Construction of Veternary Hospital Building at Sherpur in Tehsil Dalhousie Distt. Chamba

Amount

Excavation in foundation trenches etc. in earth work in all kinds of classification of soil such as pick work, jumper work, pick jumper work, blasting work, soft and hard blasting and doing work in saturated soil, including chiseling or wedging out rock where blasting is prohibited, or any other mixed variety of soil including shoring, strutting, de-watering and pumping or bailing out water (surface and sub soil water) upto any depth or any quantum of water including slush which may arise during dewatering, removal of slush and stacking the excavated soil clear from the edge of excavation with in all leads, as directed by Engineer-in-Charge and then returning the stacked soil in 15cm (fifteen centiMetres) layers when required into plinths, sides of foundations etc. consolidating each deposited layer by ramming watering and then disposing of all surplus excavated earth and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:6:12 (one cement isto six sand isto twelve graded crushed stone aggregate 40 mm (forty milliMetre) nominal size) and curing complete, excluding the cost of form work in foundation and plinth/under floors in all depths including pumping or bailing out water/dewatering and removal of slush as required at site complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Random rubble masnory / polygonal rubble masonry (un-coursed / brought to courses) with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (One cement isto six sand isto twelve graded stone agreegate 20 mm (twenty millimetre) nominal size) at plinth level in Cement mortar 1:6 (one cement isto six sand) and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (Three point one five milliMetres)thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five milliMetres) so as to give a fair finish including centering, shuttering, strutting and propping etc, with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling upto any height and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders and lintels, sides and soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels upto any depth/heights, up to all floor level, and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three decimal one five millimetres) thick, welded with angle iron in frame 30x30x5 mm (thirty into thirty into five millimetres) so as to give a fair finish including centering, shuttering, strutting and propping etcetra with wooden battens and ballies, heights of propping and centering in all heights below supporting floor to ceiling upto any height and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors, roofs, landings, shelves, and the like floor, etcetra up to any thickness, up to all floor level, and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Brick work using Second class common burnt clay building bricks in super structure above plinth level upto all heights / floor level in cement mortar 1:6 (one cement isto six sand) and curing complete and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed cement concrete 1:2:4 (one cement isto two sand isto four graded crushed stone aggregate 20 mm (twenly millimetre) nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in suspended floor roofs, landing and shelves and their support balconies, beams, girder, bressumers and centilever up to two floor level and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Providing and laying mild / Tor steel reinforcement for Reinforced Cement Concrete work including bending, binding and placing in position complete including cost of binding wire and other incidentals due for its completion up to all floor level complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Providing and fixing second class deodar wood work in frame of doors, windows, clerestory windows and other frames wrought framed and fixed in position complete and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws 40 mm (forty millimetre) thick 2nd (second) class deodar wood and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 (eighty five) G. with wire of dia 0.56 mm (zero point fifty six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws 40 mm (forty millimetre) thick 2nd (second) class deodar wood and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Steel work welded in built up sections trusses and framed work, composed of beams, joists, channels, angles, tees, flats and connecting plates or angle cleats etcetera as in trusses and trussed purlins, main and cross beams, hip and jack rafters, purlins connected to common rafters and the like in building including cutting, fixing, lifting, hoisting and placing in position complete and applying a priming coat of red lead paint complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing M.S. round holding down or anchor bolts with nuts and washer plates complete and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Providing and fixing 0.60 mm (zero point sixty millimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6 mm (six millimetre) dia metre with prepainted limpet and rubber washers complete with all accesoriees as required aand as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Providing and fixing ridges or hips 60 cm (sixty centimetre) overall with 0.60 mm (zero Point six millimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6 mm (six millimetre) dia and prepainted G.I. limpet and bitumen washers complete with all accessories as required and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Providing and fixing 4 mm (four millimetre) thick plain asbestoscement sheet ceiling of approved quality with butt jointing and wood screws (frame work and cover fillets to be measured and paid for separately) as required and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

20 mm (twenty millimetre) Cement plaster in single coat on rough side of brick / stone masonry for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and / or rounded angles not exceeding 80 mm (eighty millimetre) in girth and finished even and smooth Cement Mortar 1:6 (one Cement isto six sand) as required and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Providing and laying 20 mm (twenty millimetre) thick cement plaster skirting with cement mortor 1:3 (one cement isto three sand) finished with a floating coat of neat cement including rounding of junction with floor in skirting and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Filling in plinth with sand under floors including watering, ramming consolidating and dressing complete as per HPPWD specification and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Providing and laying cement concrete flooring 1:2:4 (one cement isto two sand isto four graded crushed stone aggregate 20 mm (twenly millimetre) nominal size) laid in one layer finished with a floating coat of neat cement and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

White washing with lime on un-decorated wall / celling and or slopping roofs (two or more coats) to give an even shade including thoroughly brooming the surface to remove all dirt, dust, mortar drops and other foreign matter including preparing the surface even and sand papered smooth and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax , GST or any other taxes imposed by the Government.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering and knotting with ready mixed paint brushing wood primer pink and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Painting two or more coats (excluding priming coat) on new wood and wood based surfaces with enamel paint brushing to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering and stoping with enamel paint white or other than white and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing M.S. black plain sheet 1.66 mm to 2.00 mm (one point six six millimetre to two point zero zero millimetres) thick in facia / eaves boards / soffits / ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per HPPWD specifications or as directed by the Engineer-in-Charge, (base members of steel work shall be measured and paid for separately), and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing 40x3mm (forty into three millimetre) flat iron hold fast 40 cm (forty centimetre) long including fixing to frame with 10 mm (ten millimetre) diametre bolts and nuts and wooden plugs and embededding in cement concrete block 30x30x15cm (thirty into thirty into fifteen centimetre) 1:3:6 (one cement isto three sand isto six graded stone aggregate 20 mm (twenty millimetre) nominal size and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 300x16mm (Three hundred into sixteen millimetre) anodized aluminum sliding door bolts anodized transparent or dyed to required colour and shade with necessary bolts, nuts and screws etcetera complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 250x16 mm (Two hundred fifty into sixteen millimetre) anodized aluminum sliding door bolts anodized transparent or dyed to required colour and shade with necessary bolts, nuts and screws etcetera complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 200x10mm (two hundred into ten millimetre) anodized aluminum tower bolts (Barrel type) anodized transparent or dyed to required colour and shade with screws etcetra complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 150x10 mm (one hundred fifty into ten millimetre) anodized aluminum tower bolts (Barrel type) anodized transparent or dyed to required colour and shade with screws etcetra complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 125 mm (one hundred twenty five millimetre aluminium handles) anodized transparent or dyed to required colour and shade with necessary screws etcetra complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing plinth protection 50 mm (fifty millimetre) thick in cement concrete 1:3:6 (one cement isto three sand isto six graded stone aggregate 20 mm (twenty millimetre) nominal size) including finishing the top surface of concrete smooth and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing under layer for plinth protection of 75 mm (Seventy five millimetres) thick (unconsolidated )bed of dry brick / stone aggregate 40 mm (forty millimetres) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Constructing 15 x 22 cm (fifteen into twenty two centimetre) ‘U’ shape open surface drain with square rubble hammer dressed stone masonry side wall in cement mortar 1:6 (one cement isto six sand) and inside platering with cement mortar 1:3 (one cement isto three sand) including earth work and laying 10 cm (ten centiMetres) cement concrete bed in 1:5:10 (one cement isto five sand isto ten graded crushed stone aggregate 40 mm (forty milliMetres) nominal size) and 7.5 cm (seven decimal five centiMetres) cement concrete 1:2:4 (one cement isto two sand isto four graded crushed stone aggregate 20 mm (twenty milliMetres) nominal size) at bottom joint of drain and finished with a floating coat of neat cement complete and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete 1:2:4 (one cement isto two sand isto four graded stone aggregate 40 mm (forty millimetre) nominal size) and curing complete excluding cost of form work in foundation and plinth as per standard design and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Square rubble masonry coursed with hard stone of approved quality in foundation and plinth including racking out joints in cement mortor 1:6 (one cement isto six sand) and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (Three decimal one five millimeters) thick, welded with angle iron in frame 30x30x5 mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etcetra with wooden battens and ballies, heights of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls upto any width, up to all floor level, and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

15 mm (fifteen millimetre) cement plaster in single coat on the rough side of brick / concrete / stone walls for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and / or rounded angles not exceeding 80 mm (eighty millimetre) in girth and finished even and smooth Cement Mortar 1:5 (one Cement isto five Sand) and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing to wall, ceiling and floor ISI marked 15 mm (Fifteen millimeters) nominal bore galvanized mild steel tube (medium grade) tube fittings and clamps of approved brand and manufecture (TATA/JINDAL make) including making good the walls, ceiling and floor, up to all floor levels complete as per HPPWD spectifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and laying 20 mm (twenty millimetre) nominal bore in trenches, galvanised mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 100 mm (one hundred millimetre) nominal size sand cast / cast iron spun spigot and socket soil, waste and ventilating pipes (Lead caulked joints to be measured and paid for separately and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete work 1:2:4 (one Cement isto two Sand isto four graded stone aggregate 20 mm (twenty millimetre) nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in Foundations, footings bases of columns and the like and mass concrete and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete work 1:2:4 (one cement isto two Sand isto four graded stone aggregate 20 mm (twenty millimetre) nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in Walls (any thickness but not less than 0.10 (zero point ten) metre thickness) including attached pilasters buttersses, plinth and string courses etcetra from top of foundation upto floor two level and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30x30x5mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuutering, strutting and propping etcetra with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. (four metres) and removal of the same for insitu-reinforced concrete & plain concrete work in Foundation, footings basis of coloumns etcetra and mass concrete and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing cast iron holder bats including steel bolts to sand cast iron / cast (spun) iron pipes embedded in and including cement concrete blocks 100 mm x 100 x 100 mm (one hundred millimetre into one hundred millimetre into one hundred millimetre) of 1:2:4 mix (one cement isto two sand isto four graded stone aggregate 20 mm (twenty millimetre) nominal size) including cost of cutting holder and making good the walls 100 mm (one hundred millimetre) nominal diameter / size pipe and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing sand cast iron / cast iron spun fittings and accessories Bends of required degree (any radius) with oval access door insertion rubber washer 2 mm (two millimetre) thick, bolts and nuts 100 mm (one hundred millimetre) nominal size and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing sand cast iron / cast iron spun fittings and accessories Bends of required degree (any radius) plain 100 mm (one hundred millimetre) nominal size and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing sand cast iron / cast iron spun fittings and accessories collar 100 mm (one hundred millimetre) nominal size and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing Cast iron cowl 100 mm (one hundred millimetre) nominal diameter and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providng lead caulked joints to sand cast iron cast (sun) iron pipes and fittings including testing of joints 100 mm (one hundred millimetre) nominal size diametre and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing vitreous China wash down, water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1 (one cement isto one sand) (seat and over to be measured and paid for separately) and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closetwith C.P. Brass hinges and rubber buffers white plastic seat and cover and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 10/12.20/15.00 litres vitreous China low level flushing cistern with a pair of C.I. or mild steel brackets, complete with fitting such as lead valve less syphon, 15 mm (fifteen millimetre) nominal size brass ball valve with polythene float, C.P. Brass handle, unions and couplings for connections with inlet, outlet and overflow pipes, 40 mm (forty millimetre) dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing flat back 550 mm x 400 mm (Five hundred fifty into four hundred millimeters) vitreous china wash basin with single hole for pillar tap with CI or MS brackets painted white including cutting holes and making good the same but excluding fitting complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 32 mm (thirty two millimetre) nominal dia metres C.P. Brass chain 50 cm (fifty centimetre) long and rubber plug of following sizes for sink or wash basin and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 32 mm (thirty two millimeters) nominal diameters rubber plug for wash basin or sink (Heavy duty makes ISI marked is No. 8931 7893) and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 32 mm (thirty two millimeters) nominal diameters CP brass waste pipe for wash basin or sink and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 32mm (thirty two millimeters) nominal diameters M.I union for wash basin or sink and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 2 mm (thirty two millimeters) nominal diameters C.P. Brass S. Trap for wash basin and sink and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 600x450mm (Six hundred into four hundred fifty millimeters) bevelled edge mirror of superior glass (atultuff or equivalent make) mounted on 6 mm (Six millimeters) thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washers complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 600x20mm (six hundred into twenty millimeters) C.P. brass towel rail complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 600 mm x 120 mm (six hundred millimetre into one hundred twenty millimetre) glass shelf with C.P Brass bracket and guard rail complete, fixed to wooden plugs with C.P Brass screws and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws complete upto all floor level as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 15 mm (Fifteen millimeters) diameters ISI marked C.P brass bib tap with capstan head complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 15 mm (fifteen millimeters) diameters C.P. brass pillar tap with capstan head, (heavy duty make ISI marked No-8931-8934) and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 15 mm (fifteen millimeters) diameters brass pillar tap with capstan head, (heavy duty make ISI marked No-8931-8934) complete and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing C.P. brass angle valve 15 mm without Nuts and pipe and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing ISI marked 45 cm (forty five centimeters) long and 15 mm (fifteen millimeters) nominal bore PVC connection pipe with brass unions complete as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimeters) nominal bore brass full way valve with wheel complete upto all floor level as per HPPWD specifications and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and placing water tank made of (sintex) having a capacity of 500 ltr. (five hundred liters) each with necessary fiting including over flow pipe etcetra and ballvalve and with cover and locking arrangement including providing pads of sizes as required for in let and out let of good quality in all respect and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Constructing manhole with RCC top slab in 1:2:4 mix in one cement isto two sand isto four graded stone aggregate 20 mm (twenty millimetre) nominal size) foundation concrete1:4:8 (one cement isto four sand isto eight graded stone aggregate 40 mm (forty millimetre) nominal size) inside plastering 15 mm (fifteen millimetre) thick with cement mortar 1:3 (one cement isto three sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (one cement isto two sand isto four graded stone aggregate 20 mm (twenty millimetre) nominal size) finished smooth complete including curing and testing Inside size 800mm x 800 mm (eight hundred millimetre) into eight hundred millimetre) and 500 mm (five hundred millimetre) deep including C.I cover with frame. (Light duty single seal pattern - 1 (one)) 455 mm x 610 mm (four hundred fifty five millimetre into six hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38kg. (thirty eight killograme) (Weight of cover 23 kg (twenty three killograme) and weight of frame 15 kg. (fifteen killograme) With 200 mm (two hundred millimetre) thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (one cement isto three sand) and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing on wall face 100 mm dia (one hundred millimetre) P.V.C. (D-Plast) rain water pipes of working presser not less than 4.5 kg / sqcm (four point five killograme per square centimetre) including fitting the joints with approved adhesive complete and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing on wall faces PVC (D-plast) plain bend 150 mm dia (one hundred fifty millimetre) accessories for rain water pipes including filling the joints approved adhesive complete and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 20 mm (twenty millimetre) nominal dia metre brass stop cock and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing in position water lifting pump (toollu pump) having 1.00 (one) horse power capacity of Kirloskar or equivilent make ISI mark including all necessary fitting required at site complee in all respect and as per the directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidental. The rate including the octroi, royalty, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.