Construction of Smart Fencing Boundary Wall brick without plaster at Phanus Basumatary Memorial M.E. School

Amount

Civil Works: (A) Brick Wall: Earth work in excavation by mechanical means (Hydraulic excavator)/Manual means over areas (excluding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in-charge. 2.8.1 All kinds of soil

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with jamuna sand, with common burnt clay non modular bricks.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 4.1.5: l:3:6 (l Cement : 3 coarse sand (zone-lll) derived fiom natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 5.22.3 Cold twisted bars.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 5.22A 1. Mild steel and Medium Tensile steel bars.

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement -All work up to plinth level 5.1.3:-1:2:4 (1 cement: 2 coarse sand (zone-III): 4 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor level, excluding cost of centering, shuttering, finishing and reinfocement: 5.2.2 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Half brick masonary with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13.1 Cement mortar 1:3 (1 cement: 3 coarse sand)

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. 16.70.1 Made of G.I. wire of dia 4 mm

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/stell works

Painting with silicon & acrylin emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces. 13.51.2: Two Coats sqm 132.65

(B) Iron Gate, 2 Nos.: Earth work in excavation by mechanical means (Hydraulic excavator)/Manual means over areas (excluding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in-charge. 2.8.1 All kinds of soil

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with jamuna sand, with common burnt clay non modular bricks.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level. 4.1.8-1:4:8 (1 cement: 4 coarse sand (zone-III): derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 5.22.3 Cold twisted bars.

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for: 5.9.6 Columns, Pillars, Piers, abutments, posts and struts.

Centering and shuttering including strutting, propping etc. and removal of form for: 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing and laying on position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement All work up to plinth level: 5.1.2-1:1.5:3 aggregate 20 mm nominal size

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor level, excluding cost of centering, shuttering, finishing and reinfocement: 5.2.2 1:1.5:3 aggregate 20 mm nominal size.

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.1 Cement mortar 1:4 (1 cement: 4 coarse sand)

15mm cement plaster on the rough side of single or half brick wall of mix: 13.2.1-1:4 (1 cement: 4 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: 13.43.1 Water thinnable cement primer.

13.44 Finishing walls with water proofing cement paint of required shade: 13.44.1 New work (two or more coats applied @ 3.84kg/10 sqm)

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface etc. complete. 13.52.1 On steel work

(C) Const. of Urinal & Latrine: Earth work in excavation by mechanical means (Hydraulic excavator)/Manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) etc. 2.8.1 All kinds of soil

Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks. 11.1.2 1.6 (1 cement: 6 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level. 4.1.5 in prop. 1:3:6 aggregate 20 mm nominal size.

Steel reinforcement for RCC work including straightening cutting bending placing in position and binding all complete upto plinth level. 5.22.4 Hot rolled deformed bars.

Steel reinforcement for RCC work including straightening cutting bending placing in position and binding all complete upto plinth level. 5.22.1 Mild steel and medium tensile steel bars.

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for: 5.9.6 Columns, Pillars, Piers, abutments, posts and struts.

Centering and shuttering including strutting, propping etc. and removal of form for: 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing and laying on position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement All work up to plinth level: 5.1.2-1:1.5:3 aggregate 20 mm nominal size

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor level, excluding cost of centering, shuttering, finishing and reinfocement: 5.2.2 1:1.5:3 Aggregate 20 mm nominal size.

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.1 Cement mortar 1:4

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Half brick masonary with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor five level. 6.13.1 Cement mortar 1:4

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commerical mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb etc. 10.14.3 Profile E 10.14.3.2 Fixing with carbon steel galvanised dash fastener of required dia size (to be paid for separately).

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.1- Hot finished welded type tubes.

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia meter with bitumen and G.I. limpet washers etc. 12.1.3.0. 63 mm thick with zinc coating not less than 275gm/m2

Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] etc. complete. 12.66.4 Precoated/mill finish aluminium Barge board (Upto 200 mm)

15mm cement plaster on the rough side of single or half brick wall of mix: 13.2.1 1:4 (1 cement: 4 fine sand)

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 ce3ment: 3 coarse sand), finished with a floating coat of neat cement. 11.6.1 18mm thick

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level. 4.1.5 in prop 1:3:6 aggregate 20 mm nominal size.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make etc. 11.41.1 Size of tiles 500x500 mm.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades etc.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of requored size with necessary screws, excluding panelling which will be paid separately, all complete. 9.5.1 Second class teak wood 9.5.1.1 35mm thick shutters

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with nuts and screws etc. complete. 9.96.1 300 x 16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with nuts and screws etc. complete. 9.97.2 250 x 10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. 9.100.1 125 mm

Providing and fixing, ISI marked, aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with nuts and screws etc. complete. 9.95.1 125x75x4 mm

Making plinth protection 50mm thick of cement concrete 1:3:6 (zone-III) stone aggregate 20mm, nominal size) over 75mm thick bed of dry brick ballast 40mm nominal size etc.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufactures specifications: 13.48.2 Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of applied @0.75 ltr/10 sqm of approved brand and manufacture.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufactures specifications: 13.48.3 Painting steel work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of applied @0.80 ltr/10 sqm of approved brand and manufacture.

Wall painting (two coats) with plastic emulsion paint Approved brand and manufacture (Asian paint/Berger etc. to give an even shade etc. (a) Plastic paint/Berger Paint/ICI paint/J&N paint/Nerolac)

Applying one coat of water thinnable cement primer of approved brand and manufacture on new wall surface: 13.43.1 Water thinnable cement primer.

13.44 Finishing walls with water proofing cement paint of required shade: 13.44.1 New work (two or more coats applied @ 3.84kg/10 sqm)

Providing of Tube Well platfrom with brick work, CC work plastering etc.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Sanitary Installation and water supply works: Providing and fixing water closet squatting pan (Indian type W.C. Pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white PVC flushing cistern, including flush pipe, etc. 17.1.1 White Vitreous china orissa pattern W.C. pan of size 580x440 mm with integral type foot rests .

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern etc. 17.4.1 One urinal basin with 5 litre white P.V.C. automatic flushing cistern.

Providing and fixing soil, waste and vent pipes. 17.35.1 100 mm dia 17.35.1.1 Sand cast iron S&S pipe as per IS: 1729

Providing and fixing soil, waste and vent pipes. 17.35.2 75 mm dia 17.35.2.1 Sand cast iron S&S pipe as per IS: 1729

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 17.38.1 100 mm dia 17.38.1.1 Sand cast iron S&S as per IS-1729

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 17.38.2 75 mm dia 17.38.2.1 Sand cast iron S&S pipe as per IS-1729

Providing and fixing single unequal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 17.47.1 100x100x75 mm 17.47.1.1 Sand cast iron S&S as per IS - 1729

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete. 19.27.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

Providing and placing in position filters of 40 mm diameter G.I. Pipe with brass strainer of approved quality

Providing and placing in position hand pump of approved quality for 40 mm diameter G.I. pipe complete with all accessories.

Septic Tank: Earth work in excavation by mechanical means (Hydraulic excavator)/Manual means in foundation trenches or drain (not exceeding 1.5m in width or 10 sqm on plan) etc. 2.8.1 All kinds of soil

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including etc.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 4.1.5: l:3:6 aggregate 20 mm nominal size.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 5.22.1 Mild steel and Medium Tensile steel bars.

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.1 Cement mortar 1:4

Providing and laying on position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement All work up to plinth level: 5.1.2-1:1.5:3 aggregate 20 mm nominal size

12 mm cement plaster finished with a floating coat of neat cement of mix: 13.7.1 1:3 (1 cement: 3 fine sand)

Providing precast cement concrete jail, 1:2:4 reinforced with 1.6 mm dia mild steel wire, including centering and shuttering etc. 5.18.1 50 mm thick.

Sanitary Fittings: Providing and fixing single equal plain junction of required degree. 17.44.1 100x 100x 100 mm 17.44.1.1 Sand cast iron S&S as per IS-1729

Providing and fixing in position pre-cast RCC manhole cover and frame of required shape and approved quality. 19.19.2 MD-10 19.19.2.1 Square shape-450mm internal dimension

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc.complete.

Bithwn Boro

ANSUMA BORO