PROVN OF HARDSTANDING ALONGWITH CHAIN LINK FENCINGWITH IRON GATEAROUND FOL DUMP AT 41 MED REGT AT NURLA AND PROVN OF ONE STORE SHELTER FOR STORAGE OF SCME CLOTHING AT HQ 118 (I) INF BDE GP OMC AT NIMU, UNDER AGE(I)NIMU

Amount

Sch "A' Part-I B/R work:- Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out hard/dense soil

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil, complete.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/disintegrated rock, complete.

Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and removing surplus soil to a distance not exceeding 50 m

Returning , filling in excavated soil including spreading , leveling watering and well ramming in layers not exceeding 25 cm thick complete

Removing excavated material (soils) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point, complete.

M&L for PCC 1:2:4 type B-2 (using 40mm graded crushed stone aggregate) as in foundations of post, filling and mass concrete

M&L for cement concrete type D-2, 1:4:8 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete.

M&L for pre-cast cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate ) block masonry with solid blocks, exc. 10 cm in width and setting in mortar 1:6, and set as in wall etc

M&L for 75mm thick cement concrete type D-2, 1:4:8 (using 40mm graded crushed stone aggregate) as in sub base.

S&F mild steel hold fasts, wall ties and similar small articles conforming to Fe 290-0 or E 165

M&L for cement concrete , 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in lintel upto 1.50 m span, cills, steps, seismic and other silmilar bands, plinth courses, sring courses,lacing courses, parapets and railings upt 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troghs and the like including weathering, slightly rounded or camphered angles and throating, as directed.

M&L for RCC 1:2:4 type B-1 ( using 20 mm graded crushed stone aggregate ) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete (Note:-TMT bars will be masured and paid sepretly)

M&L for RCC 1:2:4 type B-1 ( using 20 mm graded crushed stone aggregate ) as in Beams, cantilevers, bressummers, lintels over 1.5m span (Note:-TMT bars will be masured and paid sepretly)

M&L for RCC 1:2:4 type B-1 ( using 20 mm graded crushed stone aggregate ) as in Columns, pillars, piers, posts and struts (Note:-TMT bars will be masured and paid sepretly)

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter,

Use and waste of formwork to sides of concrete pillers, columns and similar work; vertical

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips.

All as per item No 08 here-in-before but but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe 410 W (Gde-E-250) quality A.

M&L for mild steel work in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165

M&L for mild steel bolts. purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Complete all as specified.

M&L for mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips and confirming with Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde - E-165)

Supply and fixing chain link fencing 3.15mm dia of mild steel galvanised steel wire and mesh size 100 x 100 mm complete all as specified. Note:-The actual weight of Sqm unit should be measured by BOO convened by AGE(I)

S&F galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs , including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

M&L for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete and confirming with Fe 410-W (Gde-E- 250) quality-A

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for preparation of new surfaces of steel of any description , over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge ..

M&L for preparation of new surfaces of steel of any description , n.exc 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge ..

Rendering 15 mm thick on fair face of brick work or concrete/stone surfaces in CM 1:6 finished even and smooth without using extra cement.complete all as specified and directed by Engr-in-Charge.

Rendering 15mm thick on fair face of brick work or concrete/stone surfaces in CM 1:4 mixing with WPC @2% by weight of cement or as per manufacturer instruction and finished even and smooth without using extra cement.complete all as specified and directed by Engr-in-Charge. Note:WPC will be measured and paid sepratly.

Supply only water proofing compound.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed by Engr-in-Charge ..

M&L for 2nd class Hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

M&L for 2nd class hardwood 40mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats for doors.

S&F 100mm long butt hinges, medium weight, cold rolled mild steel

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy.

S&F 200mm long aluminium anodised, barrel tower bolts of extruded section

S&F 4mm thk sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5 sq.m in each pane

M&L for preparation of new wooden surfaces of any description, not otherwise descri-bed, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for 2nd class soft wood Plain fillets.sec area exc. 13 & n.exc 25 Sq cm as in square, rectangular or triangular in section, clean sawn, secured with nails or brads.

All as per srl item No. 44 here-in-before but sectional area n.exc 3 sq cm bull nosed, splayed, chamfered or rounded on one edge or face

S&F 6mm thick Plywood, 5 no of ply, grade BWR, type BB, fixed with nails to timber frame work as in ceiling complete

M&L for hardcore of gauge n exc. 63 mm of broken stone or boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L for 150mm thick PCC 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) as in foundation, filling & mass concrete

M&L for 100mm thick PCC 1:1.5:3 type A-1 (using 20mm graded crushed stone aggregate) as in topping layer finished surface even and fair without using extra cement complete all as specified

Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm prmied and sealed with sealing compound, Grade `A' for 100 mm thick slab complete all as specified & directed. (Note:-The rate should be included for joint making machine)

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40 mm graded crushed stone aggregate in plinth protection including provision of necessary form work finishing the exposed surface even and smooth complete all as specified.

M&L for 25mm thick cement concrete type B-0, 1:2:4 (using 12.5mm graded crushed stone aggregate) as in sub base.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including laid over screed bed of 15mm thick of cement mortar 1:6 all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the shade of tiles including laid over backing coat of 10mm thick of cement mortar 1:4 all as specified and directed.

Sch 'A' Part-II E/M work:- M&L for point wiring with two single core PVC insulated, unsheathed, FRLS type, 1100 volts grade, multistranded copper conductor cable 1.5 sqmm in and including PVC casing caping ISI marked with all connected accessories including one single core multistanded PVC insulated FRLS type, 1.5 sqmm copper conductor cable unsheathed as earth continuity cable including closed recessed wooden terminal boxes of suitable size made of 2nd class hard wood for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet top cover complete all as specified for the following:- Make of cable: Finolex/Polycab/Havells/Plaza. (a) One light /fan/bell point/buzzer point exhaust fan controlled by one nos, one way 5/6 Amps switch.

One 3 pin socket outlet, 5 Amps, independent, with cables 1.5 sq. mm size

One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5 sq. mm size

All as per srl item No 55 here-in-before but with conductor of size 4 sqmm (Nominal area) for one 3 pin socket outlet 15 Amps on independent board complete and earth continuity wire with 4 sqmm PVC insulated stranded copper conductor Cable.

S&F Socket outlet multipurpose 2 in 1, 3 pin, 5 and 15 amp flush type

S&F Socket outlet multipurpose 3 pin, 5A, and 2 pin 5A flush type

S&F Switch piano, flush type single pole, one way 5 Amp

S&F Switch piano, flush type single pole, one way 15 Amp

S&F Ceiling rose 65x50mm, 2 to 3 terminal PVC/polycarbonate, isolated body

S&F LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size

S&F sheet metal powder coated versatile double door SPN distribution board, 8 way suitable for MCB's fitted with copper bus bar rated 200amps, neutral link , earth bar and din rail suitable for use on 240 Volt, 50Hz .

S&F MCB SPN 63 Amp 240 volt AC with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed.

S&F MCB SP 6-32 Amp 240 volt AC with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed.

Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing lead of 4mm dia galvanised iron or steel wire all as shown in Plate No. 2 to the earthing test point all as specified and indicated including testing on completion

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth; for laying of cable/pipe & getting out in any type of soil complete all as specified and directed

Removal of excavated soil to distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed

Returning filling in including spreading, levelling, watering and well remming in layers not exceeding 25cm thick in hard/dense soil complete all as specified.

Supply, laying and testing LT XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 16 sq. mm 2 core complete all as specified

S&F DWC tubing of size 90/76mm dia for laid in trenches/along the pole/wall for protection of cable complete all as specified and as directed.

osho traders

CHHIRPON BUILDERS

MS INFRATECH