Construction of building for Bio Chemistry P.G. Laboratories

Amount

Clearing jungle including up rooting of rank vegetation grass bush wood trees and sapling of girth upto 30 cm. measured at a height of 1 m above ground level & removal of rubbish upto a distance of 50 mt. outside the periphery of the area cleared. (if however, only grass is met with the area will be measured and paid for under item 4001).

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead upto 50 m and lift upto 1.5m disposed earth to be leveled and neatly dressed including providing barricading, danger lighting guarding as directed in :

b) All types of Ordinary rock including all types of laterite rock, blasting prohibited

Earthwork in excavation by mechanical means ( hydraulic excavator/manual means in foundation trenches drain ( not exceeding 1.5 m in width or 10 sq.m on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m.

b. All types of ordinary rock including all types of laterite rock, blasting prohibited.

Extra for additional depth of 1.5 m or part thereof in:

c) All types of laterite rocks and hard rocks

Refilling the foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50M and all lifts and disposal of surplus earth as directed by Engineer in charge

Supplying and filling in plinth under floors, trenches including watering ramming consolidating, dressing, complete.

b) Moorum

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Pre-cast cement concrete solid blocks masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 corase sand ) in partitionwalls size of blocks (30 x 20 x 10)

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1:4 ( 1cement : 4 coarse sand ) in foundation and basement

Pre-cast cement concrete solid block masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 corase sand ) in all sizes in superstructure from floor one level upto floor V level ( size of block 30x23x15)

Providing and laying cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded granitic or basaltic stone aggregate 20mm nominal size ) excluding cost of centering, shuttering and finishing in :

a)all works up to plinth level

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in:

A) all works up to plinth level

Providing and laying cement concrete1:5:10 (1 cement: coarse sand: 10 graded stone aggregate 40 mm nominal size) all round S.W pipes including bed concrete 15 cm thick as per standard design.

b) 150 mm diameter S.W pipe

Providing & laying damp proof course 50 mmthick with cement concrete 1:2:4 (1 cement: 2coarse sand: 4 graded stone agg. 20 mm nominalsize).

Providing and laying in position machinebatched concrete (BMC), machine mixed anmachine vibrated design mix cement concrete ofspecified grade for reinforced cement concretework including pumping of concrete to the siteof laying but excluding the cost of centering ,shuttering, finishing and reinforcementincluding admixtures in recommendedproportions as per IS 9103 to accelerate, retardsetting of concrete, improve workability withoutimpairing the strength and durability as per thedirection of the Engineer-in-charge. M-30 gradeof reinforced cement conrete by using 420 kg ofcement per cu.m. of concrete. All works upto floor V level.

Providing and laying in position ready mixedconcrete (RMC) with usage of OrdinaryPortland Cement manufactured in fully automatic batching plant and transported to siteof work in transit mixer for a lead upto 10kmshaving continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering,shuttering, finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without imparing strength and durability as per the directions of the engineerin- charge. All works upto floor V level

v)M-30grade of concrete

Extra for carriage of R.M.C. beyond the initial lead of 10 kms.

Centering and shuttering including strutting , propping & removal of forms for

I) Foundations, Footings, Bases for columns

II)Vertical surfaces such as retaing walls, returnwalls, Partitions, walls (any thickness) includingattached Pilasters, Buttresses, Plinth and stringcourses, Fillets and the like

III) Columns , piers, pillars, abutments, posts and struts ( square, rectangle or polygon in plan )

iv) sides / soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels plinth beams not exceeding 1M in depth

XIII) Suspended floors , roof landings, shelves & their supports,chajjas

vi) Staircases ( except spiral staircases) excluding landing

xiv) Vertical or horizontal fins individually formingbox louvers or projected bands

Centering & shuttering including Strutting,Propping & removal of forms for sloping orbattering surface (slabs, beams, louvers, etc)including folded plates

(iii) Columns, Pillars, Posts & struts (circular orcurved in plan)

Extra to be added for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and de centering at all levels, over a height of 3.5 m for every additional height of 1m or part thereof ( Plan area to be measured)suspended floors, roofs, landings, beams and balconies( plan area to be measured)

Providing corrosion resistant steel CRS-50 bars of (SAIL, TATA, VIZAG, JSW SteelLtd.)(Confirming to IS 1786 if 1985) for RCCwork including bending, binding & placing inposition in all the floors along with factory made precaste concrete cover blocks of specified s izeswhose compressive strengthis not less than thatof surrounding concrete in the structuralmember .

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer : Flamed finish granite stone slab.

a) Jet Black

Providing and fixing Granite stone slabs (flamed finish) 18mm thick in risers of steps, skirting, dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

a) Jet Black

Providing and fixing Granite stone slabs (mirrorpolished) 18mm thick in risers of steps, skirting,dado and pillars laid on cement paste andjointed with grey cement slurry mixed withpigment to match the shade of the slabs,including rubbing and polishing complete

a) Jet black

Providing and fixing vitrified matt finished (600 X 600) and 10 mm thick tiles in floor, treads of steps, and landings on 25 mm thick cement mortar 1:3 and jointed with cement slurry complete(Johnson, somany ,kajaria).

Providing and fixing Vitrified tiles in different sizes (thickness to be specified bymanufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps and dados, jointing with grey cement slurry @3.3 kg per sqm, including pointing/grouting in white cement mixed with pigment of matching shade complete

600 x 600 mm - Light Shades

Providing and and laying vitrified unglazedorcelain tactile floor tiles in different sizes ofJohnson, Somany, Kajaria (thickness to bespecified by the manufacturer) and conformingto IS:15622 of approved make in colours andshades as specified laid on 20 mm thick cementmortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement andmatching pigment etc., complete

a 300 x 300 mm Design - Liner

b 300 x 300 mm Design - Buttons

Providing and fixing vitrified matt finished (600 X 600) and 10 mm thick tiles in floor , treads of steps, and landings with cement based high polymer modified quick -set tile adhesive( water based) conforming to IS-15477, using 5kg adhesive per sq.m of tile area, in average 3mm thickness (Johnson, somany ,kajaria).

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete.

(C)Wall Ceramic Glazed Tiles : 300 x 600

Providing and fixing vitrified antiskid tiles (320 x 320) and 10mm thick tiles in floor, treads of steps, landings on 25 mm thick bed of cement mortar 1:3 and jointed with cement slurry complete

Rounding of edges of kotah /granite slab to semi circular slope

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm

(a)Jet Black

Providing 25 mm thick cuddapah slabs machine cut and polished on either side in partitions including making necessary grooves in the wall and fixing with cement mortar, complete as directed by the engineer-in-charge

Kotah stone slab flooring over 20 mm (average)thick base laid over & jointed with grey cementslurry mixed with pigment to match the shade ofthe slab including rubbing & complete with baseof cement mortar 1:4 (1 cement : 4 coarse sand)

a) 20 mm thick.

Providing woodwork in frames of doors, windows, clerestory windows trusses & other frames wrought framed and fixed in position.

c) first class matti wood

Providing and fixing 38 mm thick panelledglazed or panelled and glazed shutters for doors,windows and clerestory window includinganodized aluminium butt hinges with necessaryscrews:

a) Second class Indian teak wood

Providing & fixing flush door shuttersdecoration type core of block board constructionwith frame of first class hard wood and wellmatched first class Indian teak ply veneeringwith vertical grains and cross bands and faceveneers on both faces of shutters.

b) 35mm thick including anodized aluminium butthinges with necessary screws:

Extra for providing vision panel not exceedin0.1 sq.m. in all types of flush doors (cost of glassexcluded)

a Rectangular or square Unit: SQ.M. door area

Single Colour Foam Core FRP (Fiber Reinforced Polymer) Door Shutter Manufacture, Supply and Installation (including accessories as mentioned below) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) door shutter of specified thickness as per options below by using tray system with seasoned hard wood, moisture less than 17%, wood styles for Top rail and lock rails. FRP (Fiber Reinforced Polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps) . The core of shutter will be filled as specified (Expanded Polystyrene Foam / Polyurethane Foam (EPS/PU) Foam). The shutter to be of single colour & water proof as well as mild acid / alkali resistant manufactured using RV TIFAC (R V Engineering College, Bangalore & Technology Information Forecasting & Assessment Council) technology in line with IS 13034 1990 test Standard in an ISO 9001 – 2015 certified factory.

Accessories:

i) S. S. Hinges 4” - 3 Nos

ii) S. S. Latch - 1 No

iii) Tower Bolt 5” - 2 Nos

iv) Handle 5” - 2 Nos

Shutter Thickness b) 35mm

Providing & fixing anodised aluminium sliding door bolt anodised transparent or dyed required colour and shade with bolts, nuts and screws etc. complete ( ISI mark, Heavy )

Providing and fixing anodized aluminium flat latch

Providing and fixing aluminium tower bolt (barrel type) anodised or dyed to required colour or shade with screws etc complete.

( ISI mark, Heavy )

Providing and fixing aluminium handle anodized or dyed to required colour or shade with screws etc. ( ISI mark, Round, Heavy)

Providing and fixing 150mm bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete

Providing and fixing first class Indian teak wood moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surfaces etc.

Providing and fixing brass hydraulic door closer of make Everest/ universal/ Godrej with necessary screws and fittings complete.

Providing flat iron hold fast 40 cm including fixing to frame with 10mm dia bolts , nuts and wooden plugs and embedded in cement concrete blocks 30 x 10 x 15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 stone aggregate 20 mm nominal size

b) 40 x3 mm flat iron hold fast, 15 cm long

Providing and fixing stainless steel (Grade 304)railing made of Hollow tubes, channels, platesetc.with hairline finish, including welding,grinding, buffing, polishing and makingcurvature (wherever required) and fitting thesame with necessary stainless steel nuts andbolts complete, i/c fixing the railing withnecessary accessories & stainless steel dashfasteners, stainless steel bolts etc., of requiredsize, on the top of the floor or the side of waistslab with suitable arrangement as per approvalof Engineer, ( for payment purpose only weightof stainless steel members shall be consideredexcluding fixing accessories such as nuts, bolts,fasteners etc.).

Providing and fixing M.S grill of required pattern in wooden frames of windows etc with M.S flats square or round bars with round headed bolts and nuts or by screws.

a) Plain grill

Making holes in RCC structure i.e. slabs, beams and columns by core cutting upto required depth & size up to 5" dia

Providing and fixing Aluminium shutters (Jindal make), 40mm series double openable shutters as per design including transportation, scaffolding and handling etc, complete. Windows with openable double shutters with outer frame 39 mm x 40 mm and shutters 54 mm x 40 mm with aluminium cleating system on SS 304 friction stay hinges, fixed mullion, single point locking, fixing screws of HILTI make with GP silicon.

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in?charge: Fixed partitions

a) Acryllic sheet

b) plane plate glass

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in?charge: Single or double leaf door shut

a) Acryllic sheet

b) plane plate glass

Providing and fixing Aluminium shutters (Jindal make), 27mm-Domal series windows aluminium cleating system as per design including transportation, scaffolding and handling etc, complete. Windows with three track ,three sliding shutters with outer frame 100.6mm x 45mm and shutters 65mm x 27mm kinlong touch lock, epdm gasket, all screws of S.S 304 grade fixing screws of HILTI make complete with G.P Silicon ( excluding GST)

(i) 5mm clear annealed glass of St. Gobain/AIS.

Providing and fixing 8mm Aluminium grill for AC duct with aluminium back up frame section of 63 x38 mm as per grill design with gap of 80mm including powder coating, etc.complete

Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section

12mm cement plaster 1:4 ( 1 cement : 4 coarse sand )

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1;5 ( 1cement : 5 coarse sand ) and top layer 6 mm thick with cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with sponge

Extra for plastering done on mouldings, cornices, or arches including neat finish to line and level

a) In one coat

6mm cement plaster to ceiling 1:3 ( 1cement : 3 fine sand)

18mm thick plain cement mortar bands in cement mortar 1:4 (1 cement : 4 fine sand) 1 meter long, 1 cm wide

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Extra for providing and mixing water proofing material proportion recommended by the manufacturers

a) 12mm cement plaster 1:3 ( 1cement: 3 sand)

Applying priming coat with ready mixed primer of approved brand and manufacture on WOOD WORK complete

Painting two or more coats (excluding priming coat ) with superior quality ready mixed paint(satin finish) for WOOD WORK of approved brand & manufacture in all shades on NEW WORK to give an even shade

Painting three or more coats with acrylic exterior paint of approved brand and manufacture ( such as weather shield, Apex) including applying one coat of cement primer and one coat of surface treatment etc. complete

Applying one coat of cement primer of approved brand and manufacture on wall surface.

Wall painting ( two or more coats) with plastic emulsion paint of approved brand and manufacture including a priming coat on NEW WORK to give an even shade

Providing waterproofing treatment over the RCC roof terraces by speading cement slurry over the RCC slab and laying of 10 cms, average laterite stone ballast coba with the necessary gradient for easy flow of rain water and the coba in covered terraces and balconies with damp proof of jointless water proofing plaster of mix 1:3 (1 cement :3 fine sand), finished smooth with wooden trowel with false markings of 30cm square.The vertical surface of the adjoining walls are to be treated up to a height of 30 cms including rounding of junction(the rate includes for complete items including labour and materials and including bcost of initial treatment of roof slab as follows. The injunction of damp proof or equivalent compound with cement solution will be given as and when necessary for filling honey combs ,cracks etc in the RCC slabs)NOTE:cement consumption 25 Kg/ sq.m

Providing and filling in the sunken slabs with C.M 1:4 . Broken laterite soling stones to be laid in layers with mortar and top layer of I.P.S finish (1:2:3) over brickbat coba filling etc complete in all floors.

Neat cement punning

Providing anti – termite treatment to buildingsconforming to I.S.S. 6113 part II 1971 (revised)including adopting precautions for healthhazards and safety measures as required therein with the cost of all materials, chemicals, plants,equipments required for the treatment and furnishing a guarantee for a minimum period of 10 years from the date of completion including eradicating any infestation of termite free of cost during the guaranty period complete. (Thepayment will be made on plinth of the building.

a)Pre-construction

Providing & Fixing of Aluminium Lay-in Perforated Tile Ceiling on 24 /14 mm ‘T’ Framework of module 600mm x 600mm. Tiles of size 575mm X 575mm / 584mm x584mm made out of 0.6mm thick Aluminium. Perforation of the tiles shall be 2.5mm dia 5.5mm c/c. The Tile shall be manufactured on advanced equipment, which includes several levelling. The tile end shall be raised upward by 38mm and bend outward to lay the tile in framework. The Tile shall be Polyester based, powder coated in white colour. Grid system for fixing ceiling tiles shall comprise of Tees. The 24 /14 mm main tee runners shall be suspended at an interval of 1200mm centre to centre. The 24 /14 mm cross tee runner shall be suspended at 600mm centre to centre and further supported with 24 /14 mm cross tee at 600mm centre to centre with interlocking arrangements to form grid of 600mm x 600mm. The main tee shall be supported by means of 4mm G.I. rod from slab/roof. The suspension shall be provided at 1200 to 1500mm centre to centre. Tee framework would be made of GI and Powder coated. Acoustic Felt: Non-woven felt made of glass-reinforced fibre glued over the perforation for sound absorption.

Gypliner or equivalent ceiling which includesproviding & fixing G.I. HG angle of sie 0.55 mm thick having two equal flanges of 25 mm each screw fixed to brick wall / partition with the help of nylon sleeves & screws at 610 mm c/c. Then suspending chan 12.5 mm tapered edge Gypboard (confirming to IS:2095-1982) is then fixed to channel section with 25 mm drywall screws at 230 mm centre. Screw fixing is done mechanically with drill machine and suitable attachment. Finally square and tapered edges joints of the boards are jointed and finished so asto have flush look which includes filling finishingwith jointing compound, joint paper tape and two coats of Drywall top coat suitable for Gypboard (as per recomended practices of India Gypsum Limited).

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. of make ASTRAL/ASHIRWAD

a)15 mm dia nominal outer dia pipes.

b)20 mm dia nominal outer dia pipes.

c)25 mm dia nominal outer dia pipes.

d)32 mm dia nominal outer dia pipes.

Providing and fixing ASTM UPVC pipe,conforming to ASTM 2467 with ISO 14001,including all UPVC plain & brass threadedfittings, including fixing the pipe with clamps at1.00 m spacing. This includes jointing of pipes &fittings with one step UPVC solvent cement andtesting of joints complete as per direction ofEngineer. Internal work - Exposed on wall.

I SCH-80(blue)/(white)

a)20mm outer dia

b) 25mm outer dia.

c) 32mm outer dia.

d) 40mm outer dia.

e) 50mm outer dia.

Providing and fixing ASTM UPVC pipe,conforming to ASTM 2467 with ISO 14001,including all UPVC plain & brass threadedfittings, including jointing of pipes & fittings withone step UPVC solvent cement, trenching ,refilling & testing of joints complete as perdirection of Engineer. External work.

I SCH-80(blue)/(white)

c 32mm outer dia.

d 40mm outer dia.

e 50mm outer dia.

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed:

a) 110 mm dia

b) 75 mm dia

Providing and fixing single Tee of rigid PVC(approved make ) for S.W.R. pipes includinglubricating etc complete, with door :

a) 110 mm dia

b) 75mm dia

Providing and fixing single “Y”of rigid PVC S.W.R pipes (soil, waste & rain water drainage pipes of approved make including lubricant etc. complete ,with door

a) 110 mm dia

b) 75 mm dia

Providing and fixing rigid PVC bend ( approved make) for SWR pipes including lubricating etc complete, with door

a)110 mm dia

b) 75mm dia

Providing and fixing double “Y”of rigid PVC S.W.R pipes (soil, waste & rain water drainage pipes of approved make including lubricant etc. complete ,with door

a) 110 mm dia

b) 75 mm dia

Providing and fixing R.P.V.C vent cowl

a) 110 mm dia

Providing and fixing square-mouth S.W. gully trap grade ‘A’ complete with c.i. grating brick masonry chamber and water tight C.I. cover with frame of 300 x 300 mm size (inside the weight of cover to be not less than 4.53 kg). And frame to be not less than 2.72 kg as per standard design :

b) 150 x 100 mm size –P or S type

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) RCC top slab with 1:2:4 mix (1 cement : 2 Coarse sand : 4 graded stone aggregate 20mm nominal size foundation concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 40mm nominal size )inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1cement :2 coarse sand :4 graded stone aggregate 20mm nominal size ) neatly finished complete as per standard design.

d) Inside size 60 x 60 cm and 60cm deep including C.I cover with frame (light duty ) 455 x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 Kg)

b) Inside size 90 x 80 cm and 60 cm deep including C.I cover with frame ( light duty ) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg ( weight of cover 23 kg)

Extra for depth for manholes : a) size 90 x 80 cm

Providing and fixing NICKEL chrome platedcopper alloy Fancy BIB Cock Short Body Jaquarmake or equivalent. Confirming to IS 8931;1993

a)15mm nominal bore

Providing and fixing Nickel chrome plated copper alloy BIB cock (long body) JAQUAR make with wall flange or ARK SUPREME confirming to IS 8931; 1993

a) 15 mm nominal bore

Providing and fixing NICKEL chrome platedcopper alloy Fancy two way long body bib cockwith wall flance Jaquar make or ARK supremeConfirming to IS 8931;1993

a) 15 mm nominal bore

Providing and fixing Nickel chrome plated copper alloy BIB cock (long body) JAQUAR make with wall flange or ARK SUPREME confirming to IS 8931; 1993

a) 15 mm nominal bore

Providing and fixing NICKEL chrome platedcopper alloy Fancy two way long body bib cockwith wall flance Jaquar make or ARK supremeConfirming to IS 8931;1993

a) 15 mm nominal bore

Providing and fixing C.P concealed angle stop cock (heavy) with wall flange of (ARK SUPREME/JAQUAR) make 15 mm nominal bore

Proving and fixing white vitreous china watercloset squatting pan (Indian type w.c. pan) size580 mm with 100 mm sand cast iron P. or S trap10 litres high level P.V.C. flushing cister (ofapproved make) with fittings, rack bolts 32 mmdiameter P.V.C telescopic flush pipe with fittings and clamps 25mm P.V.C. over flow pipe with specials & mosquito proof coupling ofapproved municipal design and nylon pullcomplete cutting and making good the walls andfloors where required(HINDUSTAN/CERA)

b) Orissa pattern W.C. pan

Providing and fixing vitreous China water closet squatting (European type W.C pan) with seat and lid C.P brass hinges and rubber buffers 10 lts high level PVC flushing cistern ( of cera conventional “s” /p trap) with fittings rack bolts, 32 mm, dia PVC telescopic flush pipe with fittings and clamps 25 mm PVC over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon chain and pull complete, cutting & making good the walls & floors where required. ( HINDUSTAN/CERA)

a) WC pan – Hindustan /Cera conventional EWC of white colour with white plastic lid & seat.

b) PVC FLUSHING CISTERN ( HINDUSTAN/CERA)

White colour Hindustan sleek with all fittings.

Providing and fixing vitreous china under counter wash basin inclusive of all fixing accessories and Jaquar make fittings etc. complete. -JAQ ALD-CHR-709 L130 coupling -JAQ ALE-CHR-773 ML190X125 bottle trap -JAQ-PRS-CHR-031 Pillar Cock auto closing system-18’’ connection pipe of ARK make a) White colour under counter rectangular wash basin of size 485 x 370 x 205 mm.Jaquar make.

Providing and fixing vitreous china wall hung wash basin inclusive of all fixing accessories and Jaquar make fittings etc.complete. -JAQ ALD-CHR-709 L130 coupling -JAQ ALE-CHR-773 ML190X125 bottle trap -JAQ-PRS-CHR-031 Pillar Cock auto closing system -18’’ connection pipe of ARK make a) White colour under counter rectangular wash basin of size 420 x 420 x 155 mm. Jaquar make.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 including cutting of stone and making good the walls wherever required : Kitchen sink with drain board with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete

(a)Overall size 1040mmx510mm (41"x20") bowl size 460mmx410mmx200mm (18"x 16"x 8") depth 200 mm. Glossy. 1.0mm thk,

Providing & fixing bevelled edge mirror ofsuperior glass (5mm thk) of approved Quality,shape & size complete with CP brass screws andwashers, Cleats, CP studs etc Complete.

Providing and fixing C.P jali (Round)

Providing and fixing nahani trap of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, without door :

a) 110 mm dia

Providing & fixing CP brass towel rail fixed in wooden cleats with CP brass screws

a) 24” size CAN- CHR- 1111SM, Jaquar make

Making connection of G.I distribution branch with main 50mm to 80mm nominal bore by providing and fixing tee including treading the pipe etc complete.

Providing and fixing P.V.C. connection pipe with brass unions 15 mm nominal bore:

c) 18” (45 cm) length (ARK make)

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality. ZOLOTO make

b) 20 mm nominal bore

c) 25 mm nominal bore

d) 32 mm nominal bore

e) 40 mm nominal bore

f) 50 mm nominal bore

g) 65 mm nominal bore

Providing and placing on terrace roof of floor two (1st floor roof) single piece rotational moulded polythene water storage tank having ISI mark and confirming to IS 12701; 1996 including tank connectors.

b) 500 lit. capacity

c) 1000 lit capacity

Jointing of rigid SEL FIT PVC pipes by cleaning the pipes with solvent cement including the cost of solvent cement and hydraulic testing of joints etc. complete as per IS : 7634- 19 75 Part : 3, including hydraulic testing of joints as directed by the Engineer in Charge

Outer dia in mm

Conveying carefully from stack at site, 250mm from both sides rolling and lowering in trenches, laying true to line and level and perfect linking for joints for PVC/HDPE complete in all respects as per the direction of the Engineer-in-Charge

Supplying at store or site of work Rigid PVC (SEL FIT) pipes for public water supply including Railway freight, carting, loading and unloading, stacking, transit insurance etc. complete, Conforming to IS: 4985-2000, and bearing ISI mark, Class 6 kg/cm2. Outer Dia in mm

Supplying at store or site of work Rigid PVC (SEL FIT)pipes for public water supply including Railway freight,carting, loading and unloading, stackig, transit insuranceetc. complete, Conforming to IS: 4985-2000, and bearingISI mark, Class 10 kg/cm2.

Outer Dia in mm

Supplying and fixing at the site of work of Steel FibreReinforced Concrete (SFRC) manhole covers withframes made as per IS :12592 (part I and II )- 1991 inconcrete M45grade. The covers and lapped in 2mmthick. steel plate and this plate & lifting hooks are dulypainted in corrosion resistant epoxy paint etc. complete.

I Light Duty ( 2.50 Metric Tonne Capacity)

Size in mm

Providing & fixing soap dish chromium plated fixed to wooden cleats with CP brass screws.

a) Soap dish, JAQUAR make

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards.( Jaquar or ARK supreme)

Providing and fixing CP Brass toilet paper holder fixed to wooden cleats with CP brass screws a) JAQUAR make(CHR-1151N)

Providing and fixing urinal valve auto closing system CP with built in control cock with 8 mm dia 300 mm long pipe, wall flange etc. complete. JACQUAR make (PRS-CHR-077)

Providing and fixing WHITE vitreous china flat back lipped front Urinal basin of JAQUAR Make inclusive of C.P waste coupling, dome shaped, Urinal spreader, Urinal bracket ( Cat no :URS-WHT-13257)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of (SAIL, TATA. VIZAG, JSW ,APOLLO Steel Ltd.) make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Steel work welded ( SAIL, TATA, VIZAG & using electrodes of AdOr make only) in built up sections trusses and framed work including cutting, hoisting, fixing in position with anchor fasteners ( Hilti HST) and applying zinc chromite primer

b) In tees, angles ,flats and channels as per the design

Applying one or more coat of Zinc epoxy primer on steel work of approved brand & Manufacture (Asian/berger) on New work to give an even shade

Painting two or more coats (excluding priming coat) of Epoxy Paint for Steel Work of approved brand (Asian/Berger) on New work to give an even shade.

Providing and fixing colour coated galvuliumroofing sheets of 0.5mm thickness including allthe accessories (TATA / JSW make) but excluding thecost of purlins, rafters, trusses, flashings etc.complete as per the directions of the Engineer incharge.

Providing and fixing colour coated Galvulium Flashings of 0.5 mm thickness( TATA / JSW Make) in - corners,ridges,valleys, gable end and trims Girth up to 610 mm including all the accessories complete as per the directions of the Engineer in Charge.

Providing and fixing 0.50mm thick colour coated galvulium Rain Water gutter with machine cut and press bend in as per approved design in line level along with gutter strip, silicon sealant, SDS, etc.complete.

Construction of embankement with approved material obtained from borrowpits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting with vibratory roller to meet requirement of Table 300-2 as per MORTH specification 305

Supplying of laterite stone soling of size 150-200 mm size and murrum having P.I. Value not more than 6 and laying including packing with smaller stones and consolidation with power road roller including spreading, watering and consolidation of binding material etc.(Measurements shall be considered on finished item) .

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand ) including testing of joints, etc. complete b) 250mm dia RCC pipe

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc. shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm. b) 60mm thick in grey colour (M35 Grade)

Design , supply ,installation testing and commissioning of Raw Panel extension of existing panel in main panel room of Science Faculty, cubical type ,floor mounted , front access ,fully compartmentalised with busbar and cable chambers, with cable entry at top, all mccbs with rotary handles ,with thermal magnetic releases or as indicated. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating RAL7032.The cable terminations shall be suitable for cable sizes as shown on the drawing as required etc. with

2000A 4P bus bar 50KA extended from the existing raw power panel and same type of that panel, approximately 5metres complete with necessary supports etc.

2000A 4P copper busbars extensible at bottom, 50KA with following outgoins:

1 nos of 500A 50KATPN MCCB with on/off indicating lamps suitable for 3x31/2x300sqmm AYFY cables

2 nos of spare compartment for 400A TPN MCCB

Panel extension of Raw power panel as above

Design , supply ,installation testing and commissioning of DG Back up Power Panel extension of existing panel in main panel room of Science Faculty with DG back up, cubical type ,floor mounted , front access ,fully compartmentalised with busbars chamber and cable chambers with cable entry at top, all mccbs with rotary handles ,with thermal magnetic releases or as indicated. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating RAL7032.The cable terminations shall be suitable for cable sizes as shown on the drawing as required etc.

1200A 4P bus bar extended from the existing DG Backup panel approximately 1.0 metre with necessary supports etc.

1200A 4P copper busbars 50KA extensible from bottom with following outgoings

1 nos of 500A 50KATPN MCCB with on/off indicating lamps suitable for 3x31/2x300sqmm AYFY cables

2 nos of spare compartment for 500A TPN MCCB

Panel extension of DG back up panel as above

Design , supply ,installation testing and commissioning of RAW Panel , cubical type ,floor/wall mounted , front access ,fully compartmentalised with incomer cable entry at bottom and outgoing at top, all mccbs with extensible rotary handles ,with thermal magnetic releases and 35KA. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating of RED colour for incomer door and RAL7032 for others. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear. The cable terminations shall be suitable for cable sizes as shown on the drawing / as required etc. with

Incomer 500A TPN MCCB suitable for 3x3.5x240sqmm AYFY cable with RYB lampset and digital Ammeter, Voltmeter, KWH meter etc. with scada connectivity

1200A 4P bus bars with following outgoings

Outgoing1 with 1 no of 200A 35KA TPN MCCB with 400A 4P busbars with 7 sets 60A 35KA TPN MCCBs and 3 sets of 40A 35KA TPN MCCBs

Outgoing2 with 200A 35KA TPN MCCB with 400A 4P busbars with 9 sets 60A 35KA TPN MCCBs.

Outgoing3 two sets of 100A 35KA TPN MCCBs each suitable for 3.5x95sqmm AYFY cable

Main RAW panel as above

Design , supply ,installation testing and commissioning of DG BACKUP Panel , cubical type ,floor/wall mounted , front access ,fully compartmentalised with incomer cable entry at bottom and outgoings at top bottom, all mccbs with rotary handles ,with thermal magnetic releases and 35KA. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating of RED colour for incomer door and RAL7032 for others. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear. The cable terminations shall be suitable for cable sizes as shown on the drawing / as required etc. with

incomer 500A 35KA TPN MCCB suitable for 3x3.5x240sqmm AYFY cable with RYB lampset and digital Ammeter, Voltmeter, KWH meter etc. with scada connectivity

1200A bus bars with following outgoings

Outgoing1 with 1 no of 200A 35KA TPN MCCB with 400A 4P busbars with 7 sets 40A 35KA TPN MCCBs and 1 sets of 60A 35KA TPN MCCBs

Outgoing2 with 200A 35KA TPN MCCB with 400A 4P busbars with 10 sets 60A 35KA TPN MCCBs.

Outgoing3 with 100A 35KA TPN MCCB suitable for 3.5x95 sqmm AYFY cable

Outgoing4 with 300A 35KA TPN MCCB suitable for 2x3.5x240 sqmm AYFY cable with top outgoing

Main DG BACK UP panel as above

Design , supply ,installation testing and commissioning of UPS Panel , cubical type ,floor/wall mounted , front access ,fully compartmentalised with incomer cable entry at bottom and outgoing top, all mccbs with rotary handles ,with thermal magnetic releases and 35KA. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating of RED colour for incomer door and RAL7032 for others. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear. The cable terminations shall be suitable for cable sizes as shown on the drawing / as required etc. with

incomer 250A 35KA TPN MCCB suitable for 2x3.5x240sqmm AYFY cable with RYB lampset and digital Ammeter, Voltmeter, KWH meter etc. with scada connectivity

800A 4P bus bars with following outgoings

Outgoing1 with 100A 35KA TPN MCCB with 200A 4P busbars with 4 sets 40A 35KA TPN MCCBs

Outgoing2 with 200A 35KA TPN MCCB with 400A 4P busbars with 9 sets 60A 35KA TPN MCCBs.

Main UPS panel as above

Design , supply ,installation testing and commissioning of UPS Room incomer and outgoing Panel , cubical type wall mounted , front access ,fully compartmentalised with cable entry at top/ bottom, all mccbs with rotary handles ,with thermal magnetic releases and 35KA. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating of RED colour for incomer door and RAL7032 for others. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear. The cable terminations shall be suitable for cable sizes as shown on the drawing / as required etc. with

incomer 250A TPN MCCB suitable for 2x3.5x240sqmm AYFY cable with RYB lampset and digital Ammeter, Voltmeter, KWH meter etc. with scada connectivity

400A bus bars

Outgoing with 3 set of 100A 35KA TPN MCCB suitable for 4c50sqmm copper wires

UPS units incomer and outgoing panel as above

Supplying, installation, testing and commissioning of main fire pump (MFP / EP) suitable for water discharge of 1600 to 1800 LPM at 70 to 55 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 30kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal type, single stage, centrifugal/split casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/EP

Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG

Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PS

Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying, erecting, testing & commissioning of fire pump control panel (FCP) of cubical construction, floor mounted type, fabricated from minimum 2 mm thick CRCA sheet, compartmentalised with hinged lockable doors, with enclosure protection class IP54, duly powder coated or painted with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003), cable alley, interconnection with suitable size solid copper busbar strip of adequate size for all power connections having switchgears and accessories, mountings and internal wiring with adequate size copper conductor cable, earth terminals, numbering etc. complete in all respect, suitable for satisfactory operation of main fire pump and jockey (pressurisation) pumps (1working+1standby) with necessary accessories, wiring & cabling along with allied accessories with following incoming and outgoings, suitable for automatic & manual operation on 415V, 3 phase, 50Hz ac supply as per specifications

Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP

Supplying and erecting 63mm dia, reinforced rubber lined (R.R.L.) hose pipe, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL

Supplying and erecting stainless steel branch pipe 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specifications no. FFFFA/ NZ

Supplying and erecting stainless steel single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV

Supplying and erecting fire brigade header ( Siamese connection )of 150 mm dia, for supplying water in fire tank complete as per specification no. FFFA/ FMC)

Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying & installing of Signages for Exit/Extinguisher/Call Points/ Hose Station And Evacuation Layout. Etc (Prolite Make)

S u p p l y i n g & erecting ABC 6 Kg Fire Extinguisher (Ligtex Make). capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

S u p p l y i n g & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

Supplying & installing Structural Support (MS C Channel and L- Angle of appropriate size)

Supplying & installing Push button at ground floor with cable

Foot Valve- Normex Make (negative suction ) 80NB

Supplying, installing, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the 2 loop capacity and capable of supporting upto 250 devices and detectors per loop, with on-board LCD display with min 16 lines of text, operating at 230 V 50 HZ - AC with inbuilt Battery Backup of a minimum 24 hours in normal condition and 30 min in alarm condition, suitable provision for network connectivity, interfacing with third party equipment via a MODBUS/ OPC/ L-ON interface etc. conforming to IS 15908:2021, IS 2189: 2008, EN 54 & VDS / FM/ UL 864 (10th edition) with 3 years replacement warranty FF-AFAS/CP.

Supplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU

Supplying, erecting, testing and commissioning hooters having high (100dB @ 1m) and low (94dB @ 1m) volume setting, group addressing facility allowing multiple sounders to be activated with CRCA enclosure complete as per specification no. FF-FAAS/HTR

Supplying, erecting testing and commissioning manual call point (Pill box) with break glass, push button (resettable type) in metal enclosure complete as per specification no. FF-FAAS/MCP

Supplying, erecting testing and commissioning optical type smoke detector on suitable back box with necessary connections complete as per specification no. FF-FAS/SD

Supplying, installing, testing and commissioning of addressable fire isolator module complete as required. EN 54 /FM or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/ISM

Supplying and installing wall mounting swinging hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) along with necessary accessories complete as per specification no. FF-FFA/HV

Supplying and erecting 100 mm dia Cast Iron end line strainer of Y-type flanged end pattern, PN16 pressure rating, SS screen, end connection with Flanged / Screwed / Socket Weld / Butt Weld End etc with standard OAR (open area Ratio) for positive suction complete as per specification no. FF-VL/ELS

Supplying and installing one piece moulded HDPE / fibre water tank for negative suction only, having capacity 1000 litres fitted with necessary accessories complete as per specification no. FF-FFA/PT

Supply of armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I),IS:7098(Part I) with latest amendments of following size.

(10) 3 1/2cx300 sq.mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of exceeding 120 sq.mm but not exceeding 400 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required.

b) In rocky strata

Laying of one number additional PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 120 sq.mm but not exceeding 400sqmm direct in ground in the same trench in one tier horizontal formation including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick, protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required.

b) In rocky strata

Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required.

(11) 3 1/2 x 300 Sq. mm.

Steel work in single sections (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only) including cutting, hoisting fixing in position and applying a priming coat of red lead paint.

a) In R.S. joists, channels, angles, tees

b ) In flats of all sizes

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. b)Watering GI pipe, 20mm, Class B, with funnel as per specs. c)Charcoal/salt as per specs (paid separately). d) Refilling the pit of size 1.0x1.0x 3.0mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe.g)watering arrangement(plumbing will be paid separately).

(b) In rocky strata

Extra for using salt and charcoal for GI or Copper plate earth electrode as required (96kgs of charcoal and 5kgs of salt)

Supplying and laying 25 mm x 6 mm GI strip at 0.5 m below ground as strip earth electrode including soldering etc. as required

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with modular switch, modular plates,suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

(f) Group C -- with Cat B Modular Accessories

Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with 2 way modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

(a) with Cat A Modular accessories

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch connection painting etc. as required.

(b) Cat B

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 A and 5/6 A modular socket outlet modular socket outlet and 15/16 A modular switch connection painting etc. as required. (b) Cat B

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit (heavy)of appropriate size as required.

(b)2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

(c) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit)

(j) 4 x 6 sq.mm + 2 x 6 sq.mm earthwire (32mm Conduit)

(k) 4 x 10 sq.mm + 2 x 10 sq.mm earthwire (32mm Conduit)

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required

(b) Cat B

Supply and erecting fan hook box ( 100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel upto 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required.

Supplying and erecting of 48 inch (1200mm sweep) ceiling fan, double ball bearing type complete with all accessories

(b) Cat B

Supply and erecting of 9 inch (225 mm sweep) exhaust fan with double ball bearing 1400 rpm, complete with all accessories.

(a) Cat A

Supplying and erecting slotted angles, frames, strips, etc. for fixing of trays complete with bending, cutting, drilling and welding complete erected at the position with necessary materials such as nut bolts,etc duly painted with one coat of red oxide and two coats of enamel paint to match the structures or as per directions

Supplying and fixing following way TPN sheet steel, double door, Verticle type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)interconnection between incomer MCB and busbars of following ways (but without MCBs as required)

(d) 4 way (8+12), double door, Vertical type, Cat B

(e) 8 way (8+24), double door, Vertical type, Cat B

(f) 12 way (8+36), double door, Vertical type, Cat B

Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required (but without MCB/RCCB/Isolator)

(i) 4 way single door Cat B

(k) 12 way single door Cat B

Supplying and fixing B series SP MCB 240V, suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required"

(c )5A TO 32A, Cat B

Supplying and fixing 40 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required.

(f) SP, Cat B

Supplying and fixing 63 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required.

(i) TP Cat B

(h) DP, Cat B

(J) TPN Cat B

Supplying & erecting LED 40W tube light fitting (4 feet), 5700K, with CRCA housing, heat sink, with industrial grade heavy duty driver complete Havels Cat stout mini 1200bs 40w led 865 spcwh OR Wipro cat no LL24-541-XXX-57-CD (including lamp).

Supplying and fixing stiff pendant with 600 mm long 20 mm dia x 1.6 mm thick steel conduit aluminium cast back plate and brass holder complete including wiring the down rod with 1.5 sq.mm FR PVC insulated copper conductor single core cable and painting etc. as required.

Supply and fixing of cable route marker 15 cms diameter of GI plate 6mm thick with inscription thereon bolted or welded to 25mm x 25mmx 5mm angle iron 60 cms long and fixing the same in ground with PCC etc complete as required.

Supplying & laying (including excavation) 15 cm dia RCC Hume pipe with coupling collar of standard thickness at required depth up to 90 cm below road / ground surface, for enclosing provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet).

Supplying and Installing following size perforated type 16 SWG, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required.

100mm width x 50mm depth

150mm width x 50mm depth

Supplying and Installing following size perforated type , M.S.cable tray bends of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required.

100mm width x 50mm depth (16 SWG)

150mm width x 50mm depth (16 SWG)

Supplying and Installing following size perforated type , M.S.cable tray tees of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required.

100mm width x 50mm depth (16 SWG)

150mm width x 50mm depth (16 SWG)

Supplying and Installing following size perforated type 14 SWG, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required.

450mm width x 50mm depth

Supplying and Installing following size welded ladder type , 50mm depth, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required.

150 mm width X 50 mm depth with runner size 15x50x15mm, rung size 20x40x20mm with rungs at 250mm c/c.(14SWG)

600 mm width X 50 mm depth with runner size 15x50x15mm, rung size 20x40x20mm with rungs at 250mm c/c.(12SWG)

Supplying and fixing tool-less shutter keystone jack (RJ-45) in provided patch panel complete as per specification no. WG-NAS/KJ

Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 500x600x500 mm) as per specification No. WG-NAS/RAK

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NA

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and drawing of Cat - 6 UTP, 4 pair annealed tinned copper conductor PVC insulated, PVC sheathed, unarmoured data cable in existing surface/recessed steel/PVC conduit of appropriate size including connection, etc. complete as required

Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with RJ-45 connector(modular LAN socket TX1000/ CAT6) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required.

SITC of Electric Traction Passenger Lift with · · ·

Rated capacity :- 8 Passenger/544Kg

Floors :- G+1 floor (2 Stops/2 Landings)

Travel :- 3 to 4.2 mtrs · ·

Rated speed :- 1.0 mps VS

Location of Lift Machine:- MR/MRL

Car/Landing door clear opening of 800 mm wide x 2000 mm high, Clear Car size of 1850 mm wide x 1770 mm deep x 2250mm high ,Lift shaft available having clear size of ......mm wide x ......mm deep,......mm Pit depth, ………mm Overhead.

Doors type :- COPO/TOPO Doors with frame made from SS 304 grade solid(non-cladded) sheet of 1.5mm thick in hairline finish for car and all landing doors with SS door architraves/frames The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory).

Lift car enclosure made from SS 304 grade solid (non-cladded) sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with ecessary false ceiling with adequate LED lights, lower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. The lift car interior design shall be done as per the directions of engineer in charge.

COP with SS face plate having metallic push buttons with Braille code & luminous indicator around button with FPI, scrolling UP/DN LED indicator &with / without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor

LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings.

Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port. The controller shall have necessary protections such as overcurrent, overvoltage, over speed, overheat for all devices including lift motor and travel direction protection, protection for phase loss at input or output etc. various operation modes such as maintenance, change direction by attendant, full load bypass, VIP call operation, self levelling operation, call cancel facility, auto return to home landing, fireman evacuation operation, earthquake operation, door open/close operation from COP etc. The system can record information for minimum 30 latest faults, with real-time clock management and handheld keypad with LCD screen for view and setting of parameters. The control panel duly wired with proper size & strength, copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class.

ARD complete with necessary SMF VRLA batteries.

Fireman controller having fireman switch at fire Landing

CCTV surveillance system comprises of 2 nos minimum 2.0 MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup min. 90 days with min. 18” FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge.

Lift Machine of Gearless PMSM of suitable kW with duty cycle of minimum 120 starts/hr (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory), with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength.

Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work.

Minor civil work such as alteration work if any necessary for erection of landing door frames and it's accessories e.g. sill, header, hole pass etc complete with plaster finish, civil work for erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails, providing and fixing steel girders/RCC work having adequate strength for mounting and hoisting lift machine etc. complete as per specification no. LFT

General: - Job includes entire procedure of obtaining all necessary erection permissions & "License to Work the Lift" from Electrical Inspector(Lifts) with submission to the Engineer In Charge. The above rate includes Fully Comprehensive AMC for one year from the date of commissioning.

The above rate includes Fully Comprehensive AMC for one year from the date of commissioning

for Additional 2MP camera with necessary accessories at Home landing

Premier Builders Goa Pvt. Ltd.