Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L-1₹18.4 LAccepted-AOC 361 BEHIND DAV SCHOOL JAWAHAR NAGAR SRINAGAR 190008 | SRINAGAR | JAMMU AND KASHMIR | 190008 | L-1 | Accepted-AOC Tender accepted due to lowest and quoted reasonable rates | |
| 2 | L-2₹18.9 L+₹51,423.30 (2.80%)Rejected-Finance HOUSE NO 102 LANE NO 4 C ANAND NAGAR BOHRI JAMMU 180002 J K | JAMMU | JAMMU AND KASHMIR | 180002 | L-2 | Rejected-Finance Higher side quoted amount | |
| 3 | L-3₹18.9 L+₹54,262.90 (2.95%)Rejected-Finance HOUSE NO 251 E BLOCK ADARSH NAGAR BALLABHGARH FARIDABAD 121004 HARYANA | FARIDABAD | FARIDABAD | HARYANA | 121004 | L-3 | Rejected-Finance Higher side quoted amount |
Tender Value
Refer Docs
EMD Value
₹36,240
Closing Date
5 Dec 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
CWE Khumbathang
CWE Khumbathang
SPECIAL REPAIR TO 02X62.5 KVA DG SETS AGAINST BER AT ASCON NODE AND ARTY BDE UNDER GE KHUMBATHANG
2022_MES_561848_1
80051/112/E8
Open Tender
Miscellaneous Works
Item Rate
180 days
khumbathang
As per tender and NIT doc
8 documents required · 8 mandatory
₹500
GE Khumbathang
₹36,240
Yes
27 Dec 2022
7 Nov 2022
6 Dec 2022
7 Nov 2022
5 Dec 2022
21 Nov 2022
Amount
Supply and installation, testing and commissioning of diesel engine driven generating set of capacity 62.5 KVA (50 KW), 4 cylinder in line 4 stroke,415 Volts, 0.8 power factor at NTP, mounted on common base frame with flexible coupling, 1500 RPM, with silencer pipe protected with asbestos rope independently supported from engine to outside of power house up to 0.50 metre, AVM pads, PCC 1:2:4 type B-I (using 20mm graded crushed stone aggregate) foundation as per manufacturer's design, cold starting kit, battery start with suitable cables for connecting from DG set to panel board and with first fill of lube oil and coolant (DG set shall be capable of operating in temp range of (-35°C to + 35°C) complete with and including the following:-
(A) PRIME MOVER. Vertical engine of suitable capacity water cooled (Radiator mounted) EG complete 50:50, bore 95x115mm, CR 19:1, Displacement 3.3 ltr, ISO 8528-5 G2, CI4+ 15W40, exhaust pipe size 3 inch, mean piton speed 5.75 m/sec, air intake @ 100 % load 160 CFM, exhaust temp 490 degree celcius, closed circuit as per BS-649 or IS-10002 direct injection type turbo charged electric starting system having rated speed 1500 RPM. DG Set conforming IS/IEC 60034-1, IS 1460, ISO 8528/3046/9001 AND IS 13018. Engine protection low lube oil pressure, high/low coolant temp, battery over/under/weak volts, fail to crank/start, sensor failure, cranking lockout, low fuel level and alternator protection over/under voltage, over/under frequency,, loss of ac sensing etc.The DG set shall be capable of running 24 hours continously with 10% overloading for one hour in every 12 hours run as per BS-5514/BS-649. Engine shall be equipped with all standard fitting as per manufacturer's recommendations and mounted on common base frame with following fittings:
(a) RPM cum hour meter (b) Battery charging ammeter (c) Ignition key and starting with push button switch (d) Lubricating oil pressure guage. (e) Mechanical/electronic governor controlling. (f) Oil tempature gauge. (g) Water tempature gauge. (h) Lub oil coolant heater to avoid freezing. (j) Coolant Heater (k) Oil drain pump (l) 24 Volts cold starting kit comprising with the following:- (i) 2 Nos, 12 volts 180 AH batteries. Make: Exide/Standard Furukawa/Amaron. housing in wooden box with glass wool insulation all around as directed. (ii) Battery Charging alternator with inbuilt regulator (iii) Starter motor of suitable capacity. (iv) Battery leads(copper cable) of suitable size with brass thimbles and terminals. (m) Cold starting kit with engine block heater and sump heaters. (n) Any other fitting/accessories as recommended by the manufacturer.
(B) ALTERNATOR. Alternator rating 62.5 KVA (50 KW), 3 phase, 50 cycles 415 Volt, 4 wire supply at NTP 0.8 power factor running @ 1500 RPM self excited, self regulated , mounted on a strong fabricated steel frame suitable for mounting on a permanent foundation to be coupled with above engine. Voltage regulation plus minus 1 %, insulation class H, winding pitch 2/3, stator winding double layer lap, dynamically balanced rotor, waveform distotion no load < 1.5 %, total harmonic distortion non distorting balanced linear load <5 % , max unbalanced load across phases <= 25%.Dedicated winding specially designed for 1 phase operation.The alternator shall be conforming to IS/IEC 60034-1, BS-2613 of IS-4722. Make: Kirloskar/Crompton/Jyoti/NGEF/StamfordCGT. (C) Alternator control panel CRCA sheet, floor mounted, cubical type with internal copper wiring with copper coductor cable of suitable size for 62.5 KVA alternator, 415 volts, 3 phase 4 wire, 50 cycles fabricated out of 1.6 mm thick MS sheet, painted internally and externally with two coats of epoxy powder coating paint over a coat of red oxide primer, including following accessories:-
(b) Fuel tank with provision of cleaning of suitable capacity as per manufacturer's instructions capable to store 12 hours running of dg set with supprting fabricated steel stand with all pipes connecting upto fuel pump including oil level indicating gauge, drain & air vent plug etc. (c) silencer to meet MoEF/ CPCB noise emmission standards. (d) Rubber matting. Chequred of size 2m x 1m x 12mm thick (e) Tool kit for maintenance of DG set NOTES FOR ITEM NO-1 (i) The DG Set shall be provided with an intergral acoustic enclosure to meet MoEF/CPCB norms of 75dBA @ 1 mtr at 75 % load under free field conditions, CRCA sheet in munsel green shade, structural base frame in black paint, insulation material PU foam complying IS 8183, fuel filling arrangement inside the enclosure, 11 tank pretreatment process and UV resistent powder coating of all parts to withstand extreme environment, air inlet louvers and shall comply the revised noise limit for DG set vide GSR 371 (E) dated 17 May 2002 and its amendments under Environment (Protection) act 1996 issued by the Min of Envronment and Forests. (ii) The contractor shall produce a copy of approved certificate to authanticate the above from the OEM/OEA Notes:- (i) Load test will be carried out after installation in the presence of testing officer. (ii) The DG set shall be tested by the contractor in presence of the accepting officer's representative/ IEM & Engineer-in-charge without any extra cost and the quoted rates are deemed to be included for all these aspects. (iv) Payment of DG Set's will be made after satisfactory testing.
M&L for earthing complete for DG SET with GI earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 Mtr below ground level) with top edge of earth plate not less than 1.5 Mtr below from ground level connected to GI strip 32x6mm by means of nuts, bolts, thimbles, chuck nuts, washers of copper, PCC (concrete chamber) 1:2:4 type B-1 using 20mm graded stone aggregate copy shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate, internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4 funnel wiht wire gauge of 22 gauge (0.68mm) 8 mesh per liner inch, 50 mm thick cover of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with 8 mm four MS bars @ 80mm centre to centre both ways and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified including provision of earth wire protected by 15mm dia medium grade pipe and watering pipe shall be 40 mm bore medium grade, all excavation and earth work & connectiing the earthing to an earthing test point as specified and testing on complete all as specified & directed by Engr-in-Charge.
Excavating in over area and n exc 1.5 m in depth; for foundation , and getting out in any type of rocky/hard soil complete all as specified and as directed.
Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in hard/dense soil complete all as specified and directed by Engr-in-Charge.
Removal of excavated soil to distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed by Engr-in-Charge.
Sand cushioning with fine sand to under ground cables in trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable as specified in clause 19.75 of SSR Part-I complete all as specified and directed by Engr-in-Charge. (Note:-Punned thickness shall be measured and paid)
Supplying and laying unreinforced precast concrete cable cover, class LV, type 1 flat of size 250mm x150mm x 40mm placed perpendicular of the cable complete all as specified and directed by Engr-in-Charge.
Supply, laying & testing in repair cable XLPE insulated screened PVC bedded, galvanized steel strip armoured, electric power cables (heavy duty) with stranded aluminium conductor, 1100 volts grade, earthed system of size 3.5 core 70 sq mm complete all as specified and directed by Engr-in-Charge.
SUMEET TRADING CORPORATION
national engineering
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .