Purchase of Equipments ( S.No 1 to s.No 5 ) for ECE Department

DSO (Digital Storage Oscilloscope) • Bandwidth: 50–100 MHz. • Sampling rate: 1 GS/s. • Channels: 2 (minimum). • Power supply: 100–240 V ac, 50–60 Hz. • Automatic measurements: Vpp, Vavg, Vrms, frequency, period, Vmax, Vmin, rise time, fall time, +width, –width, +duty, –duty, etc. • Horizontal scale: 5 ns/div – 50 s/div or equivalent. • Vertical resolution: 8 bits (2 channelssimultaneously). • Vertical sensitivity: 1 mV/div – 10 V/div (at input). • Waveform math: +, –, ×, ÷, invert, FFT, etc. • Waveform storage: 16 waveforms or equivalent. • Communication interface: USB host and USB interface. • Display: 7-inch color display or equivalent. • Input impedance: 1 MΩ ±2% || 20 pF. • Accessories: 2 × passive probes (1X/10X)

8051 MICRO CONTROLLER KIT • Operating voltage: +5 V dc. • Flash memory: 4 kB (AT89C51) / 8 kB (AT89S52). • RAM: 128 bytes internal RAM. • 16 × 2 alphanumeric LCD display. • Push buttons / tactile switches. • DIP switches for digital input. • Inbuilt ADC interface: LDR, potentiometer. • Inbuilt DAC interface. • Inbuilt stepper motor driver with stepper motor. • Inbuilt DC motor driver with DC motor. • 1 × 4 LED array, 1 × 4 keypad, 1 × relay. • 1 × buzzer, 16 × 2 LCD display, 1 × PWM driver. • 1 × hardware interrupt key, inbuilt RTC. • Inbuilt EEPROM and UART module. • 4 × 7-segment display. • Supports both Assembly and C language programming. • PC interfaceable.

EMBEDDED TRAINER KIT (USING LPC 2148) • CPU - LPC2148, Core - 16/32 bit ARM7TDMI-S • Speed - Max 60 MHz, Flash - 512KB, RAM (on- chip) – 40kB, 46 General Purpose I/OPins, USB2.0 • One 10bit A/D Converter with 14 Analog inputs, One 10bit D/A Converter, Six PWM & Watchdog • Two UARTS (16c550), Two I2C (400Kb/s), Two SPI • Eight Bit Digital Output, Eight Bit Digital Input,16x2 Characters LCD and 4x4 matrixkeypad • One potentiometer for giving analog input, Relay & Buzzer Interface • I2C Devices: RTC, EEPROM and Seven segment Display, On Board Stepper MotorDriver • LM35 Temperature Sensor, One RS 232 Lines are • Terminated at 9 Pin D type connector and USB interface • Board has inbuilt power supply and mounted in sturdy cabinet Accessories • USB cable with utility software to download programs from PC to target board • Power Cord, User Manual

STRAIN GUAGE TRAINER KIT • AC mains power supply: 230 V ±10%, 50 Hz • Metal foil strain gauge mounted on beam/cantilever. • Strain measurement under applied load. • Wheatstone bridge arrangement. • Signal conditioning and amplification circuit. • Instrumentation amplifiers with 3½ digit display for strain / output voltage. • Zero and gain adjustment controls. • Provision for applying calibrated loads. • Table-top trainer with labelled panel. • Test points for signal measurement. • Built-in DC power supplies and wooden closed cabinet. • Supplied with patch cords and User manual.

SIM READER TRAINER KIT Power Supply: • Operates on 230 V ac ±10%, 50 Hz mains supply. • Built-in regulated SMPS power supply. • Operating DC supply: 5 V / 12 V with overload and short-circuit protection. SIM Card Interface: • Supports GSM SIM cards compatible with 2G / 3G / 4G / 5G networks. • SIM card read/write interface. • Supports SIM card initialization, authentication, and communication functions. • Compatible with standard 6-pin / 8-pin SIM card sockets.Communication Interface: • USB 2.0 interface for PC communication. • RS-232 serial communication interface. • UART communication facility for embedded system interfacing. SIM Operating Parameters: • Selectable SIM clock frequencies: • 3.579 MHz • 7.159 MHz • 14.318 MHz • SIM supply voltage selection facility. • SIM reset and activation control. Supported Protocols and Standards: • GSM ETSI 07.07 and ETSI 07.05 AT command support. • ISO/IEC 7816 smart card communication support. • SIM communication command monitoring facility. Hardware Features: • On-board SIM card socket. • LED indication for: • Power status • SIM detection • Reset activity • Data transmission/reception • Built-in keypad for standalone operation. • LCD display module (128 × 64) for menu and status display. • On-board microcontroller-based control section. Software Support: • AT command execution and monitoring software. • SIM manager utility software. • Data logging and communication terminal utility. • PC-based GUI software for SIM data communication experiments. Trainer Features: • Fault simulation facility for troubleshooting experiments. • Simulation of faults such as: • SIM not detected • Clock failure • VCC failure • Reset failure • Multiple on-board test points for signal observation. • Test points for: • SIM_RST • SIM_CLK • SIM_IO • VCC • UART TX/RX • Suitable for CRO/DSO signal monitoring. • Glass epoxy PCB with educational block diagram layout. • Compact tabletop enclosed cabinet design. Construction: • Front panel with printed block diagram. • Banana test points and patching facility. Standard Accessories: • GSM SIM trainer unit. • USB communication cable. • RS-232 communication cable. • Power cord.12 • User manual. • Utility software CD / downloadable software package.