REPAIR AND MAINT TO RCC CHAJJA COLUMN BEAM CEILING AND FLOORING AND THE CONNECTED WORKS AT AGE BR 1 UNDER GE AF TECH AREA AT AF STN AGRA

Amount

Taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, Including removal of debries out side MD land complete all as specified and directed.

M&L for rendering 15mm thick on fair faces brick or concrete surfaces of walll in CM (1:6) finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for preparation of new surfaces of wall applying with roller two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work/concrete surfaces of wall finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of exterior emulsion paint with one coat of primer in normal / camouflage pattern as per manufacturers instructions etc complete all as specified and directed by Engr-in-charge. Note:- finishing coat shall be applied through roller only.

M&L for rendering 10mm thick in CM (1:3) on ceiling surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L gunniting to RCC works in column ,beams,chhajja, slabs, landing, balconies etc by removing loose concrete including plaster, cleaning of surfaces with wire brushes and applying epoxy, paint anti corrosive coating of minimum 40-50 microns thick to rusted steel reinforcement after removing/ cleaning all rust by sand/grit blasting and supply and fixing welded steel wire mesh of size 75mm x 75mm with 3mm dia steel wire as facies/drops and similar works etc and applying suitable bonding materials (epoxy based or other equivalent i.e Sikadur 32 of Sika NHO EP of Fosroc or equivalent mixed @2% by weight of cement ( as per manufacturers instructions) against treatment to be applied on old concrete surface to bond old and new concrete and providing gunniting with a minimum pressure of 2.5 Kg/sqcm and applying 25mm thick layers of gunniting plaster in cement mortar (1:2) using ordinary port land cement of 43 grade complete all as specified and directed. Note:- The quoted rates shall be deemed the following:- (i) After placing the additionnal reinforcement, all concrete surface shall be throughly scrubbed down with brush, washed with water and allow dry and apply plaster complete all as specified. (ii) Work to be carried out as in patches as directed by Engr-in-charge. (iii) Necessary scaffolding required for,15mm thick plaster in CM 1:4 and TMT bars (where applicable) and preparation of surface and applying two coat of OBD with one coat of primer over 1mm thick wall care putty.

M&L for prepration of new plastered ceiling surfaces and applying three coat of white wash etc complete all as specified and directed

M & L for preparation of old decorated surfaces of walls (plastered or unplastered) and cornices, by brooming down , scrapping down smoke soot, moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of white wash on walls complete all as specified and directed.

M & L for preparation of old decorated surfaces of ceiling (plastered or unplastered) and cornices, by brooming down , scrapping down smoke soot, moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of white wash on ceiling complete all as specified and directed.

Complete removal of existing treatment on wall/roof projections including facia,cornices etc by scrapping with mechanical sander(having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust,loose paint etc by skilled labour complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls and applying two coats of distemper oil emulsion white or tinted with roller, complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls and applying one coat of distemper oil emulsion white or tinted with roller, complete all as specified and directed.

M&L for preparation of old plastered surfaces of Ceiling and applying one coat of distemper oil emulsion white or tinted, complete all as specified and directed.

M&L for providing & applying average 1mm thick of Birla/ JK wall care putty over prepared surface of old wall and ceiling to achieve the surface even and smooth for painting, complete all as specified and as directed

Demolition of cement concrete in ground floor and paving n.exc 15 cm thickness (below or above ground) including floor tiles etc complete all as specified and directed.

M&L for 100mm thick PCC(1:3:6) type C2 using 40mm graded stone aggregate as in sub base of floor etc complete as specified and directed.

Demolition of cement concrete in ground floor and paving exc 15 cm thickness (below or above ground) including floor tiles etc complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block of approved shape and size of 60mm thickness,with minimum compressive strength of 35N/sqmm (M-35 grade) without correction factor for chamfering,made in rubber moulds with 0.50mm thick scratch proof lacquer coating on top surface,with white cement and pigment complete all as specified and directed.

M&L for sand cushioning laid dry to the profile under interlocking block complete all as specified and as directed.

M&Lfor outdoor coloured vitrified paving tiles ,textured surfaces with high skid resistance ,scratch resistance,impact resistant,joint free(edge cut) of size 300mm x 300mm x 8-10mm thick as in floor etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6,set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete all as specified and directed..

M&L 20-25mm thick plastic coated coloured chequered tiles,area of each tile exc 0.05sqm but n.exc 0.09sqm with and incl 20mm thick screed bed in CM (1:6) of approved colour and pointing with grey cement and pigment complete all as specified and directed.

M&L for 25mm thick PCC(1:2:4) type B0 using 12.5mm graded stone aggregate as in sub base of floor etc complete all as specified and directed.

M&L for 8-10 mm thick vitrified ceramic tiles, light shade double charged (square/recangular) area of each tile n exceeding 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of 15 mm thick in CM (1:6) for laying floor finishes complete all as specified and directed

Demolition of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards any thickness and in any position including cover fillets complete all as specified and as directed.

M&L for solid PVC wall lining consisting of 5.00mm thick single side prelaminated PVC sheet inclusive of insolvent cement and fixing at site on PVC frame complete all as specified and as directed . Note:-Rate quoted deemed to be included the cost of taking down existing switch board/tube light etc and fixing the same after fixing of PVC wall lining.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame complete all as specified and as directed

S&F PVC beading fix with adhesive paste all as per manufacturer's instructions complete all as specified and as directed

M&L for hollow PVC wall profile for wall panelling colour/shade as approved size 250mm wide, 8mm over all thick with 1mm wall thickness fixed with stainless steel screw, fixed to walls / ceiling, complete all as specified and as directed by EIC.

S&F anodised aluminium snap grid of size 605 X 605 mm frame work using sutiable size of section for false ceiling to receive non-asbestos fibre cement building board of approved make and design all as specified and directed

S&F 4 mm thick non asbestos fibre cement building board of approved make Design ,fixed or laid/ inserted to aluminium framework with screws as per manufacturer's instructions complete all as specified and as directed.

M & L for repairs to false ceiling board and straightening of aluminium snap grid of any size complete all as specified and directed

M&L for preparation of old surfaces and applying One coats of exterior emulsion paint in normal / camouflage pattern as per manufacturers instructions etc complete all as specified and directed by Engr-in-charge. Note:- The quoted rates shall be deemed the following (i) Primer and emulsion to be carried out through air less spray machine (Mechanical means).(ii) Repair of pot holes, cracks and undulation in surface with wall care putty as required. Note:- The work covered under Sl item No 1 to 33 are to be carried out upto 25.00m height with necessary MS Scaffolding including all other safety precautions. In the quoted rates for Sl item No 1 to 33 the contractor shall be deemed to be included this provision also.

B K Construction Company

deva engineers

C P Singh and Co

Abhi Construction

M/s K S Builders

M/s M S Sharma and Co.

MUKTA AND COMPANY