CWE/P-70/2020-21 CERTAIN REPAIR OF ROADS, ROAD BERMS AND ROAD FURNITURE AND SPECIAL REPAIR TO ROAD FROM MAIN GATE TO BACK GATE OF CERTAIN UNIT UNDER AOR OF GE (WEST) PATHANKOT

Amount

Material and labour repair to potholes any depth, not exc 1 sq m each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc .including cutting around edges to at least 25 mm in depth, making good by applying a tack coat using paving bitumen VG-10 @ 5Kg/10 Sqm putting in premix as specified for thin bituminous carpet (30 mm thick) well rammed and sealed with premixed sand seal coat (9.8 Kg per 10 Sq m, blinded with binder, blinded with 0.09 cu m of stone chippings , 6.3 mm size) and again well rammed (including supply of premix macadam, binder and chippings and sand) depth of pot holes exceeding 25 mm using roller 8 to 10 Tonne capacity complete all as specified and directed.

Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area not exceeding 400 sqm, (depth exc 50mm but n.exc. 100mm deep) complete all as specified

Material and labour 75 mm thick (compacted thickness) WBM with coarse aggregates of sand/lime stone, flint or quartzite of grading 2 (63 mm to 40 mm size) spread, rolled, and consolidated to required gradient and camber with power roller 8 to 12 tonne capacity power woller complete all as specified and directed.

All as per Serial item No. 03 here in before but except material complete all as specified and directed.

Material and labour preparing water bound macadam surfaces by brushing with wire brushes for removing caked mud etc sweeping with brooms and finally fanning the cleaned surface with mechanical air compressor to remove all loose dirt etc and applying evenly a priming/tack coat with paving bitumen (VG-10) @ 10 Kg/10 Sqm and provn of bituminous premixed asphaltic semi dense concrete 40mm consolidated thickness using crushed graded stone aggregate mixed with binder content of paving bitumen VG-30 with 5.5% binder contents by weight of total mix by using self propelled mechanical paver, rolled and compacted to required camber and gradient with 8 to 10 Tonne capacity power roller including preparation of bitumen carpet in digital computarized weigh batch hot mix plant, complete all as specified. Note : Contractor shall quote his rates by considering binder content as 5.50% of the total mix by weight. In case of any variation on minus side in the weight of binder as per actual mix design, the same shall be adjusted @ Rs 40 per Kg. and recovery for the same shall be effected from the contractor. However the variation in the weight of bitumen is on plus side, nothing extra shall be paid on this account.

Material and labour Premix bituminous macadam (design mix) with 4% of binder content by weight of total mix using paving bitumen VG-30 laid/ rolled and compacted to required gradient and camber (consolidated thickness 75mm or less) with 8 to 10 Tonne capacity power roller incl preparation of existing surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc., complete all as specified and directed.

Material and labour preparing black top surfaces by brushing with wire brushes for removing caked mud vegitation grass etc, sweeping with brooms and finally fanning the cleaned surface with mechanical air compressor to remove all loose dirt etc and applying evenly a priming/tack coat with bituminous primer using paving bitumen VG-10 @ 5 Kg / 10 Sqm and provn of bituminous premixed asphaltic semi dense concrete 30mm consolidated thickness using crushed graded stone aggregate mixed with binder content of paving bitumen VG-30 with 5.5% binder contents by weight of total mix by using self propelled mechanical paver, rolled and compacted to required camber and gradient with 8 to 10 Tonne capacity power roller including preparation of bitumen carpet in digital computarized weigh batch hot mix plant, complete all as specified. Note : Contractor shall quote his rates by considering binder content as 5.50% of the total mix by weight. In case of any variation on minus side in the weight of binder as per actual mix design, the same shall be adjusted @ Rs 40 per Kg. and recovery for the same shall be effected from the contractor. However the variation in the weight of bitumen is on plus side, nothing extra shall be paid on this account.

M&L Preparing of new/ old black top road surfaces and applying one coat of retro reflective thermoplastic road marking paint 2mm thick for longer durablity with 8% glass beads using special applicator machine with heating arrangement upto 160°C. Paint material shall be conforming to Ministry of surface transport (MOST) specification 803.4 Vol III as laid down in specification of road /bridge work "third revision" complete all as specified and directed Engr-in-charge.

S&F in replacement Factory made Rectro reflective road sign comprising of plates of size 1500 x 900 mm fixed , one above the another made of 2 mm thick aluminum sheet duly framed in stainless steel 40mm bore pipe. The plates fixed with aluminium rivets and written on both side indicating the directions, alphabets, arrow, lines, diagrams etc on each sides with computrised cut letters and signs (reflective) as directed of approiate size and white in colour and dennison HIP base green. The boards (Plates) dully fitted with stainless steel 40 mm bore top height of boards with legs from ground level minmum 2.50m each including embedding in PCC (1:2:4) type B 1 block of size 30 Cm x 30cm x 60 cm including earthwork excavation and taking out old sign board any type all as per sample kept in GE office and as directed by Engr-in-charge (pegged sign board fully reflective). Make : GREEN LIGHT /GREEN /DARK EYE/ENS/ GUNNEBO/SHAKTI.

S&F in replacement Factory made Rectro reflective road sign boards comprising of plates of size 1200 x 800 mm fixed , one above the another made of 2 mm thick aluminum sheet duly framed in stainless steel 40mm bore pipe. The plates fixed with aluminium rivets and written on both side indicating the directions, alphabets, arrow, lines, diagrams etc on each sides with computrised cut letters and signs (reflective) as directed of approiate size and white in colour and dennison HIP base green. The boards (Plates) dully fitted with stainless steel 40 mm bore top height of boards with legs from ground level minmum 2.50m each including embedding in PCC (1:2:4) type B 1 (using 20mm graded crushed stone aggregate) block of size 30 Cm x 30cm x 60 cm including earthwork excavation and taking out old sign board any type all as per sample kept in GE office and as directed by Engr-in-charge (pegged sign board fully reflective). Make : GREEN LIGHT /GREEN /DARK EYE/ENS/ GUNNEBO/SHAKTI.

Supply and fixing dual directional reflective cat eye of aluminium casted stud size 130mm x 130mm having plastic ABS strip, containing 52 mini retro reflective glass beads of colour white, red/yellow a side provided with steel zinc plated nails of dia 12mm of length 120 mm for fixing to road by hammering complete all as specified. Make : Green lite Cat Part No 01-01 CAT-EYE AL 130x 130 (104 Beads)/ GREEN /DARK EYE/ENS/ GUNNEBO/SHAKTI.

S&F in repairs Traffic convex Mirrors body colour black in Polycarbonate/ Stainless steel with Dome size is 30" and 36" in Dia with GI pole of suitable height for ground requirement and necessary excavation, PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) 0.45 x 0.45 x 0.60 metre, location moving & etc as directed by GE. Make : GREEN LIGHT /GREEN /DARK EYE/ENS/ GUNNEBO/SHAKTI / VERTEX.

S&F in repairs yellow and black plastic speed bump made up of ABS materials to highly reflective reflector moulded in EMMA material welded with ABS base plate through ultrasonic welding processes of size 350mm length and width of 263mm with working width of 250mm, height 53mm and weight appx 1200 gram. Make : GREEN LIGHT /GREEN /DARK EYE/ENS/ GUNNEBO/SHAKTI / SAPPHIRE

Preparation of new or previously treated surfaces and painting Kerb stones, dashes, arrows, letters and like exc. 10cm wide with road marking paint as in different tint and narrow width complete all as directed by Engr-n-charge. (Note: Before painting the Kerb stones all the sides, green vegetation and earth deposited shall be cleaned and removed from site like green vegetation, earth deposited if any and sands etc. and rate quoted shall be inclusive of this aspect)

Repair to pot holes any depth not exceeding 1 Sqm each including sweeping free from dust and mud or water scoring sunken surface in roads etc cutting around edges to at least 25 mm in depth, making good by filling in screened and graded road metal watering and well ramming (including supply of road metal) complete all as specified and directed.

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

M/S. RAJESHWAR SINGH.

M/s Randhawa Builders

M/s Walia Construction Co.

RATTAN CHAND CHANDAN AND CO