directed :- (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S & F SPN, 32 Amps, 240 Volts , 10 KA , 'c' curve MCBs complete all as specified and directed :- (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

Supply and fixing Wall mounting indoor decorativeLED T-8 batten with opel diffuser 1x 18 W LED tub light mounting over two nos of round wooden blocks complete with , tube and all accessories making electrical connections with twin core PVC flexible copper wire of size 0.50 sqmm upto 1.5 mtr length complete. Make - Philips/Wipro / Oshram

Supply & Fixing exhaust fan 300mm sweep PVC type 240 volts complete all as specified and directed. Make Orient/USHA/CG

Supply and fix recess mounted ceiling light 11 watt any type with all fixing arrangement ,all as per required and directed by engg in chrge Make Wipro Cat No LD91-141-XXX-65-XX or equivalent in Philips /Oshram

Supply and fix building security light of 18watt IP 65 watt,LED die casting aluminium with LED street optic lenses ,efficacy of skyline plus is upto 120lm/w, with pea nut lenses LED type with bracket arrangement all as per required and directed by Engg in Chrge MAke - Wipro Cat No LR13-241-XXX-57-XX or equivalent in Philips/Oshram

Supply/Laying or fixing or passing through pipe, jointing and testing 1100 volt grade XLPE insulated armoured heavy duty PVC insulated, PVC sheathed armoured electric cables with aluminum stranded conductor, 16 sqmm 2 core complete all as specified and as directed.

All as per item no 16 but of cable size 6 sqmm 2 core flexible

Excavation in trenches in any type of soil not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth and getting out for laying of pipe cables etc,. and getting out complete all as specified and directed

Returing filling in, including spreading levelling, watering and well ramming in layers not exceeding 25cm thick with earth obtained from excavation complete all as specified and as directed.

Removing excavated soil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

Material and labour for dry river washed and screened dry sand for filling in trenches below and around the cable for cushioning including punning down as specified in relevant clause of SSR Part I. Note:- Punned thickness shall only be measured and paid.

Supply and lay bricks sub class 'B' laid dry abutting each other with gap between adjacent slab not exceeding 10mm over UG cable as in cable protection all as directed.

Material and labour for PCC 1:2:4, type B1 using 20 mm graded stone aggregate as in coping, mud stops, benching, etc. on around poles, chajjas and weathering, slightly rounded or chamfered angles, throating etc. including necessary form work complete as all specified and as directed.

Material and labour for earthing complete with galvanised steel plate earth electrode 600 X 600 X 6mm thick buried directly in ground (earth pit not less than 2.25 meter below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected with 4 mm galvanised steel wire at two points by means of bolts and nut, check nut and washers including charcoal dust, common salt, necessary excavation in hard/ dense soil, returning filling in and removal of surplus soil to a distance up to 50metres, PCC pit in 1:3:6, type C-I, using 20mm grade stone aggregate and MS angle iron frame 40 x 40 x 6mm, RCC 1:2:4, type B-1, using 20mm grade stone aggregate, 50mm thick pit cover, reinforced with 8mm dia TMT bars, 75mm centre to centre both ways, MS handle 12mm dia, PGI funnel, wire mesh and GI pipe of 20mm bore (light grade) and earth lead protection pipe 15mm bore (light grade) and all as shown in electrical plate No. 3 of SSR Part-I including testing complete all as specified and directed. Note:- GI wire and protection pipe up to 7.5 metre beyond the earth plate electrode is included in unit rate quoted.

Total contracts sum shall be calculated after deduction of schedule of credit amount of Rs. 10,750.00

ashish shrivastava

FIRST SOLAR