Proposed Development and Construction of Municipal Holiday Homes Tribal Thematic Resort at Jawhar Municipal, In Reservation No-17 Taluka Jawhar, District Palghar.

Amount

Excavation for foundation in earth, soil of all types. sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling , ramming, water ing including shoring and strutting etc. complete. (Lift upto 1.5 m.)

Exavation for foundation in hard murum including removing the excavated material upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m).

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper.

Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layers including watering and compacting etc. complete

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc.complete.

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete

Providing uncoursed rubble stone masonry of trap/ granite/ quartzite/ gneiss metal in CM 1:5 for plinth joints, scaffolding and watering etc. complete.

Providing and laying CC cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC without SCADA enabled reversible Orum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With natural sandN.S.I. quality Artificial Sand.

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap /granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork,cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for R.C.C. chajja lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and fixing in position TMT -FE-500- bar reinforcement of various diameters for R.C.C pile caps, footings, foundation, slabs,beams, colums, canopies, staircase, newels, chajjas, lintels, pardis, coping, fins, arches etc. as per detailed esigns, drawings and shedules,including cutting, bending, hooking the bar, binding with wires or tack welding and supporting as required complete.

Providing and fixing during laying in RCC Slab rectangular 2 mm thick M.S. sheet fan hook box of size 180x100 mm with required depth with holes or notches as required, bottom and top sides of 1.6 mm M.S. sheet fixed with 3.5 mm dia. round headed screws together with 12 mm dia. M.S. bar bent to shape with hooked ends for fan hook and painting to exposed surface.

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer inC.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete .

Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @m 1Kilogram/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete.

Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete.

Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete

Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete.

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:3 without neeru finish to concrete or brick surfaces, in all position including scaffolding and curing etc. complete.

Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) (As directed by Engineer in Charge)

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Providing neeru finish to plastered surfaces in all positions including scaffolding and curing etc. complete.

Providing and laying vitrified mirror I glossy finish tiles decorative type having size 590 mm to 605mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc.complete. a) Flooring

Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete

Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.

Providing and laying machine cut machine Polished Kota stone flooring 25mm to 30mm thick and required width in plain/ diamond pattern on bed of 1:6 C. M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete

Providing and laying machine cut machine polished machine cut Kota stone slabs 20 to 25 mm thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete.

Providing and laying ceramic tiles having size 30 cm. x 45 cm. confirming to corresponding l.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.

Providing and laying machine cut machine polished shahabad Stone slabs 20 to 25mm thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete

Providing and fixing factory made door/Window frames of required colour made with wood Polymer composite (WPC) extuded internal ribbed sections conforming to American Society for testing and materials (ASTM) in regard with density, tensile strength, flexural strength, Izod impact, water absorption and screw withdrawal strength with wall thickness of 5mm (+/1mm) and with frames having mitred joints at each corner, joined together by two nos. of 10 x 8 mm & 40 mm long PVC dovetail keys including hard wood piece support along the full vertical and horizontal length in rebate portion hole for fixing hinges and fixtures and the frames fixed to Walls/columns with 15 mm long dash fasteners/holdfasts (dash fasteners/holdfasts to be paid separately) etc. complete as per the direction of Engineer in charge,with prior approval of concerned Superitending Engineer

Providing and fixing green marble of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing / moulding the sharp edges wherever necessary, curing, etc. complete

Providing and fixing solid core flush door shutter commercial in single leaf 32 mm thick without ventilator commercial type of exterior grade as per detailed drawings with wrought iron hold fast, stainless steel fixtures and fastenings and handles on both sides and finishing with oil painting 3 coats complete.

Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete.

Providing and fixing fiber glass reinforced polyster door shutter 30 mm thick as per IS 14856 (2000) (Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc

Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/One Running Metre. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 Kilogram/One Running Metre.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/One Running Metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising with box162.

Providing and fixing in position aluminium openable window of any size as per detailed drawing and as directed by Engineer in charge with all necessary aluminum sections including necessary fixtures and fastening with 5 mm thick clear float glass etc. complete. a) With colour anodizing Note While arriving at the rate of item of item weight at 6.90 Kilogram/Square Metre is considered.

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete

Providing and applying washable oil-bound distemper of approved colour and shade to old and new surfaces in two coats including scaffolding, preparing the surfaces. (excluding the primer coat.) etc. complete.

Providing and applying interior wall finish luster of approved make on internal wall surface as detailed below Scrapping the surface with emery paper and wipe clean wall primer with brush with mineral turpentine with brush 8 to 10% and oil 15 to 20% with roller and allowing to dry for a period 6 to 8 hours. wall putty with appropriate proportion of water allowing to dry for period 4 to 6 hours. Scrapping with Emery paper 180 and wipe clean. Applyingwall primer with brush with mineral turpentine 8 to 10% and oil 15 to 20% with roller Scrapping Emery paper 320 and wipe clean, interior wall finish luster 1st coat with brush/rubber/spray with mineral turpentine 7 to 9% and Oil with roller 19 to 21% After 8 hours of activity Applying 2nd coat or wall finish Lustre with mineral turpentine 7 to 9 % with brush and Oil with roller 19 to 21% after allowing dry for the period of 6 to 8 hours activity. (With prior approval of S.E)

Providing and applying two coats of textured synthetic paint of approved shade and quality and one coat of primer before applying textured paint including scaffolding if necessary preparing surface by thoroughly cleaning oil, grease, dirt and other materials as required, etc. complete.

Providing and applying gypsum plaster ( with Gypsum material ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface (Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete

Providing and fixing mild steel grill gate with angle iron frame 65mm x 65mm x 10mm with iron bars at 150mm C/C and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coats of approved shade Weight of gate 35 Kilogram/Smt

Procurement, Supply, Fabrication, Erection, Installation (upto 20kms lead within city limits) of required height Sign Board to have a clear and legible visibility, made with 100mm x 50mmx 5mm thick Channel Section, cross bracing in Angle section of size 35mm x 35mm x 5mm (wherever required) and EPS panels of thickness 75mm. The base will be grouted with a M20 grade Plain Cement concrete foundation of size 600mm x 600mm x 750mm etc (Complete of final size of visible area 08 ft Vertical X( 5ft horizontal X 4ft vertical) EPS panel

Lowering down the debris obtained from breaking and removing the cement plaster / burnt brick masonry of the first floor by any means without causing dust nuisance and damage to structure, stacking the same as and where directed including cleaning the site complete.

Providing ,fixing & concealing Domestic & Flushing water supply in wall including labour for following sizes of C-PVC SDR 11 class pipes with C-PVC fittings, hydraulic testing as per IS including a layer of plaster of Paris with chicken mesh for protection line, making holes & making good the damages by bringing them to good original condition & complete in all respect. Colour codes to be followed as per direction of Architect / Consultant (Toilet & Kitchen internal concealed Domestic water line) 15 mm dia.( N.B of pipe )

20 mm dia.( N.B of pipe )

25 mm dia.( N.B of pipe )

32 mm dia. (N.B of pipe)

40 mm dia. (N.B of pipe)

50 mm dia. (N.B of pipe)

Providing and fixing screw down wheeled stop tap of brass including necessary sockets/union nut complete. (Toilet & Kitchen internal concealed water supply line) 15mm dia.

20mm dia.

25mm dia.

Providing & fixing including labour for following sizes of ASTM - D 1785 SCH 40 (Light Duty) U-PVC pipe with fittings like sockets, union, nuts, elbows, bends, reducers, plugs & T's etc. with solution jointing complete, including supply of clamps, nails etc. making holes in brickwalls and making good the damages by bringing them to original condition and complete in all respects as directed by the Architect. Fittings in schedule 40 conforming to ASTM D 2466. Internal Hydraulic pressure testing as per IS12235. Pasting radium Colour band near Valve, Colour text, flow direction arrow on pipe line at every 5 Mtr. Also including hydraulic testing for 2 hrs at 10 bar. The cost also include supports to the line.The rate shall include the cost of galvanized U clamps, bolts & nuts,supports with 2 coats of zinc chromate primer with 2 coats of enamel paint of total DFT minimum 100 micron. (For water supply terrace loop & vertical downtakes in ducts) 15mm dia.( N.B. of pipe)

20mm dia.( N.B. of pipe)

25mm dia.( N.B. of pipe)

32 mm dia.( N.B. of pipe)

40 mm dia.( N.B. of pipe)

50 mm dia.( N.B. of pipe)

65 mm dia.( N.B. of pipe)

80 mm dia.( N.B. of pipe)

100 mm dia.( N.B. of pipe)

150 mm dia.( N.B. of pipe)

Providing and fixing screw down wheeled stop tap of brass including necessary sockets/union nut complete. (For water supply terrace loop & vertical downtakes in ducts) 25mm dia.

32 mm dia.

40 mm dia.

50 mm dia.

Providing and fixing Butterfly valve ISI marked, CI body including flanges / union, nuts, bolts, washer etc., complete as required. All valves shall be PN10 pressure rated. (For water supply terrace loop & vertical downtakes in ducts) 100 mm dia.

Providing & fixing of Pressure Reducing Brass Valve (PRV) with filter of PN 10 pressure rating, with required flanges, bolts etc. with pressure setting complete as required. (For water supply downtake pipes) 25mm dia.( N.B. of pipe)

32 mm dia.( N.B. of pipe)

40 mm dia.( N.B. of pipe)

Providing and fixing uPVC SWR Type B Pipe laid in floor & fixed on exposed faces of walls / ceiling etc., with necessary cutting to the required length including short pieces Assorted fittings such as Plug/Plain Tee and bend single / double Y, Offsets etc. jointing with solvent and giving water tightness test for the pipes laid in the sunken/ceiling suspended portion with making holes in brick walls/floor grooving & redoing the same and brick support whenever required necessary etc. complete. (Toilet & Kitchen internal waste & soil pipe) 75 mm

Providing & fixing in position Rigid PVC self fit pipes confirming to IS13989/84.waste pipe. Pipes laid in floor and fixed on exposed faces of walls / ceilings etc. in shortlengths for wash hand basin /kitchen sinks to Nahani trap with required size of assorted fittings such as Plug /PlainTee and PVC fittings with materials & labour etc complete, jointing with Finolex make solvent cement solution.Giving watertightness test for pipes laid in the sunken portion with making holes in walls/ floor grooving & redoing the same and support wherever required necessary etc.complete. 50 mm dia. (For WHB & Sink)

Providing and fixing in position PVC Multi floor 50 mm deep seal trap 110x75x50/40 for embedded areas. Making proper connection with cement solvent joints, cutting chase / hole / core cut in floors / slabs and bringing the same in proper condition and shape after placing the trap in right position complete as required.

Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7mm confirming to I.S.13592-1992 including proper rainwater receivingrecess with P.V.C. plug, bend , necessaryfittings , suchas , offsets ,shoes ,inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. ormasonry blocks, includin gnecessary scaffolding and maintenance for 3yrs for any leakages or dislocations of pipes. Allthe P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.(For Rain Water Downtakes) 75 mm

Providing and fixing European type glazed earthenware water closet pan floor mounted + flush tank + Angle cock & health faucet with UPVC seat and lid with chromium plated brass hinges and rubber buffers including UPVC and vent pipe upto the outside face of wall 10 liter enameled low level flushing cistern with fittings pipe stop tap brackets for fixing cistern 32mm dia. UPVC flush pipe with fittings and clamps, 20mm dia. UPVC overflow pipe, mosquito proof couplings G.I. chain and pulley, with water Jet and fitting including cutting and making good to the walls and floors testing etc. complete. (prior approval of sample and brand by MHDC is necessary before use)

Providing and fixing white glazed earthenware Wash Hand Basin including cold water pillar tap, brackets, rubber plugs and brass chain, stop tap and necessary pipe connection including P.V.C. waste pipe and trap upto the outside face of the wall. Making good the damaged surface, testing etc. complete. (prior approval of sample and brand by MHDC is necessary before use)

Fixing, testing and commissioning of approved stainless steel sink Single bowl including wall mounted concealed stop cock with sink spout, flexible drain pipe, rubber adaptor, wall flange, union, C.P. brass chain rubber plug, including cutting and making good the wall / floors wherever required. complete. (prior approval of sample and brand by MHDC is necessary before use) CAT No. Particular Make As approved SS sink As approved

As approved Sink Cock As approved

Fixing, testing and commissioning of approved make C.P. angular stop cock, with C.P. wall flange etc., complete. (prior approval of sample and brand by MHDC is necessary before use) CAT No. Particular Make As approved Angular Stop Cock As approved

Fixing, testing and commissioning of approved make C.P. Bib cock for washing machine & wall flange including C.P. wall flange etc., complete. (prior approval of sample and brand by MHDC is necessary before use) CAT No. Particular Make As approved Bib Cock As approved

Providing and fixing Shower Head, with shower arm of approved make, mixer of including all necessary pipe fittings and connections etc. complete as directed by Engineer in charge. (prior approval of sample and brand by MHDC is necessary before use) CAT No. Particular Make As approved Shower head, Shower Arm, Mixer As approved

Providing, lowering & laying including supply of materials and labour for RCC NP2 class (HUME) pipe of approved make including jointing with collars with hemp yarn, hot bitumen,sand, cement mortor (1:1), curing etc.complete including giving satisfactory water leak proof test & works to be executed as per IS complete as per the direction of project engineer. 150 mm dia.

200 mm dia.

Providing and constructing stoneware Gully traps of size 150 x 100mm in BBM chamber of size 300 x 300 & cement concrete M15, chamber is smooth finishing from inside & outside with CM 1:3 including C.I.grating over the gully trap weight of cover to be 7 kg.

450 x 900 mm ( Medium duty - 140 Kg_ 10 Ton )

Providing, Lowering & laying jointing stoneware glazed pipes (connecting from gully trap to chamber) of the best salt glazed variety to a designed gradient and alignment by site rails and boning roads for proper levelling and making the joints water-tight by providing cement mortor 1:1 joints hemp yarn.curing etc.complete as per IS and as per the direction of Architect. 100 mm dia

All U/G drainage pipes laid in soil shall be supported on 150 mm thk. PCC M-15 supports. Soil below the pipes shall be compacted up to 95% of proctor density.

Excavating trenches of required width in soil for Sewage drainage pipes , including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 Mtrs including getting out the excavated soil and then returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed within a lead of 250 mtrs.Dewatering if required during excavation to be included in the rate.

Providing, lowering & laying including supply of materials and labour for RCC NP2 class (HUME) pipe of approved make including jointing with collars with hemp yarn, hot bitumen,sand, cement mortor (1:1), curing etc.complete including giving satisfactory water leak proof test & works to be executed as per IS complete as per the direction of project engineer. 150 mm dia

200 mm dia.

300 mm dia.

Providing and constructing Brick Masonry Inspection Chamber 90cmx45cm With R.C.C.raft in B.C. soil area including cost of reinforcement, 1:2:4 cement concrete channel shal fround G.S.W. pipes, Brick Masonry, plastering from inside and air tight with 75mm thick R.C.C. cover medium duty 140Kilogrametc. complete. 900 X 450 mm ( Medium Duty cover 140 Kg_ 10 Ton )

Providing and constructing recharge pit of 2.0 m deep and1.0 m dia of pre-cast RCC rings with 6.5" dia x 25m deep borewell at the floor of recharge pit including installation of combination of solid / perforated PVC casing pipe wrapped around with netlon mesh including 300 mm thick side filling around outside of RCC rings (annular space) with 40 mm size boulders including filling of recharge pit upto 0.5m depth with 25 -75 mm clean washed gravels from bottom up followed by 0.5m depth of 10 -25 mm of clean washed stones followed by 0.5m of washed river fine aggregate (natural sand / crushed sand VSI grade finely washed etc.) including netlon mesh between each gravel / fine aggregate (natural sand / crushed sand VSI grade finely washed etc.) media layer including covering with RCC slab, manhole frame & cover, PVC rungs, PVC end -caps, fittings etc. including arrangement for inlet & outlet pipe excavation & backfilling as shown in the drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specifications.

Excavating trenches of required width in soil for Storm drainage pipes , including excavation for sockets and dressing of sides, ramming of bottom depth upto 0.9 Mtrs including getting out the excavated soil and then returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed within a lead of 50 mtrs. Dewatering if required during excavation to be included in the rate.

Providing & fixing including labour for following sizes of ASTM - D 1785 SCH 40 (Light Duty) U-PVC pipe with fittings like sockets, union, nuts, elbows, bends, reducers, plugs & T's etc. with solution jointing complete, including supply of clamps, nails etc. making holes in brickwalls and making good the damages by bringing them to original condition and complete in all respects as directed by the Architect. Fittings in schedule 40 conforming to ASTM D 2466. Internal Hydraulic pressure testing as per IS12235. Pasting radium Colour band near Valve, Colour text, flow direction arrow on pipe line at every 5 Mtr. Also including hydraulic testing for 2 hrs at 10 bar. The cost also include supports to the line.The rate shall include the cost of galvanized U clamps, bolts & nuts,supports with 2 coats of zinc chromate primer with 2 coats of enamel paint of total DFT minimum 100 micron. (For Domestic water municipal supply & & Tanker water supply to UGWT) 50 mm dia.( N.B. of pipe)

100 mm dia.( N.B. of pipe)

Providing and fixing Butterfly valve ISI marked, CI body including flanges / union, nuts, bolts, washer etc., complete as required. All valves shall be PN10 pressure rated. (For Domestic water municipal supply & & Tanker water supply to UGWT) 50 mm dia.

100 mm dia.

Providing and fixing water meter with non return valve including strainer, sockets / nion nut and including water meter box making locking arrangement and lock. [without chamber]. (For Domestic water municipal supply to UGWT) 50 mm dia.

Providing & fixing including labour for following sizes of ASTM - D 1785 SCH 80 (Medium Duty) U-PVC pipe with fittings like sockets, union, nuts, elbows, bends, reducers, plugs & T's etc. with solution jointing complete, including supply of clamps, nails etc. making holes in brickwalls and making good the damages by bringing them to original condition and complete in all respects as directed by the Architect. Internal Hydraulic pressure testing as per IS12235. Pasting radium Colour band near Valve, Colour text, flow direction arrow on pipe line at every 5 Mtr. Also including hydraulic testing for 2 hrs at 10 bar. The cost also include supports to the line. .The rate shall include the cost of galvanized U clamps, bolts & nuts,supports with 2 coats of zinc chromate primer with 2 coats of enamel paint of total DFT minimum 100 micron (Watersupply Pumping Line from UGT TO OHT Tank) 65 mm dia.( N.B. of pipe)

Providing and fixing Butterfly valve ISI marked, CI body including flanges / union, nuts, bolts, washer etc., complete as required. All valves shall be PN10 pressure rated. (For Domestic Pumping Line from UGT TO OHT Tank) 65 mm dia.

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Filling in plinth and floors with approved excavated material in 15cm. to 20cm. Layers including watering and compacting etc. complete.

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete.

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

GardenSoil: Supplying on site garden soil well sieved 90% to passthrough I.S.sieve of 10 mm size free from stones,rubbish liked ried grassroots and other such materials.The soil should be fresh from quarry.The colour of soil geerallybered.The soil will be measured by measuringbox (farma). (Item includes royaltycharges,transportin,loading unloading etc.) Lead charges for 35Km is considered.

FARM YARD MANURE: -Supplying on site well decayed, well dried, well powdered, without clods and free from stones, dried grass and other rubbish material. The color of the m anure generally is black. The manurewill be measured by measuring box. (Farma) Item includes Transporting, loading -unloading etc ( Lead charges per 35 km considered.)

Providing and fixing heavy duty inter locking concrete RUBBER MOULD GLOSSY PAVING BLOCKS of 60 millimeter thickness of having a strength of 400 Kilogram/sq.m of approved quality and shape on a bed of crushed sand of 25 to 30 millimeter thick including striking joints and cleaning etc. complete. (using 100% crushed sand)

Providing and Laying factory made coloured chamfered edge Cement concrete grass paver blocks of required strength,thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine fine aggregate (natural sand/crushed sand VSI grade finely washed etc.), compacting and proper embedding/laying of inter locking paver blocks into the fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and cutting of paver blocks as per required size and pattern, finishing and sweeping extra fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and complete as per manufacturer spsecifications & direction of Engineer-in-Charge. 60mm thick CC paver block of M-35 grade concrete with approved colour and design & pattern.

Providing and casting in situ or precast tapering R.C.C. M-20 Semi Barrier type Kerb without gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant

Preparing Flower Bed-Excavating the ground toa required depth of 30 cms.Removing rubbish&conveying unwanted stufftoarequired distanceas directed.Filling freshgarden soil& manurein excavated area in3:1proportiontoa heightof 30cms.Mixing garden soil and manure thoroughly well,leveling,watering onpreviousnight.Planting well,levelling,waterin gon previousnight.Planting well developed shrubs plants,0.50mtr.height,0.45Mtrs,apartas dircte dand 553580.65 maintaining till well established b ywatering,weedings,Stirringreplacing,replacing casualatie etc. complete

Preparing instant Lawn (20 cm depth) Excavating the groundtoa required depth of 20cms,removing&conveying unwanted stufftoa required distanceas directed. Filling fresh garden soil/silt&manure inexcavatedarea in3:1proportion to a height of2 0cms.Mixing garden soil andmanure thoroughly well,leveling and watering on previous night.Plantin g required variety of lawngrassas directed andmaintainingtill well establis hed by watering, weeding, clipping, rolling,etc.complete.

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete.

Machine polishing to cement/marble mosaic tiled flooring or any other type of flooring including cleaning, washing, etc. complete.

Providing and laying machine cut machine polished shahabad Stone slabs 20 to 25mm thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete.

Providing and fixing machine cut mirror polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition with full moulding the edges etc. complete. One side polish

Providing and applying two coats of textured synthetic paint of approved shade and quality and one coat of primer before applying textured paint including scaffolding if necessary preparing surface by thoroughly cleaning oil,grease,dirtandothermaterials as required, etc. complete.

Providing and fixing corrugated galvanised iron sheets of 0.63mm thick (24 B.W.G.) for roofing without wind tiles including fastening with galvanised iron screws and bolts, lead and bitumen washers as per drawing etc. complete.(Weight of 5.5 Kilogram/sq.m.).

Providing and fabricating structural steel work in rolled sections, fixed with connecting plates or angle cleats in main and cross beams, hip and jack rafters, purlins connecting to truss members and the like, as per detailed designs and drawing or as directed including cutting, fabricating, hoisting, erecting, fixing in position, making riveted/ bolted/ welded connections and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete.

Provinding and errecting 1.20m high Fix knot fencing Bezinal 2000 Type fencing having 11 Rows of 2.40 mm Bezinal 2000 wire on M.S. angle 50x50x5 mm embedded in c c block of 1:4:8 of size 450x450x910 mm at end and block of 450x450x760 mm at intermediate, 4.80m specing of pole with "S" clip high Tensile Bezinal 2000 including pulling high tensile wire with 5 Tone capacity puller including finishing and scoat of oil painting to M.S. angle etc. complete

Providing & laying Natural Sand in play area or requried in play area as per engineer incharge incliding engineer inchcharge transport, tax, lead etc all complet.

Providing Pots 36"x18"x18"

Providing & Fixing Bench in Cement Mortor /Concrete Wooden Finishing on all External Surffaces

Foliage Trees (2 Feet) Alstonia/Satvin

Anola

Arjuna

Deshi Badam

Drooping Ashok

Palms Areca Palm

Royal palm

Executive's Table @ 1800Lx900Dx750HT Providing & Fixing of Table @ 1800Lx900Dx750HT - TOP & GABLE END to be made of Membrane finish with soft water fall edges & curved panel & Decorated Anodized section MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band as per drawing.

Pedestal Unit @ 420Lx450Dx650HT Providing & Fixing of PEDESTAL @ 420Lx450Dx650HT :- To be made out of Complete Membrane consist of three Drawers as per drawing.

Credestal @ 1200Lx450Lx650HT Providing & Fixing of LOW HEIGHT CREDESTAL @ 1200L X 450D X 650H :- To be made out of Membrane Finish ( 2 Openable Shutter & 3 Drawer Pedestal in between )as per drawing.

Executive Table @ 2250Lx2100Dx750HT including Low Height Credestal @ 1200Lx450Dx650HT Providing & Fixing of Table @ 2250Lx2100Dx750HT TOP & GABLE END to be made of Membrane finish with soft water fall edges & curved panel & Decorated Anodized section MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band. INCLUDING CREDESTAL @ 1200L X 450D X 650H :- To be made out of Membrane Finish ( 2 Openable Shutter & 3 Drawer Pedestal in between ) as per drawing.

Free Standing Table @ 1500Lx600Dx750HT Providing and fixing Table of Size1500x600x750mm. Top:made from25mm - Prelaminated Particle board. All edges are covered by 2mm.Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Legs : C Shape made from CRCA Sheet with Powder Coat finish. Modes typanel :Made from18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edgeb and s glued by hotm elt glue applied by auto edge banding machine. KEYBOARDTRAY(WITHOUTMOUSETRAY) :-MetalPowderCoated-BlackColor,CPU TROLLEY:-Metal Powder Coated- Black Color, 3 DRAWERPEDESTALUNIT having over all size 392Lx450Dx680 Ht.mm.withcentral lockandkey.Drawers and body are complete metal with powder coat finish, facia in 18mm prelaminated particle

Free Standing Table @ 1200Lx600Dx750HT Providing and fixing Table of Size 1200 x 600 x 750 mm. Top: made from 25 mm Prelaminated Particle board. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Legs : C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel : Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :- Metal Powder Coated - Black Color, CPU TROLLEY :- Metal Powder Coated - Black Color, 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board,

Free Standing Table @ 1200Lx600Dx750HT Providing and fixingTable of Size1200x600x750mm. Top:made from 25mm Prelaminated Particle board. All edges are covered by2mm.Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine.Legs:CShape made from CRCA Sheet with Powder Coat finish.Mode sty panel:Made from18mm both side prelaminated particle boards.All edges are covered by0.8mm PVC edge bands glued by hotmetglue applied by auto edge banding machine. KEYBOARD TRAY (WITHOUT MOUSE TRAY) :-Metal Powder Coated-Black Color, CPU TROLLEY:-Metal Powder Coated-Black Color, 3 DRAWER PEDESTALUNIT having overall size392Lx450Dx680Ht.mm. with central lock and key.Drawers and body are complete metal with powder coat finish, facia in18mm prelaminated particle board.

Library Area Table @ 1350Lx750Dx750HT Providing & Fixing of FREE STANDING TABLE @ 1350Lx750Dx 750HT:- TOP to be made of 25 mm thick Prelaminated particle board with PVC edge band, BENT LEG to be CHROME FINISH as per drawing.

Providing & Fixing Curviliner Workstation @ 1500/1500Lx600/600Dx750HT Providing & Fixing Curviliner Workstation @ 1500/1500Lx600/600Dx750HT, Curvilinear Table Top @ 1500/1500Lx600/600D :- TOP to be made of 25 mm thick Prelaminated particle board with PVC edge band, GABLE END to be made of 25 mm thick Prelaminated particle board with PVC edge band, KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :- Metal Powder Coated - Black Color, CPU TROLLEY :- Metal Powder Coated - Black Color, along with 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. 3 Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board,

Conference Table @ 3600Lx1400Dx750HT Providing&FixingofMainTable@3600Lx1400Dx750HT-madeupof 18+18m ThickMDF top with PVC Membrane finish and waterfall edge profile. Aluminium Anodizied finish beeding of 4mm thichisrunning all over the table top edge.GableendsisAerofoiledShapewithfrontedges inPVCMembranefinishandrest inPrelaminated MDF with batton structure.Gableends should be hollow from inside for the provision of passing electrical and Datawiring. ,MODESTYPANEL:-to be made of 18mm thick Prelaminated particle board with PVC edge band Access Flap:- For Wire manager 2 Nos.

Conference Table @ 1800 x 900 x 750 mm Ht. Providing & Fixing of Main Table @ 1800Lx900Dx750HT - made up of 18+18mm Thick MDF top with PVC Membrane finish and waterfall edge profile. Aluminium Anodizied finish beeding of 4mm thich is running all over the table top edge. Gable ends is Aerofoiled Shape with front edges in PVC Membrane finish and rest in Prelaminated MDF with batton structure. Gable ends should be hollow from inside for the provision of passing electrical and Data wiring. , MODESTY PANEL:- to be made of 18 mm thick Prelaminated particle board with PVC edge band Access Flap:- For Wire manager 1 Nos.

12 Seater Reading Table for Library @ 3600Lx1200Dx750HT Providing and Fixing 12 Seater Reading Table for Liberary @ 3600Lx1200Dx750HT Top: made from 25 mm Prelaminated Particle board. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Gable Ends : made from 25 mm Prelaminated Particle board. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Modesty panel : Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.

3 DRAWER PEDESTAL UNIT @ 392L x 450D x 680Ht. mm. 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. 3 Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board.

Low Height Openable Storage @ 900Lx450x750HT Providing and fixing Openable Steel storage of 900x450x750Ht,with 2 adjustable shelves, Complete body & shutter made in 0.8mm thick &Topin 2mm thick CRCA,2 Shutter to be mounted with th ehelp of cuphinges,and 4a djustabl elevelers, enitre storagein powder coated finishw

Medium Height Steel Storage @ 750Lx450Dx1200HT Providing and fixing Openable Steel Storage of 7 50x450x1200Ht ,with 2a djustableshelves, Complete body & shutter madei n 0.8 mm thick & Topin 2mm thick CRCA,2Shutter to be mounted with th help of cuphinges,and 4adjustable levelers, enitre storage in powder coated finish with 60 to 80 microns. with 25 mm. thk. as per drawing.

Full Height Steel Storage @ 750Lx450Dx2100HT Providing and fixing Openable Steel Storage of 750x450x2100Ht ,with 4 adjustable shelves,Completebody&shuttermadein 0.8mmthick&Top in2mmthickCRCA,4 Shutter to be mounted with the help of cuphinges,and 4 adjustabl elevelers, enitre storage in powder coated finish with 60 to 80 microns as as per drawing.

Multiple Compartment Lockers @ 1140Lx 457D x 1830 mm. Ht. Providing and fixing Multiple Compartment Lockers @ 1140Lx 457D x 1830 mm. Ht. with 12 Compartments , Complete body & shutter made of CRCA Sheet with powder coated finish as per approved color.

Book Case with Glass Shutter @ 825Lx300Dx1650HT Providing & Fixing of Book Cas with Glas s Shutter@825Lx300Dx1650HT:-Tobe made out of complete body & in0.7mm thick CRCA& Shutter in1.2mmthickCRCA with glass pannel in Powder coating finish as per drawing.

Providing &Arrangemnt o High Back,Synchronized Mechanism with Multiple Locking,Adjustable Arm est,Gaslift for Seatheight adjustment,Standard5-pro erite Upholstery

Providing & Arrangemnt of High Back Chair - TILT MECHANISM WITH MULTILOCKING, HIGH DENSITY CUSHION ON SEAT COMPOSITE LEATHER WITH METALLIC SILVER FINISH BASE AND ARMS WITH P.U.CASTORS GASLIFT FOR HEIGHT ADJUSTMENT.

Providing&Arrangemnt ofMIdBack,NormalSyncroMechanism, FixedArmrest ,Gaslift for Seat height adjustment, Standard 5-prong/Nylon Base with Leather Upholstery

Providing & Arrangemnt of Mid Back, ECOCTS Mechanism,Fixed Armrest ,Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Fabric Upholstery

Public Seating Chair. - 3 Seater Providing and Fixing 3 seate r Public seating chair made of complete metal with Legs in Crome finish and seates in silver powder coating finish.

Stool for Lab and Class-IV Providing and fixing 4 legged Lab stool , Legs made of 16 Guage 45 MM Outer dimension M S Pipe , Duly painted ,With a 304 Grade Stainless steel 12 inch wide se at witha 1 inchcollar,Height adjustment viaa screw. as per design and drawing and instructions of Engineer in charge

Alluminium foldable ladder for store Providing & Fixing Foldable Alluminum Ladder 1500 mm. Ht.

Sofa Set 3+1+1 Providing & fixing SofaSet 3+1+1 Brown and Cream leather DIMENSION Length: 182.5(cms) Breadth(cms):100(cms)Height (cms):100(cms)Weight (Kilograms):66 (Kilogram) Seating Capacity: Five Seat

Tea Table 900mm X 750mm X 450mm for m.s. ante chamber Providing And Fixing Of Tea Table 900mmX750mmX450mm With 12 mm Thick Colour Eitched Tempered Glass With Bevelled Drawing Made Out Of 18mmThick Waterproofing Ply. The Outer Laces To Be Finished With High Quality 4 MmThik Veneer Or 1 Mm Thik Mica Etc.

Single Bed @ 2025LX 1000DX 650H Providing and fixing Single Bed of Size 2025Lx1000Dx650H with matress and pillow. Understructure: - The legs are made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2 mm. The legs should have corner brackets welded to it at two levels. The corner brackets are made of 2mm thick CRCA having a L shaped structure to join the side panels and headboard to the leg. Three nos. of Horizontal stiffeners are provided at equal intervals. The stiffeners are made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. The middle Horizontal Stiffener has a leg attached to it to transfer the load to the ground and add to the strength and stability of the complete structure. This leg is also made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. All Metal components to undergo 7 tank treatment process and should be powder coated to the thickness of minimum 50 Microns DFT.

Dressing Table @400LX 400DX 1800H Providing & Fixing Dressing Table of size 400L X400DX1800H .The Dressing table unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding . The unit has one drawer and one shelf .The dressing table has a mirror of 4mm thick pasted on 18 mm thick prelmparticle board attached to the base unit . The mirror size considered is 1155x360x4(t).The mirror has been pasted using high quality 3M sticker.

Wardrobe with Mirror @ 900LX 600DX 1965H Providing and Fixing Wardrobe with Mirror of size 900L X600 DX1965 H The wardrobe side panel sand doors are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The shelves are made of 18 mm thick Prelam Particle Board with decorative laminate on both sides.The top is made of 36mm prelam particle board with decorative laminate on both sides. (18mm Prelam Particle board and18mm bat on so n all sides to achieve 36mm overall thickness).The exposed edges of the to pare sealed with 2mm thick PVC edge Banding.The top most part of the wardrobe has an aluminum hanger rod of EBCO make. One drawer of size 400(W)x150(H)x450(D) made of 18mm thick prelam Particle Board has been considered .The drawer will have a multipurpose lock of EBCO premium make.The wardrobe handles are Satin S S finish of 160 mm pitch.The wardrobe has a multipurpose lock of EBCO make.All hinges considered are Hettich make.Necessary good quality hardwares have been considered as required.

Bed Side Table @ 400LX 400DX 415H Providing and Fixing Bed Side Table of size 400L X400D X415H The bed side unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate.All exposed edge s are sealed with 2 mm thick PVC edge Banding. The bed side table has one drawer and one shelf. The shelf is made of 18 mm thick Prelam Particle Board with bothside decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding

Kitchen Trolley Providing and Fixing stainless steel kitchen trolley of overall 26 " height and 22"depth, supported on aluminium pipes, trolley basket made out of 5mm stainless steel rod fitted on telescopic channel of size1.5"x20"x22"on both sides of trolley of 12"or above size, panel having 40 Kilogram load bearing capacity of trolley made out of 20mm PUC coated plywood and colour combination as directed by E-I-C. Inner side of panel covered by white mica,100 mm s .s. decorative handle. (The width and height of individual compartments shall be kept as directed by Engineer-in-charge)

Royalty Charges

Aggregate - Water abosorption ,Specific gravity ,Inpact value,Crushing value

Sand - Fineness modulus (Sieve analysis )Silt clay content

Bricks - Water absorption, compressive strength (set of 5bricks) Efflorences (set of 5 bricks)

Mix Design - Concret mix design (with all test on absic materials)

Concrete Cube - Compressive strength of CC cube (set of 3 cubes)

Cement - Fineness, consistancy, setting time, compressicve strength, specific gravity