Repair to Kota stone tiling joinery brickwork plaster granite and internal water supply works to certain bldg in Zone II at Mil Stn Jaisalmer

Amount

Taking down chowkats or frames (without taking of shutters from the frames) area not exceeding 1.5 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down chowkats or frames (without taking of shutters from the frames) area exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down shutters of any description not exceeding 1.00 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each complete all as specified & directed by Engineer-in-charge.

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded all as specified & directed by Engineer-in-charge. Note :- To be fixed at any floor level not more than triple storey.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified & directed by Engineer-in-charge. Note :- To be fixed at any floor level not more than triple storey.

S&F, mild steel, angles, bars, flats etc, as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain, angle cleats for securing purlins to wood tress or rafters, knee piece inserts, two way and three way staps, plate washers and silmilar small articles confirming to Fe-290 Gde- E-165 complete all as specified & directed.

S&F, stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperture 1.00mm and fixed with stainless steel wire staples complete all as specified & directed by Engineer-in-charge.

S & F, 35 mm thick second class hard wood factory made plain, framed, panelled shutters (Two panels), with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and Style as per IS:1003 (Part-1), kiln seasoned and chemically pressure treated all as specified & directed by Engineer-in-charge.

S & F, 30 mm thick Second class hard wood factory made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) complete all as specified & directed by Engineer-in-charge.

Hacking out old broken glasses (any thickness, size, quality or description) from steel/wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified & directed by Engineer-in-charge.

S&F 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete including welding if required for fixing in case of pressed steel chowkat all as specified & directed by Engineer-in-charge.

S&F, 3mm thick, sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each panes complete all as specified & directed by Engineer-in-charge. Note :- To be fixed at any floor level not more than triple storey.

S&F, 100mm size, butt hinges, medium weight, cold rolled mild steel including necessary welding if required all as specified & directed by Engineer-in-charge.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified & directed by Engineer-in-charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with single piece extruded PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement of single piece extruded PVC profile for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified & directed by Engineer-in-charge.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm single piece extruded PVC profile with MS square tube, supplying and fixing in opening as per specifications & directed by Engineer-in-charge.

S&F 150 mm size aluminium anodised barrel tower bolts of extruded section all as specified & directed by Engineer-in-charge.

S&F in repair, 200 mm size aluminium anodised barrel tower bolts of extruded section all as specified & directed by Engineer-in-charge.

S&F 150 mm size extruded aluminium handle, fabricated type, anodiesed complete all as specified & directed by Engineer-in-charge.

M&L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified & directed by Engineer-in-charge.

M & L for hardcore of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface.

M&L for PCC 1:2:4, 50mm thick using 20mm graded aggregate as in flooring

M&L for granite stone tiles of any type of 10mm thick (600mmx300mm) machine cut as in floor/skirting/ dado laid over 15mm thick screed bed/ backing coat in cement mortar (1:6) and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified & directed by Engineer-in-charge.

M & L non skid ceramic vitrified coloured tiles exterior grade but exc 0.18 sqm and n.exc 0.38sqm (600mm X 600mm) ,8-10mm thk including scrrd bed or bedding layer 15mm thk in CM 1:6 all as specified.

...ditto…. but as in skirting, steps etc in vertical surfaces with 10mm thick backing coat in CM 1:4

M & L for hardcore of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface.

M&L for 25 thick sand cushing for laying of precast concrete interlocking tiles including watering and consolidation complete.

M & L for 60mm thick inter locking cement concrete mixed colour factory made paver blocks M-35 designation (compressive strength) laid over 25 mm thick sand cushion to maintain the slope including compaction with 75 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base etc.

S & F Table top Wash hand basin white, including cutting for and pinning ends of brackets or erecting stand.((Model : Jaquar Cat No: JDS-WHT- 25909)

S&F bevelled edged looking mirror 8mm thk all as specified and directed by Engr- In-Charge.

S& F in repair Health faucet with 1.5 M Stainless Steel flexible Tube with Hook (Prayag Cat Part No- BEA-41)

M&L for ceramic tiles exterior grade 300 x 300 x 10mm (Endura from Johnson or equivalent) including screed bed in CM 1:4, 15 mm thick set and jointed in neat cement slurry and pointed in coloured cement to match all as specified and roughening of exc concrete surfaces all as directed

S & Fin repair Wall mounted wash down water closet pan (Pedestal), white (EWC)including fixing bolts, flushing cistern and flushing pipes etc (Model : Jaquar Cat No: SLS- WHT -6201)

S&F solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on and including 5mm thick PVC sheet fillets of width 50mm for wall paneling inclusive of fixing on wall to make frame as per specifications complete all as directed by Engineer-in-charge.

Demolition of cement concrete (un reinforced) in any description and in any position not otherwise specifically provilded.

M&L PCC 1:2:4 type B0 25mm thick as in leveling course in sunken portions

Material and labour for applying cold bituminous primer @ 0.30 ltr/Sqm confirming to IS-3384 and laying APP polymer modified membrane non-woven polyester reinforcement of 3mm thick, weighing not less than 3.5 Kg/Sqm with plain polythene finish and sealing all the over laps of 75mm in length side and 100mm on the width side of membrane by torching the same all as per manufactures instructions and all as specified and directed. Including removing existing unserviceable water proofing treatment and washing down with water to remove all dirt etc. also including 50 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in floors, roof padding & finished the surface even & fair without using extra cement including approved water proofing compound as per manufacturer's instructions or by 3% of weight of cement all as specified.

M&L Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre on concrete surfaces and sanding

M&L rendering 10mm thick in CM 1:4 finished fair and even with WPC @ 3% by wt of cement

Supply only water proofing compound

S&F in repair stainless steel plate rack of size 910mm X 790mm X250mm complete all as specified & directed by Engr-in-Charge.(Make: Silver shine model no 315, Bluestar, Nirali)

S&F in repairs Brass CP ball mixer for mixing hot & cold water screwed down for iron pipe and fixed for 15mm dia bore (Make : Cera Cat part no F2006401, Prayag Cat part no 8275, Hindware Cat part no F-330020)

S&F in repair CP wash basin mixer for mixing hot & cold water screwed down for iron pipe 15mm dia( Make: Hindware Cat part no F3300145-P, Cera Cat part no F2006461, Prayag Cat part no P15-50)

M&L for machine cut kota stone flooring 550 x 550x 20 to 25mm thk laid over cement screed bed jointed & pointed with grey cement slurry mixed with pigment to match the shade including rubbing &mirror polishing including over a screed bed or bedding layer of 15mm thk in CM 1:6 for laying floor finishes all as specified and directed.

ditto above but on verticla surfaces such as skirting /dado etc including over a screed bed or bedding layer of 10mm thk in CM 1:3 for laying tiles all as speciifed.

M & L for Granite (of any type) tiles18 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types in floors including 20 mm thick CM 1:4 for laying granite all as specified.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing, removing serviceable tiles).

M&L for 25mm thk PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in subbase of floors & finishing the surface even & smooth without using extra cement.

M&L for non skid ceramic coloured tiles of size 300x 300 by 7mm thick as in floors set & jointed in neat cement slurry and pointed in coloured cement to match the tiles and including scread bed or bedding layer 15mm thick in CM 1:6 all as specified.

M&L for ceramic tiles exterior grade 300 x 300 x 10mm (Endura from Johnson or equivalent) including screed bed in CM 1:6, 15 mm thick set and jointed in neat cement slurry and pointed in coloured cement to match all as specified and roughening of exc concrete surfaces all as directed

M&L for vetrified ceramic coloured tiles 9 to 10 mm thick area of each tile exc 0.18sqm but not exc 0.38sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement over 15mm thick screed bed in CM 1:6 all as directed (size 600mm to 600mm)

...ditto…as per item no 52 above. but as in skirting, steps etc in vertical surfaces with 10mm thick backing coat in CM 1:4

M & L non skid ceramic coloured tiles 7-8mm thick(square/rectangular) area of each tile exceeding .11Sqm but n.exc .18Sqm in floor set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6.

M & L glazed ceramic coloured tiles (450x300mm)x 7mm thick joint free in dado/skirting set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 etc.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L for 75mm thk cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in subbase of flooring/hard standing as specified

M & L for 60mm thk, M 35 grade machine pressed precast concrete interlocking paver block rubber mould using grey cement and no pigment of any shape and size conforming to IS 15658 - 2006 laid overincl 25mm thk sand cushoining complete.

S & F rubber moulded chequered cement concrete tiles 20cm X 20 cm X 25mm thk with grey cemnt and pigments,set jointed in neat cement slurry as in floors/path etc over and including 15mm thk screed bed in CM 1:4 complete.

M&L for PCC 1:2:4, 100mm thick using 20mm graded aggregate as in flooring.

M& L for PCC 50mm thk type C1 1:3:6 (20mm graded stone aggregate laid in alternative as in plinth protection including finished the surface even and fair without using extra cement and filling the joints with mastic filling ie one part of bitumen 85/25 & 3 parts of sand by weight

Demolition of stone masonry built in cement mortar incl coping of any description all as specified and directed.

M&L squared rubble walling Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 all as specified.

ditto - as per item No 63.00 but except stone

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses all as specified.

M & L for Keyed pointing to rubble masonry uncoursed or brought up to courses in cement mortar 1:4.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. loaded bedded and pointed in any mortar

M & L for Granite (of any type) tiles18 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types

M&L for machine cut kota stone flooring 550 x 550x 20 to 25mm thk laid over cement screed bed jointed & pointed with grey cement slurry mixed with pigment to match the shade including rubbing &mirror polishing including over a screed bed or bedding layer of 15mm thk in CM 1:6 for laying floor finishes all as specified and directed.

ditto above but on verticla surfaces such as skirting /dado etc including over a screed bed or bedding layer of 10mm thk in CM 1:3 for laying tiles all as speciifed.

M&L sand stone slabs 5 cm thk in sunshades ,chajjas ,shelves ,cills landings, cover stones ,templates etc

Demolistion of precast concrete articles and precast concrete block walling built in cement mortar or cement lime mortar of any thickness or as directed by Engr-in-Charge

M&L Precast cement concrete block masonry with solid blocks PCC 1:3:6, type C1 exc 10cm in width and setting in CM 1:6

Taking down cement plaster on brick/stone/concrete surface including wall tiling or terrazo finish and hacking out joints hacking for key scrubbing down with water etc complete

M & L rendering 10mm thick on surface of stone masonry or surface other than fair face of brickwork in CM 1:6 all and it is to be finished even and smooth without using extra cement all as specified

M&L for rendering 15 mm thick on stone masonry surfaces or surfaces other than fair faces of brick work or on one side of lathing in cement mortar 1:4 & finished the surface even & fair without using extra cement all as specified.

M&L for rendering 5 mm thick on fair faces faces of brick work or concrete surfaces of ceilings in cement plaster 1:3 & finished the surface even & fair without using extra cement all as specified.

M & L preparation of new plastered surfaces and applying three coat of white wash on walls complete

M & L preparation of new plastered surfaces and applying three coat of white wash on ceiling

M & L for two coats of cement base paint over a coat of white wash on walls

S&F in repairs aluminum anodised /power coated partition wall of aluminum section 100mm x 44mm x 2mm thick frame rectangular section and panel of PVC sheet or prelaminated board in bottom panel and 5.5mm thick sheet glass in top panel with rubber lining and aluminum beading around length including necessary fixing arrangement for bottom and top member of aluminum frame in floor/PCC/Brick work as per site requirement with rawl plug etc, including chromium plated steel screws 60cm centre to centre all as specified and directed by Engineer-in-Charge (Note : Cost of PVC panel or prelaminated board and sheet glass shall deemed included in the unit rate of this item )

Supply fabricating and fixing in repair of aluminium door powder coated of extrusion aluminium section including frame work complete, consisting of frame vertical and horizontal members, of size 104mmx44.45mmx1.8mm thick. Vertical style of door shutter of size 85mmx44.45mmx1.8mm thick. Top, middle and bottom rial of size 85mmx44.45x1.8mm thick and fixing 5 mm thick plain/tinted sheet glass of Modi guard/Atul or prelaminated particle board 9 to 10mm thick of make Kit Ply with aluminium bedding and rubber gasket/beading including frosted film as desired fixing of hydraulic floor spring one in single leaf or two nos in double leaf door of Make Kelvin/Evershine. One mortice lock for aluminium door (each) and two aluminium tower bolts for each door. Fixed with rawl plug including rectification of floor/wall to match the existing surfaces. All as specified and as directed by Engineer-in-Charge at site. (Cost of sheet glass/frosted film & sun control film shall be included in the unit of this item)

S&F of powder coated aluminum sliding window comprising of sliding runner of three way (track), consisting of two sliding shutter duly fitted with 5.0 mm thick galss and one shutter duly fitted with stainless steel wire cloth of 0.36 mm nominal dia of wire & average width of aperature 1.4 mm with and incl necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc and down push type locking arrangement in glass shutter, incl necessary fixing arrangement i.e. rawl plug etc, complete all as directed. Make of Section : Jindal / TATA / Hindalco.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty approved by Engr-in-Charge

Dismantling (AC corrugated , semi corrugated etc ) AC sheets in roof coverings complete all as specified & directed by Engineer in charge.

S&F Pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet/ semi corrugated 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws as specified.

Dismantling wrought iron or mild steel work of any description not othervise provided for

S &F Rolled nild steel framed work as in door or gates of angle or other section confirming to Fe - 410-S with gusset plates, rail braces etc complete drilled for fixing of steel sheeting or other covering and hanging and fixing complete.

S & F Joist, channel,angel or tee sections, fixed independently , without connecting plates etc

M & L preparation of new steel surfaces exc 10cm in width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer primer

S&Fin repair vitreous china squatting pan orissa pattern complete of size 580 x 440 mm white with intagral foot rest and making good to the floor complete fixed in repairs.(Cera Cat part No-53010102, Hindware Cat Part No.- 20042)

S & F in repair Vitreous china wash down water closet pan(Pedestal pattern), white (EWC)with necessary P/S Trap and fixed in repairs including jet spray and seat cover(Cera Cat Part No-S1050104, hindware cat Part No-20011)

S&F in repair PVC seat cover black/white closed pattern with flat bottom and mild steel CP or aluminium hinging device complete( Make: Cera Cat part no B1510107,Hindware,Parryware)

S&F in repair bib taps 15 mm dia of cast, copper alloy cp with crutch or butter fly handle screwed down screwed for brass ferrule or iron pipe and fixed in repairs.(Prayag Cat Part No.- 8306, Cera Cat Part no. -F 2006151, Hindware Cat Part No. -F 330003, Silver shine model no:-1001)

S&F in repair two way bib taps 15 mm dia of cast, copper alloy cp with crutch or butter fly handle screwed down screwed for brass ferrule or iron pipe and fixed in repairs.(Prayag , Cera, Hindware , Silver shine )

S & F in repair hand shower for bathroom with Hook & 1.5 Meter Flexible Chain etc

S&F in repair pillar taps 15 mm bore cast copper alloy with capstan head chromium plated screwed down high pressure with or without 'Hot' & 'Cold' with long screwed shanks and fly nuts, screwed fixed in repairs.(Prayag Cat Part No.- 8304, Cera Cat Part no. -F 2006101, Hindware Cat Part No. -F 33002,Silver shine model no:-1065)

S & F in repair Stop valve fancy type cast copper alloy chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm dia

S & F in repair 20mm stop cock fancy typ cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends or for unions etc

S&F in repair PVC low level white flushing cistern syphonic action type 10 ltrs capacity incl flush pipe 32 mm dia incl PVC connection 450 mm long and complete fixed in repairs. Make Prayag,Cera Cat Part No-B1010102, Hindware)

S&Fin repair wash hand basin vitereous china flat back size 550 x 400 mm white incl CP waste coupling waste pipe brackets complete fixed in repairs.(Cera -52030103, Hindware -10017)

S & F in repair for pressure jet for western type water closet with PVC connection 600 t0 900 mm long including brass head screw and suitable washer.

S & F in repair 600 mm long PVC connection pipe of 15mm bore with PTMT nut at both ends complete.

S&F in repairs Vitreous china urinals with urinal spreader, full stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing (Cera Cat Part No- 54020102,Hindware Cat Part No-60002)

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store

-Ditto- All as per ser No 105.00 but 20mm dia

S & F 15mm dia medium grade GI tubing with all fitting and fixed to wall, ceiling or laid in floors etc

-Ditto- All as per ser No 107, but 20mm dia

Dismantling water tanks and removing to store (exc 250 and not exc 500 ltr capacity)

Dismantling water tanks and removing to store (exc500 and not exc 1000 ltr cap)

S&F in repair 500 ltrs capacity white colour three layer rotational moulded polythene water storage tank (Cylinderical vertical with closed top) hoisted and fixed in postion all as directed by Engg-in-Charge

-Ditto- All as per ser No 111.00 but 1000 ltr capacity.

S & F in repair 20mm bore dia ball brass valves high pressure ,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and complete all as specified and as directed by Engr-in- Charge.

S & F in repair Chromium plated tubular aluminium anodised 60 cm long towel rail 20mm dia D type complete fixed with screws etc.

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm (Make : Silver shine SSSBSD-55,Bluestar, Nirali, Cera Cat part no B4512204)

S & F in repair 32 mm dia., Waste fittings, brass chromium plated for glazed ware sinks, wash basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end

M & l for Cutting chases pinning in for concealed water tubing etc and making good cutting not exc 10cm in width or girth to brick stone wall or concrete surfaces

S&F in repair shelf of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleats

S & F in repair Sheet Glass Shelf Assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long

S&F in repair Swivel shower rose 75mm size with arm 195mm long with bend of 45 degree with flange of PTMT any colour fixed in repairs.(Prayag Cat Part No-BS-38,Cera Cat Part No-F7020102,Silver shine model No- 935)

S & F in repair Soap dish, chromium plated as per sample approved by Engineer-in-Charge.

S&F powder coated mild steel peg stay set of 05 nos of pegs all as specified and approved by Engr-in-Charge

Dismantling Trellis work (Jafri), including taking as under of battens in trellis (posts and rails measured separately)

M&L for 35mm thick precast cement concrete louvers and jallies type C-0 (1:3:6) using 12.50mm graded aggregate (measured solid), including all mouldings but excluding frame, set in cement mortar 1:4 all as directed.

M& L plain cement concrete 1:2:4 type B 1 using 20mm graded stone agregate cast in situ kerb stone ,copings,bed plates ,water through and the like including wethering ,slightly rounded or chamfered angles and throating including use of form work (straight or curved ) set in CM 1:4 complete all as specified and as directed by Enginneer in charge

S & F in repair 300 mm, Mild Steel ordinary rat tail rod pattern springs including roller and roller plate complete

S&F in repair 140 mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drwn steel spring, fixed in floor complete as directed by Engr-in-Charge.

S&F in repair Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed

M & L for repair in Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm- 45gms/40mm-60 gms) of any size or as directed by Engr -in-Charge

S&F in repair Grating doom 100mm dia of PTMT (Minimum weight 25gms)

Dismantling boarding, any description, fixed in any position with nails

M&L for exposed GI frame/grid system duly powder coated for module size of 600 x 600 mm suitable for fixing ceiling tiles, having main T runner of 24 mm size, suspended at 1200mm C/C and cross T runner of 24 mm size, suspended at 600mm C/C with interlocking arrangements to form grid of 600 x 600mm, perimeter runner/channel of 15 mm size, main and cross T runner supported by 4mm dia GI rod from slab / roof, wall angle etc with and including all fixing accessories and making good of distrubed wall surfaces with POP and one coat of oil emulsion distemper, as required to match the existing surfaces, complete all as directed. Make: Armstrong, Gypboard,Dexune, Anchorlam Anchor (Note : The rate quoted by the tenderer shall include fixing in position of ceiling tiles however these ceiling tiles shall be measured and paid for separetly under respective item herein after as supply only).

Supply & fixing of false ceiling in step (s) comprising of 12 mm thick Gypsum board including GI frame work for seamless ceiling made of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 M length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including two coats of plastic emulsion paint complete all as directed. Make: False Ceiling - Armstrong /gypboard/ Anchorlam Anchor. Gypsum Board: Gyproc/ lafarge boral /India gypsum (Note : The measurement shall be made from wall to wall without considering step(s)/overlap at steps)

S R ENTERPRISES

M/s Shree Construction Company

Shubham Builders

S.D. And Company

BHAGWATI CONSTRUCTION

MARUDHARA CONSTRUCTION COMPANY