COMPLETION OF INCOMPLETE WORK FOR PROVN OF OTM ACCN FOR LIGHT REGT AT SCHOOL OF ARTY DEOLALI

Amount

NOTE:- Schedule 'A' Part I to XIII are prepriced by MES, Bidders shall insert their lumpsum amount in the Blue Coloured field under Column -13 only.

Lump sum price worked out by the contractor for Sch 'A' Part-I (BUILDING WORKS )

Lump sum price worked out by the contractor for Sch 'A' Part-II (Internal Water Supply)

Lump sum price worked out by the contractor for Sch 'A' Part-III (Internal Electrification)

Lump sum price worked out by the contractor for Sch ‘A’ Part IV (External Water Supply )

Lump sum price worked out by the contractor for Sch ‘A’ Part V (External Electric Supply )

Lump sum price worked out by the contractor for Sch ‘A’ Part VI (Lightening protection )

Lump sum price worked out by the contractor for Sch ‘A’ Part VII (Solar Water Heater System )

Lump sum price worked out by the contractor for Sch ‘A’ Part VIII (Road /Paths & Culvert and Hardstanding )

Lump sum price worked out by the contractor for Sch ‘A’ Part IX (Sewage Disposal )

Lump sum price worked out by the contractor for Sch ‘A’ Part X (Area Drainage )

Lump sum price worked out by the contractor for Sch ‘A’ Part XI (Fencing ,Gate & Compound Wall )

Lump sum price worked out by the contractor for Sch ‘A’ Part XII (Football/Basketball/Volleyball/Parade Ground )

Lump sum price worked out by the contractor for Sch ‘A’ Part XIII (Earthwork and Excavation & Site clearance)

Sch 'A' Part-XIV (Miscellaneous B/R and E/M Works) Note :- This schedule is not pre-priced by MES and the rate indicated as "Rs. 0.00" under column F signifies this fact only.

Supply and fix for stop value 15 mm , cast copper alloy CP with crutch handle complete all as specified and directed.Make Jaguar cat part-OPL 15053 (CP) / cera cat part -CS 308A or Hindware cat part-F-220005

Supply and fixing for 15 mm CP wall mixer with telephonic shower arrangement with hand shower clutch & flexible CP pipe 1.15 m long for iron pipe including concealed stop cock complete all as specified and directed Make Jaquar cat part-OPL 15119 (CP) / cera cat part -CS 310A or Hindware cat part-F-220022.

Supply & Fix ceiling fan (after assembling the same) with the existing fan hook/box, 1200 mm (48") sweep and connecting up complete with and including three core copper conductor flexible cord of 0.5 Sqmm cross sectional area, of reqd length from ceiling rose to procelain connector block of the fan, including fan rod, not less than 15 mm dia. complete all as specified and directed.

Supply & Fix exhaust fan, single phase, heavy duty, metallic frame, 300 mm (12") sweep, 1400/1450 RPM including fixing of mounting frame complete with all accessories complete all as specified and directed.

Supply & Fix exhaust fan, single phase, heavy duty, 450 mm sweep, metallic frame, 1400/1450 RPM including fixing of mounting frame complete with all accessories complete all as specified and directed.

Supply & Fix wall mounted LED light fitting, 4 feet long with 18 W LED tube rod and batten double side connection type complete all as specified and directed.

S & F 11 W surface mounted round shape LED downlight capable of delivering 1200 lumen. having minimum luminous efficiency > 100 lumen/W, CCT 6500K, CRI > 80, high quality polycarbonate diffuser, input voltage range 140- 270 V, input frequency 50- 60 Hz, including electrical connection complete all as specified and directed by the Engineer-in-Charge.

S&F wall mounted LED light fitting, 2 feet long with 9W, polycarbonate housing and integrated electronic driver complete all as specified and directed.

S & F 25 W recessed mounted square shape 2' X 2' LED luminaire panel capable of delivering 3000 lumen, 6500K having high efficiency long life LED package in integral module with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, high transmittance polystyrene opal diffuser, housed in white powder coated pressure die-cast aluminium heat sink having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Copper conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed.

S& F Building security light fitting with pressure die cast aluminium housing, suitable for and including tube light 25W LED, complete pre-wired, including suitable bracket for fixing light on wall or any indicated location all as specified and directed .

S & F MCB single pole 240 volts 6 Amps to 32 Amps 10 KA 'B' series

S & F MCB single pole 240 volts 40 Amps to 63 Amps 10 KA 'B' series

S/F MCB SP & N 240 Volts 6 Amps to 32 Amps 10 KA 'B' series

S/F MCB SP & N 240 Volts 40 Amps to 80 Amps 10 KA 'B' series

S & F MCB TP 240Volts 63 Amps to 80Amps 10 KA 'B' series

S & F MCB TP 240Volts 40Amps 10 KA 'B' series

S & F MCB TPN 240Volts 63 Amps to 80Amps 10 KA 'B' series

S & F MCB TPN 240Volts 80Amps to 125Amps 10 KA 'B' series

S&F LED lamp 9W 230V complete all as specified.

Material & labour for cutting the existing CI pipe line of 100mm dia for insertion of Tee and including CI Tee of size 100x100x80mm in poistion including necessary CI collar, lead joints, etc complete all as specified and directed.

Supply and fixing and testing CI sluice valves 80 mm bore, both ends flanged and drilled, with stainless steel spindle , bannet wedge stuffing box, gland thrust plate, hand wheel made out of grey CI complete suitable for tested hydrostatic pressure PN 1.6 ISI marked including joints and jointing material complete all as specified and as directed.

Material & labour for construction of valve pit chamber having internal dimensions 900mmx900mmx900mm complete all as specified and directed by Engr-in-charge.

Material & labour for Cutting of existing bituminious road surfaces ie. Soling etc. and making trench of minimum 500 mm wide and 600 mm depth across road for laying of water mains,returning ,filling in, well ramming and removal of surplus spoil to distance of not exc. 50m complete all as specified and directed.

Supply & Fix FRP juction box of size outside dimensions 333 x 233 x 120 mm of make sintex, Cat No GSJB-2020 including 20mm connector, MCB SP 6 Amps - 01 No and fix on pole with and including MS clamps made out of 25 x 3mm MS flat iron, nut, bolts etc. complete.

S & F 45 W street light having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficacy of ≥ 2600 lumen/W, 5700K, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP 66 protection, high efficiency polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, suitable for side entry, pole mounting with bracket arm OD 35 mm to 42 mm including necessary electrical connection to the fixture with 3 core flexible Cu conductor cable of appropriate size and 1.5 m long bracket, having 40 mm diameter light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enamel paint over a coat of red oxide primer complete in all respect as specified and directed by engineer-in-charge. light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enamel paint over a coat of red oxide primer complete in all respect as specified and directed by Engineer-in-Charge.

M&L for earthing complete with 600x600x6.3mm galvanised steel earth plate electrode buried vertically in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the plate at a depth of not less than 1.5m below ground level, connected to and including G.I. Strip of size 32x6 mm by means of bolts,nuts and check nuts and washers of galvanised steel (and 40mm dia GI medium grade pipe for protection of G.I strip) to the extent of 7.5 metres as earthing lead and connecting to the eqpt, viz transformer, L.T. kiosk, H.T.lightening arrestors etc. including charcoal dust and salt packed all around the earth plate in the earth pit all as per electrical plate No. 3 of SSR Part I (2009) including PCC foundation / chamber in mix 1:2:4 type B1 with M.S. angle iron frame, C.I. Cover with provision of locking arrangement and 20mm dia light grade G.I. Pipe from top edge of the earth plate upto M.S. funnel with wire mesh provided inside the concrete earth pit for watering arrangement complete including excavation and earthwork in any type of strata and testing complete all as specified and directed. NOTE:- Earthing srrip beyond 7.5m shall be measured and paid seperately under relevent schedule.

Supply, install testing and commissioning weather and vermin proof L.T. feeder pillar box (Panel board)factory fabricated out door cubicle/kiosk type totally enclosed made out of 3.15 mm thick sheet metal enclosure of suitable size, with angle iron base frame of M.S. angle 50x50x6 mm suitable for operation on 3 phase 4 wire, 440 volts 50 HZ system as per IS 5039 of 1983 partially test type with hinged panel doors (cover ) on two sides with handles bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/rubber/wooden bushes to prevent ingress of water/vermin etc, inside the enclosure, the required nos of holes to be fixed with chromium plated brass cable glands for cable entry and exit complete with necessary internal wiring with stranded copper conductor PVC insulated cables of adequate size, duly powder coated externally and internally of grey or any other approved colour, including connecting with L.T. armoured incoming and outgoing cables and including required sizes of cable lugs of aluminium complete all as specified and directed and consisting following.

(b) MCCB 4 pole, 35 KA ,250Amp, - 1 No. (incoming)

(c) MCCB TP, 160 Amp, 30 KA - 2 No. (outgoing)

(d) MCCB TP 63 Amp, 25 KA 415 V - 2 No. (outgoing)

(e) MCCB SPN 32 Amp, - 3 No.

(g) Indicator lamps (RYB) one set

(h) Timer switch 240 V, 50 HZ single phase 70 Amps for automatic ON/OFF operation of street lights feeder complete with 1 No contactor ML 4 all duly wired for automatic operation of street lights cat No ET 100 of L&T or equivalent make as approved by GE. -( 01Sets)

Supply, install testing and commissioning weather and vermin proof L.T. feeder pillar box (Panel board)factory fabricated out door cubicle/kiosk type totally enclosed made out of 3.15 mm thick sheet metal enclosure of suitable size, with angle iron base frame of M.S. angle 50x50x6 mm suitable for operation on 3 phase 4 wire, 440 volts 50 HZ system as per IS 5039 of 1983 partially test type with hinged panel doors (cover ) on two sides with handles bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/rubber/wooden bushes to prevent ingress of water/vermin etc, inside the enclosure, the required nos of holes to be fixed with chromium plated brass cable glands for cable entry and exit complete with necessary internal wiring with stranded copper conductor PVC insulated cables of adequate size, duly powder coated externally and internally of grey or any other approved colour, including connecting with L.T. armoured incoming and outgoing cables and including required sizes of cable lugs of aluminium complete all as specified and directed and consisting following.

(b) MCCB TPN, 25 KA ,100Amp, - 1 No. (incoming)

(c) MCB TPN, 63 Amp, 25 KA - 3 Nos. (outgoing)

(e) MCB SPN 32 Amp, - 4 Nos.

(g) Indicator lamps (RYB) one set

(h) Timer switch 240 V, 50 HZ single phase 70 Amps for automatic ON/OFF operation of street lights feeder complete with 1 No contactor ML 4 all duly wired for automatic operation of street lights cat No ET 100 of L&T or other makes specified -( 01Sets)

Supply, install testing and commissioning weather and vermin proof L.T. feeder pillar box (Panel board)factory fabricated out door cubicle/kiosk type totally enclosed made out of 3.15 mm thick sheet metal enclosure of suitable size, with angle iron base frame of M.S. angle 50x50x6 mm suitable for operation on 3 phase 4 wire, 440 volts 50 HZ system as per IS 5039 of 1983 partially test type with hinged panel doors (cover ) on two sides with handles bottom gland plate and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/rubber/wooden bushes to prevent ingress of water/vermin etc, inside the enclosure, the required nos of holes to be fixed with chromium plated brass cable glands for cable entry and exit complete with necessary internal wiring with stranded copper conductor PVC insulated cables of adequate size, duly powder coated externally and internally of grey or any other approved colour, including connecting with L.T. armoured incoming and outgoing cables and including required sizes of cable lugs of aluminium complete all as specified and directed and consisting following:-

(b) MCCB 4 pole, 35 KA ,100Amp, - 1 No. (incoming)

(c) MCB TPN, 63 Amp, 25 KA - 3 Nos. (outgoing)

(e) MCB TPN 32 Amp, - 2 Nos.

(g) Indicator lamps (RYB) one set

(h) Timer switch 240 V, 50 HZ single phase 70 Amps for automatic ON/OFF operation of street lights feeder complete with 1 No contactor ML 4 all duly wired for automatic operation of street lights cat No ET 100 of L&T or other makes specified -( 01Sets)

Supply and install HT 11 KV drop out fuse consisting of channel iron base ,having 2 Nos 11 KV post insulators per phase complete with fuse carrier of SRBP tube with heavily tinned non ferrous metal parts and spring loaded phosphor bronze contact with 200 A fuse element for 11KV complete all as specified and directed.

M&L for PCC block of 200mmx200mm size in cement concrete 1:2:4 type B-1 using 20mm grade stone aggregate for fixing the insulators and aluminium strip on roof for lightning conductor including porcelain inusulator of minimum height 50mm and 50mm width with galvinised mild steel nuts & bolts,washers and suitable for fixing aluminium strip of size 25mmx3mm,all as specified and directed.

Supply, Installing, testing & Commissioning of Solar hot water system suitable for inlet water including control valves chlorine & fluorine content upto 100PPM & comprising of solar flat plate collectors, collector stand assembly, stainless steel insulated hot water storage tank including supporting structure as per manufacturers instructions with heat exchanger, sacrificial anode, electrical back up etc complete of capacity 100LPD with 'B' size collectors with electrical heating back upto 1.8 KW complete all as specified and directed.

M&L for Lagging to pipes used in internal water supply or plumbing all round with 25 mm thich bonded mineral wool preformed 'SNAPON' pipe sections of density 144 Kg/cum confioming to IS-9842 for following sizes of pipe :-

(a) Internal dia 15 mm bore

(b) internal dia 20mm bore

Supply ,Install, test and commission of split type air conditioner 2 TR capacity, 5 Star rating, with cordless remote control ,including provision of air pipes and copper tubes, suitable for AC, with and including foam insulation, fixed to walls / ceilings / floors with connected accessories complete all as specified and as directed.

S&F 2mm thick aluminium sheet of bonded with blue retro reflective sheeting of engineering grade having pressure sensetive adhesive,including fixing to angle frame work all as directed.

M&L Writing letter or figure(block,Roman,Italic,English or Hindi,Arrows,Dashes etc n. exc 15cm high of white retro reflective sheet of thickness 0.3mm fixed on blue retro reflective sheeting of engineering grade having pressure sensetive adhesive, all as specified.

M&L Writing letter or figure(block,Roman,Italic,English or Hindi,Arrows,Dashes etc) above 15cm and n.exc 30cm high of white retro reflective sheet of thickness 0.3mm fixed on blue retro reflective sheeting of engineering grade having pressure sensetive adhesive, all as specified.

Supply and install water coolers electric driven (single phase), having storage capacity of 80 liters and nominal cooling capacity of 40 Liters/hour complete all as specified and directed.

Supply and install water coolers electric driven (single phase), having storage capacity of 120 liters and nominal cooling capacity of 60 Liters/hour complete all as specified and directed.

Supply and install deep freezer hard top 120 litres capacity having single door, single phase 230 volts complete all as specified and directed.

Supply & Laying in trenches/ducts, connecting, testing and commissioning of cable HT XLPE, insulated armoured under ground system, screened protected, PVC bedded galvanized steel strip or wire, armoured electric power cable(heavy duty) with Aluminium conductor 11 KV(E) suitable for earthed system ISI mark of size 95 Sqmm 3 core complete all as specified and as directed.

Supply,laying, jointing,testing and commissioning LT cable 1100 volts grade, XLPE insulated armoured and PVC sheathed with stranded aluminium conductor heavy duty, conforming to IS 1554 Part I / ISI marked, to be laid in trenches, fixed along the poles or through G.I. Pipe laid under floors road etc; fixed concealed in walls encased in G.I. Pipe etc. complete of following sizes:-

(a) 150 Sqmm 3.5 Core

(b) 70 Sqmm 3.5 Core

(c) 50 Sqmm 3.5 Core

(d) 25 Sqmm 4 Core

(e) 16 Sqmm 4 Core

(f) 10 Sqmm 4 Core

(g) 16 Sqmm 2 Core

(h) 10 Sqmm 2 Core

Supply and install deep freezer hard top 200 litres capacity having single door, single phase 230 volts complete all as specified and directed.

Material & labour for construction of septic tanks for 25 users as shown in TD Drg. No. CEPZ/92/TD/17M complete all as specified and directed by Engr-in-charge.

Material & labour for construction of septic tanks for 50 users as shown in TD Drg. No. CEPZ/92/TD/17M complete all as specified and directed by Engr-in-charge.

Material & labour for construction of septic tanks for 150 users as shown in TD Drg No. CEPZ/93/TD/12-STR complete all as specified and directed by Engr-in-charge.

Material & labour for construction of Filter bed for 150 users as shown in TD Drg No. CEPZ/88/TD/19M complete all as specified and directed by Engr-in-charge.

Material & labour for construction of Soakage well for 50 users shown in TD Drg. No. CEPZ/2004/TD/8 complete all as specified and directed by Engr-in-charge.

S&F Basket ball ring with net & fibre board 12mm thick made of one piece, non refelctive type, flat front surface fixed in frame with screws complete all as specified and directed.

S&F Football Goal net with post including all necesaary fittings with screws complete all as specified and directed.

Provn.of steel gate 6.00m wide and 2.70m in height complete all as shown in TD Drawing No. CEPZ/91/TD/15M complete all as specified and directed by Engineer in charge.

Horizon Construction

Ramjidas Construction Pvt Ltd

M/s M R MAHANA

nhsaluji and associates

M.R.Mutha Engineers

United Sales Corporation

ganesh electricals and airconditioners

SOOD ASSOCIATES PVT LTD