COMPLETION OF INCOMPLETE WORK FOR PROVN OF OTM ACCN PH I AT LEIMAKHONG UNDER GE LEIMAKHONG

Amount

Dismantling plain or corrugated steel sheeting, any gauge, thickness including nainital or similar pattern roof covering complete all as specified and directed.

Taking down chowkhats/frames with shutters (without taking off shutters from the frame) etc, not exceeding 1.50 Sqm each and stacking at site complete all as specified and directed.

Taking down chowkhats/frames with shutters (without taking off shutters from the frame) etc, exceeding 1.50 Sqm but not exceeding 4.00 Sqm each and stacking at site complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp or insulation, etc) any thickness including cover fillets complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section, in any position (Unframed work) complete all as specified and directed.

Dismantling framed steel truss MS work as in roof truss not exceeding 10 m span complete all as specified and directed.

Dismantling structural steel work including door, gates, rafter, purlin, etc. complete all as specified and directed.

Demolition of Brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 150 mm thickness (below or above ground level) complete all as specified and directed.

Surface excavation in hard/dense soil n exc 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed.

Rough excavation n exc 1.5 m deep in hard/dense soil and getting out complete all as specified and directed.

Excavating over areas not exc 1.5m deep and getting out in soft/loose soil complete all as specified and directed.

Excavating over areas not exc 1.5m deep and getting out in hard/dense soil complete all as specified and directed..

Excavating over areas exc 1.5m but not exc 3.0m deep in soft/loose soil complete all as specified and directed.

Excavating over areas exc 3.0m but not exc 4.5m deep in soft / loose soil complete all as specified and directed..

Excavating over areas exc 3.0m but not exc 4.5m deep in hard/dense soil complete all as specified and directed..

Excavating over areas, exc 1.5 m deep but n exc 3.00 m and getting out in hard/dense soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc1.5 m in depth and getting out in hard/ dense soil complete all as specified and directed..

Excavating in trenches n exc 1.5 m wide n exc 1.5 m deep in soft/ loose soil for foundation etc or for shaft, wells, manholes etc n exc 10 sqm on plan and not exc 1.5 m in depth and getting out complete all as specified and directed.

Excavating in trenches n exc 1.5 m wide , exc 1.5 m deep but n exc 3.00 m deep in soft/ loose soil for foundation etc or for shaft, wells, manholes etc n exc 10 sqm on plan and exc 1.5 m deep but n exc 3.00 m deep and getting out complete all as specified and directed.

Excavating in trenches, n exc1.5 m wide, exc 3 m but n exceeding 4.5m in depth; for foundation, etc. or for shafts, wells, cesspits manholes, pier holes, etc. nexc 10 sq m on plan and exc 3.00m but not exc 4.50 deep and getting out in soft lose soil complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed

Returning ,filling in including spreading ,levelling watering and well ramming in soil in layers n exc 25 cm thick complete all as specified and directed

Supply and spreading sand cushioning for under ground cable protection with dry fine river sand complete all as specified and directed. Note: Punned thickness shall be measured and paid.

Removing excavated material (soil) not exceeding 50 m distance and depositing where directed at a level n exc 1.5 metre above the starting point complete all as specified and directed .

Removing excavated material (soil) exc. 250 m but n exc. 500 m and depositing where directed complete all as specified and directed .

M&L for hardcore with broken stones of gauge n exc 63 mm , deposited, spread and levelled in layers n exc 15 cm thick watered and rolled/ rammed to a true surface complete all as specified and directed.

Loose filling with broken bricks aggregates of gauge 80 to 150 mm in soakage pilts, wells complete all as specified and directed.

Loose filling with aggregates of guage 20mm complete all as specified and directed.

M&L for cement concrete type C1 1:3:6 (using 20 mm graded stone aggregate) as in foundation for erection of bollard light complete all as specified and directed.

Providing precast cement concrete type C-1 1:3:6 in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, lintleblocks, ancho-rage blocks, bonders (for stone walling). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar 1:4 complete with joints to match all as specified and directed.

M&L for Cement concrete, (1:5:10) type E2 (using 40mm graded aggregate)as in foundations filling and mass concrete complete all as specified and directed.

Plain cement concrete M-10 (Nominal Mix) using 20mm graded stone aggregate as in surface channels and drain complete all as specified and directed.

M& L Cement concrete 1:2:4 Type B 2 (using 40 mm graded stone aggregate) ,as in foundations, filling and mass concrete complete all as specified and directed

M& L Cement concrete 1:4:8 Type D 2 (using 40 mm graded stone aggregate), in foundations, filling and mass concrete complete all as specified and directed

M& L Cement concrete 1:3:6 Type C-2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed

Providing cement concrete 1:2:4 Type B-1 (using 20 mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed

Providing precast cement concrete 1:2:4 type B1 in PCC bonders and setting in cement mortar 1:6 complete all as specified and directed.

M&L for precast cement concrete in cover slabs for manholes, chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces using 1:2:4 type B1 (20 mm graded stone aggregate) & set in cement mortar 1:4 complete all as specified.

M & L for Providing precast cement concrete type C0 1:3:6 louvres and jallies, 25mm thick (mea sured solid), including all mouldings and set in cement mortal 1:4 complete all as specified and directed.

M & L for Providing precast cement concrete M-25(Design mix) for cover slab and set in cement mortal 1:4 complete all as specified and directed.

M & L For RCC in Nominal mix Type B1 1:2:4 ( 20 mm grade stone aggregate) for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M & L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed

M& L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregate) as in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

M& L for Reinforced cement concrete M-25 (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M& L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregate)as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

M& L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregate)as in columns, pillars, piers, posts and struts complete all as specified and directed

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement, including forms, moulds, mitred/ stopped ends etc. complete all as specified and directed

Supply only for Liquid water proofing compound.

Supply only WPC (Integral water proofing compound)

M &L Brickwork with subclass 'B' old size bricks, straight or curved on plan exc 6m mean radius built in Cement mortar 1:4 complete all as specified and directed

M &L Brickwork with subclass 'B' old size bricks, straight or curved on plan exc 6m mean radius built in Cement mortar 1:6 complete all as specified and directed

M&L Brickwork with subclass 'B' bricks, old size brick straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed

M&L Continuous brick edging; using sub class 'B' brick (old size) with width equal to the width of the brick; laid dry on end vertically complete all as specified and directed

M&L for Polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sqm complete all as specified and directed.

Broken glass coping in cement mortar 1:3 on top of walls complete all as specified and directed.

Materials and labour for brick protection cover to underground cables with sub class ‘B’ over burnt brick (old size bricks, locally available best quality), laid dry and flat abutting each other with gaps not exceeding 10mm complete all as specified and as directed.

Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted , built in cement mortar 1:6 complete all as specified and as directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and jolints, as specified, of random rubble walling, uncoursed or brought uptocourses not exceeding 40mm depression (Granite or Trap stone) complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; fair finished surfaces of concrete flat complete all as specified and directed

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter fair finished flat surfaces complete all as specified and directed

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) fair finished flat surfaces complete all as specified and directed

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished surfaces of concrete flat complete all as specified and directed

Formwork to sides of square,rectangular or polygonal pillars, posts, struts, piers, columns and stanchions in fair finished surface complete all as specified and directed

Formwork to sides of square, rectangular or polygonal pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete flat complete all as specified and directed

M&L 2nd class hardwood sectional area exc 13 Sqcm but n exc 25 Sqcm plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads complete all as specified and directed

S&F 30mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); and fitted to chowkats complete all as specified and directed

S&F 35mm thick 2nd class hardwood rail and style plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed

S&F 2nd class HW small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n exc 200 cu.cm each complete all as specified and directed

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, and fixing in the frame at site as per specification & drawing complete all as specified and directed

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed

S&F 200 mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, complete all as specified and as directed

S&F 150mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed

S&F 200mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed

S&F 300mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed,complete all as specified and directed

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed.complete all as specified and directed

M&L for 50mm butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F Butt hinges of 75 mm size, medium weight, cold rolled mild steel and fixed, complete all as specified and directed

S&F Butt hinges of 100 mm size, medium weight, cold rolled mild steel and fixed, complete all as specified and directed

S&F 100mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed

S&F mild steel 300mm, ordinary rat tail rod pattern spring, including roller and roller plate complete all as specified and directed

S&F 150mm mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed

S&F 100mm long Aluminium handles, cast type, anodised complete all as specified and directed

S&F 150mm long Aluminium handles, cast type anodised complete all as specified and directed

S&F 2 lever brass Mortice lock, vertical type, size 100 mm complete all as specified and directed

S&F 100mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed

S&F 150mm (overall length of cover plate) floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring complete all as specified and directed

S&F for harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed.

S&F chromium plated fancy type Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed

S&F galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed

S&F Stainless steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F framed work such as grills gratings, etc., with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed baluster; walk ways; railings; framed work of water tanks and similar work conforming to Fe 290, Gde E 165 including pintle hinges, stops, hand-made sliding bolts, etc. for ornamental and intricate design complete all as specified and directed

Mild steel angle posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or rivetting etc, and similar work conforming to Fe 290 (Gde E-165) complete all as specified and directed.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed

S & F Mild steel screw bolts 12 mm dia (machine made ) with hexagonal or square heads with wahser and one hexagonal or square nut ,exceeding 10 mm not exceeding 15cm long complete all as specified and directed

M&L 1mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

MS round bars 12mm dia and over ,cut to length ,bent to shape required including cranking for fixing of chain limk fencing conforming to Gd.I 432 (Part-I) complete all as specified and directed.

M&L Mild steel TMT bars of Grade 500D 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild steel TMT bars of Grade 500D 6 to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild steel TMT bars of Grade 500D 5mm dia and over upto and including 10mm dia cut to length, bent to shape required in stirrups, spacers and binders and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed

M&L rolled sections as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, Fe-290(grade E-165) complete all as specified and directed.

M&L for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 290 (Grade E-165) complete all as specified and directed.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 290 (Grade E-165) complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 including rounded and chamfered complete all as specified and directed

Fixing only chain link fencing including line wires, any mesh size and type of standards, rails , straining bolts , etc. including provision of building wire complete all as specified and directed

Galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm specing and straining and fixing to any type of standard rails straining bolts including ,securing or tying at crossings with and provision of galvanised MS wire,staple or steel pins ,etc as directed(each line wire to be measured) complete all as specified and directed

S&F 1.25 mm thick laths Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete; push pull or manual type complete all as specified and directed

S&F for Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete all as specified and directed

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc. complete all as specified

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.) suitable handle (1 No.) complete all as specified

S&F for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.

S&F anodised aluminium snap grid of size 605 x 605mm frame work for false ceiling complete all as specified and directed

S&F Gl frame work for seamless ceiling of size 605 x 605mm comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed

Supply only Chain link MS galvanized fencing , any size of type complete all as specified and directed

Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F plain, Aluminium sheeting 0.71mm thick, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete all as specified and directed.

Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified and directed

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and directed.

Providing and fixing laminated gypsum board of size 600x600x9.5mm wiht PVC film on face, side and metalized polyester film on back side with all four edges sealed with PVC film of plain white colour in ceiling fixed to GI grid frame as per manufacturers instructions complete all as specified and directed

M&L 12mm thick Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and directed

M&L for 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

M&L for 12mm thick veneered particle board, solid core, exterior grade, with decorative face veneers both faces complete all as specified and directed.

M & L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , complete all as directed and as specified by Engineer-in-charge. Note: cement screed bed shall be measured and paid separately

M & L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , complete all as directed and as specified by Engineer-in-charge. Note: cement screed bed shall be measured and paid separately

Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed Note: cement screed bed shall be measured and paid separately

M&L for Mirror polishing on marble/granite/Kota stone/ stone work where ever required to give high gloss finish complete all as specified and directed.

100 mm thick plain cement concrete(1:2:4) type B-2 using 40 mm grade stone aggregate as in floor finished even and smooth without using extra cement and making impression of expanded metal whilst the concrete is green complete all as specified and directed

M&L for 75mm thick cement concrete type C2 1:3:6 using 20 mm graded stone aggregate as in sub base complete all as specified and directed

M&L for 75mm thick cement concrete type C2 1:3:6 using 20 mm graded stone aggregate as in plinth protection including finishing cement concrete surfaces even and smooth without using extra cement complete all as specified and directed

M&L for 100mm thick cement concrete type C2 1:3:6 using 40 mm graded stone aggregate as in sub base of floor including finishing cement concrete surfaces rough finish by brooming complete all as specified and directed

M&L for 40 mm thick cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) in sunken floor sub base complete all as specified and directed.

M&L for 40 mm cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) in floor including finishing cement concrete surface even and smooth with using extra cement complete all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed Note:Screed bed shall be measured and paid separately

Non - skid Ceramic (coloured) tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed Note: Screed bed shall be measured and paid separately

Non - skid Ceramic (coloured) tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed Note: Screed bed shall be measured and paid separately

Chequered cement concrete tiles 20cm x 20cm x25mm thick with mixture of white & grey cement in equal propotion & no pigment set jointed and pointed in neat cement slury complete all as specified and directed Note: Screed bed shall be measured and paid separately

Rendering 10 mm thick in Cement Mortar 1:4 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra cement) complete all as specified and directed

M & L for rendering 15mm thick in CM 1:6 on fair faces of brick work/ concrete surface complete all as specified and directed

M&L for rendering 15mm thick in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces, finished fair and even complete all as specified and directed

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finishing even and smooth without using extra cement for internal surfaces complete all as specified and directed

M&L for rendering 15mm thick Cement plaster with (1:4)cement mortar to other than fair faces of brick wall and finished ,even & smooth(without using extra cement) using WPC @ 2% by wt of cement for external surface complete all as specified and directed

M&L for rendering 20 mm thick on fair faces of brickwork or concrete surfaces in cement mortar (1:4), finished the surface even and smooth without using extra cement complete all as specified and as directed

M&L rendering 5 mm thick on fair faces of concrete surfaces in CM 1:3 finishing even and smooth without using extra cement on ceiling complete all as specified and directed

M&L for screed bed or bedding layer of mortar 20mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed

M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed

M&L for screed bed or bedding layer of mortar 10mm thick in cement mortar 1:3 for laying floor finishes complete all as specified and directed

Raised pointing to random or polygonal rubble, uncoursed or brought upto courses masonry in cement mortar 1:4 complete all as specified and directed

M&L for preparation of surfaces plastered or unplastered new surface of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed

M&L for preparation of surfaces plastered or unplastered new surface of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed

M&L for preparation of surfaces plastered or unplastered new surface and applying two coats of oil bound distemper over a coat of primer on false ceiling complete all as specified and directed.

M&L for preparation of surfaces plastered or unplastered new surface of wall and applying three coats of white lime wash complete all as specified.

M&L for preparation of surfaces plastered or unplastered new surface of wall and applying three coats of white lime wash on ceiling complete all as specified and directed

M&L for preparation of surfaces plastered or unplastered new surface of wall and applying two coats of plastic emulsion paint over a coat of primer complete all as specified and directed

Finishing walls with Acrylic Smooth exterior paint of required shade for new work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed

M&L for preparation of new surface of APP membrane and applying two coats of aluminium paint complete all as specified and directed

S&F sheet glass 3mm thick ordinary quality and glazing with oil putty in square n exc 0.50 sqm in each pane complete all as specified and directed

S&F sheet glass 5.5mm thick ordinary quality and glazing with oil putty in square n exc 0.50 sqm in each pane complete all as specified and directed

M&L for prepraration of new or previously untreated surfaces of wood and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

M&L for prepraration of new or previously untreated surfaces of steel and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed

Painting 2 coats of synthetic enamel paint on steel and iron surfaces of any description not exc 10 cm width or girth when unconnected with other painting or when painted in different tint including preparation and one coat of red oxide primer complete all as specified and directed.

M&L for new or previously untreated surfaces and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed

Writing letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high complete all as specified and directed.

Stops, commas, short lines, dashes, hyphens, brackets, etc. complete all as specified and directed.

S&L 25mm tubes, 'medium grade' galvanised, for spout pipe and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&L 25mm tubes, 'light grade' galvanised, for spout pipe and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F 150mm tubes, 'medium grade' galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed

Supply and fixing of 3- layer PP-R ( Polypropylene random copolymer) concealed pipes 20mm outer dia,SDR 7.4 (PN-16) pipe UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

Supply and fixing of 3- layer PP-R ( Polypropylene random copolymer) concealed pipes 25mm outer dia, SDR 7.4 (PN-16) pipe UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

Supply and fixing of 3- layer PP-R ( Polypropylene random copolymer) concealed pipes 32mm outer dia, SDR 7.4 (PN-16) pipe UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

Supply and fixing of 3- layer PP-R ( Polypropylene random copolymer) concealed pipes 63mm outer dia, SDR 7.4 (PN-16) pipe UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors or in trenches etc. complete all as specified and directed.

PP-R (Polypropylyne Random copolymer), Gate valve ( Brass insert) as per rquirement of the site with handle, screwed both ends for PP-R pipes or for unions and fixed of size 25mm complete all as specified and directed.

PP-R (Polypropylyne Random copolymer), Gate valve ( Brass insert) as per rquirement of the site with handle, screwed both ends for PP-R pipes or for unions and fixed of size 32mm complete all as specified and directed.

PP-R (Polypropylyne Random copolymer), Gate valve ( Brass insert) as per rquirement of the site with handle, screwed both ends for PP-R pipes or for unions and fixed of size 63mm complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I, 1000 Ltrs Capacity complete all as specified and directed

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I, 2000 Ltrs Capacity complete all as specified and directed

Bib taps cast copper alloy, fancy type, chromium plated with crutch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe complete all as specified and directed

S&F CP Pillar taps 15 mm bore, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed

S&F CP Pillar taps 20 mm bore, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed

Brass chromium plated superior quality single lever basin mixer for mixing hot and cold water screwed down for union pipe and fixed of size 15mm bore pipe complete all as specified and directed.

Stop valves fancy type,chromium plated with long shank and cup (concealed type), cast copper alloy,screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 25mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 40mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 50mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 20 mm dia ball brass valves high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed

S&F for 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid on ground as in vent pipe complete all as specified and directed.

S&F for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F for PVC (SWR) 75 mm bore vent cowl complete all as specified and directed.

Cast iron Nahani trap/floor trap of 75 dia with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed

M&L for PCC M -10 ( Nominal mix ) using 40 mm grade stone aggregate bed to drain pipes of dia 150mm including packing under and haunching against sides of pipes after they are laid and tested complete all as specified and directed.

M & L for salt glazed stone ware drain pipes 150mm dia, laid in trenches and jointed as specified complete all as specified and directed

Supply and Fixing PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as directed and specified.

S & F for Reinforcement cement concrete pipe of 300 mm bore class NP 2 laid and jointed and tested complete with collars all as specified and directed

Supply and fix , 10 litres capacity, PVC valve less, syphonic action type flushing cistern, low level, white with inlet ball valve float, handle and flush pipe including brackets complete all as specified and directed

Supply and Fixing Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) etc all as specified and directed.

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed

Vitreous China squatting pan of pattern “long pan”, size 580 mm white with ‘P’ or ‘S” trap, front or back inlet and foot rests, any pattern complete all as specified and directed

Vitreous China wash down water closet pan (pedestal pattern), white.including fixing bolts, and flush pipe of polyethelyne of low or high density of PVC, 32 mm dia complete all as specified and directed

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed

S&F 125 mm size brass chromium plated shower rose with or without swivel joints, with long body including fixing to steel pipe or union of size 15mm bore complete all as specified.

S&F chromium plated toilet paper holder complete all as specified and directed.

S & F for Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F Vitreous China wash basin, white, flat back, size 550x400mm including 32 mm brass waste coupling,waste pipe and brackets and including cutting for and pinning in ends of brackets complete all as specified and directed

S&F Vitreous china urinal partition white of size 310x700 mm complete all as specified and directed

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Soling (or sub base)200 mm spread thickness with broken boulders or quarried stone, inter stices filled, surface formed and rolled and consolidated to required gradient and camber with 8 to 12 tonne power roller complete all as specified and directed

M&L for 150 mm thick (compacted thickness) Wet Mix Mecadam (WMM) in two layers with coarse aggregates of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated to gradient and camber required with 8 to 12 tonnes power roller and vibratory roller complete all as specified and as directed by Engineer-In-Charge.

Preparing WMM surfaces by brushing with wire brushes for removing caked mud etc sweeping with broom and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc complete all as specified and directed

Preparation of existing black top surfaces by brushing with with wire brushes for removing caked mud etc sweeping with broom and finally fanning the cleaned surface with gunny bags to remove all loose dirt, etc complete all as specified and directed

Applying evenly a priming/tack coat with bituminous primer at 10 kg per 10 Sqm on road surface using paving bitumen complete all as specified and directed. Note: bitumen primer shall be issue under schedule 'B'.

Applying evenly a priming/tack coat with bituminous primer at 5 kg per 10 Sqm on road surface using paving bitumen complete all as specified and directed. Note bitumen primer shall be issue under schedule 'B'.

Rolling and consolidating formation surfaces in cutting with power roller ( exc 8 tonne & n exc 12 tonne) complete all as specified and as directed by Engineer-In-Charge.

M&L for premixed bituminous macadam using 4% binder (paving bitumen) laid/rolled and compacted to required gradient and camber (consolidated thickness 75mm or less) complete all as specified and directed.

M&L Bituminous premix asphaltic dense concrete 40mm consolidated thickness with 6% binder (Paving bitumen) content by weight of total mix, rolled and compacted to required camber and gradient with exc 8 to n exc 12 tonne power roller complete all as specified and directed.

Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A'. complete all as specified and directed.

Forming 12 mm thick expansion joints filled with pre formed bituminious filler and top 30 mm primed and sealed with sealing compound grade 'A' , thickness of concrete slab is 100 mm complete all as specified and directed.

Supply, install , testing and commissioning of solar hot water (Flat plate collector) based on indirect transfer of heat of capacity 500 LPD and including all other standard accessories as specified in section 26 of SSR Part-I and as per manufacturers instruction complete all as specified and directed.

Supply and laying and testing of 160mm bore of high density polyethylene pipes (HDPE) as per IS 14333 for sewage line and pressure rating 4 kgf/Sqcm. Material grade of PE 63 and laid in trenches complete all as specified and directed.

S&F Vitreous China wash basin, white, flat back, size 518x415mm including 32 mm brass waste coupling,waste pipe and brackets complete all as specified and directed.

M&L for pre moulded bituminous filler 50-100mm thickness filled in crumple joints as per manufacturers specification complete all as specified and directed.

S&F chromium plated Soap dish complete all as specified and directed.

S&F MS wheel of size 100mm and 10mm thick with ball bearing encase within solid circular inner core greased complete all as specified and directed.

S&F stainless steel Peg set with 3 stays complete all as specified and directed.

S&F 32mm dia flexible waste pipe complete all as specified and directed.

S&F 8mm thick toughened glass including frame fixing in the wall with Stainless steel nut and bolt & necessary fittings as required complete all as specified and directed.

S&F for 12 mm thick toughened glass fixed/openable, fixed in the frame by nuts and bolts including handles, locks with magnet catcher etc complete all as specified and directed.

M&L for 300 X 300 mm heavy duty endura tiles over 20mm thick screed bed in CM (1:4) over 30 mm thick PCC (1:2:4) Type B-1 laid over 75 mm thick PCC (1:5:10) Type E-2 laid over 150 micron polythelene sheet laid over sand layer of 70 mm thick over sub grade complete all as specified and directed.

S & F of single leaf door steel locker of size 530x600x1500 as shown in CESZ Drg No.TD/SZ/472 sheet No. 1/1 complete all as specified and directed.

M&L for applying 2 coats of exterior weather proof paint over a coat of primer on external plastered surfaces of building complete all as specified and directed.

Material & Labour for liquid seal coat, applying evenly binder @ 9.8 kg per 10 sqm blinding with 6.3mm size stone chippings @ 0.09 cum per l0 sqm and rolled to a uniform smooth surface complete all as specified

Supply and fixing solar charger road stud (cat eye ) of size 125 mm x 125mm x 25mm with blinker facility including adhesive solution on the pavement complete all as specified and directed

Supply and fixing of reflective regulatory sign board of size not exc 1.5 Sqm made out of 2 mm thick aluminium sheet face to be fully covered with non metalised microprismatic lens with high intensity reflective sheeting series 3930 and equivalent exposed vertically as approved by engr - in - charge. Letter symbols border etc shall be as per IRC 67 with required colour scheme on the board and with the high intesity grade A . the aluminium sheet to be rivetted to MS frame of angle iron of size 40 x40x 4 mm (minimum ). the board shall be fixed to 1 No 50 x 50 mm (minimum ) Square post made of M. S angle 50 x 50 x4 mm ( minimum ), 4 m long welded to the frame with adequate anti theft arrangment. steel work to be painted with two or more coats of synthetic enamel paint over a coat of red oxide primer and back side of aluminum sheet to be painted with two or more coats of epoxy paint including appropriate priming coat, excavation and PCC for foundation(1:3:6) type C-2 complete all as specified and directed.

Supply and fixing of post delineators made of ABS round body fitted with 2 Nos 100 mm dia high rerflective reflectors and mounted on MS heavy grade pipe of 50mm dia duly powder coated with anti rust, anti theft and 900 mm high with 300 mm embedded in and including PCC 1:3:6 type C2 using 40 mm grade aggregate of size 300mm x 300mm x 300mm with head cap hydraulic machine presseed and hold fast weld mesh, and reflective strips 30 Nos around the pipe in full perimeter all as per MORTH and IRC specification complete all as specified .

Material and labour for point wiring in PVC conduit with two single core 1.5 Sq mm (nominal area) FRLSH PVC insulated and unsheathed,multi-stranded, copper conductor cable in and including suitable size of PVC conduit 20 mm concealed with all fittings and fixing accessories and suitable size GI sunken box for mounting switches, regulator ete including multi-strand PVC insulated unsheathed stranded copper cable as earth continuity conductor of size 1.5 Sq mm and connected to common earth dolly for one light / Fan point controlled by one, one way switch complete all as specified and directed

Material and labour for point wiring in PVC conduit with two single core 1.5 Sq mm (nominal area) FRLSH PVC insulated and unsheathed,multi-stranded, copper conductor cable in and including suitable size of PVC conduit 20 mm concealed with all fittings and fixing accessories and suitable size GI sunken box for mounting switches, regulator ete including multi-strand PVC insulated unsheathed stranded copper cable as earth continuity conductor of size 1.5 Sq mm and connected to common earth dolly for one socket out let 5 Amps 6 pin on independent board complete all as specified and directed

Material and labour for point wiring in PVC conduit with two single core 1.5 Sq mm (nominal area) FRLSH PVC insulated and unsheathed,multi-stranded, copper conductor cable in and including suitable size of PVC conduit 20 mm concealed with all fittings and fixing accessories and suitable size GI sunken box for mounting switches, regulator ete including multi-strand PVC insulated unsheathed stranded copper cable as earth continuity conductor of size 1.5 Sq mm and connected to common earth dolly for one socket outlet 5 Amps 6 Pin on same board with other switches complete all as specified and directed

S & F Industrial socket outlet with box complete all as specified and directed

Supply & fixing modular metal flush box, 3 module complete all as specified and directed

Supply & fixing modular metal flush box, 4 module complete all as specified and directed

Supply & fixing modular metal flush box, 6 module complete all as specified and directed

Supply & fixing modular metal flush box, 8 module complete all as specified and directed

Supply & fixing modular metal flush box, 12 module complete all as specified and directed

Supply & fixing modular white cover plate with frame, 3 module complete all as specified and directed

Supply & fixing modular white cover plate with frame, 4 module complete all as specified and directed

Supply & fixing modular white cover plate with frame, 6 module complete all as specified and directed

Supply & fixing modular white cover plate with frame, 8 module complete all as specified and directed

Supply & fixing modular white cover plate with frame, 12 module complete all as specified and directed

Material and labour for point wiring in PVC conduit with two single core 4 Sq mm (nominal area) FRLSH PVC insulated and unsheathed,multi-stranded, copper conductor cable in and including suitable size of PVC conduit 20 mm concealed with all fittings and fixing accessories and suitable size GI sunken box for mounting switches, regulator ete including multi-strand PVC insulated unsheathed stranded copper cable as earth continuity conductor of size 2.5 Sq mm and connecting to common earth dolly for one 5 pin 15 Amps socket outlet / Industrial socket outlet on independent board complete all as specified and directed

M&L for modular switch 1way, 6 Amps 1 module complete all as specified and directed

M&L for modular switch 1 way, 16 Amps , 1 module complete all as specified and directed

S & F modular socket multipurpose 5 pin 6 Amps 2 module complete all as specified and directed

S & F modular socket multipurpose 3 pin 6/16 Amps 2 module complete all as specified and directed

Switch piano flush type, single pole, one way 5/6 amp, ISI marked, complete all as specified and as directed.

Switch socket outlet 3 pin , 5/6 amp, flush type. ISI marked, complete all as specified and as directed

Switch socket outlet combination 3 pin 5/6 amp and 3 pin 15/16 Amp, universal type, controlled by one switch, ISI marked, complete all as specified and as directed.

Socket outlet 5 pin 5/6 Amps flush type, 240 volts complete all as specified and as directed.

Supply and fixing lamp holder PVC /polycabonate type with cord grip cap suitable for pendent fittings all as specified and directed.

S&F ceiling rose , 3 phase/pvc/polycarbonate, isolated body complete all as specified and directed

S&F Sheet metal enclosure DB TPN 415 Volt 4 way (I/C 4 & O/G 12) double door type with common bus bar at incoming end of outgoing MCBs for fixing MCB complete all as specified and directed

S&F sheet metal enclosure (for DB's when MCBs to be used), single pole and neutral double door, 8 way, 240 Volts in concealed complete all as specified and directed

S&F sheet metal enclosure (for DB's when MCBs to be used), single pole and neutral single door, 2 way, 240 Volts in concealed complete all as specified and directed

S & F MCB SP 6 to 32 Amps 240 Volts 10 KA rating complete all as specified and directed

S & F MCB SP 40 to 63 Amps 240 Volts 10 KA rating complete all as specified and directed

S & F MCB 4 pole 6 to 32 Amps 415 volts 10 KA rating complete all as specified and directed

S & F MCB TPN 35 to 63 Amps 415 volts 10 KA rating complete all as specified and directed

Metal clad plug and socket box type with DP-MCB control 3 pin, 20 A, 250 volts universal type, earth plug with socket and handle arrangement complete all as specified.

S&F exhaust fan any sweep including connection complete with provision of cable from ceiling rose or connector to fan complete all as specified and directed

Sub main wiring with two single core 4 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS 694 marked in and including 20mm dia PVC conduit including 2.5 Sqmm copper conductor cable FRLSH as earth wire complete all as specified and as directed. Note:(Two single core cable and one No. earth wire and one run of conduit shall be measured together as one length)

Sub main wiring with two single core 6 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS 694 marked in and including 20mm dia PVC conduit including 4 Sqmm copper conductor cable FRLSH as earth wire complete all as specified and as directed. Note:(Two single core cable and one No. earth wire and one run of conduit shall be measured together as one length)

Sub main wiring with two single core 10 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in and including 25mm dia PVC conduit including 6 Sqmm copper conductor cable FRLSH as earth wire complete all as specified and as directed. Note:(Two single core cable and one No. earth wire and one run of conduit shall be measured together as one length)

Sub main wiring with four single core 16 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS 694 marked in and including 25mm dia PVC conduit including 10 Sqmm copper conductor cable FRLSH as earth wire complete all as specified and as directed. Note:(Two single core cable and one No. earth wire and one run of conduit shall be measured together as one length)

S & F wall mounted LED light fitting 20W (Min 2000 lumens) cool day light having surge protection of 2KV with wide voltage protection 160-360 V with co-extruded polycarbonate body, 1200mm long complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed.

S & F surface mounting 2 x 20 W LED tube light fitting T8 type with LED tube rod 2x20W (batten and tube rod separate) complete with all other accessories and electrically connecting with 3 core, PVC insulated twisted flexible core of size 0.75 sqmm copper conductor complete all as specified and directed.

S & F wall mounted LED light fitting astra line model, 9W (min 900 lumens) cool day light having surge protection of 2KV with wide voltage protection 160-360 V with co-extruded polycarbonate body, 600mm long complete with all accessiories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed.

S & F decorative wall mounted type LED wall light fitting 10W made of premium material and finish, sleek and modern design and LED light source complete with all accessiories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed.

MCCB 100 amps, 4 pole, breaking capacity 16 KA suitable for operation of 415 volts AC 50 HZ with fixed type all as specified in SSR Part-I including making necessary electric connections complete all as specified and directed.

MCCB 160 amps, 4 pole, breaking capacity 36 KA suitable for operation of 415 volts AC 50 HZ with adjustable type all as specified in SSR Part-I including making necessary electric connections complete all as specified and directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick burried directly in Ground (Earth Pit not less than 2.25 Metre below Ground Level) with top edge of the plate not less than 1.50 Metre below Ground Level, connected with and including Galvanised Earth Strip of size 32x6.0mm by means of Bolts, Nuts, Check nuts and Washers of GI or Steel and connected Earthing Testing Point/Bus-bar with GI 40mm bore (dia) Light grade Protection Pipe, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc. 150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion complete all as per specified and as directed.

Materials and labour for Earthing complete with GI earth plate electrode 60 cm X 60 cm X 6 mm thick, burried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.50 mtr below normal ground level connected to GI earth lead 4 mm dia by means of GI bolts, nuts, check nuts, washers made out of GI/steel, all as shown on electrical plate No 3 of MES schedule part-I, earth lead wire connected to indicated position including 7.5m long 15 mm bore GI pipe for earth wire protection and concrete pit in PCC(1:3:6, C1),Precast RCC cover slab 55 cm x 55 cm x 5 cm with reinforcement of 8 mm dia bar 100 mm c/c bothways including one handle made of 12 mm dia MS bar embedded in pre cast slab and 20 mm bore galvanised iron pipe"medium grade" for watering with GI funnel and wire mesh including charcoal and salt in alternate layers of 15 cm including necessary excavation and earth work in any type of soil and testing on completion complete all as specified and as directed by Engineer in Charge.

S&F earth continuity conductor or main earthing lead of size 4 mm G I wire fixed to wall on battern or recess or chases or Porcelein/PVC insulator or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. including removal of old strips as required complete all as specified and directed.

S&F 25mm bore Rigid non metallic PVC concealed conduit with one run of 2mm dia GI wire including all accessories and fittings complete for incorporating telephone cable/data cable/TV cable etc. complete all as specified and directed.

S & F blank spacer plate for single module complete all as specified and directed.

S & F of decorative wall mounted fitting including 1 x 12W LED bulb powder coated aluminium fixture colour white including providing necessary 0.75sqm copper flexible wire complete all as specified and directed.

S & F building security light fitting new genration energy saving and enviromental friendly long life versatile pressure die cast aluminium housing with acryclic cover as diffuser with IP -66 high power LED light 25W including suitable size of wall bracket and connecting complete all as specified and directed.

Supply and fixing wall mounting fan 400 sweep, fixed on wall including necessary connection of PVC insulated flexible cable for connection from ceiling rose to fan and connecting complete all as specified.

Supply and fixing microprocessor based single phase electronic temper proof energy meter class 1.0 accuracy conforming to IS 13779 CBIP technical report 88 suitable for LT, single phase, 2 wire, 240 volts system, of rating 6 to 32 Amps, with optical communication port for data downloading, authenticated billing information, recording at least 6 months history data for KWH consumption and load survey data for KW/KVA for atleast last 35 days including safe high grade, transparent engineering polycarbonate casing of projecting mounted type, thickness of box to be 2 mm and IP 54 protection complete all as specified.

Bulkhead luminaire LED light fitting 1x9 watt/10 watt (minimum 6000 lumens) with PL-S/2P 9W lamp made of aluminium body and heat resistant, weather proof gasket complete all as specified. .

S & F circular luminaries suitable for 1 x 22W LED complete with all accessories and lamp including electrically connecting up with PVC insulated three core twisted flexible cord of size 0.75sqm copper conductor complete all as specified and directed.

S & F 9 watt LED wall mounted decorative light wall mounting up-down luminaire of metal glass complete all as specified and directed.

S & F low bay luminaire energy saving environment friendly and robust open type vertical high bay/medium bay LED light fitting of 1 x 50W, IP-54 luminaire with high power COB LED has light source complete with fixing arrangement to ceiling truss including necessary cable connecton from ceiling rose to fitting complete all as specified and directed.

S & F of decorative wall mounted with LED bulb 2X9W with metal and glass, colour white including providing necessary 0.5 sqmm copper flexible wire complete all as specified and directed.

Sheet metal enclosure vertically distribution board TPN 415 volts 4 way, double door type and provision for 4 pole MCCB complete with 200 Amps rated vertical insulated busbar complete all as specified and directed.

Supply and fixing modular TV coaxial socket outlet fixed in 1 M box comprising of flush metal box, inner plate and outer cover complete all as specified and directed.

Supply and fixing modular telephone jack RJ-11 white colour fixed in 1 M box comprising of flush metal box, inner plate and outer cover, all conforming to IS 3854:1997 with finger proof terminals with captive screws having front fixing & removing features without removing plates complete all as specified and directed.

Supply and fixing modular telephone jack RJ-45 white colour fixed in 1 M box comprising of flush metal box, inner plate and outer cover, all conforming to IS 3854:1997 with finger proof terminals with captive screws having front fixing & removing features without removing plates complete all as specified and directed.

Fixing only Galvanised steel water tubing 50 mm bore, medium grade with all fittings (such as bends, elbows, tees, short plugs and union etc) and laid in trenche complete all as specified and directed Note.GI pipe will be used under schedule ‘B’ for fixing.

Fixing only Galvanised steel water tubing 40 mm bore, medium grade with all fittings (such as bends, elbows, tees, short plugs and union etc) and laid in trenches complete all as specified and directed Note.GI pipe will be used under schedule ‘B’ for fixing.

Fixing only Galvanised steel water tubing 25 mm bore, medium grade with all fittings (such as bends, elbows, tees, short plugs and union etc) and laid in trenches complete all as specified and directed Note.GI pipe will be used under schedule ‘B’ for fixing.

Fixing only Galvanised steel water tubing 20 mm bore, medium grade with all fittings (such as bends, elbows, tees, short plugs and union etc) and laid in trenches complete all as specified and directed Note.GI pipe will be used under schedule ‘B’ for fixing.

S & F Joint with rubber or fibre board gasket suitable for 150 mm bore flanged pipe complete all as specified and directed

S & F Joint with rubber or fibre board gasket suitable for 200 mm bore flanged pipe complete all as specified and directed

Cutting cast iron pipes 150 mm bore in position for insertion of tees, branches etc. complete all as specified and directed

Cutting cast iron pipes 200 mm bore in position for insertion of new tees, branches etc. complete all as specified and directed

CI bends,tapers, tee pieces(single or double branches) of any type and angle/radius, straight connecting pieces but one end flanged and other end spigot and socketed upto 150mm bore complete all as specified and directed

CI bends,tapers, tee pieces(single or double branches) of any type and angle/radius, straight connecting pieces(all cokets or sockets and spigot) for 200 to 300mm bore complete all as specified and directed

S & F Reflux(Non-Return) valve 150 mm nominal bore cast iron swing check type reflux(Non return) valve and PN-1.6 with by pass valve, ISI marked heavy duty and including ruber gasket,flanged,nuts,bolts & washer all as specified in IS 53122004 complete all as specified and directed

S & F Run lead joints to CI pipes and fittings for 150 mm bore CI pipe complete all as specified and directed

S & F Run lead joints to CI pipes and fittings for 200 mm bore CI pipe complete all as specified and directed

S & F Cast iron pipe with flanged ends centrifugally cast class ‘A’, 200 mm bore in any length laid in trenches complete all as specified and directed

Supply, Install, fixing ,commissioning and testing of TEFC mounted centrifugal type split casing pump set with CI Casing, bronze impellers, C-45 shaft with pumping capacity 250 Cum per hour at 75 metre head, coupled with and including energy efficieny-2 induction motor of suitable capacity and conforming to IS:12615, 415 volts, 3 phase,145o rpm-50HZ, AC supply and suitable for raw water including manufacture’s recommendation with nuts and bolts including anti vibration pads, painting and connection with suction & discharge water main complete with standard fittings and necessary electric connections with PVC insulated industrial heavy duty cable 50 Sqmm(minimum) , 4 core, 1100 volts from starter to pump set(maximum length 3m) complete all as specified and as directed. Notes: (i) Necessary foundation, base frame & bolting required for installation high pump set shall be provided as per manufactures recommendation and the cost for the same shall be deemed to be included in the rates quoted for this item. (ii) The cost of PVC insulated industrial heavy duty cable and all other standard accessories shall be deemed to be included in the rates quoted for this item.

Supply, laying and jointing of ductile iron pipes with spigot and socket ends suitable for push on rubber joint centrifugally cast, class(K-7), Inner side cement lining and outer side metallic zinc/black bitumen coating and any length , laid in trenches of 150 mm bore pipe including push on rubber(EODM) ring with ISI marked complete all as specified and directed

Supply, laying and fixing of ductile Iron fittings suitable flange, spigot & socket pipe complete all as specified and directed.

Supply and fixing of 100mm cast iron air release valve with drilled flanged ends, pressure rating (PN-1) and tamper proof with two air outlets with nuts, bolts and washer and conforming to IS-14845 complete all as specified and directed.

Supply and fixing of 80mm cast iron air release valve with drilled flanged ends, pressure rating (PN-1) and tamper proof with two air outlets with nuts, bolts and washer and conforming to IS-14845 complete all as specified and directed.

Supply and fixing cast iron flanged type foot valve with drilled flanged ends all as per IS:4038 with cast iron stainer, 200mm bore compete all as specified.

S & F Sluice valve cast iron body class PN-1.6 with flanged ends drilled suitable for bore of pipe 150 mm, conforming to IS: 14846 with and including brass spindle, MS bolts, nuts,washer and pair of rubber gasket ISI mark complete all as specified.

M & L MS bends, tapers, tee pieces(single or double branch) any type and angle/ radius and straight connecting pieces but one end flanged and other end spigot and socketed upto 400mm bore complete all as specified and directed

M & L loop type insulator, vitreous porcelain, white, brown or green, small size with overall dimension 65x90 mm, clearance of hole 16mm complete all as specified and directed

M & L galvanized stay strand of size 7/3.15mm complete all as specified and directed

Galvanised stay strand of size 7/2.24mm complete all as specified and directed

M & L stay assembly with 20 dia stay rod and all other accessories as per Electrical plate No 1 complete all as specified and directed

S & F danger notice plate of 1.6 mm thick MS sheet for HT size 20x15 cm vitreous enamelled white, fixed with MS clamps, bolts and nuts complete all as specified and directed

Supply & Fix 150 watts LED flood light to be fixed on exist High Mast poles (3X6 lights) incl connecting wire complete all as specified & directed

Cradles,hexagonal/rectangular, fabricated with galvanised steel wire 3.15 or 4mm dia complete all as specified and directed

Anti climbing device; spikes type fabricated out of M.S bars (round, square and flat) including nuts, bolts, washers and welding in two halves made to shape to suit the cross section of the pole complete all as specified and directed

Loop type insulator, vitreous porcelain, white, brown or green large size with overall dimensions 90 x 140mm , clearance of hole 25.5mm complete all as specified and directed

Test point terminal block made of gun metal or phosphorus bronze size 75 x 75 x 25mm, drilled and screwed including 3 Nos 8mm dia 25mm long hex, head screw complete all as specified and directed

Air terminator, single point aluminium rod 12mm dia and 300mm long fixed on the roof including all fittings complete all as specified and directed

Aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and directed

Supply & fixing of LED street fitting 60x1.20 watt with LED lamp, DI cast aluminium epoxy powder coated housing with heat resistance clear glass cover, suitable gasket and IP 65 protection including all other standard accessories as per manufactures instruction and including fixed on poles with 50mm dia light grade GI pipe(bend to shape) bracket 1.5 mtr long complete with MS flat iron clamp(clamps shall be 50 x 6 mm MS flat) nuts, bolts & washers including painting the clamps with two coat of aluminium paint over a coat of red oxide primer including connection with 0.5 sqmm copper flexible weather proof wire complete all as specified and directed.

Laying, testing and commissioning XLPE insulated screened, PVC bended, armoured electric cable 1100 volts grade 2 core 6 Sqmm complete all as specified and directed NOTE: LT XLPE cable will be issued under schedule ‘B’ free for laying only.

Laying, testing and commissioning XLPE insulated screened, PVC bended, armoured electric cable 1100 volts grade 2 core 10 Sqmm complete all as specified and directed NOTE: LT XLPE cable will be issued under schedule ‘B’ free for laying only.

Laying, testing and commissioning XLPE insulated screened, PVC bended, armoured electric cable 1100 volts grade 4 core 25 Sqmm complete all as specified and directed NOTE: LT XLPE cable will be issued under schedule ‘B’ free for laying only.

Laying, testing and commissioning XLPE insulated screened, PVC bended, armoured electric cable 1100 volts grade 3.5 core 120 Sqmm complete all as specified and directed NOTE: LT XLPE cable will be issued under schedule ‘B’ free for laying only.

Laying, testing and commissioning XLPE insulated screened, PVC bended, armoured electric cable 1100 volts grade 3.5 core 240 Sqmm complete all as specified and directed NOTE: LT XLPE cable will be issued under schedule ‘B’ free for laying only.

Cutting the existing roads/hard standing upto a size not exc 30 cms in width and not exc 60 cms in depth for laying of cable line and making good the damage road/ hard standing as per the existing roads/ hard standing with necessary stone aggregate, bitumen or with PCC M-15 complete all as specified and as directed.

Supply, laying and testing 40mm GI tubing medium grade ISI marked with all fittings laid in trenches for cable protection of following sizes complete all as specified and directed.

Supply, laying and testing 80mm GI tubing medium grade ISI marked with all fittings laid in trenches for cable protection of following sizes complete all as specified and directed.

Supply and fixing GI tubing 25mm bore, 2 m long, medium grade with welded on MS plate size of 75mm x 75mm x 3mm thick at the bottom grouted on bed block made of PCC M-10 of size 300x300x450 mm including 3 mm thick MS cap with complete fixing arrangement for 12mm dia air termination rod complete all as specified and directed.

S&F new generation energy saving and environmental friendly long life 45W LED streetlight made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening seperate driver compartment with IP66 protection and impact resistance of IK07 LED and supply & fixing brackets made of 32mm bore galvanised iron light grade pipe made to shape having overall lenght 1.2 mtr, fixed over the vertical wall through two numbers mild steel clamp of 25 mm width, 3mm thick MS flat strip and four nos nuts, bolts & washers of 12mm dia 150mm long grouted into wall complete all as specified and directed.

S&F Outdoor luminaries elegantly style LED bollard light fitting 1x8 watt new generation, energy saving, environmental friendly, long liff=e aesthetically designed aluminium landscape luminaire for diffused lighting with high power LED as light source with IP 65 proction and fixed on PCC/brick pillar with MS nut & bolts and including connecting up with suitable size of copper conductor cable form junction box complete all as specified and directed. Note:-PCC/ bricks pillar & junction box shall be measured and paid separately.

S & F FRP junction box fixed with MCB SP 10 Amps arrangement complete all as specified and directed.

S&F new generation, post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LED 25W and connecting complete all as specified and directed.

M/S Satish Chand Agarwal

M/S MANGANG RENOVATIONS

RK Enterprises