REPAIRS / REPLACEMENT TO TILING, PLINTH PROTECTION, JOINERY AND OTHER MISC B/R ITEMS IN OLD / NEW MAP ACCN IN AOR OF AGE B/R LEKHANAGAR UNDER GE NASIK ROAD

Amount

Taking down shutter of any description exc 1 sqm but n exc 2 sqm from chowkhat and removing to or from store as required complete all as specified.

Taking down shutter of any description exc 2 sqm but n exc 4 Sqm from chowkhat and removing to or from store as required complete all as specified.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) n.exc 1.50 sqm each removing from the site complete all as specified and directed.

Taking down chowkhats or frame n.exc 1.50 sqm each removing from the site complete all as specified and directed.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) exc 1.50 sqm but n. exc 4 sqm each removing from site complete all as specified and directed.

Dismantling wrought iron or mild any description such as steel gate, steel frame works, purlins, rafter, railings, balusters and window guard bars and directed by Engr-in-Charge. Note:work is to be executed for high rise bldgs.

Dismantling of steel window/ventilators any description and any size complete all as specified and directed. Note:work is to be executed for high rise bldgs.

S&F Framed work as in grill, doors or gates of angle or other section with gusset plates, braces, etc, complete, drilled for fixing of steel sheeting or other covering, Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing Fe Grade 290(Gde E-165) complete all as specified and directed by Engr-in-Charge. Note: (a) Work is to be executed at any height and situation. (b) During Fixing of chowkhat, surface shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement.

S&F for 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides particle board core including two coat of synthetic enamal paint over one coat of pink primer all as specified and directed by Engr-in-charge. NOTE :- All screws shall be self tapping chrome plated and work is to be executed at any height and situation. Note:work is to be executed at any height and situation.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge

S&F for factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of lasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge.

S&F for factory made single extruded 35mm thick WPC (Wood Polymer Composite) made glazed and skeleton open rebated, prepared to receive glass, gauze and solid decorative type door shutter,comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of lasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. Note: Wire mesh door shutter shall be factory made. Quotated rate deems to be inlcusive of all additional cost for cutting door in size and shape,wastage and wiremesh beading etc.Wire mesh shall not be paid separatly.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65x125mm (Single/double rebated) comprising of virgin PVC polymer of K value 58-60 Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being ermite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge and including M.S. hold fast/ lugs or SS dash fasteners etc.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 50X100mm (Single/double rebated) comprising of virgin PVC polymer of K value 58-60 Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being ermite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge and including M.S. hold fast/ lugs or SS dash fasteners etc.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube etc all as specified and as directed. Note: (a) Work is to be executed at any height and situation. (b) During Fixing of chowkhat, surface shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,suppling & fixing in the frame at site as per specification & drawing.Note:work is to be executed at any height and situation.

S&F factory made of 2nd class hard wood 35mm thick made glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, size of members of shutters as spfd in SSR Part-1, section 8, clause 8.24(a) complete allas specified and directed. Note:work is to be executed at any height and situation.

S&F II nd class hard wood plain,solid,straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed. Note: (a) Work is to be executed at any height and situation. (b) During Fixing of chowkhat, surface shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement.

M&L for powder coated aluminium (minimum 50 micron powder coated) frame sliding window with triple shutter, triple channel including hold fast/screw drilled, aluminium cleats, making good the disturbed area with existing finishing so as to match with under mentioned specification:- (a) Frame of window 100x45x2mm (b) Shutter top and bottom 39.40x17.76x1.5mm (c) Shutter inter lock section 38.40x17.70x1.5mm (d) Top size guide 92x31.75x1.5mm (e) Bottom guide 92x31.75x1.5mm (f) 5mm thick tinted glass with aluminium glazing clips rubber beads in area n exc 1.5 m size. (g) Stainless steel stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm. (h) Handle section 39.40x17.70x1.5mm with glazing clips, rubber beading, roller, locking plate etc. (h)During fixing of frames, surface shall be make good in plumb with existing finishes like cement plaster ,Granie, tile and filling joint between surafce and frame with silicon compund complete all as specified and directed. Note: (a) Work is to be executed at any height and situation.

M & L for Preparing new untreated steel or iron surfaces over 10cm width or girth and and two coats of synthetic enamel paint over and including a coat of red oxide. Note:work is to be executed at any height and situation.

M & L for Preparing new wood or wood based surfaces over 10cm width or girth and two coats of synthetic enamel paint over and including a coat of pink primer. Note:work is to be executed at any height and situation.

S & F 100mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21.

S&F 100mm size aluminium handles cast type (anodised), fixed with steel chromium plated bright screws complete all as specified and directed by Engineer-in-Charge.

S&F 150mm aluminium handles cast type (anodised), fixed with steel chromium plated bright screws complete all as specified and directed by Engineer-in-Charge.

S&F 300mm aluminium anodised sliding door bolt with hasp staple (Bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding door bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed by the Engineer-in-Charge.

S&F 150mm aluminium anodised sliding door bolt with hasp staple (Bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding door bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed by the Engineer-in-Charge.

S & F aluminium anodised barrel tower bolt of extruded section of size 300 mm complete all as specified and directed by the Engineer-in-Charge.

S & F aluminium anodised barrel tower bolt of extruded section of size 150 mm complete all as specified and directed by the Engineer-in-Charge.

S&F 150mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor including rubber bush compete (overall length of cover plate 150mm) complete all as specified and directed by the Engineer-in-Charge.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar.

M & L for Granite (of any type) work 20mm thick machine cut, (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like laid over and including 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match.

M&L for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations. (Stone slabs so provided shall be not less than 900mm in length)

S & F in repairs Sink made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm.

Taking up or down steel tubing and connections 15mm bore etc. Note:work is to be done in multistorey bldgs(int and ext plumbing).

Refixing old steel tubing and connections 15mm bore in new or old position (Walls, ceiling, floors, etc.) including new fitting like elbow,socket etc shall be provided wherver required. Note: GI tubing shall be concealed wherever directed by Engr-in-charge. Contractors quotated rates deems to be inclusive of the said provision.

S & F 15mm bore galvanised steel water tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors. Note: GI tubing shall be concealed wherever directed by Engr-in-charge. Contractors quotated rates deems to be inclusive of the said provision.

Taking up or down steel tubing and connections 20mm bore. Note:work is to be done in multistorey bldgs(int and ext plumbing).

Refixing old steel tubing and connections 20mm bore in new or old position (Walls, ceiling, floors, etc.) including new fitting like elbow,socket etc shall be provided wherver required. Note: GI tubing shall be concealed wherever directed by Engr-in-charge. Contractors quotated rates deems to be inclusive of the said provision.

S & F 20mm bore galvanised steel water tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors. Note: GI tubing shall be concealed wherever directed by Engr-in-charge. Contractors quotated rates deems to be inclusive of the said provision.

S & F in repairs 15mm bore bib taps, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repair.

S&F in repairs hand shower (Health faucet) 1 Mtr PVC tube with wall hook (CP) complete all as specified and directed.

S & F in repair 15 mm bore fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed.

S& F in repairs 15 mm bore stop valves, cast copper alloy, fancy type, chromium plated (angle type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

S&F in repairs 15 mm bore stop valves, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm

S&F 32mm bore low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sqcm including fittings.

S & F in repairs Brass chromium plated shower rose 125mm size with swivel joint, including fixing to steel pipe or union 15mm bore.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing debris out of MOD land and rubbish off the premises. Note:work is to be executed at any height and situation.

M&L for Non skid ceramic tiles coloured 7 to 8mm thick (square/rectangular ) area of each tile exc 0.11 sqm but not exc 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match Note:Note: size,shade of tile shall be as approved by GE based on manufacturing company catalogue.

M&L for coloured glazed ceramic tile 7-8 mm thick as in dado/wall tiling over and including 10 mm thick backing coat in CM 1:4 in any position /shape/pattern. Note:Note: size,shade and pattern of tile shall be as approved by GE based on manufacturing company catalogue. work is to be executed at any height and situation.

M&L for 8-10 mm thick double charged vitrified tile as in flooring,laid in any shape/pattern over and including 15 mm thick screed in CM 1:6 as in floors. Note: size,shade of tile shall be as approved by GE based on manufacturing company catalogue. contractor quoted rate deems to be inclusive of tile of max size i.e. 600 mm x 600mm.work is to be executed at any height and situation.

M&L for 8-10 mm thick double charged vitrified tile as in skirting,laid in any shape/pattern over and including 10 mm thick backing coat in CM 1:4. Note: skirting shall be of same size and same make as for flooring.

Demolition of reinforcement cement concrete (reinforcement cut as required to faciliate demolition) of any descreption and any position not other wise specially provided including removal of debris out of MOD land and rubbish off the premises complete all as specified

Separating, scraping and cleaning reinforcement obtained from item No 03 above.

M&L for special treatment to sunken portion with 10mm thick plaster in CM 1:4 by using Ditachment DM 1% by weight of cement and surface made smooth after curing period two coat of Ditachment DS shall be applied @ 2.50 Kg/Sm. The paste like consistancy like is made by using 2.5 Kg of Ditachment DS powder in one litre of admixture (The admixture is made by dissolving 1 part by volume of Nafufill SBR & 4 part by volume of water). After 3 days curing, testing shall be done by flooding for 24 hours. Finally protective plaster coat of 10mm thick in CM 1:4 shall done by using Putz Ditachment 1% by weight of cement over layer of Detachment DS. All joints of CI Pipe, Nahani trap, WC connection etc. shall be filled by mixture of cement, fine sand and 10% Nafufill SBR by weight of cement 32mm dia 450mm long GI Spout light grade shall be provided in all sunken slabs to drain off water. Note: Each sunken treatment shall be completed within 7 days after handing over of site for sunken for a bldg in all respect including all fittings/tiling etc under normal circumstances. For delay beyond 7 day, penalty shall be charged @ Rs 1000/day and shall be recovered from contractors RAR/FB as decided by GE.work to be executed at any height and situation on urgent basis.

S&F in repair Vitreous China water closet squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests and P/S trap (excluding flushing cistern and flush pipe) complete including provision of lime concrete bedding.

S&F in repairs 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including flush pipe and brackets complete all as specified and directed.

S&F in repairs Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket ,sheet cover etc. over and including flush pipe complete in all respect all as specified.

S&F in repairs Vitreous China wash basin white, flat back, size 550 X 400mm, including cutting for and pinning in ends of brackets or erecting stand, with and including 32mm waste fitting brass, chromium plated with long screwed shank and fly-nut, flange end bedded in red lead cement, brass chromium plated bottle trap with inlet and outlet screwed for pipe or connections 32mm bore, including necessary packing, union and cap and fixed in repairs.

M&L for PVC (SWR) floor trap(75 mm dia), plain with grating including jointing with solvent cement to mitigate the site requirement to the entire satisfaction of engr-in-charge.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1998 Grade St-240 complete all as specified and as directed. Note:work is to be executed at any height and situation.

Supply and fixing in repairs 500 Litre capacity Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position including GI tank nipple etc. complete and all as specified and as directed by Engineer-in-Charge. including dismantling existing water tank and removing from site of any capacity.

Supply and fixing in repairs 1000 Litre capacity Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position including GI tank nipple etc. complete and all as specified and as directed by Engineer-in-Charge. including dismantling existing water tank and removing from site of any capacity.

S&F ball valves, 20mm bore high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210gms) fixed in repairs.

Taking down carefully existing bituminous membrane/tarfelt treatment any description and cleaning and making good damaged surface of roof ,parapet,facia etc in cement mortar 1:3/PCC 1:2:4 as directed by Engr-in-charge where ever require.quotated rate shall be deem to be inclusive of complete removal of swollen plaster and concrete wherever directed by engr-in-charge and removing rubbish out of defence land.

Demolition of concrete (unreinforced) of any description and in any position not otherwise secifically provided for.

Providing cement concrete type B0 1:2:4(12.5mm graded aggregate) in roof kerbs or mud stops,ridge, padding,rounded or chamfered on edges.

M&L for rendering 15mm thick(minimum) in CM 1:4 with intergral waterproofing compound (200 ml per bag of cement used) on roof surfaces,parapets,facias etc . Note: waterproofing compound shall be measured and paid separately.

Supplying only integral water proofing compound ISI marked complete all as specified and as directed.

M&L for applying evenly a coat of hot blown bitumen grade 85/25 over roof,facia,parapet surfaces at the rate 1.20kg per sqm for fixing app membrane etc including cleaning surfaces. Note:Make same as for app membrane.

M&L for Waterproofing on roof including flashing and junctions of parapet,kerb, wall etc.as under :- (a) Laying a layer of APP based polymeric membrane,3 mm thick(minimum),weighing not less than 3.60 kg/Sqm prefabricated fire layer waterproofing membrane reinforced with polyester non woven fabric(weighing not less than 160 gms/sqm) shall be applied over compatible primer at 0.40 litre/Sqm of density at 25 degree Centigrade 0.87-0.89 Kg /Litre and viscosity 70-160cps or cold sticker, application of APP modified membrance shall be by torch application. The overlaps shall be minimum 150mm on the transverse direction and 100 mm on the longitudinal direction. (b) APP membrance,Primer and bitumastic aluminium paint and bitumen shall be of same brand. (c) For vertical surfaces of parapet,wall etc app membrane shall be tucked into groove and sealed with silicon sealant(full width/depth of groove) i.e. "Dowsil 789 weatherproof silicon sealant" using gun. (d) Bitumen and aluminium paint shall be paid separately.

M&L for applying two coats of solar reflective bitumastic aluminium paint at the rate 0.15 kg per sqm per two coats over exposed app membrance surfaces(old/new) including cleaning of surfaces to the entire satisfaction of ground executives. Make: same as of app membrane.

Disconnecting existing tanks exc 250 n exc 500 litres setting aside (or lowering if required) cleaning and removing all scale dirt,etc from the mouth of circulating pipes etc and hoisting if required,reconnecting and re-fixing in position. Note:work is to be executed at any height and situation.

Disconnecting existing tanks exc 500 n exc 1000 litres setting aside (or lowering if required) cleaning and removing all scale dirt,etc from the mouth of circulating pipes etc and hoisting if required,reconnecting and re-fixing in position. Note:work is to be executed at any height and situation.

S & F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed.

Dismantling Plain or corrugated steel sheeting of any gauge,thickness,including Nainital or similar pattern roof coverings complete all as specified and as directed. Note:work is to be executed at any height and situation.

S & F Prepainted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/cladding to wall,fixed with self tapping screw complete all as specified and as directed. Gap between wall face and sheet if any shall be sealed using CM 1:3 with WPC.quoted rate deems to be inclusive of the same. Note:work is to be executed at any height and situation.

S & F Prepainted Galvalume aluminium zinc coating GI based Plain sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/cladding to wall,fixed with self tapping screw complete all as specified and as directed. Note:work is to be executed at any height and situation.

M&L for PCC 1:2:4 using 40 mm graded aggregate as foundation filling and mass concrete.

Taking down AC rain water pipes(any size or pattern) including all fittings,head shoes,bends,swan neck etc. Note: work to be executed at any height and situation.

S & F PVC (SWR) pipes110 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls as RWP including fixing clamp. Note: work to be executed at any height and situation.

S & F PVC (SWR) pipes 75 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors.

S&F 110mm PVC (SWR) bends any radius

S&F 75mm PVC (SWR) bends any radius

Demolition of concrete (unreinforced) of any descriptionand in any position not otherwise secifically provided for i.e sub bases of floor,plinth protection etc.

Demolition of cement concrete in ground floor and pavings n.exc 15cm thickness (below or above ground level).

M&L for 75mm thick PCC 1:4:8 Type D-2(using 40mm graded aggregate) as in sub base over rammed earth complete all as specified and as directed.

M&L for Chequered cement concrete tiles with grey cement and pigment 30cmx30cmx25mm thick, with rubber moulded glassy finished surface, laid in floors over and including 15mm thick screed bed or beddingin CM 1:6 pointed in neat cement slurry in floors.

M&L for rough shahabad stone 25mm to 30mm thick in flooring /plinth set and jointed in neat cement slurry over and including 15mm thick screed bed or beddingin CM 1:6 pointed in neat cement slurry in floors.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper mbedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping complete all as specified and directed

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. Note: work to be executed at any height and situation.

M&L for brick work with fly ash bricks straight or curved on plan exc 6 m mean radius built in CM 1:6.

M&L for Rendering 15 mm thick in cement mortar 1:4 on wall/ceiling surfaces finished fair and even incl curing. Note:For multistorey bldgs only sccaffolding/ladder shall be used. work to be executed at any height.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 42,930.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

Vinod Enterprises

sunway associates

M/S SAMEER SUBHASH PATANI

M/S R.K.S. CONSTRUCTION

Bidder Name

M/S SAMEER SUBHASH PATANI

sunway associates

Vinod Enterprises

M/S R.K.S. CONSTRUCTION

Abhiraj Enterprises