Construction of One Room,Kitchen and Bathroom on EP land at Rawalpora Srinagar.

Amount

Dismantling of old existing structure made of brick masonry covered with CGI sheet roofing including disposal of dismantled material as required. The cost of dismantled material shall be deducted from the overall cost of the work

Earth work in excavation by manual means of trenches for foundation, drains, pipes cable etc (not exceeding1.5m in width) and for shafts wells, cesspits and the like not exceeding 10sqm on plan including dressing of sides and ramming of bottoms lift upto 1.5m including getting out excavated earth and disposal of surplus excavated earth as directed in all kinds of soils

P/L soling stone(90-150mm size) hand packed all complete.

P/L in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level in 1:4:8(1cement:4coarse sand:8 graded stone aggregation 40mm normal size)

P/L in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:3:6(1cement:3coarse sand:6 graded stone aggregation 20mm normal size) with 20% boulders.

Centring & shuttering including strutting, propping etc and removal of form for

Foundations, footings, bases of columns etc for mass concrete.

Lintel, beams, plinth beams, girders etc

Suspended floor, roofs, landings balconies etc

Edges of slab under (20cm wide)

Reinforced cement concrete work in plinth beams in 1:1/2:3 mix( 1cement;1 1/2 coarse sand:3 graded stone crushed aggregate 20mm nominal size including curing but excluding cost of shuttering finishing and reinforcement.

Providing wood work in frames of doors, windows, clerestory windows and other frames wrought framed and fixed in position with hold fast lugs or with fasteners of required dia and length(hold fast lugs shall be paid for separately) first class KD wood.

Providing 40x5mm flats iron hold fast 40cm long including fixing to frames with 10mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm in 1:3:6 mix

Brick work with common burn clay(non-modular) bricks of class designation 7.5 in super structure above plinth level upto floor five level in cement mortar 1:6(1cement:6coarse sand)

Steel reinforcement for RCC work including straightening, cutting binding placing in position and binding all complete upto required level(T.M.T bars)

Reinforced cement concrete work in beams suspended floors, roofs having slope upto 15, landings, balconies, chajjas, shelves, Lintels, bands, staircases etc upto floor five level including curing but excluding cost of shuttering finishing and reinforcement in.

1:1½:3(1cement:1½ coarse sand:3 graded stone crushed aggregate 20mm nominal size)

Smooth finishing of the exposed surface of RCC w ork with 6mm thick cement mortar 1:3(1 cement:3 fine sand) including curing

15mm cement plaster of mix 1:6 (1 cement:6 coarse sand) on rough side of brick wall.

12mm cement plaster on fair side of brick wall in 1:6 mix(1cement:6 coarse sand)

Cement concrete flooring 1:2:4(1 cement: 2coarse sand:4graded stone crushed aggregate 20mm nominal size) finished without a floating coat of neat cement and curing complete(40mm thick)

P/L vitrified floor titles in 600x600mm size with water absorption less than 0.08% and confirming to 1S:15622 of approved made in all colours and shades laid on 20mm thick cement mortar 1:4(1cement:4coarse sand) including grouting the joints with white cement and matching pigments etc complete.

P/F 30mm thick glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws(1st class KD wood).

P/F 30mm thick wire gauze shutters using M.S. wire gauze of average width for aperture 1.4mm in both directions with wire of dia 0.63mm for doors, windows and clerestory windows with ISI marked MS pressed butt hinges finished of required size with necessary screws as per directions of Engineer in charge(1st class K.D wood)

P/F 35mm thick panelled doors shutters with panel of pre-laminated particle board(12mm thick) decorative lamination on both sides, 12mm thick coir veneer board including fixing with butt hinges bright finished of required size with necessary screws(1st class K.D.wood)

P/F hardware accessories

Sliding door bolts(250x16mm) Aluminium

Tower bolts(100x10mm) Aluminium

Handle(100mm) Aluminium

Handle (125mm) Aluminium

P/F 1st quality ceramic glazed wall titles conforming to 1S:15622(thickness not less than 5mm) of approved make in all colours shades of any size as approved by Engineer incharge in skirting risers of steps and dia over 12mm thick bed of cement mortar 1:3(1cement:3coarse sand) and joining with grey cement sluring @ 3.3 kg/sqm, including pointing in white cement mixed with pigment of matching shade complete

P/F ceramic glazed floor titles 300x300mm or more (thickness not less than 5mm) of approved make of first quality of Nitco, orient, somany. kajaria etc in all colours and shades, laid on 20mm thick cement mortar 1:4 mix(1cement:4 coarse sand) including pointing the joints with white cement and matching pigments etc complete

Providing and applying white cement based putty of specified thickness of approved brand and manufacturer over the plastered wall surface to prepare the surface the surface smooth and even complete (1mm thick)

Applying primer coat with ready mixed pink or grey primer of approved brand and manufacturer on wood work

Supplying and filling in plinth with GSB under floors including watering, ramming consolidation complete.

P/L PVC conduct pipe heavy for wiring in roof/walls and cutting the chase wherever required(25mm)

Fan box(heavy)

Deep janction box(3")

Bend(25mm dia)

Junction box(wall)

MS box (18modules)

MS box (3modules)

MS box (8modules)

P/F 3 layer PP-R(poly propylene Random co polymer pipes) conforming to IS: 15801, UV stabilized and anti microbial fusion welded having thermal stability for hot and cold water supply including all PP-R plain and brass threaded poly propylene random fittings, this includes testing of joints complete as per directions of Engineer incharge (internal work) concealed fixing the pipes with clamps at 1.00 mtr spacing including cutting chases and making good the wall.

PN-16 pipe 25mm OD(SDR)-704)

PN-16 pipe 32mm OD(SDR)-704)

PPR unions 25mm

PPR unions 32mm

P/F unplasticized PVC water pipes conforming to 1S:13592 type A including jointing with seal ring conforming to 1S:5382 leaving 10mm gap for thermal expansion.

75mm dia

110 mm dia

P/F unplasticized PVC fittings/accessories for unplasticized rigid PVC pipes conforming to 1S:13592 type A including jointing with seal ring conforming to 1S:5382 leaving 10mm gap for thermal expansion.

Coupler

Single Tee with door

P-Trap (110mm)

Door bend

M/S SHEIKH CONSTRUCTIONS

Ghulam Qadir Bhat