PROVN OF TOILETS CUM BATHROOM BLOCK NEAR BLDG NO T-10AT LAD AND PROVN OF STORE ROOM FOR DEEP FREEZERS OF CHICKEN MEAT FROZEN AT COY, ASC SPL REPAIR TO BLDG NO T-49 OF LTADR AT BHULUKMARAAND ADD _ALT OF BLDG No-P-5 AT SARAIBARI UNDER GE JORHAT.

Amount

NOTES :(i)The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil

Excavating over area not exceeding 1.5 m deep and getting out in soft/loose soil.

Excavation over area exceeding 1.50 m and not exceeding 3.00 m in depth and getting out in soft/loose soil.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc. or for shafts, wells, cess pits, manholes, pier holes etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out as in soft/loose soil.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level n. exc. 1.50 m above the starting point.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft/loose soil.

Material and labour for Plain Cement Concrete M-7.5(Nominal Mix) using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed.

Material and labour for reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in floor & roof beams complete all as specified and as directed.

Material and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in Chajja complete all as specified and as directed.

Material and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in Columns complete all as specified and as directed.

Material and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in foundation & plinth beams complete all as specified and as directed.

Material and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in slabs supported on walls, beams and Columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Material and labour for Precast Reinforced Cement Concete slab type M-25(Designl Mix) using 20 mm graded stone aggregate, set in Cement Mortar (1:4) complete all as specified and as directed.

Use and Waste of formwork for foundations, foundation beams etc. for rough finished surfaces of concrete complete all as specified and as directed.

Use and waste of formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves for flat surfaces complete all as specified and as directed.

Use and waste of formwork to chajjas and similar items including edges complete all as specified and as directed.

Use and waste of formwork to sides of columns complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slab, floor slabs, landings not exceeding 200 mm thick (horizontal or sloping) for rough finished surfaces of concrete complete all as specified and as directed.

Material and labour for high strength steel TMT bars (Fe 500D) 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.90 mm dia complete all as specified and as directed.

Material and labour for high strength steel TMT bars (Fe 500D) 6 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel (annealed) wire not less than 0.90 mm dia complete all as specified and as directed.

Material and labour for Rolled mild hollow steel sections steel of grade YSt 310 conform to IS 4923-1997 in roof trusses (framed), trussed, purlins, bracing and fastenings including distance pieces, cleats etc complete all as specified and as directed. Note:- The steel trusses shall be provide as per TD no CESZ/STD/26.

Material and labour for mild steel screw bolts (machine made) with hexagonal or square head one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 22.5 cm and not exceeding 30 cm long, dia of neck 16 to 20 mm complete all as specified and as directed

Material and labour for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick and pitch length 75 mm c/c of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Material and labour for pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, tips, valley, gutters, length & girth as fixed with nail or screws complete all as specified and as directed.

Material and labour for mild steel work in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

Material and labour for Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410W (Gde- E- 250) quality- A

Material and labour for old size Brick work with bricks class designation 75, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

Material and labour for old size brick work with bricks class designation 75, size as per old size brick, straight or curved on plan exceeding 6 m mean radius half brick thick walls built in Cement Mortar 1:4 complete all as specified and as directed.

Material and labour for 25 mm thick Plain Cement Concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in Damp proof course to horizontal or vertical surfaces including necessary formwork

Material and labour for Brick work with bricks class designation 75, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:4

Supply only integral liquid water proofing compound

Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, with water proofing treatment complete all as specified and as directed. Note:- Water proofing compound shall be measure and paid separately

Material and labour for Rendering 15 mm in Cement Mortar 1:4 on fair faces of brick work or concrete surfaces finished even and smooth using extra cement complete all as specified and as directed.

Material and labour for Rendering 15 mm in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for PCC 1:2:4 type B-1 using 20mm graded crushed aggregate as in filling in holdfast/ filling in pressed steel frame etc including necessary form work complete all as specified and directed.

Material and labour for Plain Cement Concrete M-10(Nominal Mix) using 20 mm gaded stone aggregate as in Surface channel and drain

Material and labour for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.

Material and labour for Add or deduct for each 25 mm girth or part thereof over or under 30 cm inner girth in cement concrete

Earth filling under floors, spreading and levelling in layers not exceeding 25 cm thick and well ramming including watering as required.

Material and labour for hard core of gauge not exceeding 63 mm of broken stone or boulders , spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

Material and labour for Sand filling under floors or in fdns incl watering and consolidation

Material and labour for 75 mm thick plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in plinth protection or flooring, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for75 mm thick plain cement concrete 7.5 (Nominal Mix) using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

Material & Labour Glazed ceramic tiles 450x350x7 mm(Coloured) on vertical surfaces such as skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete over 10mm thick screed bed vertical layer in CM (1:4)all as specified and as directed.

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.11 Sqm and not exceeding 0.18Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

All as per item No _46 here-in-before but to vertical surfaces such as skirting over and including 10mm thick rendering in CM (1:3) complete

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.11 Sqm and not exceeding 0.18Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

All as per item No _55 here-in-before but to vertical surfaces such as skirting over and including 10mm thick rendering in CM (1:3) complete

Material & Labour Material and labour for outdoor, antiskid, vitrified paving tiles, of size 300mmx300mmx10mm laid in floors, set and jointed in cement mixed with pigment to match tile colour over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

Material and labour for Preparation of new plaster wall surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of complete all as specified and directed.

Material and labour for Preparation of new plaster ceiling surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of complete all as specified and directed.

Material and labour for preparation of new surfaces and and applying 2 coats of cement based paint over a coat of alkali based primer complete all as specified and directed.

Supply and fixing of 35 mm thick flush shutters, solid core construction, with block board core and comercial plywood face panels with one face is covered with decorative face veneer with lipping/frame to match all complete all as specified and as directed.

Material and labour for Solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with Mild Steel square tube, suppling & fixing in opening as per drawing complete all as specified and directed.

Material and labour for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawingcomplete all as specified and directed.

Materials and labour for Mild Steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290(Gde E-165) complete all as specified and as directedincluding taking dwon old one complete all as specified and as directed.

Supply and fixing of pressed steel door frames (fabricated out of CRLCS sheet 1.6 mm thickness) 125 x 60 mm size with one or more rebates including necessary fixing lugs, hinges, lock striking plate etc. complete all as specified and as directed.

Supply and fixing of steel ventilator with top hung shutters including hinges with steel handle and steel peg stay complete without gauged bars, dovetailed or welded complete all as specified and as directed

Supply and fixing of steel windows with side hung shutters including hinges projecting type with steel handle and steel peg stay complete with gauged bars, dovetailed or welded complete all as specified and as directed

Supply and fixing of steel windows with side hung shutters including hinges box type with steel handle and steel peg stay complete without gauged bars, dovetailed or welded complete all as specified and as directed

Supply and fixing of sheet glass 4 mm thick ordinary quality fixed to aluminum window in squares in each pane of required size complete all as specified and as directed.

Supply & Fixing of Glazing with sheet glass (frosted on one side) 4 mm thick ordinary quality with oil putty in square not exceeding 0.5 Sqm in each pane.

Supply & Fixing of Aluminium anodised barrel tower bolts of extruded section size 150 mm complete all as specified and directed.

Supply & Fixing of Aluminium anodised barrel tower bolts of extruded section size 200 mm complete all as specified and directed.

Supply & Fixing of Butt hinges Stainless steel 100 mm size complete all as specified and directed.

Supply & Fixing of Floor door stopper of SS body and tongue, anodised, with hard drawn steel spring of size 150 mm, fixed in floor complete all as specified and directed.

Supply & Fixing of Aluminium handles cast type anodised 150 mm size complete all as specified and directed.

Supply & Fixing of Aluminium anodised sliding door bolt, with hasp & staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long .complete all as specified and as directed.

Supply and fixing of Towel Rail 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed. Make :- Cat no BA-40 of Prayag or equivalent model of make list as given in PS as approved by GE.

Material, labour and fixed of power coated aluminium snap grid frame work for false ceiling, size of grid 605 x 605 mm, including aluminium main/closs tee of size 35mm x 23mm x 1.5 mm ( minimum) aluminum BULBED TEES section and aluminium angle of 25mm X25mm X1.5mm thick, sutiable type GI wire hanging arrangement with adjuster all as specified in clause no 10.38 in SSR part-I and including 6 mm thick high pressure steam cured non asbestos fibre cement designer board as per IS 14862 with applying of two coats of acrylic distemper over a coat of primer complete all as specified and directed. Make (i) ALUMINUM SNAP GRID:- HINDALCO/ INDALCO/ JINDAL (ii) Non Asbestos Fibre Cement Board as per IS 14862:-ARMSTRONG/ SAINT GOBAIN (GYPROC)/EVEREST / VISAKA Industries Ltd

Material and labour for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel and iron surfaces of any description over exceeding 10 cm in width or girth complete all as specified and as directed..

Material and labour for Painting 2 coats of synthetic enamel paint on wooden surfaces of any description over 10 cm in width or girth including preparation new surface and one coat of pink primer complete all as specified and as directed.

Supply and fixing of 15mm bore stop valve angular type cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe for union 15mm complete all as specified and directed.

Supply and fixing of bib cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS -08 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore

Supply and fixing of 15mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed.

Supply and fixing of 20mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed. Note for item no 77 & 78:- All fitting & fixture such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector, holding clamp shall be provide as per site requiredment as as directed by AGE and same shall deem to be included in quoted rate.

Supply and fixing of chromium plated brass glass shelf fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified. Make :- Cat no BEA-47 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of chromium plated pillar cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS 02 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of 125 mm dia of shower rose with 225 mm long arms, cast copper alloy chromium plated , swivel joints and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no BS-76 of PRAYAG or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of Soap dish chrome plated complete all as specified and as directed. complete all as specified. Make :- Cat no BA-05 of PRAYAG or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of stop cock , cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS -28 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of uPVC of type-B for use in soil and waste discharge systems, single socket, 110 mm bore in any length including rubber ring joints and fixed to walls with clips and other standard material and including taking dwon old rain water pipe & removal from site all as specified in IS 13592 complete all as specified and directed.

Supply and fixing of uPVC of type-B for use in soil and waste discharge systems, single socket, 75 mm bore in any length including rubber ring joints and fixed to walls with clips and other standard material and including taking dwon old rain water pipe & removal from site all as specified in IS 13592 complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )bend for 110 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )bend for 75 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )juction equal or unequal for 110 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of PVC(SWR) vent cowl, 110 mm bore

Supply and fixing of PVC(SWR) gully trap 125/110 mm, setting and jointing with solvent cement.

Supply and fixing of PVC (SWR) floor trap, plain with grating including jointing with solvent cement, 75 mm dia of outlet.

Plain Cement Concrete (1:3:6), type C-2 using 40 mm graded stone aggregate as in concrete bed to drain pipes laid to falls in trenches in any depth including packing under, and haunching against the sides of pipes for 110mm bore PVC SWR pipe.

Supply and fixing of PVC SWR, single socket, 110 mm bore in any length including rubber ring joints and fixed to walls with clips and other standard material all as specified in IS 13592.

Supply and fixing of vitreous china wash basin white flat back, size 550 x 400 mm including CP waste coupling,with GI pipe brackets, 32 mm dia PVC corrigated wast pipe & rag bolt in cement concrete/brick wall surface complete all as specified and as directed. Make: Cat no S2040103 wash basin of CERA or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of Gratings made from Stainless steel Gr 304 of doom type & 100mm dia complete all as specified.

Supply and fixing of Vitreous china wash down water closet (pedestal pattern) with concealed S-trap or P-Trap, white, 390 mm high, seat cover including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc acomplete all as specified and as directed Mak:-SLICK of HINWARE or equivalent model of make list as given in PS as approved by GE."

Vitreous china urinal Half Stall type, white with grating, union for discharge pipe, flush pipe, waste pipe and brackets including fixing

Supply and fixing as of PVC low level flusing cistern 10 litres capacity white with ball valve & brackets with flush pipe complete all as specified and as directed. Make: CHIVAS of CERA or equivalent model of make list as given in PS as approved by GE.

Supply and fixing as of PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

Supplying, hoisted and fixed in position of rotational moulded polyethylene water storage tanks in double layers and cylindrical vertical type with manhole lids(closed top) of 1000 litres capacity with ISI marked and all as specified in IS 12701 and including complete all as specified and directed .

Cutting into existing manhole for connecting new drain, making good to pipe & rendering, cutting out existing benching for and forming branch channel (half round or 3/4 section) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate for 150 mm bore pipe

Material and labour for Loose filling with aggregates of gauge 20 mm

Material and labour for Brick work with class designation 75 bricks, old size bricks in one brick thick honey comb walling built in Cement Mortar 1:3

Material and labour for 75 mm thick cement concrete 1:2:4 type B2 using 20 mm graded stone aggregate as in bed finished even and fair.

Demolition of cement concrete (un-reinforced) in ground floors, sunken floor and paving complete all as specified

Dismantling wall and ceiling boards (fibre pulp or insulation etc) any thickness including cover fillet complete all as specified and as directed.

Material and labour for Preparation of old wall surfaces and applying two coat of synthetic enamel paint on steel and iron surfaces of any description exceeding 10 cm girth or width complete all as specified and directed.

Material and labour for Stainless steel wire cloth, 0.43 mm nominal dia of wire and avergae width of aperture 1.00 mm and fixed with stainless steel wire staples complete all as specified and directed.

Material and labour for 50 mm thick plain cement concrete 7.5 (Nominal Mix) using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

Material and labour for 40 mm thick plain cement concrete M-15(Nominal Mix) using 20 mm graded stone aggregate as in floor, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for Preparation of new surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.

Material and labour for complete removal of existing finishing of internal wall surface of building/structure by mechanical appliance and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.

Material and labour for complete removal of existing treatment of external wall surface of building/structure by mechanical appliance and preparation of old surfaces applying two coats of acrylic exterior weather resistant paint(weather proof paint @ 1.67 ltr/10 sqm per two coats ) of required colour shade and as per manufacturer’s specification over a coat of acrylic exterior primer((@ 2.20 kg/10 sqm) complete all as specified and directed.

Material and labour for preparation of new wall surfaces and applying two coats of acrylic exterior weather resistant paint(weather proof paint @ 1.67 ltr/10 sqm per two coats ) of required colour shade and as per manufacturer’s specification over a coat of acrylic exterior primer((@ 2.20 kg/10 sqm) complete all as specified and directed.

Material and labour for power coated anodised aluminium door shutters, aluminium section weighing 1.00 Kg/ m (minimum) thickness not less than 2.00 mm including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, floor hinges, anodised aluminum snap beading screws etc. Complete all as specified and as directed.

Supply and fixing Powder Coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. Including taking down exsiting door/window fream with shutter complete all as specified and directed.

Supply and fixing of tinted glass with sheet glass 5mm thick , pin head type and glazing in squares exc 0.5 sq. M in each pane complete all as specified and as directed.

Material & Labour of vitrified ceramic tiles,double charged dark coloured shade, 10 mm thick of square/rectangular area of each tile not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over 15mm thick screed bed layer in CM (1:4)complete all as specified and as directed.

Material & Labour of vitrified ceramic tiles,double charged dark coloured shade, 10 mm thick of square/rectangular area of each tile not exceeding 0.36 Sqm, as in skirting etc. set and jointed in neat cement slurry and pointed in coloured cement to match over 10mm thick screed bed layer in CM (1:4)complete all as specified and as directed.

Material & Labour of vitrified ceramic tiles,double charged dark coloured shade, 10 mm thick of square/rectangular area of each tile not exceeding 0.36 Sqm, as in skirting etc. set and jointed in neat cement slurry and pointed in coloured cement to match over 10mm thick screed bed layer in CM (1:4)complete all as specified and as directed.

Material and labour for 25 mm thick plain cement concrete M-15(Nominal Mix) using 12.5mm graded stone aggregate as in floor, finished even and smooth without using extra cement complete all as specified and as directed.

Material & Labour of 18mm thick granite ( of any type) work ( table rubbed and polished in pillars and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust admixture of pigment to match with shade of granite over 15mm thick screed bed layer in CM (1:4) including taking down existing one complete all as specified and as directed.

Material and labour for solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing on vertical PVC fillet frame all as per specified on page no 162 of SSR Part-II complete all as specified and directed.

Material and labour for 5mm thick PVC sheet fillet frame of width 35mm for wall paneling and fixing on to wall to make PVC Frame all as per specified on page no 162 of SSR Part-II complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and rubbish off the MOD premises complete all as specified and as directed.

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. not exceeding 1.50 Sqm each complete all as specified and as directed.

Supply and fixing of aluminium sliding window with powder coating (minimum thickness of powder coating 50 micron) including following components / specifications complete all as specified and as directed. (i) Two leaf glazed sliding shutter and one leaf gauged (fly proofing) sliding shutter. (ii) Opening of windows exceeding 0.90 Sqm but not exceeding 1.50 Sqm (iii) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (iv) All vertical/ horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, etc. (vi) Rest all as specified in drawing no CESZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5 & 5R/5. Note Nos :- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall be deem to included quoted rate. Only measure opening size of window. (ii) Only Glass wire mesh shall be measure and paid separately under relevant items of BOQ .

Supply and fixing of aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum thickness of powder coating 50 micron) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge.

Material and labour for 18/19 mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

Supply and fixing of Aluminium extruded section body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

Supply and fixing of Factory made solid PVC Moulded Door Shutter, 28 to 30 mm thick (stiles), 2,4, or 6 raised panel design with 2 mm thick Moulded prelam PVC sheet on the front face and 2 mm plain colour prelam PVC sheet on back face with particle board core complete all as specified and directed.

Supply and fixing in repairof Towel Rail 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed. Make :- Cat no BA-40 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of PVC ball valve for 20 mm dia GI pipe all complete complete all as specified and directed.

Material and labour for Rolled mild steel of grade Fe-410-W (Gde E-250) (quality A) of Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated)

Dismantling water tanks of capacity exceeding 250 litres but not exceeding 500 litres including float valve and removing from site complete all as specified and as directed.

Taking up or down 15mm dia steel tubing and connections, including cleaning for refixing or removal to store.

Taking up or down 20mm dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down rain water pipe complete all as specified and directed.

Subtotal of Sch A part-I

SCHEDULE 'A' PART - II FOR B/R PORTION (Sl No __ to ____)

Taking down carefully unserviceable copper / aluminium point wiring (light, fan, bell socket or power) including all fittings such as switches, socket, ceiling roses , regulators and switch boxes etc complete and making good the disturbed surfaces complete all as specified and as directed.

Material and labour for concealed point wiring complete with 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable 1100 volt grade, FRLSH through and including 20 mm PVC conduit & its accessories, cadmium screws fixed in concealed surface of wall/ceiling/false ceiling and including 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable FRLSH as earth continuity conductor and MS boxes made of 16 gauge MS sheet concealed type on walls cover 3mm thick laminated sheet for housing complete switch for One light/fan/bell point controlled by one way switch. Note :- Cutting chases and making good in walls shall be deemed to be included in the unit rate.

All as per item no 142 here-in-above but One 3 pin socket outlet 5 amps on the same board with other switches

All as per item no 142 here-in-above but above but for one 5 amp socket independent complete all as specified and as directed.

Material and labour for concealed point wiring complete with 2.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable 1100 volt grade, FRLSH through and including 20 mm PVC conduit & its accessories, cadmium screws fixed in concealed surface of wall/ceiling/false ceiling and including 2.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable FRLSH as earth continuity conductor and MS boxes made of 16 gauge MS sheet concealed type on walls cover 3mm thick laminated sheet for housing 3 pin socket outlet 15 Amp independent:- Note :- Cutting chases and making good in walls shall be deemed to be included in the unit rate.

Supply and fixing of switch piano flush single pole one way 5 amps complete all as specified and as directed.

Supply and fixing switch socket outlet multipurpose 3 pin 15 Amps /5 Amps controlled by one switch.

Supply and fixing switch socket outlet multipurpose 3 pin 5 Amps /5 Amps controlled by one switch.

Material and labour for Electronic type fan regulator step type 120 watt, 230 volt complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 65x50mm three terminals complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and necessary connecting PVC insulated Flexible cable for connection from ceiling rose to fan and connecting complete all as specified.

Supply and Fixing exhust fan 240V, 300mm sweep, 900 RPM , MS body, highly efficient heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings and conforming to IS: 2312 and including aluminium lowers and shutters fixed to wall , writing the MES fan numbers with paint and 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed. Make: Model- Turbo Heavy Duty of USHA/ EXHD-300-6 of CROMPTON GREAVES/Turboforce of Havells or equivalent model of BAJAJ/ORIENT as approved.

Material and labour for lamp holder insulated body with back plate for batten fittings with 10 Watt LED lamps complete all as directed

Supply and fixing of LED surface/ceiling mounting(suspended from ceiling) box type light fitting 20Watt with LED Lamp , drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover & high power LED’s as light source with 120 Lumen per watt (Minimum) and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up three core1.00sq. mm copper conductor flexible wire/cable complete all as specified. Make : Model No BCLAB 20W WH LED P of BAJAJ or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of sheet metal enclosure for MCBs to be used singal pole & nutral double door 8 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length and including taking out old DB complete all as specified and as directed.

Supply and fixing of MCB SP of rating 6 to 32 Amps 240 V complete all as specified and as directed.

Supply and fixing MCB DP 40 to 63 amps 415 volts 10KA breaking capacity.

Supply & Fixing of LED street light fitting ( Building Security light) of 30Watt with LED lamp’s & driver and made of pressure die-cast aluminum housing, IP 65/IP 66 road way luminaries with UV stabilized polycarbonate cover or toughen glass cover & high power LED’s as light source with 110 Lumen per watt and electronic driver with efficiency > 85% . The light fitting shall be fixed on wall/pole with and including 25 mm dia( or higher size as per manufacturers recommendation) light grade GI pipe (bend to shape or as per manufacturers recommendation ) bracket 1.5 mtr long complete with MS flat iron clamp (clamps shall be 40 x 5 mm MS flat) nuts, bolts & washers including painting the clamps with two coat of aluminium paint over a coat of red oxide primer and including taking up old light fitting complete all as specified and as directed Make:- Model No- LSTM-30-CDL M of Crompton Greave or equivalent model of make list as given in PS as approved by GE. Note : (i) Warranty of complete LED luminaries fitting shall not less than four years and Life expectancy of LED's minimum 50,000 burning hrs,. (ii)The contractor shall be submitted the LM-79 third party NABL accredited lab test report and LM-80 test certificate and LED has to be stractured in the same sequence.

Material and labour for Earthing as in repair complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connetced with earthing wire 4.0mm dia as earthing lead by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 15 mm bore (medium grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost.

Supply & Fixing of 3 layered (outer green coloured UV stabilized, middle black coloured UV stabilized and innermost layer white coloured with antimircrobial property) fusion swelded PP-R (polypropylene Random Co -Polymer) concealed pipes 20 mm outer dia, ISI marked and fittings including plain PP-R fittings and brass threaded PP-R fittings and clamping, cutting and making good to the damages of grade PN-16, SDR - 7.4 including laid on ground or wall surface.

Supply & Fixing of 3 layered (outer green coloured UV stabilized, middle black coloured UV stabilized and innermost layer white coloured with antimircrobial property) fusion welded PP-R (polypropylene Randocm Co -Polymer) gate valve (brass insert as pre requirement of the site with handle, screwed both ends for PP-R pipes or for unions fixed of grade PN-25, SDR - 7.4 and size 20 mm light weight complete all as specified and directed.

Material and labour for cutting existing GI pipes 100 mm dia for insertion of new Tee 100X100X25 mm incl Tee for branch connection all as specified and directed.

Material and labour for Sand cushioning to the full width of trenches for protection of cables including punning down complete all as specified. Note :- Thickness of sand cushioning shall be the thickness after punning down.

Material and labour for laying of Class designation 75 bricks, old size, flat, common clay laid in trenches across the trench as cable protection complete all as specified and directed.

Material and labour for laying of LT XLPE insulated armoured heavy duty cable 1100 volt grade ISI marked with alumimium conductor multi strand cross sectional area 16 Sqmm x 2 Core complete all as specified and directed.

Supply and fixing bell push flush type 5 Amps complete all as specified and as directed.

Supply and fixing call bell, ding dong AC 230 volt single pole (ding dong type).

Supply , Fixing & testing of Recessed/Surface LED ceiling light fitting 36 Watt of 600mm x 600 mm with LED lamp’s & driver and made of Metallic CRCA powder coated body with UV stabilized polycarbonate cover or toughen glass cover & high power LED’s as light source with LED fitting system lumen not less than 100% Lumen per watt and electronic driver with efficiency > 85% with inbuilt protection against lightning, over voltage, short circuit and surge/spike protection upto 5 KV ensuring longer life (THD <10%, PF shall be > 0.95, colour temperature 5700±300 K), Life expectancy of LED's minimum 50,000 burning hrs, warranty of complete luminaries fitting shall not less than three years. The fitting shall be tested LM 79 & 80 and test certificate shall be submitted from original manufacture including connection complete all as specified and directeddirected. Make : Model NoLCTLRP 24 FOCDL of Crompton Greaves or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of LED surface/ceiling mounting(suspended from ceiling) box type light fitting 10Watt with LED Lamp , drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover & high power LED’s as light source with 110 Lumen per watt (Minimum) and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up three core1.00sq. mm copper conductor flexible wire/cable complete all as specified. Make : Model No LDL-10-CDL of Crompton or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of sub main wiring with two single core 4.0sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in PVC conduit and accessories accessories including one single core 4.0sqmm copper conductor cable FRLSH as earth wire and including taking out old sub-main wiring complete all as specified and as directed. NOTE:- (a) All runs of copper conductor and one run of conduit shall be measured as one run length.

Supply and fixing of sub main wiring with two single core 6.0sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in PVC conduit and accessories accessories including one single core 6.0sqmm copper conductor cable FRLSH as earth wire and including taking out old sub-main wiring complete all as specified and as directed. NOTE:- (a) All runs of copper conductor and one run of conduit shall be measured as one run length.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

M/S GOPAL ROY AND CO