ADDN ALTN TO RATION STAND AT CAMERO COMPLEX PROVISIONING OF ALUMINIUM PARTITION AT GROUND FLOOR OF DIT PROVISION OF TWO WINDOWS ONE EACH IN PW B AND DTE OF E MMS AT AT CSDO PROVISION OF ALUMINIUM GRILL AT 17 WINDOWS AT 1ST FLOOR OF DIT BLDG

Amount

S&F for Anodised aluminium frame (minimum 50 micron powder coating) for doors, windows, ventilators or in partitions with one or more rebates with without sash bar including jointing, cleat glazing clips aluminum mongry etc fixing of sheet glass and particle board complete all as specified and directed by Engr-in-Charge.

S&F 5.5mm thick plain glass ordinary quality and glazing, suare exc 0.50 sqm in each pane as in doors etc complete all as specified and directed by Engr-in-Charge.

S& F 9mm thick prelaminated particle board, interior grade, prelaminated on both sides with decorative choice lamination complete all as specified and directed by Engr-in-Charge.

S&F Aluminium (extruded section) body door closer hydraulically regulated, designation No.3, universal type, suitable for door shutter of 851 to 1000mm in width complete all as specified and directed by Engr-in-Charge.

S&F for Brass Mortice lock, vertical type, size 100mm, 4 Levers complete all as specified and directed by Engr-in-Charge.

Dismantling of ceiling /wall panelling including frame work and board complete all as specified and directed by Engr-in-Charge.

Cutting openings through walls built in cement mortar for door, window and other openings or enlarging existing openings, and making good etc., or cutting out defective masonry for underpinning including providing, fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Use and waste of formwork to chulla hoods, chajjas,troughs and similar item including edges fair finished surface of concrete surfaces complete all as specified and directed by Engineer-in-Charge.

Use and waste of formwork to fair finished surface of sides and soffits of floor or roof beams, beam haunchings, girder, bressummers,lintels,cantilevers ,shelevs incuding supports, overhangs, etc. also splays between floors and beams ,etc complete all as specified and directed by Engineer-in-Charge.

M& L for reinforced cement concrete nominal mix 1:2:4, type B-1 using (20mm graded aggreate) in beams, cantilevers , bressummers, lintels over 1.5m span complete all as specified and directed by Engineer-in-Charge.

M & L for reinforced cement concrete nominal mix 1:2:4, type B-1 using (20mm graded aggreate) in chajjas complete all as specified and directed by Engineer-in-Charge.

M&L for mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and blinding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

All as per item No 12 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed by Engineer-in-Charge.

S & F for aluminum power coated any colour (minimum thickness of power coating 50 micron) aluminium window and ventilator shutters, sliding type, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed by Engr-in-Charge.

S & F aluminium deco grills conforming to DG-104 grade complete all as specified and directed by Engr-in-Charge.

S&F vertical venetian blinds made out of nylon cloth of any clour 100mm wide strip as aprroved including hanging arrangement rollers etc complete all as specified and directed by Engr-in-Charge. Make : MAC / MARVEL / MAX / DECK

M&L Rendering 15mm thick on fair faces of brick work in CM 1:4 mixed with water proofing compound As per manufacturer instruction finished even and smooth without using extra cement complete all as specified and directed by engr-in-charge. Note :- Water proofing compound shall be measure and paid separately)

Supply only water proofing compound ISI marked. Make : Sikka / Fosroc WPC complete all as specified and directed by Engr-In-charge.

M&L for preparation of new plastered or unplastered surface of walls, and applying two coats of cement based paint over a coat of chalk whitningalkali resitant primer complete all as specificed and directed by Engr-in-Charge.

M &L for PVC profile for wall panelling colour / shade as approved size 250mm wide, 08 mm over all thick with 1 mm wall thickness fixed with screw to mild steel square ( size 20mmx 20mmx 1mm thick) tubler frame work including one coat of red oxide primer, fixed to walls complete all as specified and directed by Engr-in-Charge.

M&L for PVC profile corner beading L/T type for wall panelling, colour/shade matching with wall panelling complete all as specified and directed by Engr-in-Charge.

S&F 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed by Engr-in-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,complete all as specified and directedy Engr-in-Charge.

M&L for Cement concrete in foundations, filling and mass concrete type C2 1:3:6 (40mm graded aggregate) complete allas specified and directed by Engr-in-charge.

S&F of Stainless Steel 304 series board of size 2'x2.5' written both side . Board Frame made of SS 304 series 16 gauge 25mm wide. The board shall be sheathed both side with 4mm thick ACP Sheet with reflective tape of blue color high intensity plastic (HIP) 3M on both side , letter shall be written in white color the size is as required, approved by Engr-in-Charge including 01 nos vertical SS post 304 series 50mm dia of pipe, height of 7.5 ft and top mouth closed with SS capcomplete all as specified and directed by Engr-in-Charge.

Removing excavated material n exc 100m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed by Engr-in-Charge.

Demolition of brick work built in CM incl all quoins, pillars etc but excl ashlar facings, dressed stone work and precast concrete

Taking down cement plaster of any description on brick or concrete surfaces of walls or ceiling etc incl. raking out joints ,hacking for key and scrubbing down with water upto 4 storeys building complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced ) of any description and in any position not other wise specifically provided complete all as specified and directed by Engr-in-Charge.

Taking down Door shutter of any description exc. 1.0 Sqm but n exc 2.0 Sqm each incl necessary repair to opening with CM 1:4 complete all as specified and directed by Engr-in-Charge.

Dismantling structural steel work in?cluding doors, gates but excluding framed truss etc complete all as specified and directed by Engr-in-Charge.

Taking out of APP modified water proofing membrane complete on roof surface and surface properly cleaned by wire brush complete all as specified and as directed by Engineer-in-Charge.

M&L for 15 mm thick cement plaster in cement mortar 1:6 on Bk surfaces on fair face of brick work and finished even and smooth w/o using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for 10 mm thick cement plaster in cement mortar 1:3 on concrete or brick surface and finished even and smooth w/o using extra cement as in ceiling complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new surface and applying two coat of distemper on wall complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new surface and applying two coat of white wash on ceiling complete all as specified and directed by Engr-in-Charge.

M&L for brick work with subclass B bricks, straight or curved on plan to any radius built in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection, path/hardstanding/subbase etc complete all as specified and directed by EIC.

M&L for Cement Concrete 1:2:4 Type B-0 (using 12.5 mm graded stone aggregate) as in roof kerb, or mud stops rounded of chamfered on edge complete all as specified and directed by Engineer-in-Charge.

M&L for 55mm thick PCC 1:2:4, type B-0 using 12.5 mm graded stone aggregate laid as in padding complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of plastered/concrete surfaces of roof and applying the under mentioned course of roof treatement complete all as specified and directed by Engineer-in-Charge.:- (a) Surface shall be throughly wire brushed, cleaned, washed, dried up properly and apply evenly a bituminuous primer coat conforming to IS @0.4 ltr /Sqm over concrete / plastered roof surface. (b) Applying evenly a tack coat of bitumen 85/25 grade @1.20 kg/ sqm. (c) Laying of 3mm thick APP membrane sheet (min weight 3 Kg/Sqm) consisting of a core of 160 gms/Sqm polyster non woven fabric mat protected on both sides with a high quality polymeric asphaltic mix again protected with thermo fusible HMHDPE FILM on dried primed surface by torch application method. APP membrane will normally be laid in length at right angle to the direction of slope. The over lap shall be minimum 100mm on longitudinal direction and 150mm on the transverse direction including cuttings, grooves etc. (d) Membrane bonded completely to the substrate & the over laps are then scaled/fused by flame. (e) 15mm thick screed bed as in CM 1:4 complete all as specified. (f) including 2 coats of almn paint on APP membrane. Note:- This treatement shall be done by the approved authorized applicators and guarantte of treatement shall be for 10 years.

M&L Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, Ditto, with riveted, bolted or welded attachment conforming to grade Fe-410 -W(Gde E-250) quality-Ball complete all as specified and directed by Engr-in-Charge.

M&L Rolled mild steel section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors ; fixed with angle cleats or other connecting plates conforming to grade Fe 410-W,all as specified.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide 0r zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth,complete all as specified and directed by Engr-in-Charge.

M&L gunniting to RCC works in column beams, slabs, landing, balconies etc by removing loose concrete including plaster cleaning of surfaces with wire brushes and applying epoxy, paint anti corrosive coating of minimum 40-50 microns thick with sikatop Armatec 108 or Colusal VL of MC Bauchemie to rusted steel reinforcement after removing cleaning all rust by sand/grit blasting and supply and fixing welded steel wire mesh 75mm x75mm with 3mm dia steel wire and similar works etc and expoxy based or other equivalent suitable bonding against treatment to be carried out on old concrete surface with Sikadur 32 of Sika. Nito bond EP of fosroc or equivalent (as per manufacturers instruction) to bond old and new concrete mixing @ 3% by weight of cement polycrete and providing gunniting with a minimum pressure of 2.5 Kg sqcm and applying gunniting 30mm thick in cement mortar (1:2) and including 15mm thick plaster in CM1:4, 1mm thick wall care putty, applying two coat of snocem and extra reinforcement as if required, complete all as specified and directed by Engr-in-Charge.

M&L for prepration of old plastered or unplastered surfaces of walls and applying one coat of cement base paint , complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new surface and applying two coat of white wash on walls complete all as specified and directed by Engr-in-Charge.

S&F 30 mm thick Flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides, including preparaion of surface and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engr-in-Charge.

S&F 250mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed by Engr-in-Charge.

S&F 100mm long Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, typeB-11 complete all as specified and directed by Engr-in-Charge.

S&F 150mm long Brass handles, cast type, polished bright complete all as specified and directed by Engr-in-Charge.

Supply and fixing windows/ ventilators fabricated from 0.60mm thick roll formed section made of galvanised steel powder coated (Base steel as per IS-513"D" quality) galvanised as per IS-277 with ZINC of 120GM/SQM . Windows /ventilators having frame suitable for dual shutter i.e. inner and outer shutter with grill, glazed shutter with 4.0mm thick glass, mesh shutter with 32 gauge stainless steel mesh, 6mmx12mm flat iron with 10mm square bar M.S. grill and all fitting, fixtures accessories complete as specified and shown in drawing No CEAF/STD-191/2014, sheet 1/2 & 2/2 dated 11.12.14(4000 series), complete all as specified and direted by Engr-in-Charge. Note : (i) Glazed shutter with 4.00mm thick glass, Mesh shutter with 32 gauge stainless mesh and M.S. grill as per Note above mentioned drawing deemed to be inclusive in the rate quoted for unit. (ii) Glass, stainless steel mesh will be fixed to window by authorised rep of manufacture of window only. (iii) Including 2 coats of synthetic enamel paint over a coat of red oxide complete.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and 20mm thick screed bed in cm 1:4 complete and including dismantling of stone slabs complete all as specified

Demolition and breaking of 100mm dia drain pipes (salt glazed ware, AC or reinforcement concrete) set in cement mortar complete all as specified and directed by Engr-in-Charge.

S&F 110 mm dia bore PVC (SWR) bends, including removing for concrete and refixing with 1:2:4, type B1 (20 mm graded aggregate) or in 1:3 cement mortar complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) 110 mm dia bore pipe single socketed, in any length with rubber ring joints fixed to walls, including necessary PVC clamps for fixing of pipes.

M&L for brick work with sub class 'B' brick , half brick thick wall built in CM 1:4 straight or curved on plan to any radius with old size bricks complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new plastered surfaces and applying two coats of exterior acrylic emulsion paint premium quality over a coat of primer incl 3mm thick wall care putty on walls/ceiling complete all as specified and directed by Engr-In-charge.

J D ENTERPRISES