REPAIR/ REPLACEMENT OF ROOFING SHEET ,FALSE CEILING ,LEAKAGE SEEPAGE WATER PROOFING TREATMENT AND OTHER ASSOCIATED WKS AT SEWAR FORT and PARADE

Amount

Taking down cement plaster of any description etc including racking out joints,hacking for key, scrubbing down with water all as specified & directed by Engr-in-Charge.

Rendering 15 mm thick in CM (1:4) on fair faces of brickwork or concrete surfaces finished fair & even by using M-crushed sand/river sand on External surfaces

Ditto as above item No 2 but in CM (1:6) finished even and smooth without using extra cement.by using M-crushed sand/ River sand on internal surfaces

M&L for rough cast plaster mixture consisting of fine`manfucture washed sand mixed with coarse aggregate(6 to 10 mm) and cement in ratio of 1:1:1 over and in plastic state including 10 mm thick rendering in cement and manfacture washed sand mortar 1:3 on fair faces of bricks masonary or concrete surface of wall complete

Preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer with hand roller complete all as specified.

M & L Preparation of new decorated plastered unplastered surfaces surface of wall including cornices, pilasters etc by brooming down and applying two coats of distemper oil emulsion white or tinted over a coat of white wash with hand roller complete all as specified and as directed by Engr-in-Charge.

M & L Preparation of old distempered surface of wall including cornices etc by brooming down, steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots removing nails and filling small holes by putty and rubbing surface by sand paper to prepare the surface and applying one coat of distemper oil emulsion using hand roller white or tinted complete all as specified and as directed by Engineer-in-Charge.Make NEROLAC/DULUX/BERGER

M&L for Preparation of old decorative concrete, plastered/ un-plastered surface of wall including cornices, pilasters etc by brooming down, steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots removing nails and filling small holes by putty and rubbing surface by sand paper to prepare the surface and applying one coat of cement based paint using hand roller of approved colour complete all as specified and as directed by Engineer-in-Charge.Make NEROLAC/DULUX/BERGER

M&L for two coats of Apex ultima exteriar paint on new plastered surfaces of walls, white or tionted including preparation of surfaces complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings,dressed stone work and precast concrete articles all as spd and directed by Engr-in-Charge.

M&L Brick work with sub class 'B' old size bricks bricks straight or cured on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkats or frames n. exc 1.5 sqm each with shutters (without taking off shutters from the frame). complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkats or frames exc 1.5 sqm but n exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as specified and as directed by Engineer-in-Charge.

Taking down shutter of any description area exc 1 sqm and n. exe 2 sqm complete all as specified and as directed by Engineer-in-Charge.

S&F for 30 mm thick Flush Shutters, Solid core construction, Single or double leaved rebating shall be square or splayed, with block board core and plywood face panels free from twist or wrap in plane, both face is covered with decorative face venner with Intenal wooden frame lipping not less than 50 mm complete all as specified and as directed by Engineer-in-Charge.

Providing and fixing in repair12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete all as specified and as directed by Engineer-in-Charge. (Door handle, lock and stopper etc.to be paid separately).

S&F 35 mm thick 2nd class hardwood( hollock ) factory made plain framed, panelled shutters (any No. of panels) with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces size of members as per SSR Part-I complete all as specified and as directed by Engineer-in-Charge.

S&F 35 mm thick 2nd class hardwood ( hollock ) factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc.( without sash bars ), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified in SSR Part I. complete all as specified and as directed by Engineer-in-Charge.

S&F steel ventilator with top hung shutter including hinges,steel peg stay, handle complete all as specified and as directed by Engineer-in-Charge.

M&L for rolled mild steel framed work such as grill grating etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors , laddres, door gate frame, framed baliusters, walk ways, railing , frame work of water tank and similar work conforming to Fe-290, Gde-E-165 complete all as specified and as directed by Engineer-in-Charge.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position complete all as specified and as directed by Engineer-in-Charge.

S&F 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified and as directed by Engineer-in-Charge.

S&F 150 mm long mild steel barrel tower bolts stove enameled black with bright bolt (ISI marked) complete all as specified and as directed by Engineer-in-Charge.

Mild steel presses steel bow handle oval type stove enameled black of size 150 mm (ISI marked) complete all as specified and as directed by Engineer-in-Charge.

S&F MS sliding door bolt, plate type, 300mm long, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts & nuts, 4 on bolt plate and 2 on staple plate and fixed complete all as specified and as directed by Engineer-in-Charge.

Factory made steel window with side hung shutteers including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded including one shop coat of zinc chromas primer complete all as specified and as directed by Engineer-in-Charge.(Note :- Mild steel wire cloth shall be measured and paid separately under respective items)

All as per item No 26 above but without glazing bars complete all as specified and as directed by Engineer-in-Charge.

Providing and fixing in repair factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately)

Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension complete all as specified and as directed by Engineer-in-Charge.

S&F in repair for 20 mm thick pvc shutter, printed one side with one coting of ultra violet chemical, glossymat finish inc 100% termite/water proof, fireretrandenteco friendly. Weight not less than 12 kg per sqm complete all as specified and as directed by Engineer-in-Charge. Make HR enterprise/ Alstone

S & F in repair kitchen cub board 20 mm thick pvc board of any size provided with shelves ,partitions and glass shutters with stainless steel ISI marked fittings as hinges (02 Nos in each shutter), handles (01 No in each shutter ),fancy Knobs (01 No in each shutter) & magnatic locks and any other fittings required ,shape/pattern complete all as specified & directed by Engineer -in -Charge.

M & L 0.80 mm thick PVC edge binding tape arouond the mm thich PVC shutter edge, complete all as specified and directed. Make :HR Enterprises / Alstone

S & F in repair stainless steel plain basket of size 17 " x 20" x 6", complete all as specified and directed. Make : Home care / Silkmove/ HATIC

S & F in repair stainless steel partition of size 17" x 20"x6", complete all as specified and directed. Make : Home care / Silkmove/ HATIC

S & F in repair stainless steel cutlery of size 17" x 20"x6", complete all as specified and directed. Make : Home care / Silkmove/ HATIC

S & F in repair stainless steel grain trolly with stand f size 21"x 17"x 10" complete all as specified and directed. Make : Home care / Silkmove/ HATIC

S & F in repair stainless steel cup soucer of size 17" x 20"x 4", complete all as speified and directed. Make : Home care / Silkmove/ HATIC

S & F in repair stainless steel plate basket of size 17" x 20"x6", complete all as specified and directed. Make : Home care / Silkmove/ HATIC

S & F in repair 20" long telescopic slider to fiacilitate drawer slide on stleel ball bearing fixed with steel screws complete all as specified nd directed.Make : Home care / Silkmove/ HATIC

S & F in reapair mild steel continous(Piano) hinges, bright finish or electra galvanized, width of flag (when open) 30mm complete all as specified and as directed by Engineer-in-Charge.

S & F auto hinges for cabinet case complete all as specified and as directed by Engineer-in-Charge.. Make : Karf/ Hetch/ Homecare

S & F 150mm size stailess stelel bright finish handle for cabinet shutter complete all as specified and as directed by Engineer-in-Charge.

S & F in reapir Triple corner wire shelf with 100 % stainless steel ,non - magnatic, multilayer chrome plated , argon welded for optimum utilization of unbuilt space and convenience of handling frequently used goods complete all as specified & directed by Engineer -in -Charge. .Make Life time -code : CW-02 Tier,Tier-2/3 or equivalant make

S & F in repair Triple corner glass shelf with 100 % stainless steel ,non - magnatic, multilayer chrome plated , argon welded for optimum utilization of unbuilt space and convenience of handling frequently used goods .complete all as specified & directed by Engineer -in -Charge. Make Life time -code : CG-02Tier ,Tier2/3 or equivalant make

Providing & fixing in repair in position stainless kitchen Dish rack plate cutlery stand of size (30"X30"),fixing on wall including all its fixtures all complete as per direction of the Engineer in-charge.

M&L dismantling floor,heart or wall tiling including cement mortar bed(but not backing) , removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engineer-in-Charge.

M&L Glazed ceramic in patches coloured/printed tiles in vertical surface of size 300x200x7mm/450x350x7mm thick set and jointed in neat cement slurry, over 15mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed by Engineer-in-Charge.

M&L for Light shade Vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-Charge.

M&L for Dark shade Vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-Charge.

M&L for White/ Coloured shade of Glazed ceramic tile in vertical surface exc 0.15 Sqm but nexc 0.25 Sqm each tile of 7-8 mm thick set and jointed in neat cement slurry and pointed in white coloured cement to match complete all as specified and as directed by Engineer-in-Charge.

M&L for Highlighter designer pattern of Glazed ceramic tile in vertical surface exc 0.15 Sqm but nexc 0.25 Sqm each tile of 7-8 mm thick set and jointed in neat cement slurry and pointed in white coloured cement to match complete all as specified and as directed by Engineer-in-Charge.

M & L for non skid ceramic coloured tiles 7 to 8 mm thick area of each of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in skirting/ risers of steps etc set and jointed (joint free) in neat cement slurry and pointed in coloured cement, incl rendering 10 mm thick in CM (1:4) and finished rough, incl taking down cement plaster on walls etc complete. Make: H & R Johnson/kajaria complete all as specified and as directed by Engineer-in-Charge.

Dismantling of stone slab and tiles of any description or thickness in floors, etc.complete all as specified and as directed by Engineer-in-Charge.

Providing and fixing 20 mm thick Granite of any colour and shade gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete all as specified and as directed by Engineer-in-Charge.

Supply Only neosprene rubber beading suitable for aluminium door / window panels complete all as specified and as directed by Engineer-in-Charge.

S&F EPDM rubber strip of width 2 cm suitable for 1mm to 2 mm gap , fixed with adhesive like Fevicol pasting alongwith blue tag type nails complete all as specified and as directed by Engineer-in-Charge.

S&f for 4.80 mm thick sheet glass with solar control film 25 micron reflective type sticked to glass pane ,odinary qulity and glazing with neosprene beading exc 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

M&L for Sheet glass ordinary quality 3 mm thick and glazing with oil putty in square n. exc 0.50 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

Galvanised mild steel wire cloth 0.50 mm nominal dia if wire and average width of aperature 1.18 mm and fixed with tinned tacks or galvanised wire staples complete as directed by Engineer-in-Charge.

Dismantling wall and ceiling boards ( fibre, pulp, insulation ,etc. ) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed by Engineer-in-Charge.

S&F GI snap grid frame work of size 600 x 600 mm for false ceiling including necessary notching. The snap grid shall consist of GI Main Tee and Cross Tee of size 35 x 25 x 0.7 mm, Main Tee suspended from the soffit @ 1200mm c/c with level clips, Cross Tee inserted/fixed into the slots of main T @ 600 mm to form a grid. The snap grid (main/cross tee section) shall be supported at ends all along the wall with GI angle of size 25 x 25 x 0.7 mm fixed to wall with suitable arrangement, fixed in grid support with 2.50 mm dia plain mild steel wire galvanised class 3 fixed in detached works etc to support snap grid, made of GI as per specification complete all as specified and as directed by Engineer-in-Charge.

S&F 4mm thick Everest designer E-Board fixed or laid/inserted to timber/GI/Aluminium ceiling frame work with screws complete all as directed by Engr-in-Charge

10 mm thick square edge fully perforated GRG(Glass Fibre Reinforced Gypsum) false celing tiles of Size 595x595 mm complete all as specified and as directed by Engineer-in-Charge.

M&L in Repair for removing old deteriorated finishes on ceiling by burning /grinding on old sand stone surface and finish even & smooth with rubbing by sand paper, filling all joints lime mortar with adhesive & complete sealed using colour pigment to match with existing sand stone surface (including complete scaffolding and cleaning all surrounding ) complete all as specified and as directed by Engineer-in-Charge.

M&L in Repair for removing old deteriorated finishes on floor & wall by burning /grinding on old sand stone surface and finish even & smooth with rubbing by sand paper, filling all joints lime mortar with adhesive & complete sealed using colour pigment to match with existing sand stone surface ( cleaning all surrounding ) complete all as specified and as directed by Engineer-in-Charge.

Cutting, polishing existing Kota/ marble floor flooring,(three cuttings and mirror polishing) including Manson polishing, levelling certain places to Kota/ marble floor ,necessary repair work complete as directed By Engineer-in-Charge at site complete all as specified and as directed by Engineer-in-Charge.

M&L for providing Square/Rectangular,raised platform of hight 20 cm below the tank and base dia min 100 MM projected by the external dia all around of tank for pvc cylendrical tank of capicity 500/1000 liters using pcc 1:3:6 type C1 using 20 mm graded stone aggregate with smooth finish including necessary form work etc. complete all as specified and as directed by Engineer-in-Charge.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed by Engineer-in-Charge.

S&F 2 mm dia Mild steel wire 40x40 mm welded mesh, made up into mattress or cages,lapped wired and laid in position including closing after filling complete all as specified and as directed by Engineer-in-Charge.

Dismantling asbestos cement (corrugated or semi corrugated) sheets in roof coverings complete all as specified and as directed by Engineer-in-Charge.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections,ms pipe) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A' complete all as specified and as directed by Engineer-in-Charge. .

S&F rolled mild steel Hollow section square or rectangular of wall thickness 3.25 to 4.25 mm thick, work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections,ms pipe) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A' complete all as specified and as directed by Engineer-in-Charge.

M&L for mild steel work as in wind ties for roof covering including securing bolts etc. including all necessary drilling, bolting or riveting etc and similar work conforming to Fe 290 Gde E-165 all as specified and directed by Engineer-in-Charge.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410W Gde E-250 quality 'A' complete all as specified and as directed by Engineer-in-Charge.

S& F in reapir Pre painted galvalume alumimnium zinc coating GI based corrugated steel sheet 0.50 mm th, sheeting of any colour having strength of 550 mpa as in roof covering etc, complete all as specified and as directed by Engineer-in-Charge.

M&L for fixing in repair 10 mm thick hollow section polycorbonate sheet suppoerted with ribs any colour shade including notched aluminium strip not less than 32 mm wide both edges and with packed with rubber gasket at joints, finaly sealed with silicon gel complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc fixed with ‘L’ hooks complete all as specified and as directed by Engineer-in-Charge.

S&F in repair asbestos cement two pieces adjustable serrated ridge, 6 mm thick for corrugated or semi-corrugated sheets with 'L' or 'J' hooks complete all as specified and as directed by Engineer-in-Charge.

Fixing only asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc fixed with ‘L’ hooks complete all as specified and as directed by Engineer-in-Charge.

M&L fixing in repair for Powder coated Manglore tiles profile sheet aluminium zinc coating GI based corrugated steel sheet 0.45mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge.

Dismantling boarding of any description, fixed in any position with nails complete all as specified and as directed by Engineer-in-Charge.

S&F in repair for PVC wall panelling in repair with panel of 300 mm x 6 mm Hollow section of Sintex pattern SPUF- 146 or equivalent , fixed with PVC plug and screw and inserted to next panel groove, edges and corners of all door/ window/openings etc to be covered with PVC ange fixed with solvent cement complete all as specified as manufacturer's Instructions

M&L 25 mm thick cement concrete type B-0. 1:2:4 (12.5 mm graded aggregate) stone aggregate a in sub base for stone flooring complete all as specified and as directed by Engineer-in-Charge.

M&L Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engineer-in-Charge.

All as per item No 86 but thckness 12-15 mm above as in skirting,dado,riser of step etc. complete all as specified and as directed by Engineer-in-Charge.

M&L for cutting chases , pinning in , making good to facing where required and pointing in CM 1:3 to end or edges for concealed water tubing exc 10 cm but nexc 20 cm girth complete all as specified and as directed by Engineer-in-Charge.

Dismantling and taking up or down the existing unserviceable GI pipe and M&L for new galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors of following sizes :- (a)15 mm bore

(b)20 mm bore

25 mm bore

S&F for in repair Brass Chromium plated single lever basin mixture without pop wastewith 450 mm long braided hoses complete all specified. (Make;- ESSCO cat part no APR 10101B or equivalent)

S&F for in repair Brass Chromium plated pillar cock with 450 mm long braided hoses complete all specified. (Make;- ESSCO cat part no APR 10101 or equivalent)

S&F for in repair Brass Chromium plated Wall mixture 3 - in - 1 system with provision of both hand shower & overhead shower with 115 mm long bend pipe incl connecting leg and wall flange complete all specified. (Make;- ESSCO cat part no APR 101281 or equivalent)

S&F for in repair Brass Chromium plated with swing spout (wall mounted model) sink mixture incl connecting leg and wall flange complete all specified. (Make;- ESSCO cat part no APR 101309 N or equivalent)

S&F for in repair Brass Chromium plated two way Bib cock with wall flange complete all specified. (Make;- ESSCO cat part no APR 101041 or equivalent)

S&F for in repair Brass Chromium plated long body Bib cock with wall flange complete all specified. (Make;- ESSCO cat part no APR 101017 or equivalent)

S&F for in repair Brass Chromium plated Angular stop cock with wall flange complete all specified. (Make;- ESSCO cat part no APR 101053 or equivalent)

S&F for in repair Brass Chromium plated Jet spray wit 1 metre PVC tube covered SS covered complete all specified. (Make;- ESSCO cat part no SPE 101463 or equivalent)

S&F for in repair Brass Chromium plated Bottle trap with fully casted body 32 mm bor, 300mm and 125 mm long connecting pipe and wall flange complete all specified. (Make;- ESSCO cat part no ALE-773A2300 x 125 or equivalent)

S&F for in repair Brass Chromium plated Health faucet (ABS body) with 1.2 m long PVC tube covered SS covered and wall flange complete all specified. (Make;- ESSCO cat part no ALE E55-583 or equivalent)

S&F for in repair Brass Chromium plated overhead shower 80 mm square shape single flow (ABS body chromium plated with grey face plate) with 450 mm long coonecting pipe with rubbit cleaning systemand wall flange complete all specified. (Make;- ESSCO cat or equivalent)

S&F for in repair Brass Chromium plated Hand shower multiflow 80 mm round shape with 1.50 m long spiro chrome flex tube & wall bracket onecting pipe with rubbit cleaning systemand wall flange complete all specified. (Make;- ESSCO cat part no SAE 1931SH555 or equivalent)

S&F for in repair Brass Chromium plated Towel rail of grip 600 mm complete all specified. (Make;- ESSCO cat part no AEC 1111 or equivalent)

S&F for in repair Brass Chromium plated Soap dish with polycorbonate plate complete all specified. (Make;- ESSCO cat part no AEC 1133 or equivalent)

S&F in repair viterous china bowl for couple closet WC with PP soft close seat cover, Hinges fixing accessories and accessories set , 375mm x 665mm x 755 mmof S trap 110 mmalongwith cistern complete all as specified(Make;- ESSCO combination cat part no MVS-WHT-75155 and MVS-WHT-7515N,SS or equivalent)

S&F in repair viterous china Table top basin with CP waste coupling , 435mm x 375mm x 130 mm complete all as specified(Make;- ESSCO cat part no ECS-WHT-933 or equivalent)

S&F in repair viterous china Counter top basin Oval shape with CP waste coupling , 530mm x 445 mm x 195 mm complete all as specified(Make;- ESSCO cat part no ECS-WHT-601 or equivalent)

S&F in repair viterous china Wall hung basin with CP waste coupling and angle iron bracket & screw, 515mm x 415 mm x 195 mm with combination of pedastal complete all as specified(Make;- ESSCO combination cat part no ECS-WHT-805 and ECS-WHT-301 or equivalent)

Providing and fixing in repair Granite Stone of approved shade slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Providing and fixing in repair white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

S&F in Repair One urinal basin with 5 litre white P.V.C. automatic flushing cistern complete all as specified

M&Lin repair of cast iron nahani trap of 75mm bore, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified

Demolition & breaking up drain pipes AC, (Salt glazed ware, AC or Reinforced concrete) set in CM Internal dia of pipe 100 mm complete all as specified

S&Fin repair of PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, ISI marked of 75mm bore complete all as specified

S&Fin repair of PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, ISI marked of 110mm bore complete all as specified

S&Fin repair of UPVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, Type 'B', ISI marked of 75mm bore complete all as specified

M&L for painting with two coats of plastic Emulsion paint over primer paints after preparing old painted Brick , stone, concrete, asbestos cement or plastered surfaces complete all as specified

M&L for one coats painting with synthetic enamel paint to old wood or wood based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface including all preparatory work complete all as specified and as directed by Engineer-in-Charge.

M&L for one coats painting with synthetic enamel paint to old steel or steel based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface including all preparatory work complete all as specified

Demolition of cement concrete (unreinforced ) of up to the roof stone slab , any description all as directed by Engineer - in charge.

Demolition of Lime concrete of any description and in any position not otherwise specifically provided for.

M&L for 40mm thick PCC type B-0,( 1.2.4) using 12.5 mm graded stoine aggregate finished even & smooth without using extra cement complete all as specified

M&L for screed bed or bedding layer 15 mm thick in cement mortar 1:4 mixed with water proofing compound as per manufactoring instruction, finished even and smooth without using extra cement over cement slurry over existing roof @3 kg/sqm . WPC Shall be meashured and paid seperatly

Supply only water proofing compound ISI marked complete all as specified Make : DR Fix)

M&L APP based polymeric membrane not less than 3mm thick , weighing not less than 3.5 Kg / sqm , and upper side of membrane thermally insulated with white mineral gravel finish , informly embedded during manufacturing process,shall only be used . It shall be laid by torch application .Side over laps shall be 75 mm and the end shall be 100 mm and all overlaps and joints shall be sealed by torch application including applying a coat of cold applied bitumen primer conferming IS:3384 @0.40 Kg/Sqm complete all as specified

M&L Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the rati of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge

S&F sinks made of stainless steel 1mm thick kitchen or labortory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 1215mm x 460mm, bowl size 410mm x 330mm x 190mm including waste pipe of polythelene of low or high density or pvc 32 mm dia &waste coupling brass chromium plated for 32 mm bore with long screwed shank and fly nuts including making holes in any type of wall for brackets and fixed in cm 1:3 or pcc 1:2:4 type B0 complete fixed in repair .Make of sink -comet/neelkamal/hindustan/devidayal/ kitchenqueen/ jaquar

Dismantling of old U/S grating of any description or size and S&F new CP cockroch trap grating 75/100/125 mm dia of weight not less than 40 gm for floor trap/Nahani trap

Preparation of new or previously untreated steel surface of any description not oterwise described over 10 cm width or girth and appying two coat of synthetic enamel paint over a coat of red oxed prier all as specified and directed. Make: Asian Paint(apcolite)/ Berger paints (Luxoli gloss)/shalimar(Superlac hi gloss)

M & L prepration of new wood or wood based surface of any description over 10 cm widtgh or girth and applying two coats of synthetic enamel paint over a coat of pink primer. Make: Asian Paint(apcolite)/ Berger paints (Luxoli gloss)/shalimar(Superlac hi gloss)

Dismantling 1000 ltr water tank and M&L new 1000 ltr ISI marked rotational moulded polyethylene water storage tanks with threaded lid in white color (cylindrical vertical with closed top) hoisted and fixed in position & including 20mm brass ball valve all as specified in SSR part-I

Dismantling 500 ltr water tank and M&L new 500 ltr ISI marked three layer rotational moulded polyethylene water storage tanks with threaded lid in white color (cylindrical vertical with closed top) hoisted and fixed in position & including 20mm brass ball valve all as specified in ssr part-I

De-vegetation from the bldgs by chemical injection of Round Up (arsenic base) compound and subsequently uprooting by physical means without damaging the historic fabric and structure of the building under strict supervision of conservation Eng-in-charge.

Repair of existing sandstone chajja (of approved quality) (As per existing size length x width 600 to 750 and thikness 50-75 mm) by replacing damaged/ missing stone chajja, wherever required as per old existing design, including cost of dismantling/ making of wall/ parapet where chajja is inserted/fixed following existing design & construction details. Item includes cost of safety measures/ use of specified equipments for workers of building required to complete the work at all heights & including all leads

Repair ,Cleaning and Re-fixing of hanging decorative stone brackets as per old design including patch repair( if any ) and chemical wash( amonia or as approved) with complete length of support stone as per old design ,materials and specification .Item includes cost of shuttering /scaffolding /safety measure /use of specified equipment for workers of building required to complete the work .

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of work

PD GUPTA AND COMPANY