Augmentation of water supply to National Institute of Technology Puducherry in Thiruvettakudy, Karaikal

Amount

Earth work in excavation by mechanical means (Hydraulic excavation) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10sqm on plan) including getting out and disposal of excavated earth, lead upto 50m and lift upto 1.5m - all kinds of soil

Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m - all kinds of soil

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m - all kinds of soil - pipes,cables etc , exceeding 80mm dia but not exceeding 300 mm dia

Close timbering over areas including strutting,shoring and packing cavities (whwerever required) etc. Complete (measurements to be taken of the face area timbered) . Depth not exceeding 1.5m

Close timbering over areas including strutting,shoring and packing cavities (whwerever required) etc. complete (measurements to be taken of the face area timbered) . Depth exceeding 1.5m but not exceeding 3m

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5

Extra for every additional lift of 1.5m or part there of in excavation / banking excavated or stacked materials - all kinds of soil

Supplying and filling in plinth with river sand under floors, including watering, ramming consolidating and dressing complete

Supplying and filling with gravel (excluding rock) in trenches , plinth, sides of foundations etc . In layers not exceeding 20 cm in depth consolidating each deposited layers by ramming and watering etc. complete including all lead and lift

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacture's specification.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering , shuttering , finsishing and reinforcement - All work upto plinth level 1:1.5:3 (1cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finsishing and reinforcement - All work upto plinth level 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size

Centering and shuttering including strutting, propping etc and removal of form for - foundations, footings, bases of columns etc for mass concrete

Centering and shuttering including strutting, propping etc and removal of form for - Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc and removal of form for - Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc and removal of form for - Lintels , beams, plinth beams, girders, bressumers and catilevers

Centering and shuttering including strutting , propping etc and removal of form for - Columns , Pillars , Piers , Abutments , Posts and Struts

Centering and shuttering including strutting , propping etc and removal of form for -Weather shade, Chajjas, corbels etc., including edges

Providing , hoisting and fixing upto floor five level precast reinforced cement concrete in lintels, beams, and bressumers including setting in cement mortar 1:3 (1 cement : 3 coarse sand) , cost of required centering and shuttering but excluding the cost of reinforcement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing , hoisting and fixing upto floor five level precast reinforced cement concrete in shelves including setting in cement mortar 1:3 (1 cement : 3 coarse sand) , cost of required centering , shuttering and finishing with neat cement punning on exposed surfaces but excluding the cost of reinforcement , with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size)

Steel reinforcement for R.C.C.work including straightening , cutting, bending, placing in position and binding all complete upto plinth level - Thermo -Mechanically treated bars (TISCON / VIZAG / IISCO / SAIL / JSW) Fe - 415 or more

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work , using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS : 9103 to accelerate, retard setting of concrete , improve workability without impairing strength and durability . Note:- Cement content considered in this item is @ 330 kg / cum. Excess or less cement used as per design mix is payable or recoverable separately. - All work upto plinth level

Extra for providing richer mixes at all floor levels - Note:- Excess / less cement over the specified cement content used is payable / recoverable separately - Providing M-30 grade concrete instead of M-25 grade BMC / RMC . (Note:- cement content considered in M-30 is @ 340 kg / cum)

Add for using extra cement in the items of design mix over and above the specified cement content therein

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S (non modular ) bricks of class designation 3.5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:6 ( 1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level upto floor V level - cement mortar 1:3 (1 cement : 3 coarse sand)

Providing wood work in frames of doors , indows, clerestory windows and other rames , wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -Vengai wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows, and clerestory windows, including ISI marked M.S.pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately , all complete - Vengai wood - 35 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors , windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick - Vengai wood

Providing and fixing M.S.grills of required pattern in frames of windows etc with M.S. flats , square or round bars etc. including priming coat with approved steel primer all complete - Fixed to openings / wooden frames with rawl plugs screws etc

Providing 40 X 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30 x10 x 15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing aluminium tower bolts , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade, with necessary screws etc. complete - 100 x10 mm

Providing and fixing of 65 mm Godrej Navatal lock of 7 levers with 3 keys etc complete

Supplying and fixing rolling shutters of approved make, made of required size M.S.laths, interlocked together through their entire length and jointed together at the end by end locks , mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to ISS :4454 -part 1 and M.S.top cover of required thickness for rolling shutters - 80 x 1.20mm M.S.laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters

Providing and fixing M.S. fan clamp type I or II of 16mm dia M.S. bar, bent to shape with hooked ends in R.C.C.slabs or beams during laying , including painting the exposed portion of loop, all as per standard design complete

Steel work welded in built up sections / framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets,gates and similar works

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc .complete - 40mm thick with 20mm nominal size stone aggregate

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make (Jhonson / Asian / Somany / Nitco) in all colours , shades of size 300 x 450 mm as approved in skirting , risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 300x450 mm

Providing and laying ceramic glazed floor tiles of size 300 x 300 mm (thickness to be specified by the manufacturer) , of 1st quality conforming to IS :15622, of approved make (Nitco / Kajaria ) in all colours, shades, except white , ivory, grey, fume red brown, laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand), including pointing the joints with white cement and matching pigments etc., complete

Providing and laying pressed clay tiles (as per approved pattern 18mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound , laid over a bed of 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete

12mm cement plaster of mix -1:4 ( 1 cement : 4 fine sand)

12mm cement plaster of mix -1:6 ( 1 cement : 6 fine sand)

15mm cement plaster on the rough side of single or half brick wall of mix - 1:6 (1cement : 6 fine sand)

12 mm cement plaster of mix 1:5 (1 cement : 5 fine sand)

cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement - 20mm cement plaster

15 mm cement plaster on the rough side of single or half brick wall of mix 1:5 (1 cement : 5 fine sand)

6mm cement plaster of mix 1:3 (1 cement : 3 fine sand)

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers

12mm thick plain cement mortar bands in cement mortar 1:4 (1cement : 4 fine sand) - flush band

12mm thick plain cement mortar bands in cement mortar 1:4 (1cement : 4 fine sand) - raised band

Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface - water thinnable cement primer

Finishing walls with acrylic smooth exterior paint of required shade - New work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm

Applying priming coat - with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Applying priming coat - with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron / steel works

Wall painting with plastic emulsion paint - Royal of approved brand and manufacture to give an even shade - two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - Two or more coats on new work

Dismantling manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - bituminous road

Providing and fixing 20mm thick , PVC shutter for doors , windows , cupboard etc., made of rigid PVC extruted multi chamber section of size 20mm x 200mm and outer edges of shutter framed with PVC channel section of size 24 mm x 59 mm , having interlocking facilities. The door frame of extruded PVC section of size 40mm x 48mm , having a maximum wall thickness 2.80mm 0.30mm . The corners and joints shall be mitrecut and welded. The rate shall include the cost of necessary hinges, handles and locking facilities wherever necessary

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P.brass waste of standard pattern , including painting of fittings and brackets ,cutting and making good the walls wherever required - white vitreous china flat back wash basin size 550x400 mm with single 15mm C.P. brass pillar tap

Providing and fixing white vitreous china water closet squatting pan (Indian type) - Orissa pattern W.C.pan of size 580x440mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete - flexible pipe - 32mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P.brass screws and washers complete

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour - 600 mm long towel rail with total length of 645 mm, 78 mm wide and effective height of 88mm, weighing not less than 190 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings , with one step CPVC solvement cement and the cost of cutting chases and making good the same including testing of joints complete - Concealed work , including cutting chases and making good the wall etc - 20 mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete - external work - 32mm nominal outer dia pipes

Providing and fixing gun metal gate valve with C.I.wheel of approved quality (Screwed end) - 32mm nominal bore

Providing and fixing unplasticised PVC connection pipe with brass unions - 45 cm length - 15mm nominal bore

Providing flanged joints to double flanged C.I / D.I. pipes and specials, including testing of joints - 150mm diameter pipe

Providing flanged joints to double flanged C.I / D.I. pipes and specials, including testing of joints - 200mm diameter pipe

Providing and fixing C.P.brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms - 15 mm nominal bore

Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931- 15 mm nominal bore

Providing and fixing PTMT grating of approved quality and colour - circular type - 100mm nominal dia

Constructing soak pit 1.20 x 1.20 x1.20 m filled with brick bats including 110 mm dia UPVC pipe (type B) 1.20 m long complete as per standard design

Providing and fixing on wall / column face unplasticed - PVC soil and waste pipes (type - B) conforming to IS : 13592- 1992 including jointing with seal ring conformation to IS : 5382 leaving 10mm gap for thermal expansion - single socked pipes -110mm diametre

Providing and fixing on wall face / column face unplasticised - PVC mould fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend with door 110 mm

Providing and fixing on wall / column face unplasticised - PVC soil and waste pipes (type B) conforming to IS :13592 - 1992 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single socketed pipes 75mm diameter

Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Bend 75 mm

Boring , providing and installing bored cast -in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring , with bentonite solution and temporary casing of appropriate lenghth for setting out and removal of same and the lenghth of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (length of pile for payment shall be measured upto bottom of pile cap) - 300 mm dia piles

Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end) - 20mm nominal bore.

Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end) - 25mm nominal bore.

Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end) - 40mm nominal bore.

Providing flanged joints to double flanged C.I./D.I. pipes and specials including necessary bolts, nuts, rubber insertion and testing of joints etc.,complete - 150mm diameter pipe.

Providing flanged joints to double flanged C.I./D.I. pipes and specials including necessary bolts, nuts, rubber insertion and testing of joints etc.,complete - 200mm diameter pipe.

Providing flanged joints to double flanged C.I./D.I. pipes and specials including necessary bolts, nuts, rubber insertion and testing of joints etc.,complete - 250mm diameter pipe.

Providing flanged joints to double flanged C.I./D.I. pipes and specials including necessary bolts, nuts, rubber insertion and testing of joints etc.,complete - 300mm diameter pipe.

Providing and fixing C.I. sluice valve (PN 1) (with cap) conforming to IS 14846 and ISI marked, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 100 mm dia.

Providing and fixing C.I. sluice valve (PN 1) (with cap) conforming to IS 14846 and ISI marked, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 200 mm dia.

Providing and fixing C.I. sluice valve (PN 1) (with handwheel) conforming to IS 14846 and ISI marked, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 200 mm dia.

Providing and fixing C.I. sluice valve (PN 1) (with handwheel) conforming to IS 14846 and ISI marked, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 250 mm dia.

Providing and fixing C.I. sluice valve (PN 1.6) (with handwheel) conforming to IS 14846 and ISI marked, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 100 mm dia.

Providing and fixing C.I. Double air valve with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 100 mm dia.

Providing and fixing C.I. non return valve (PN 1.6) conforming to IS 5312 and ISI marked, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 100 mm dia

Providing and fixing C.I. Ball type non return valve (PN 1) conforming to IS 318 & IS 1363, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 250 mm dia.

Providing and laying Ductile Iron socket and spigot pipes of class K7 (Electro steel/ Sripipes/ Jindal/ Electrotherm / Jai Balaji / TATA Metaliks Kubota) conforming to IS specification 8329/2000 and ISI marked suitable for tyton /push on joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS 12288 and CPWD specification. (earth work and jointing of pipes with rubber gasket will be paid separately) -150mm dia.

Providing and laying Ductile Iron socket and spigot pipes of class K7 (Electro steel/ Sripipes/ Jindal/ Electrotherm / Jai Balaji / TATA Metaliks Kubota) conforming to IS specification 8329/2000 and ISI marked suitable for tyton /push on joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS 12288 and CPWD specification. (earth work and jointing of pipes with rubber gasket will be paid separately) -200mm dia.

Providing and laying Ductile Iron Double flanged pipes of class K9 (Electro steel/Sripipes/Jindal /Electrotherm) conforming to IS specification 8329/2000 and ISI marked suitable for flanged joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches(or fixing in over head tanks above ground level) laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS12288 and CPWD specification . (earth work and jointing of pipes with rubber insertion will be paid separately) -150mm dia.

Providing and laying Ductile Iron Double flanged pipes of class K9 (Electro steel/Sripipes/Jindal/ Electrotherm) conforming to IS specification 8329/2000 and ISI marked suitable for flanged joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches(or fixing in over head tanks above ground level) laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS12288 and CPWD specification . (earth work and jointing of pipes with rubber insertion will be paid separately) -200mm dia.

Providing and laying Ductile Iron Double flanged pipes of class K9 (Electro steel/Sripipes/Jindal/ Electrotherm) conforming to IS specification 8329/2000 and ISI marked suitable for flanged joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches(or fixing in over head tanks above ground level) laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS12288 and CPWD specification . (earth work and jointing of pipes with rubber insertion will be paid separately) -250mm dia.

Providing and laying Ductile Iron Double flanged pipes of class K9 (Electro steel/Sripipes/Jindal/ Electrotherm) conforming to IS specification 8329/2000 and ISI marked suitable for flanged joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches(or fixing in over head tanks above ground level) laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS12288 and CPWD specification . (earth work and jointing of pipes with rubber insertion will be paid separately) -300mm dia.

Providing and fixing in position S&S standard D.I. specials (Electro steel/Sripipes/Jindal/ Kiswok) such as tees, bends, collors, tapers, caps etc.conforming to IS specification 9523 / 2000 and ISI marked - 100 to 300mm dia.

Providing and fixing in position flanged standard D.I. specials (Electro steel/Sripipes/Jindal /Kiswok) such as tees, bends, collors, tapers, caps etc.conforming to IS specification 9523 / 2000 and ISI marked - 100 to 300mm dia.

Providing and fixing D.I. dismantling Joint ISI marked, with bolts, nuts, rubber insertion etc.,complete -200mm dia.

Providing and fixing D.I. dismantling Joint ISI marked, with bolts, nuts, rubber insertion etc.,complete -250mm dia.

Providing and fixing D.I. dismantling Joint ISI marked, with bolts, nuts, rubber insertion etc.,complete -300mm dia.

Providing and fixing Cast iron flanges conforming to IS specification 1538 and ISI marked. - 100 mm dia.

Providing and jointing cast iron / D.I. (S&S) pipe joints with rubber gasket (Tyton joints) conforming to IS 5382 & 12820 of SBR quality including the cost of fixing,testing the joints etc.,complete -150mm dia.

Providing and jointing cast iron / D.I. (S&S) pipe joints with rubber gasket (Tyton joints) conforming to IS 5382 & 12820 of SBR quality including the cost of fixing,testing the joints etc.,complete -200mm dia.

Providing, laying and jointing G.I pipes of medium class (blue)(TATA, TNT,Nezone, Apollo, Zenith) conforming to IS specification 1239 part I and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including GI specials such as bends, tees, elbow, coupling,reducer etc.,complete all as per IS and CPWD specification. -20mm dia

Providing, laying and jointing G.I pipes of medium class (blue)(TATA,TNT, Nezone, Apollo,Zenith) conforming to IS specification 1239 part I and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment, including GI specials such as bends,tees, elbow,coupling,reducer etc.,complete all as per IS and CPWD specification. -25mm dia

Providing, laying and jointing G.I pipes of medium class (blue)(TATA,TNT, Nezone, Apollo, Zenith) conforming to IS specification 1239 part I and ISI marked including transportation to the site, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including GI specials such as bends, tees, elbow, coupling, reducer etc., complete all as per IS and CPWD specification. -40mm dia

Providing and fixing in position G.I. union (UNIQUE/R Brand/HB Brand/UI Brand) conforming to IS 1239 part II and ISI marked,including labour charges for jointing, jointing materials etc, complete- 20 mm dia.

Providing and fixing in position G.I. union (UNIQUE/R Brand/HB Brand/UI Brand) conforming to IS 1239 part II and ISI marked, including labour charges for jointing, jointing materials etc, complete- 25 mm dia.

Providing and fixing in position G.I. union (UNIQUE/R Brand/HB Brand/UI Brand) conforming to IS 1239 part II and ISI marked,including labour charges for jointing, jointing materials etc, complete- 40 mm dia.

Providing and fixing in position G.I. bend (UNIQUE/R Brand/HB Brand/UI Brand) conforming to IS 1239 part II and ISI marked,including labour charges for jointing,jointing materials etc,complete - 100 mm dia.

Supplying of electrically operated wet type submersible motor and pumpset (Texmo /KSB/ Taro/ Kirloskar make), AC 3 phase, 415 volts, 50 Hz, 2900-3000 RPM. The pump shall have brass impeller, high grade steel shaft with sufficient stages having outlet size of 2"/2.5"/3" dia. to suit the borewell (150 / 200mm dia.), complete. The rate includes, all taxes, freight, etc., FOR at site in UT of Puducherry. The pumpset shall be guaranteed for a period of one year from the date of commissioning.(15 HP Submersible motor and pumpset).

Supplying and fixing C.T. metering panel board as per Electricity Department Specification (Drawing enclosed). Panel board of size 1800mm x 900mm x 300mm made of 18 gauge CRMS sheet painted with two coats of enamel paint over Zinc chromate primer with necessary MS base channel. The panel board shall include power mat, copper busbar, 8mm thick Hylan sheet of size 84 x 54cm.

Supply and fixing of 300mm dia strainer

Providing and fixing of pressure gauge 0-5 KG/CM2 with necessary valve arrangements

Supplying and fixing of 25KVAR power capacitor (CG/L&T/Siemens make) for 50 HP motor complete.

Supplying and fixing of fully automatic air break star-delta starter range for 10A to 23A F.A.S.D. (Bharat Culter Hammer/L&T/Siemens make) with suitable M.S. angle frame etc., complete.- 15HP to 17.5 HP pumpsets

Supplying and fixing Fully Automatic Auto Transformer Starter (Pedestal Type)(Jyothi/ Kilburn/ Unilec) with oil immersed contactors and auto transformer having 50%,65% and 80% tapping with built in start stop push botton and thermal timer adjustable between 3-12 seconds (Relay range in Amps 48-80) - 40 HP pumpsets

Supplying and fixing of DOL starters 0.5 HP to 5 HP with relay range 0.63 A to 13 A with suitable M.S. angle frame complete.

Supplying and fixing of 1x3x6 sqmm (single run) PVC insulated copper submersible flat flexible cable of Finolex make complete.-12.5HP to 20HP pumpset

Supplying of 3.5x95 sqmm underground cable (Paragon/suncab/Empire) complete.- suitable for (60HP to 75HP pumpset)/(above 40KVA to 75KVA Genset).

Supplying of 3.5x150 sqmm underground cable (Paragon/suncab/Empire) complete.(above 82.5KVA to 125KVA Genset

Supplying of 3.5x185 sqmm underground cable (Paragon/suncab/Empire) complete.

Supplying of 3.5x240 sqmm underground cable (Paragon/suncab/Empire) complete.-(above 160KVA to 200KVA Genset).

Laying of UG cable and providing termination of cable joint with suitable cable gland,cable socket etc., complete - 3.5/4 x 50 / 3.5/4 x 70 sqmm cable.

Laying of UG cable and providing termination of cable joint with suitable cable gland,cable socket etc., complete - 3.5 x 95 sqmm cable.

Laying of UG cable and providing termination of cable joint with suitable cable gland,cable socket etc. complete - 3.5 x 185 sqmm cable.

Laying of UG cable and providing termination of cable joint with suitable cable gland,cable socket etc. complete - 3.5 x 240 sqmm cable.

Making earth pit of G.I. pipe for earthing in earth pit with 40mm dia. G.I. pipe medium class of length 3.05m perforated with 46 Nos of 12mm dia. holes, pipe lowered in bore holes of 150mm dia. and filled in with charcoal and salt in alternative layer of 300mm, the top of G.I. pipe shall be clamped. Earth pit shall be provided with 60cm dia precast ring with 60cm depth alround,covered with R.C.C. precast slab etc. as per I.E. standards.

Supplying and fixing of copper wire 8 SWG (4 mm dia) for earthing arrangements including bolt and nuts etc., complete.

Providing and fixing 50 mm dia GI pipe (Class B) conforming to IS 1239 (Part 1:1990) with GI fittings including trenching, refilling etc., complete for UG cable duct.

Supplying and fixing of copper flat (25 x 3mm) for earthing arrangements including bolts and nuts etc.

Supplying and fixing of C.I. adopter which is to be connected to submersible pump delivery pipe.-100 mm dia

Supplying and laying of 40mm dia. PVC pipe (Class 3 - PN 0.6 Mpa) conforming to IS 4985 : 2000 for inserting submersible cable from borewell to starter.

Supply and fixing of 80/100mm dia. M.S. erection clamps of size 80mmx12mm with bolts, nuts, washer etc., complete.

Supplying,fixing and lowering into the borewell the GI pipes of medium class (TATA,TNT, Nezone, Apollo, Zenith) which are to be connected to the submersible pump,including labour charges, jointing materials etc.,complete.-100 mm dia

Providing and fixing MS square threaded coupling (male and female thread) including necessary welding with 100mm GI pipe. -100mm dia.

Laying of under ground cable direct in ground including metal road cutting, excavation of earth, sand cushion, brick protection, back filling etc., complete. - above 50 sqmm

Supplying of electricallly operated horizontal split casing pump and motor(JYOTHI/ KIRLOSKAR/ BEACON) make AC 3 phase,415 volts,50 HZ,1500 RPM,squirrel cage motor.The pump shall have bronze impeller,high grade steel shaft,flexible coupling set,including the cost of common,M.S. Base plate,foundation bolts,etc.complete with suitable suctionand delivery sizes.(30 HP centrifugal motor and pumpset).

Supplying and fixing of 40 X 40 mm size vaccum pump (KIRLOSKAR /MAXWELL /DEKKAR) make 3 phase monoblock motor and pumpset complete.-3.7 KW/5 HP

Erection,testing and commissioning of the centrifugal motor pumpset with pipe fittings,etc.complete.- 30 HP to 50 HP motor.

Erection, testing and commissioning of motor and pumpset complete.The rate includes obtaining electricity service connection from Electricity Department also.

Supplying of 3 phase, 415 volts, 50 cycles, 0.8 power factor for electric starting diesel generator comprising the following units:- (Kirloskar/ Leyland / Ruston/ Greaves Cotton / Cummins make) water cooled and shall be of multi stroke, multi cylinders, cold starting, developing not less than127BHP under normal temperature and pressure. The engine shall conform to I.S. 10002 with latest amendments. It shall be capable of taking 10% over load for one hour in every 12 hours of continous operation including 6 Nos. of anti vibration pads.The engine shall be complete with the following accessories: Electrical starting provision, engine cooling fan, fuel and lubricating oil filters, oil bath, air filter, lub oil pressure gauge 250 litres capacity fuel tank mounted with engine, hour meter with exhaust manifold, flexible pipe, 12 /24 volts electric starting equipment complete with starter, alternator and two numbers of 12 volts with 21plates battery of make AMCO/ STANDARD / EXIDE/ DAGANITE (with Guarantee cards) of adequate capacity and low lubricating oil pressure / high temperature varying engine shut down devices. The Acoustic enclosure shall have the following:

Acoustic enclosure shall be powder coated and fabricated out of 16 SWG CRCA MS sheet. The silent canopy shall be of nut bolt type construction. Powder coating is done after seven tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of FIRE-RETARDANT foam/Rock Wool as acoustic material. Four hinged doors shall be provided to canopy, one door shall have glass window for control panel.Base frame is fabricated either in ISMC channel or in sheet metal. The base frame is rugged in construction and designed for mounting engine and alternator, with cross members mounted on AVM. The base frame shall have provision for mounting of acoustic enclosure and it is having provision of lifting hook for convenient lifting of complete set, i.e. along with canopy, engine and alternator.Fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connections of suitable capacity. The Acoustic enclosure shall be Type test approved as per CPCB norms. The average sound level, when measure in green field condition (ISO m3744 OR 8528 PT 10) at 1-meter distance from all four sides shall be less than 75-dBA average or as per CPCB norms.

The average stabilized hot air temperature rise with in the canopy is maintained with in 10 C over and above ambient temperature.Acoustic enclosure is suitable for Outdoor / Indoor installation. Lockable doors shall be provided. Lockable fuel filling arrangement to be provided external to the canopy. Residential Silencer is housed in the canopy. The exhaust gasses shall be taken out through a suitable flexible pipe to prevent any back pressure on the engine. Base frame sturdy, fabricated welded construction, channel iron / sheet metal base frame for mounting the above engine and alternator.Standard Tools and Spares:Double ended spanners complete set (small and big size sets) -12 Nos. (TAPARIA/ GEDORGE / EVEREST make) Screw driver (30cm long) Taparia make. Screw driver (45cm long) Taparia make. Cutting plyer.Diesel filter with elements - 2 Nos.Oil filter with elements - 1 No.All the above accessories with complete set. Alternator The alternator shall be of Crompton /Kirloskar/ Stamford/ELGI make, self excited, self regulated, screen protected, drip proof alternator with static excitation system capable of developing 100 KVA at 0.8 power factor 415 volts, 3 phase, 50 cycles, generally conforming to I.S.4722 under normal condition, the voltage

Providing and fixing of suitable M.S.exhaust pipe including 2 Nos. of M.S. bends (long), 7 Nos. of M.S. flanges, M.S. pipe Class B - 5 Rm as flexible exhaust pipe. The rate is inclusive of transportation charges for shifting of welding machine and gas cutting set to site, consumption of welding rod 10 SWG and cutting gas, providing fasterners of 10mm bolts / nuts / washers and flange gaskets including labour charges etc. as per IE standard.-80 mm dia exhaust pipe (From 50 KVA to 100 KVA)

Providing and laying of aluminium cladding with 50 mm thick glass wool slab with chicken mesh and covered with 24 SWG aluminium sheet (the rate includes double calculation for flanges & bends) as per I.E. standards.

Providing and fixing of fire safetyequipments comprising 1 No. of 4.5 kg of CO2 fire extinquisher 1m x 2m x6mm thick rubber mat shock proof of superior quality with two numbers of 10 litres capacity fire buckets (red colour) with M.S. stand arrangements etc.

Providing and fixing of 4 pole change over switch of STANDARD/HAVELLS/KUNDAN/ GEM make including M.S. frame as per I.E. standard.-400 Amps(Above 100 KVA)

Charges for transporting, erection, testing and commissioning of generator set excluding foundation,but including mechanical and other unskilled wages for installation of equipment, wiring from generator set to panel board and change over switches, handling charges, purchase of spares if any required for the installation and commissioning, the cost of fuel and other materials for a trial run of 6 hours. This rate also includes for testing and commissioning of generator set as specified, obtaining approval of Central Electricity Authority (CEA), payment for CEA inspection/Licence fees or any other charges and fulfilling other requirements and conditions laid down by CEA-From 62.5 / 63 KVA to 100 KVA

Supplying and fixing C.I. cover without frame for manholes - 560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg

Drilling of borewell any where in Karaikal including tranportation in alluvial soil, sedimentary strata of clay,sand stone, shale, pebbles, boulders etc. by first taking a pilot bore of 140mm / 150mm / 200mm and then enlarging to required dia by direct or reverse rotary mud circulation method,including fuel, labour for drilling, bentonite mud, water required for drilling at the site, contruction of mud pit (water available within a lead of 1.5Km) using rotary rig. -Upto 60 mts depth ending below ground level.

Drilling of borewell any where in Karaikal including tranportation in alluvial soil, sedimentary strata of clay,sand stone, shale, pebbles, boulders etc. by first taking a pilot bore of 140mm / 150mm / 200mm and then enlarging to required dia by direct or reverse rotary mud circulation method,including fuel, labour for drilling, bentonite mud, water required for drilling at the site, contruction of mud pit (water available within a lead of 1.5Km) using rotary rig. - From 60mts and upto 90 mts. depth ending below ground level.

Drilling of borewell any where in Karaikal including tranportation in alluvial soil, sedimentary strata of clay,sand stone, shale, pebbles, boulders etc. by first taking a pilot bore of 140mm / 150mm / 200mm and then enlarging to required dia by direct or reverse rotary mud circulation method,including fuel, labour for drilling, bentonite mud, water required for drilling at the site, contruction of mud pit (water available within a lead of 1.5Km) using rotary rig. - From 90mts and upto 120 mts. depth ending below ground level.

Drilling of borewell any where in Karaikal including tranportation in alluvial soil, sedimentary strata of clay,sand stone, shale, pebbles, boulders etc. by first taking a pilot bore of 140mm / 150mm / 200mm and then enlarging to required dia by direct or reverse rotary mud circulation method,including fuel, labour for drilling, bentonite mud, water required for drilling at the site, contruction of mud pit (water available within a lead of 1.5Km) using rotary rig. -From 120mts and upto 150 mts. depth ending below ground level.

Drilling of borewell any where in Karaikal including tranportation in alluvial soil, sedimentary strata of clay,sand stone, shale, pebbles, boulders etc. by first taking a pilot bore of 140mm / 150mm / 200mm and then enlarging to required dia by direct or reverse rotary mud circulation method,including fuel, labour for drilling, bentonite mud, water required for drilling at the site, contruction of mud pit (water available within a lead of 1.5Km) using rotary rig. -From 150mts and upto 180 mts. depth ending below ground level.

Drilling of borewell any where in Karaikal including tranportation in alluvial soil, sedimentary strata of clay,sand stone, shale, pebbles, boulders etc. by first taking a pilot bore of 140mm / 150mm / 200mm and then enlarging to required dia by direct or reverse rotary mud circulation method,including fuel, labour for drilling, bentonite mud, water required for drilling at the site, contruction of mud pit (water available within a lead of 1.5Km) using rotary rig. -From 180mts and upto 210 mts. depth ending below ground level.

Drilling of borewell any where in Karaikal including tranportation in alluvial soil, sedimentary strata of clay,sand stone, shale, pebbles, boulders etc. by first taking a pilot bore of 140mm / 150mm / 200mm and then enlarging to required dia by direct or reverse rotary mud circulation method,including fuel, labour for drilling, bentonite mud, water required for drilling at the site, contruction of mud pit (water available within a lead of 1.5Km) using rotary rig. -From 210mts and upto 240 mts. depth ending below ground level.

Drilling of borewell any where in Karaikal including tranportation in alluvial soil, sedimentary strata of clay,sand stone, shale, pebbles, boulders etc. by first taking a pilot bore of 140mm / 150mm / 200mm and then enlarging to required dia by direct or reverse rotary mud circulation method,including fuel, labour for drilling, bentonite mud, water required for drilling at the site, contruction of mud pit (water available within a lead of 1.5Km) using rotary rig. -From 240mts and upto 270 mts. depth ending below ground level.

Drilling of borewell any where in Karaikal including tranportation in alluvial soil, sedimentary strata of clay,sand stone, shale, pebbles, boulders etc. by first taking a pilot bore of 140mm / 150mm / 200mm and then enlarging to required dia by direct or reverse rotary mud circulation method,including fuel, labour for drilling, bentonite mud, water required for drilling at the site, contruction of mud pit (water available within a lead of 1.5Km) using rotary rig. -From 270mts and upto 300 mts. depth ending below ground level.

Reaming from 200 mm dia pilot bore to 350mm dia bore. Upto 60 mts depth ending below ground level

Reaming from 200mm dia pilot bore to 350mm dia bore. From 60 mts and upto 90 mts depth ending below ground level

Reaming from 200mm dia pilot bore to 350mm dia bore. From 90 mts and upto 120 mts depth ending below ground level

Reaming from 200mm dia pilot bore to 350mm dia bore. From 120mts and upto 150 mts depth ending below ground level

Reaming from 200mm dia pilot bore to 350mm dia bore.From 150 mts and upto 180 mts depth ending from ground level.

Reaming from 200mm dia pilot bore to 350mm dia bore.From 180 mts and upto 210 mts depth ending from ground level.

Reaming from 200mm dia pilot bore to 350mm dia bore.From 210 mts and upto 240 mts depth ending from ground level.

Reaming from 200mm dia pilot bore to 350mm dia bore.From 240 mts and upto 270 mts depth ending from ground level.

Reaming from 200mm dia pilot bore to 350mm dia bore.From 270 mts and upto 300 mts depth ending from ground level.

Reaming from 300 mm dia pilot bore to 400/450mm dia. Upto 60 mts depth ending below ground level.

Reaming from 300mm dia pilot bore to 400/450mm dia bore. From 60 mts and upto 90 mts depth ending below ground level

Reaming from 300mm dia pilot bore to 400/450mm dia bore. From 90 mts and upto 120 mts depth ending below ground level

Reaming from 300mm dia pilot bore to 400/450mm dia bore. From 120 mts and upto 150 mts depth ending below ground level

Reaming from 300mm dia pilot bore to 400/450mm dia bore .From 150 mts and upto180 mts depth ending below ground level.

Reaming from 300mm dia pilot bore to 400/450mm dia bore.From 180 mts and upto210 mts depth ending below ground level.

Reaming from 300mm dia pilot bore to 400/450mm dia bore.From 210 mts and upto240 mts depth ending below ground level.

Reaming from 300mm dia pilot bore to 400/450mm dia bore.From 240 mts and upto270 mts depth ending below ground level.

Reaming from 300mm dia pilot bore to 400/450mm dia bore.From 270 mts and upto300 mts depth ending below ground level.

Charges for developing the borewells with air compressor of 600 CFM capacity (minimum 8 hours) including transportation labour and fuel charges for compressor and conducting yield test by "V" Notch methods.

Supplying transportation and packing of 8mm size down gauge graded pebbles including filling the annular space gradually complete. The pebbles disintegrated pieces. should be free from any disintegrated pieces.

Supplying,transporting and packing of clay balls including filling the annular space gradually complete.The clay balls should be free from any sand particles.

Providing and fixing M.S. top cover suitable for UPVC pipes including the cost of materials and labour etc.

Providing and fixing of UPVC End Cap embedded in M.S. Cone suitable for UPVC casing pipe including the cost of materials and labour for jointing.

Construction of granular sub-base by providing close graded material, mixing in a mechanical mix plant at OMC, carriage of mixed material to work site, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401of MoRTH specification, 4th Revision - by plant mix method for grading I material.

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC using with concrete mixer at site,laying in uniform layer by manual means in sub-base / base course on well prepared surface and compacting with smooth 3 wheeled steel roller to achive the desired density.

Providing and applying liquid seal coat, type `A' comprising of a layer of bituminous binder, followed by a cover of stone chipping of specified grading and rolling with power roller 8 to 10 tonne. As per clause no 513 of MOST specification.

Providing and laying open graded premix carpet of 25mm thick on prepared surface in a single course as wearing course composed of specified size of stone aggregates premix with a bituminous binder in mini hot mix plant 6-10 tonne laying manually and rolling with power roller 8-10 tonne but excluding cost of primer/tack coat. As per clause no 509 of MOST specification.

Providing and applying tackcoat on the prepared surface, heating bitumen in boiler and spraying the bitumen with sprayset fitted on bitumen boiler - on black topped surface bitumen @ 5kg/10sqm

Providing and applying tack coat on the prepared surface, heating bitumen in boiler and spraying the bitumen with sprayset fitted on bitumen boiler - on granular base such as WBM and WMM surfaces not bitumen primed. Rate of application 10kg/10sqm.

Cleaning of the existing black topped surfaces with brooms, soft brushes and finally dusting with old gunny bags and/or compressed air to receive bituminous treatment. As per clause no 503.3.1 of MOST specification.

Supplying and lowering of UPVC 200mm dia Plain casing pipe confirming to IS.12818-1992 with relevant amendments with class designation CM and with minimum wall thickness of 13.00mm to 14.20mm as per I.S.Code into the bore well with proper vertical alignments etc. Including the cost of materials, but excluding the cost of labour for positioning the assembly for lowering purpose using contractor's rig excluding the hire charges thereof.(out side dia 226.00mm to 228.40mm)

Supplying of UPVC plain casing pipe for bore wells (FINOLEX/JAIN) conforming to I.S.12818-1992 with relevant amendments with class designation ’CM’ and with minimum wall thickness 16.00mm to 18.00mm including transportation and stocking at site 250 mm dia.(out sidedia 282.00mm to 286.00mm)

Providing and fixing in position PVC moulded reducer coupler (Finolex/Jain) (1Mpa) conforming to IS 7834 part II and ISI marked including labour charge for jointing 250x200mm dia.

Providing and fixing in position PVC moulded reducer coupler (Finolex/Jain) (1Mpa) conforming to IS 7834 part II and ISI marked including labour charge for jointing 250x200mm dia.

Reinforced cement concrete work in beams , suspended floors, roofs having slope upto 15 degree landings, balconies, shelves,chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement :1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).