Construction of additional facilities at ITI Williamnagar in East Garo Hills

20 mm nominal bore

Providing and fixing brass stop cock of approved quality:

Supplying fitting & fixing complete 100mm Bore Well Submersible Pumps- 3 PH (Water Filled) or similar.

Medium Point wiring up to 6 mts (i)With copper conductor

Providing and fixing aluminium tower bolts, ISl marked, anodized (anodic coating not less than grade AC 10 as per lS:1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Bill of Quantities

BOQ item no

Providing and fixing 75 mm high, 50 mm deep and 18 mm thick stone slab table rubbed, edges rounded and polished, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Earth work in excavation by manual/ mechanical means (Hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in charge. (For site preparation)

All kinds of soil

In ordinary rock

In hard rock (Blasting prohibited)

Earth work in excavation by mechanical means upto a depth of 2 m below the existing ground level for foundation, trenches of foundations, footings of columns/ walls, retaining wall, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification of soils.

All kinds of soil (ordinary soil/ hard soil/ dense soil)

In ordinary rock (soft rock/ medium rock/ hard shale)

In hard rock (soft rock/ medium rock/ hard shale) (Blasting prohibited)

50 mm thick cement concrete flooring with concrete hardener topping, under layer 38 mm thick cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1 :2 (1 cement hardener mix: 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, complete.

All kinds of soil

In ordinary rock

In hard rock (Blasting prohibited)

Disposal of surplus earth/ unserviceable material from the work site including loading and unloading complete as directed for a total of 15 km (i.e. 10 km beyond the initial lead of 5 km)

Excavated earth

Excavated rock

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered).

Upto a depth of 1.50 m

Above 1.50 m upto 3.00 m depth

Earthwork in filling (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, including breaking of clods, consolidating each layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

With available excavated earth

Implementation of Emergency Preparedness Plan, Grievance Redress Mechanism, Stakeholder Engagement activities, Traffic Management,etc.

Extra over Item for additional lift of 1.5m or part thereof for all types of soils

Sand filling in plinth in layers not exceeding 150mm in depth including breaking of clods, consolidating by watering and ramming complete as directed (maximum depth 45 cm)

SUB TOTAL

Centering and shuttering including strutting, propping etc. and removal of form for all heights complete and as directed by the Engineer-in-charge.

Shuttering for sides of plain cement concrete work in blinding concrete, plinth protection, copings, sills etc.

Foundations, footings, bases of columns, raft, grade slab etc. for mass concrete (using steel)

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. (using steel)

Suspended floors, roofs, landings, balconies and access platforms, shelves (using steel)

Lintels, beams, plinth beams, girders, bressumers and cantilevers (using steel)

Columns, Pillars, Piers, Abutments, Posts and Struts (using steel)

Stairs/ spiral staircase, (excluding landings) (using timber)

Weather shade, Chajjas, corbels etc., including edges (using timber)

Extra for additional height in centering, shuttering wherever required with adequate bracing, propping etc., including cost of de-shuttering and de-centering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured)

Implementation of Corrective Action Plan

SUB TOTAL

Extra over item No 19.1 above for each subsequent floor or part thereof above the first floor level.

Long point wiring upto 10mts (i) With copper conductor

1 :3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

Providing and laying cement concrete in retaining walls etc. and all works above plinth level such as pilasters, columns, pillars, posts, struts, buttresses, parapets, coping, plain window sills, fillets, sunken floor etc.,, up to first floor level, excluding the cost of centering, shuttering and finishing

Training and Capacity Building

SUB TOTAL

Bill of Quantities for Williamnagar (Hostel Block), East Garo Hills

Providing and laying cement concrete in retaining walls etc. and all works above plinth level such as pilasters, columns, pillars, posts, struts, buttresses, parapets, coping, plain window sills, fillets, sunken floor etc.,, up to first floor level, excluding the cost of centering, shuttering and finishing

1 :2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size)

SUB TOTAL

PLAIN CEMENT CONCRETE (M10 GRADE)

All works up to plinth level

All works above plinth level up to first floor level

Extra for providing richer mixes:

Providing M-30 grade concrete

SUB TOTAL

Supplying, fitting and fixing in position reinforcement bars up to lst floor level, conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (Rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc. and no measurement for the same is required)

Thermo-Mechanically Treated bars

REINFORCED CEMENT CONCRETE (M25 GRADE)

Providing and fixing parallel threaded couplers conforming to ls code on "Reinforcement Couplers for Mechanical Splices of Bars for Concrete Reinforcement-Specification", to reinforcement bars including threading, enlargement at connection by forging, protecting the prepared reinforcement bars and related operations as required to complete the works as per direction of Engineer in-Charge

Coupler for 16 mm diameter reinforcement bar

Coupler for 20 mm diameter reinforcement bar

Coupler for 25 mm diameter reinforcement bar

SUB TOTAL

Brick work with common burnt clay modular lst class bricks in foundation and in plinth:

In Cement Mortar 1:6 (1 cement : 6 coarse sand)

Brick work in cement mortar with first class brick in superstructure above plinth level up to first floor level in all shapes and sizes:

Cement mortar 1:6 (1 cement : 6 coarse sand)

Sub total of Enviroment Management Plan Cost: D

Half brick masonry with common burnt clay (non modular) first class bricks in superstructure above plinth level up to first floor level

Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per ls: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

SUB TOTAL

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement: 6 coarse sand: 12 graded stone aggregate 20 mm nominal size) up to plinth level with:

Cement mortar 1 :6 (1 cement: 6 coarse sand)

SUB TOTAL

Providing and fixing 18 mm thick gang saw cut, mirror polished, pre-moulded and pre-polished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade, area of slab upto 0.50 sqm (For laboratory counter tops)

Providing edge moulding to 18 mm thick marble stone counters, Vanities, etc.„ including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in Charge.

Granite work

Extra for fixing marble/ granite stone, over and above corresponding basic item, in facia and drops of width up to 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to lS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours and shades of any size as approved by Engineer-in-Charge, in walls, skirting, risers of steps and dados, over 12 mm thick bed Of cement mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Normal range

Providing polished Vitrified wall tiles of approved quality, size, shape and thickness not less than 8 mm on walls and skirting over cement mortar bed 10 mm thick in prop.1:3 (1 cement: 3 coarse sand) including cutting where necessary finished with flush pointing with adhesive or white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed.

Normal range

Tree felling

Granite Stone of approved shade

SUB TOTAL

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought trained and fixed in position with hold fast lugs or with dash fasteners of required diameter & length.

With Teak wood/ Sissu wood.

Providing and fixing ISI marked flush door shutters conforming to lS:2202 (Part I) non-decorative type, core of block board construction with frame of lst class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including lSl marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with wooden battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete:

With Teak wood/ Sissu wood - 50 x 20 mm

Providing and fixing 18 mm thick,150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, lS:3087 marked, including top cover of 6 mm commercial ply wood conforming to lS:303 BWR grade, nickel plated M.S. pipe 20 mm dia (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100x40x40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Extra for using veneered particle board conforming to lS:3097 Grade I, in item of pelmet 18 mm thick 150 mm wide.

Particle board with decorative veneering on both sides

Providing and fixing teak wood lipping of size 25x3 mm in pelmet.

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25 mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete:

25 mm dia

Extra over item No 12.2 & 13.0 above for each subsequent floor or part thereof above the first floor level.

1.5 mm thick

SUB TOTAL

Providing and fixing in position collapsible steel shutters with vertical channels 20xl0x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia. steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer

Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered).

Providing and fixing M.S.fan clamp type I or II of 16 mm dia. M.S.bar, bent to shape with hooked ends in RCC slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars, etc. including priming coat with approved steel primer all complete.

Fixed to openings/ wooden frames with rawl plugs screws etc.

Providing and injecting approved grout in proportion recommended by the manufacturer into cracks/ honey-comb area of concrete/ masonry by suitable gun/ pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge

Stirrer mixed Acrylic Polymer of approved make @ 2% of weight of cement used) modified Cement slurry made with non-shrink compound in concrete/ BCC work

Providing and fixing bolts including nuts and washers complete.

REINFORCEMENT WORK

Extra over item 15.0 above for each subsequent floor or part thereof above first floor level.

SUB TOTAL

Normal range (For toilets)

General Note for Flooring :

All Stone flooring should be adequately protected with plastic sheets, POP layer till final polishing & handing over, without any extra payment.

Providing and laying damp proof course with cement concrete in prop 1 :11/2:3 with graded stone aggregate of 10 mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

40 mm thick

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and groute

d with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing soling with stone, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.

Stone Soling, 150 mm

Filling sunken floor with broken brick bats/ stone aggregates and sand including compacting and supplying of materials complete as specified and directed for all levels.

Brick bats

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 :4 (1 cement: 4 coarse sand).

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade Of the slabs, including rubbing and polishing complete

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Extra over item No 21.1 above for each subsequent floor or part thereof above the first floor level.

Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre.

Size of Tile 600 x 600 mm

Providing & fixing decorative high pressure laminated sheet of plain/ wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to lS : 2046 Type S, including cost of adhesive of approved quality

Building1

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg Of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling, grouting and finishing complete as per direction of Engineer-in-charge

SUB TOTAL

Providing & fixing G.I. Hexagonal chicken wire mesh of 19 size of aperture (12mm x 20 gauge) confirming to IS : 3150 at the junction of dissimilar surfaces of brick / block masonry wall and RCC column / beams and the like including necessary "U" nails / screws with cleats for fixing, overlapping, necessary scaffolding etc. complete all as per specification and as directed by the Engineer-in-charge for all heights and all locations.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer

Providing and applying 15 mm thick cement plaster on rough side of single or half brick wall of mix: in cement mortar 1:6 (1 cement : 6 coarse sand) to interior masonry/ concrete wall surfaces

Diluting and injecting chemical emulsion for pre-constructional anti-termite treatment (excluding the cost of chemical emulsion):

Providing and applying 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement: 6 fine sand).

Providing and applying 6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self-curing mortar of approved make as per the direction of Engineer-in-Charge.

Plain cement concrete works in foundation bed for footing steps, walls, brick works etc. below plinth level as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).

Add for plaster drip course/groove in plastered surface or moulding to R.C.C. projections.

Providing and applying 12 mm of cement plaster finished with a floating coat of neat cement of in cement mortar 1:4 (1 cement : 4 coarse sand) to interior masonry/ concrete wall surfaces

SUB TOTAL

Polyurethane (PU) polishing on woodwork with sprayer including sanding, wood filler complete as directed

Long point wiring upto 10mts (i) With copper conductor

PAINTING, OILING, POLISHING, VARNISHING WORKS

Finishing walls with Acrylic smooth exterior paint of required shade, including scaffolding:

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat Of exterior primer applied @ 2,20 kg/10 sqm)

Wall painting with acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

New work (two coats)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

On steel work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

New work (two or more coats)

Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanized iron/ steel works

SUB TOTAL

HD-20; Circular shape 560 mm internal diameter

M.S. Tube

FENCING, SITE DEVELOPMENT & MISCELLANEOUS WORKS

Providing and laying vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to lS:15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Providing and laying tactile tiles (for vision impaired persons as per standards) of size 300 x 300 x 9.8mm having water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20 mm thick base of cement mortar 1:4 (1 cement: 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear

portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing, etc. all complete as specified and as directed by the Engineer-in-Charge any other approved pattern for Ramp areas)

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 in above ground level and removal of rubbish up to a distance of 50 in outside the periphery of the area cleared.

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 in and lift up to 1.5 m in all kinds of soil

Supplying chemical emulsion in sealed containers including delivery as specified.

With borrowed earth/ stone dust carriage upto 5 km

litre

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/ Rm including drilling and plugging holes etc.:

With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/ Rm including drilling and plugging holes etc.:

Treatment of soil under floors using chemical emulsion @ 1 litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor:

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/ Rm including drilling and plugging holes etc.:

Treatment of masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement: 2 coarse sand) to the full depth of the hole:

Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia. holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing

Rectangular shape of 453 x 357mm

Providing and laying 200 microns thick LDPE sheets (conforming to ASTM-D-4397) to serve as a vapour barrier below the plinth, the sheets having overlaps not less than 100 mm longitudinally and 150 mm transversely. The sheets shall be uniform in width and thickness and free from defects such as pin holes, air bubbles, stains etc. The sheets shall be laid flat prior to concreting on a clean broomed surface. The end of the sheets should butt properly against form work or adjacent concrete as the case may be without gaps. The entire work shall be carried out as per manufacturer's specifications/ guidelines and as directed by the Engineer.

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS:10910, on 12 mm dia. steel bar conforming to IS:1786, having minimum cross section as 23x25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacturer's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) complete as per design.

Supplying and fixing C.I. cover without frame for manholes:

560 mm diam

eter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg

SUB TOTAL

Providing and fixing in position weep holes of 75mm diameter made out of UPVC pipes of (4KSC class) of approved make, quality and length upto 500 mm as specified below, including grouting, making good the surrounding surface, cleaning etc. complete

Providing and applying 15 mm thick cement plaster on rough side of single or half brick wall of mix: in cement mortar 1:6 (1 cement : 6 coarse sand) to interior masonry/ concrete wall surfaces

ALUMINIUM WORK

Providing and laying 60 mm thick factory made cement concrete interlocking paver blocks of M-30 grade made by block making machine with strong vibratory compaction, of approved size. design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and placing in position, 100 mm thick factory made machine batched & machine mixed precast RCC rectangular covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia. TMT bars of Fe 500 grade @ maximum 100 mm c/c on both ways, neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick,100 mm wide MS sheet duly painted over priming coat, reinforcement to be welded at edges with MS sheet and providing 2 Nos.12 mm dia. bar for hooks etc. including cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately); using anodized aluminium (anodized transparent or dyed to required shade according to ls:1868, minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door. window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge:

With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Extra for applying additional anodic coating AC 25 instead of AC 15 to aluminium extruded sections.

Felling trees of the girth (measured at a height of 1 in above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.

SUB TOTAL

For fixed portion

Beyond 30 cm girth up to and including 60 cm girth

Note: All the waterproofing treatment shall be executed through a recognized water- proofing agency approved by the Engineer-in-charge. A written guarantee on non-judicial stamp paper shall be submitted by the Contractor for a minimum period of ten years from the certified date of completion for the satisfactory performance of the entire water-proofing system.

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for underground structures as directed by Engineer-in-charge and consisting of :

(i) 1st layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound conforming to lS:2645 in the recommended proportion over the levelling course (levelling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound.

(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions.

(iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 0.008 cum/sqm thoroughly embedded in the 2nd layer.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to ls:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement: 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge:

Providing and placing in position suitable PVC water stops conforming to lS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:

Serrated with central bulb (225 mm wide, 8-11 mm thick)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to ls:733 and ls:1285, fixing with dash fasteners of required diameter and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, and paneling to be paid for separately):

1st layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours.

2nd layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately); using anodized aluminium (anodized transparent or dyed to required shade according to ls:1868, minimum anodic coating of grade AC 15)

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge over the PCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment.

With float glass panes of 4 mm thickness (weight not less than 10 kg/sqm)

Providing and fixing anodized aluminium (anodized transparent or dyed to required shade according to lS:1868. Minimum anodic coating of grade AC 15) sub frame work tor windows and ventilators with extruded built up standard tubular sections of approved make conforming to lS:733 and lS:1285, fixed with dash fastener of required diameter and size.

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for underground structures as directed by Engineer-in-charge and consisting of

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.

All above operations to be done in order and as directed and specified by the Engineer-in-Charge.

Providing & mixing approved pure acrylic based polymer modified waterproofing compound in concrete work of approved brand and quality, mixed with cement in required proportions as per manufacturer's guidelines, specifications and as directed by the Engineer-in-Charge. The product shall comply with IS: 9103 and IS: 2645. The product must be free of chlorides and shall comply with ASTM C494 Type A & D.

Note : 1) Reinforced cement concrete shall be paid separately under relevant item

With average thickness of 120 mm and minimum thickness of 65 mm.

Grading roof for water proofing treatment with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

SUB TOTAL

Providing and making khurras 450 x 450 mm with average minimum thickness of 50 mm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

DOOR AND WINDOW FITTINGS

Hinges

Providing and fixing lS:12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:

Providing and fixing oxidized M.S. double acting spring hinges with necessary screws etc. complete.

Providing and fixing stainless steel (SS-304 grade) friction hin

ges to the side/ top hung windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge

2nd layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours

Providing and fixing aluminium handles, lSl marked, anodized (anodic coating not less than grade AC 10 as per lS:1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing bright finished brass 100 mm mortise latch and lock, lsl marked, with six levers and a pair of anodized (anodic coating not less than grade AC 10 as per ls:1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3 mm thick & 2100 mm long with SS screws etc. complete as per direction of Engineer-in-Charge

(b) Laying brick bats with mortar using broken bricks/ brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1 :5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by the Engineer-in-charge to required slope and treating similarly the adjoining walls up to 300 mm height including rounding of junctions of walls and slabs

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1 :4 (1 cement: 4 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm squares, 3 mm deep

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test

Providing and fixing bright finished brass 100 mm mortise latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete

Providing and fixing 100 mm aluminium baby latch, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.

Providing and fixing aluminium sliding door bolts, lSI marked anodized (anodic coating not less than grade AC 10 as per ls:1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

Rate only

Door closers, stoppers & tower bolts

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with lSI, lS:3564, embossed on the body, door weight up to 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Building

Providing and fixing aluminium hanging floor door stopper, lSl marked, anodized (anodic coating not less than grade AC 10 as per ls:1868) transparent or dyed to required colour and shade, with necessary screws etc. complete

Twin rubber stopper

Window fittings

All above operations to be done in order and as directed and specified by the Engineer-in-Charge

Signages (Door mounted)

SUB TOTAL

Providing & fixing brush finished 16 SWG stainless steel stain finished (SS 304 Grade) signages of specified size, approved make and quality at all indicated locations as per approved shop drawings and as directed by the Engineer-in-charge .

Signages of 200 mm x 200mm size and make and mounted on door / wall, fixed with SS screws including all accessories etc. complete.

SUB TOTAL

Wiring to a power plug as in item No.6 above with 2X4mm 2 including supplying of 15Amp 5 in 1 SS combined with continuous earth wire to a power point complete

HORTICULTURE AND LANDSCAPING

Providing and fixing bright finished brass 100 mm mortise latch and lock, lsl marked, with six levers and a pair of anodized (anodic coating not less than grade AC 10 as per ls:1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing Brass 100 mm mortise latch and lock with 6 levers without pair of handles (best make of approved quality) tor aluminium doors including necessary cutting and making good etc. complete

Providing and fixing 100 mm aluminium baby latch, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete

Providing and fixing aluminium sliding door bolts, lSI marked anodized (anodic coating not less than grade AC 10 as per ls:1868), transparent or dyed to required colour or shade,with nuts and screws etc. complete:

Providing & fixing brush finished 16 SWG stainless steel stain finished (SS 304 Grade) signages of specified size, approved make and quality at all indicated locations as per approved shop drawings and as directed by the Engineer-in-charge

Part A: 415V System

Electrical Works:

Providing, laying, connection, testing & commissioning of the following sizes of 1100V grade Copper conductor armoured underground cable & overall PVC sheathed cable as per ISI code in trenches including the cost of digging of trenches, sand cushioning with laying etc. and refilling the same in layers or by supporting them in walls and all other accessories as required.

With 4 core 16 sqmm

With 3.5 core 50 sqmm

With 4 core 10 sqmm

With 4 core 6 sqmm

With 3 core 10 sqmm

Suspended floors, roofs, landings, beams and balconies (Plan area to be measured) (For total height of 6.60 m (i.e.3.10m over and above the standard height of 3.5 m)

With 3 core 4 sqmm

1:3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) (For cement concrete screed below floors)

Long point wiring upto 10mts (i) With copper conductor

With 4 core 6 sqmm

Medium Point wiring up to 6 mts (i)With copper conductor

Long point wiring upto 10mts (i) With copper conductor

Short Point Wiring up to 3 mts (i)With copper conductor

Part B: Building Electrification

Wiring in looping system with copper PVC cable 250/440 volt grade of size 1.5 sqmm of approved quality using PVC casing capping incluiding 5 amperes switch Indian best quality ceiling rose etc. capable to a highest point

Wiring as in item No.6 above to a Ceiling/ Exhaust Fan Point

Drawing of Main and Sub-main line with DGSD approved VIR or PVC 250/440 Volt grade in PVC casing capping complete with all accessories.

With 2×2.5mm2 Copper Conductor

With 2X4 mm2 Copper Conductor

With 2X6 mm2 Copper Conductor

Drawing 3 phase Main Line 4 wire with DGSD approved VIR PVC cable 660 V grade in casing capping with all necessary accessories

With 4 X 6 sq. mm copper conductor

With 4 X 10 sq. mm copper conductor

Supplying & fixing of Load Kontaket Miniature Circuit Breakers (MCBs)

6 - 32 Amp. SP MCB

40 - 63 Amp. SPN MCB

40 - 63 Amp. TPN MCB

Supplying, fitting & fixing of Load Kontaket Miniature circuit breakers Double Pole (Isolator)

32 Amp DP Isolator

40 Amp DP Isolator

63 Amp DP Isolator

100 Amp DP Isolator

125 Amp DP Isolator

Supplying, fitting and fixing of Residual-current circuit Breaker with Overcurrent protection RCBOs assembled for AC applications upto 63A.

Supplying, fitting and fixing of Moulded case circuit Breaker of the following capacity

4 Poles 16 -63 Amp Capacity

4 Poles 80 -100 Amp Capacity

Supplying, fitting and fixing of SPN / TPN MCB Metal enclosure MCB Distribution box

Supplying, fitting and fixing of SPN / TPN MCB Metal Enclosure Distribution Board

12 Way (8+36) Modules

Supplying, fitting and fixing Metal box of following sizes on surface or in recess with suitable size of Phendie Lamiated sheet cover in the front including painting etc. as required.

75mm x 75mm x 60mm deep

Wiring as in item No.1 complete to a light plug point when fixed on same boad.

Long point wiring upto 10mts (i) With copper conductor

Long point wiring upto 10mts (i) With copper conductor

200mm x 300mm x 100mm deep

Wiring to a power plug as in item No.6 above with 2X4mm 2 including supply

ing & Fitting of 15Amp 5 in 2 SS combined with continuous earth wire to a power point complete

250mm x 300mm x 100mm deep

Supplying fitting and fixing LED fittings of different wattage,surface or recess or pole mounting, direct or indirect luminair square or round shape also suitable for porch lighting etc.fitted with mirror reflect or complete with all neccessary accessories.

Supplying fitting and fixing complete polish brass bracket, 16mm dia and 23cm long with cast backplate and brass lamp holder with LED lamp.(a) with 25cm dia glass shade complete.

Supplying and fitting of ceiling fan AC operated type 220/250 volt. Complete with 3Nos of blades down rod canopy hanging shackle & regulator complete with 30mm length down rod supplied with the fan by the dealer but the extra length will be charged @ Rs25.00/ mtr

AC ceiling Fan '1400' mm sweeps

Medium Point wiring up to 6 mts (i)With copper conductor

Supplying , installation testing & commissioning of self contained emergency light unit 1x3 watt double sided for wall / ceilling mounting with suspension / mounting kit, inbuilt standby battery( for 2hours backup)and battery charger etc.

1 x 3 W double sided

Supplying fitting and fixing of exhaust fan double bearing self lubricating type single phase 50Hz 250V AC operated complete with supporting frame, fan blades, nuts and bolts, fan regulator, capacitor, adjustable type lever and other petty accessories as required

Supplying, fixing, connecting, testing and commissioning of calling Bell/ Bell indicator type suitable for 230 V as well as battery operated complete with all necessary accessories

Supplying fitting and fixing Batten LED light fitting complete with all accessories for surface or pendant mounting as per Department direction and approved

Gong Bell

Ding dong Bell

Remote Bell

18 watt Round

10 watt Bulk head

Supplying and laying of 15mm × 5mm GI/Copper Strip at 0.50mts, below ground.

With 25mm×5mm copper strip

with 25mmx6mm GI strip

With 3 ft high road

Medium Duty Exhaust Fan

Supplying fitting & fixing earthing with copper earth plate 600 × 600mm × 6mm thick including accessories & providing masonry enclosure with cover plate having locking arrangement & watering pipe etc with charcoal, salt set complete as required

Supplying fitting & fixing earthing with GI earth plate 600 × 600mm × 6mm thick including accessories & providing masonry enclosure with cover plate having locking arrangement & watering pipe etc with charcoal, salt set complete as required

Providing, fixing, connecting and testing of lightning conductor (AirTermination) made of 32 mm dia GI Pipe 2 meters long with 150X180 mm dia galvanized base plate complete with all necessary accessories

Supplying fitting and fixing of LAN (Computer Cables)

with 25mmx3mm GI strip

Supplying, fitting and fixing of copper/Alluminium lightning Arrestor with 5no.s finger at the top & copper base plate at the bottom complete.

SITC of Dome Camera as per site condition complete with all accessories 4MP

SITC of External light of 70 watt LED fixture with 7 meter GI pole of single arm, including foundation, foundation bolts, nuts, MCB, internal wiring with 3R x 2.5 sqmm, conduiting etc. complete as per site requirement

Supply, Installation,

Testing and Commissioning of following rated high performance IGBT based fully microprocessor controlled (Single phase Input & Single phase Output) online UPS system suitable for input and output parameters as per specifications. The UPS shall have Separate Galvanic Isolation Transformer Inbuilt/External K13 Copper Wound (After Static Switch) transformer. The UPS shall be provided in powder coated fan cooled enclosure painted in colour as per specifications. The UPS shall be suitable for normal, emergency, recharge, by-pass and maintenance mode including bypass arrangement. The UPS shall have a microprocessor based display and control panel. UPS shall have own batteries with 30 minute battery back-up with SMF batteries .Complete system must be provided as per specifications approved drawing and as per site requirement including inter connecting cables from battery to UPS, UPS to panel with single core copper cabling etc. UPS shall work on parallel/ hot redundancy mode, cost of supporting kit shall be included. supports for complete system as approved by the Engineer in charge complete in all respect.

70W suitable for pole dia 76mm

5.5 KVA UPS described as above with 30 minute battery Backup

Part - D: DG Set

CAT - 6 unarmoured UTP

Part-C: UPS

White Vitreous china Orissa pattern W.C, pan of size 580x440 mm with integral type foci rests

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern. including painting of fittings and brackcts, cutting and making good the walls wherever require:

CAT - 6 unarmoured UTP

Part-C: UPS

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610x390x370 mm having pre & post flushing with water (250 ml & 500 ml consumption), hawing water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

CAT - 6 unarmoured UTP

Pange of two urinal basins with 5 litre white p.V.C. automatic flushing cistern

CAT - 6 unarmoured UTP

Part-C: UPS

10 ltr Capacity - white

10 ltr Capacity - coloured

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete:

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

CAT - 6 unarmoured UTP

Black solidnplastic seat with lid

CAT - 6 unarmoured UTP

Part-C: UPS

32 mm dia. And 40mm dia.

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

CAT - 6 unarmoured UTP

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

Rectangular shape 1500x450 mm

Providing and fixing soil, waste and vent pipes:

100 mm diameter

CAT - 6 unarmoured UTP

Part-C: UPS

CAT - 6 unarmoured UTP

Sub Total of Civil Cost: A

CAT - 6 unarmoured UTP

CAT - 6 unarmoured UTP

Part-C: UPS

SANITARY FIXTURES AND FITTINGS

25 mm nominal bore

CAT - 6 unarmoured UTP

Part-C: UPS

40 mm nominal bore

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

CAT - 6 unarmoured UTP

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

Part-C: UPS

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

Providing and fixing ball valve (brass) Of approved quality, High or low pressure, with plastic floats complete:

CAT - 6 unarmoured UTP

Providing and fixing gun metal non-return valve of approved quality (screwed end):

Horizontal

32 mm nominal bore

Neat cement punning

Providing and fixing c.P. brass shower rose with 15 or 20 mm inlet:

Neat cement punning

150 mm diameter

CAT - 6 unarmoured UTP

Providing and fixing brass bib cock of approved quality:

Pr LTR

Providing and fixing C.P. brass bib cock of approved quality conforming to ls:8931 :

Providing and fixing C.P. brass angle valve for basin mixer and geyser points Of approved quality conforming to ls:8931

CAT - 6 unarmoured UTP

Part-C: UPS

m long, weighing not less than 88 gins

DRAINAGE

CAT - 6 unarmoured UTP

Part-C: UPS

180xl50 mm size p type

CAT - 6 unarmoured UTP

Part-C: UPS

455x610 mm rectangular c.I. cover (light duty) the weight of the cover to be not less than 23 kg

500 mm diameter c.I. cover (medium duty) the weight of the cover to be not less than 58 kg

560 mm diameter c.I. cover (heavy duty) the weight of the cover to be not less than 108 kg

Raising manhole cover and frame slab to required level including dismantling existing slab and making good the damage as required (Plaising depth of manhole to be paid separately):

Plectangular manhole 90x80 cm with rectangular cover 600 x 450 mm Of grade

Flectangular manhole 120x90 cm with circular cover 500 mm dia. Of grade MD -10

Flectangular manhole 120x90 cm with circular cover 560 mm dia. of grade HD - 20

WATER HARVESTING

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction Of Engineer-in charge

Supplying, filling, spreading & levelling grovels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads and lifts, all complete as per direction of Engineer-in-charge.

CAT - 6 unarmoured UTP

Part-C: UPS

SANITARY FIXTURES AND FITTINGS

Horizontal

50mm dia Butterfly wall

CAT - 6 unarmoured UTP

50mm dia Non return valve

15 mm nominal bore

Design and Preconstruction Phase

Regulatory Clearances/Permits like Tree Felling Permission and Compensatory Plantation

Lumpsum

Contractors Qualified Environment, Health and Safety Expert/s, PMC's and DSC's Qualified Environmental Experts,PIU and PMU level Qualified Environmental Expert

Baseline Monitoring: Ambient Air Quality

Number

Baseline Monitoring: Ambient Noise quality

Baseline Monitoring: Ground Water quality and Drinking Water

Baseline Monitoring: Surface Water quality

Baseline Monitoring: Soil Quality

Shifting of Utility (if applicable)

Construction Phase (1 Year)

Traffic management at worksite (signage, Warning Lights etc.)

Horticulture and Green Area Development

Waste and wastewater management

Monitoring: Ambient Air Quality

Monitoring: Ambient Noise quality

Monitoring: Ground Water quality and Drinking Water

Monitoring: Surface Water quality

Monitoring: Soil Quality

Rainwater Harvesting structures

Noise Barrier near school and residential areas

Restoration of construction site

Construction Phase (1 Year)

Traffic management at worksite (signage, Warning Lights etc.)

Horticulture and Green Area Development

Water sprinkling during construction

Monitoring: Ambient Air Quality

Operation Phase (1year)

Regulatory Clearances/Permits like Fire NoC, etc.

Waste and wastewater management (including installation and management of Septic tank)

Monitoring: Surface Water quality (depending on availability)

EHS audit Annually

Green area maintenance (Monitoring of Survival of trees) : Annually

Others

Providing and fixing aluminium casement stays, lSl marked, anodized (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

80mm dia Non return valve

Medium Point wiring up to 6 mts (i)With copper conductor

100mm dia Non return valve

Bill of Quantities

BOQ item no

Providing and fixing 75 mm high, 50 mm deep and 18 mm thick stone slab table rubbed, edges rounded and polished, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Earth work in excavation by mechanical means upto a depth of 2 m below the existing ground level for foundation, trenches of foundations, footings of columns/ walls, retaining wall, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification of soils.

All kinds of soil (ordinary soil/ hard soil/ dense soil)

In ordinary rock (soft rock/ medium rock/ hard shale)

In hard rock (soft rock/ medium rock/ hard shale) (Blasting prohibited)

Pr ltr

All kinds of soil

In ordinary rock

In hard rock (Blasting prohibited)

Disposal of surplus earth/ unserviceable material from the work site including loading and unloading complete as directed for a total of 15 km (i.e. 10 km beyond the initial lead of 5 km)

Excavated earth

Excavated rock

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered).

Upto a depth of 1.50 m

Above 1.50 m upto 3.00 m depth

Earthwork in filling (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, including breaking of clods, consolidating each layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

With available excavated earth

Implementation of Emergency Preparedness Plan, Grievance Redress Mechanism, Stakeholder Engagement activities, Traffic Management,etc.

Extra over Item for additional lift of 1.5m or part thereof for all types of soils

Sand filling in plinth in layers not exceeding 150mm in depth including breaking of clods, consolidating by watering and ramming complete as directed (maximum depth 45 cm)

SUB TOTAL

Centering and shuttering including strutting, propping etc. and removal of form for all heights complete and as directed by the Engineer-in-charge.

Shuttering for sides of plain cement concrete work in blinding concrete, plinth protection, copings, sills etc.

Foundations, footings, bases of columns, raft, grade slab etc. for mass concrete (using steel)

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. (using steel)

Suspended floors, roofs, landings, balconies and access platforms, shelves (using steel)

Lintels, beams, plinth beams, girders, bressumers and cantilevers (using steel)

Columns, Pillars, Piers, Abutments, Posts and Struts (using steel)

Stairs/ spiral staircase, (excluding landings) (using timber)

Weather shade, Chajjas, corbels etc., including edges (using timber)

Extra for additional height in centering, shuttering wherever required with adequate bracing, propping etc., including cost of de-shuttering and de-centering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured)

Implementation of Corrective Action Plan

SUB TOTAL

Extra over item No 19.1 above for each subsequent floor or part thereof above the first floor level.

Long point wiring upto 10mts (i) With copper conductor

1 :3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

Providing and laying cement concrete in retaining walls etc. and all works above plinth level such as pilasters, columns, pillars, posts, struts, buttresses, parapets, coping, plain window sills, fillets, sunken floor etc.,, up to first floor level, excluding the cost of centering, shuttering and finishing

Training and Capacity Building

SUB TOTAL

Bill of Quantities for Williamnagar (Hostel Block), East Garo Hills

Providing and laying cement concrete in retaining walls etc. and all works above plinth level such as pilasters, columns, pillars, posts, struts, buttresses, parapets, coping, plain window sills, fillets, sunken floor etc.,, up to first floor level, excluding the cost of centering, shuttering and finishing

1 :2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size)

SUB TOTAL

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per ls: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.

All works up to plinth level

All works above plinth level up to first floor level

Extra for providing richer mixes:

Providing M-30 grade concrete

FIRE EXTINGUISHER

SUB TOTAL

Supplying, fitting and fixing in position reinforcement bars up to lst floor level, conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (Rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc. and no measurement for the same is required)

Thermo-Mechanically Treated bars

ABC Powder Type 5kgs

Providing and fixing parallel threaded couplers conforming to ls code on "Reinforcement Couplers for Mechanical Splices of Bars for Concrete Reinforcement-Specification", to reinforcement bars including threading, enlargement at connection by forging, protecting the prepared reinforcement bars and related operations as required to complete the works as per direction of Engineer in-Charge

Coupler for 16 mm diameter reinforcement bar

Coupler for 20 mm diameter reinforcement bar

Coupler for 25 mm diameter reinforcement bar

SUB TOTAL

Brick work with common burnt clay modular lst class bricks in foundation and in plinth:

In Cement Mortar 1:6 (1 cement : 6 coarse sand)

Brick work in cement mortar with first class brick in superstructure above plinth level up to first floor level in all shapes and sizes:

Cement mortar 1:6 (1 cement : 6 coarse sand)

Co2 Type 4.5kgs

Half brick masonry with common burnt clay (non modular) first class bricks in superstructure above plinth level up to first floor level

Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

SUB TOTAL

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement: 6 coarse sand: 12 graded stone aggregate 20 mm nominal size) up to plinth level with:

Cement mortar 1 :6 (1 cement: 6 coarse sand)

SUB TOTAL

Providing and fixing 18 mm thick gang saw cut, mirror polished, pre-moulded and pre-polished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Sub Total of Sanitary, Plumbing & Fire Fighting Cost: C

Providing edge moulding to 18 mm thick marble stone counters, Vanities, etc.„ including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in Charge.

Granite work

Extra for fixing marble/ granite stone, over and above corresponding basic item, in facia and drops of width up to 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing Of cut edges etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to lS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours and shades of any size as approved by Engineer-in-Charge, in walls, skirting, risers of steps and dados, over 12 mm thick bed Of cement mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Normal range

Providing polished Vitrified wall tiles of approved quality, size, shape and thickness not less than 8 mm on walls and skirting over cement mortar bed 10 mm thick in prop.1:3 (1 cement: 3 coarse sand) including cutting where necessary finished with flush pointing with adhesive or white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed.

Normal range

Tree felling

Granite Stone of approved shade

SUB TOTAL

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought trained and fixed in position with hold fast lugs or with dash fasteners of required diameter & length.

With Teak wood/ Sissu wood.

Providing and fixing ISI marked flush door shutters conforming to lS:2202 (Part I) non-decorative type, core of block board construction with frame of lst class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including lSl marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with wooden battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete:

With Teak wood/ Sissu wood - 50 x 20 mm

Providing and fixing 18 mm thick,150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, lS:3087 marked, including top cover of 6 mm commercial ply wood conforming to lS:303 BWR grade, nickel plated M.S. pipe 20 mm dia (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100x40x40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Extra for using veneered particle board conforming to lS:3097 Grade I, in item of pelmet 18 mm thick 150 mm wide.

Particle board with decorative veneering on both sides

Providing and fixing teak wood lipping of size 25x3 mm in pelmet.

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25 mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete:

25 mm dia

Providing & fixing decorative high pressure laminated sheet of plain/ wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to lS : 2046 Type S, including cost of adhesive of approved quality.

1.5 mm thick

SUB TOTAL

Providing and fixing in position collapsible steel shutters with vertical channels 20xl0x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia. steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer

Grand Total Cost of ITI-Williamnagar (Hostel Block)

Bill of Quantities for ITI-Williamnagar (Academic Block), East Garo Hills

Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered).

Providing and fixing M.S.fan clamp type I or II of 16 mm dia. M.S.bar, bent to shape with hooked ends in RCC slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars, etc. including priming coat with approved steel primer all complete.

Fixed to openings/ wooden frames with rawl plugs screws etc.

Providing and injecting approved grout in proportion recommended by the manufacturer into cracks/ honey-comb area of concrete/ masonry by suitable gun/ pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge

Stirrer mixed Acrylic Polymer of approved make @ 2% of weight of cement used) modified Cement slurry made with non-shrink compound in concrete/ BCC work

Providing and fixing bolts including nuts and washers complete.

SUB TOTAL

Normal range (For toilets)

General Note for Flooring :

All Stone flooring should be adequately protected with plastic sheets, POP layer till final polishing & handing over, without any extra payment.

Providing and laying damp proof course with cement concrete in prop 1 :11/2:3 with graded stone aggregate of 10 mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

40 mm thick

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and groute

d with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing soling with stone, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.

Stone Soling, 150 mm

Filling sunken floor with broken brick bats/ stone aggregates and sand including compacting and supplying of materials complete as specified and directed for all levels.

Same as Items 1.0 above but for each additional 1 m depth or part thereof beyond the initial depth of 2 m

Brick bats

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 :4 (1 cement: 4 coarse sand).

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade Of the slabs, including rubbing and polishing complete

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Size of Tile 600 x 600 mm

Extra over item No 11.2 & 12.0 above for each subsequent floor or part thereof above the first floor level.

Building1

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg Of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling, grouting and finishing complete as per direction of Engineer-in-charge

SUB TOTAL

Providing & fixing G.I. Hexagonal chicken wire mesh of 19 size of aperture (12mm x 20 gauge) confirming to IS : 3150 at the junction of dissimilar surfaces of brick / block masonry wall and RCC column / beams and the like including necessary "U" nails / screws with cleats for fixing, overlapping, necessary scaffolding etc. complete all as per specification and as directed by the Engineer-in-charge for all heights and all locations.

PLASTERING

Providing and applying 15 mm thick cement plaster on rough side of single or half brick wall of mix: in cement mortar 1:6 (1 cement : 6 coarse sand) to interior masonry/ concrete wall surfaces

Diluting and injecting chemical emulsion for pre-constructional anti-termite treatment (excluding the cost of chemical emulsion):

Providing and applying 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement: 6 fine sand).

Providing and applying 6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self-curing mortar of approved make as per the direction of Engineer-in-Charge.

per bag of 50 kg cement

Add for plaster drip course/groove in plastered surface or moulding to R.C.C. projections.

Providing and applying 12 mm of cement plaster finished with a floating coat of neat cement of in cement mortar 1:4 (1 cement : 4 coarse sand) to interior masonry/ concrete wall surfaces

SUB TOTAL

Polyurethane (PU) polishing on woodwork with sprayer including sanding, wood filler complete as directed

Long point wiring upto 10mts (i) With copper conductor

PAINTING, OILING, POLISHING, VARNISHING WORKS

Finishing walls with Acrylic smooth exterior paint of required shade, including scaffolding:

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat Of exterior primer applied @ 2,20 kg/10 sqm)

Wall painting with acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

New work (two coats)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

On steel work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

New work (two or more coats)

Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanized iron/ steel works

SUB TOTAL

HD-20; Circular shape 560 mm internal diameter

M.S. Tube

FENCING, SITE DEVELOPMENT & MISCELLANEOUS WORKS

Providing and laying vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to lS:15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Providing and laying tactile tiles (for vision impaired persons as per standards) of size 300 x 300 x 9.8mm having water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20 mm thick base of cement mortar 1:4 (1 cement: 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 in above ground level and removal of rubbish up to a distance of 50 in outside the periphery of the area cleared.

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 in and lift up to 1.5 m in all kinds of soil

Supplying chemical emulsion in sealed containers including delivery as specified.

With borrowed earth/ stone dust carriage upto 5 km

litre

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/ Rm including drilling and plugging holes etc.:

With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/ Rm including drilling and plugging holes etc.:

Treatment of soil under floors using chemical emulsion @ 1 litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor:

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/ Rm including drilling and plugging holes etc.:

Treatment of masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement: 2 coarse sand) to the full depth of the hole:

Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia. holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing

Rectangular shape of 453 x 357mm

Providing and laying 200 microns thick LDPE sheets (conforming to ASTM-D-4397) to serve as a vapour barrier below the plinth, the sheets having overlaps not less than 100 mm longitudinally and 150 mm transversely. The sheets shall be uniform in width and thickness and free from defects such as pin holes, air bubbles, stains etc. The sheets shall be laid flat prior to concreting on a clean broomed surface. The end of the sheets should butt properly against form work or adjacent concrete as the case may be without gaps. The entire work shall be carried out as per manufacturer's specifications/ guidelines and as directed by the Engineer.

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS:10910, on 12 mm dia. steel bar conforming to IS:1786, having minimum cross section as 23x25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacturer's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) complete as per design.

Supplying and fixing C.I. cover without frame for manholes:

560 mm diam

eter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality

SUB TOTAL

Providing and fixing in position weep holes of 75mm diameter made out of UPVC pipes of (4KSC class) of approved make, quality and length upto 500 mm as specified below, including grouting, making good the surrounding surface, cleaning etc. complete

ALUMINIUM WORK

For fixed portion; using anodized aluminium (anodized transparent or dyed to required shade according to ls:1868, minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door. window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge:

With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Extra for applying additional anodic coating AC 25 instead of AC 15 to aluminium extruded sections.

Providing and placing in position, 100 mm thick factory made machine batched & machine mixed precast RCC rectangular covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia. TMT bars of Fe 500 grade @ maximum 100 mm c/c on both ways, neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick,100 mm wide MS sheet duly painted over priming coat, reinforcement to be welded at edges with MS sheet and providing 2 Nos.12 mm dia. bar for hooks etc. including cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Felling trees of the girth (measured at a height of 1 in above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.

SUB TOTAL

For fixed portion

WATER PROOFING

Note: All the waterproofing treatment shall be executed through a recognized water- proofing agency approved by the Engineer-in-charge. A written guarantee on non-judicial stamp paper shall be submitted by the Contractor for a minimum period of ten years from the certified date of completion for the satisfactory performance of the entire water-proofing system.

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for underground structures as directed by Engineer-in-charge and consisting of :

(i) 1st layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound conforming to lS:2645 in the recommended proportion over the levelling course (levelling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound.

(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions.

(iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 0.008 cum/sqm thoroughly embedded in the 2nd layer.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to ls:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement: 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge:

Providing and placing in position suitable PVC water stops conforming to lS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:

Serrated with central bulb (225 mm wide, 8-11 mm thick)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying:

1st layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours.

2nd layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge over the PCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/ brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1 :5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by the Engineer-in-charge to required slope and treating similarly the adjoining walls up to 300 mm height including rounding of junctions of walls and slabs.

(c) After two days of proper curing, applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1 :4 (1 cement: 4 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm squares, 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.

All above operations to be done in order and as directed and specified by the Engineer-in-Charge.

Providing & mixing approved pure acrylic based polymer modified waterproofing compound in concrete work of approved brand and quality, mixed with cement in required proportions as per manufacturer's guidelines, specifications and as directed by the Engineer-in-Charge. The product shall comply with IS: 9103 and IS: 2645. The product must be free of chlorides and shall comply with ASTM C494 Type A & D.

Note : 1) Reinforced cement concrete shall be paid separately under relevant item

With average thickness of 120 mm and minimum thickness of 65 mm.

Grading roof for water proofing treatment with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

SUB TOTAL

Providing and making khurras 450 x 450 mm with average minimum thickness of 50 mm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

DOOR AND WINDOW FITTINGS

Hinges

Providing and fixing lS:12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:

Providing and fixing oxidized M.S. double acting spring hinges with necessary screws etc. complete.

Providing and fixing stainless steel (SS-304 grade) friction hin

ges to the side/ top hung windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge

Handles

Providing and fixing aluminium handles, lSl marked, anodized (anodic coating not less than grade AC 10 as per lS:1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing bright finished brass 100 mm mortise latch and lock, lsl marked, with six levers and a pair of anodized (anodic coating not less than grade AC 10 as per ls:1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3 mm thick & 2100 mm long with SS screws etc. complete as per direction of Engineer-in-Charge

(b) Laying brick bats with mortar using broken bricks/ brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1 :5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by the Engineer-in-charge to required slope and treating similarly the adjoining walls up to 300 mm height including rounding of junctions of walls and slabs

Anodized (AC 15) aluminium tubular handle bar (for glass door)

Locks & latches

Providing and fixing bright finished brass 100 mm mortise latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete

Providing and fixing 100 mm aluminium baby latch, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.

Providing and fixing aluminium sliding door bolts, lSI marked anodized (anodic coating not less than grade AC 10 as per ls:1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

Extra over item 14.0 above for each subsequent floor or part thereof above first floor level.

Door closers, stoppers & tower bolts

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with lSI, lS:3564, embossed on the body, door weight up to 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Extra over item No 18.1 above for each subsequent floor or part thereof above the first floor level.

Providing and fixing aluminium hanging floor door stopper, lSl marked, anodized (anodic coating not less than grade AC 10 as per ls:1868) transparent or dyed to required colour and shade, with necessary screws etc. complete

Twin rubber stopper

Window fittings

Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete.

Signages (Door mounted)

SUB TOTAL

Providing & fixing brush finished 16 SWG stainless steel stain finished (SS 304 Grade) signages of specified size, approved make and quality at all indicated locations as per approved shop drawings and as directed by the Engineer-in-charge .

Signages of 200 mm x 200mm size and make and mounted on door / wall, fixed with SS screws including all accessories etc. complete.

SUB TOTAL

Wiring to a power plug as in item No.6 above with 2X4mm 2 including supplying of 15Amp 5 in 1 SS combined with continuous earth wire to a power point complete

HORTICULTURE AND LANDSCAPING

Providing and fixing bright finished brass 100 mm mortise latch and lock, lsl marked, with six levers and a pair of anodized (anodic coating not less than grade AC 10 as per ls:1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing Brass 100 mm mortise latch and lock with 6 levers without pair of handles (best make of approved quality) tor aluminium doors including necessary cutting and making good etc. complete

Providing and fixing 100 mm aluminium baby latch, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete

Providing and fixing aluminium sliding door bolts, lSI marked anodized (anodic coating not less than grade AC 10 as per ls:1868), transparent or dyed to required colour or shade,with nuts and screws etc. complete:

Providing & fixing brush finished 16 SWG stainless steel stain finished (SS 304 Grade) signages of specified size, approved make and quality at all indicated locations as per approved shop drawings and as directed by the Engineer-in-charge

Part A: 415V System

Electrical Works:

Providing, laying, connection, testing & commissioning of the following sizes of 1100V grade Copper conductor armoured underground cable & overall PVC sheathed cable as per ISI code in trenches including the cost of digging of trenches, sand cushioning with laying etc. and refilling the same in layers or by supporting them in walls and all other accessories as required.

Granite of any colour and shade, area of slab upto 0.50 sqm

With 3.5 core 50 sqmm

With 4 core 10 sqmm

With 4 core 6 sqmm

With 3 core 10 sqmm

Suspended floors, roofs, landings, beams and balconies (Plan area to be measured) (For total height of 6.60 m (i.e.3.10m over and above the standard height of 3.5 m)

With 3 core 4 sqmm

1:3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) (For cement concrete screed below floors)

Long point wiring upto 10mts (i) With copper conductor

With 4 core 6 sqmm

Medium Point wiring up to 6 mts (i)With copper conductor

Providing Vitrified Anti-skid Tiles of approved quality size, shape not less than 8 mm on floor, skirting over a cement mortar bed 15 mm thick of 1:3 (1 cement: 3 coarse sand) complete at all level as specified and directed.

Part B: Building Electrification

Wiring in looping system with copper PVC cable 250/440 volt grade of size 1.5 sqmm of approved quality using PVC casing capping incluiding 5 amperes switch Indian best quality ceiling rose etc. capable to a highest point

Wiring as in item No.6 above to a Ceiling/ Exhaust Fan Point

Drawing of Main and Sub-main line with DGSD approved VIR or PVC 250/440 Volt grade in PVC casing capping complete with all accessories.

With 2×2.5mm2 Copper Conductor

With 2X4 mm2 Copper Conductor

With 2X6 mm2 Copper Conductor

Drawing 3 phase Main Line 4 wire with DGSD approved VIR PVC cable 660 V grade in casing capping with all necessary accessories

With 4 X 6 sq. mm copper conductor

With 4 X 10 sq. mm copper conductor

Supplying & fixing of Load Kontaket Miniature Circuit Breakers (MCBs)

6 - 32 Amp. SP MCB

40 - 63 Amp. SPN MCB

40 - 63 Amp. TPN MCB

Supplying, fitting & fixing of Load Kontaket Miniature circuit breakers Double Pole (Isolator)

32 Amp DP Isolator

40 Amp DP Isolator

63 Amp DP Isolator

100 Amp DP Isolator

125 Amp DP Isolator

Supplying, fitting and fixing of Residual-current circuit Breaker with Overcurrent protection RCBOs assembled for AC applications upto 63A.

Supplying, fitting and fixing of Moulded case circuit Breaker of the following capacity

4 Poles 16 -63 Amp Capacity

4 Poles 80 -100 Amp Capacity

Supplying, fitting and fixing of SPN / TPN MCB Metal enclosure MCB Distribution box

Supplying, fitting and fixing of SPN / TPN MCB Metal Enclosure Distribution Board

12 Way (8+36) Modules

Supplying, fitting and fixing Metal box of following sizes on surface or in recess with suitable size of Phendie Lamiated sheet cover in the front including painting etc. as required.

75mm x 75mm x 60mm deep

Wiring as in item No.1 complete to a light plug point when fixed on same boad.

Long point wiring upto 10mts (i) With copper conductor

Long point wiring upto 10mts (i) With copper conductor

200mm x 300mm x 100mm deep

Wiring to a power plug as in item No.6 above with 2X4mm 2 including supply

ing & Fitting of 15Amp 5 in 2 SS combined with continuous earth wire to a power point complete

250mm x 300mm x 100mm deep

Supplying fitting and fixing LED fittings of different wattage,surface or recess or pole mounting, direct or indirect luminair square or round shape also suitable for porch lighting etc.fitted with mirror reflect or complete with all neccessary accessories.

Supplying fitting and fixing complete polish brass bracket, 16mm dia and 23cm long with cast backplate and brass lamp holder with LED lamp.(a) with 25cm dia glass shade complete.

Supplying and fitting of ceiling fan AC operated type 220/250 volt. Complete with 3Nos of blades down rod canopy hanging shackle & regulator complete with 30mm length down rod supplied with the fan by the dealer but the extra length will be charged @ Rs25.00/ mtr

AC ceiling Fan '1400' mm sweeps

Medium Point wiring up to 6 mts (i)With copper conductor

Supplying , installation testing & commissioning of self contained emergency light unit 1x3 watt double sided for wall / ceilling mounting with suspension / mounting kit, inbuilt standby battery( for 2hours backup)and battery charger etc.

1 x 3 W double sided

Supplying fitting and fixing of exhaust fan double bearing self lubricating type single phase 50Hz 250V AC operated complete with supporting frame, fan blades, nuts and bolts, fan regulator, capacitor, adjustable type lever and other petty accessories as required

Supplying, fixing, connecting, testing and commissioning of calling Bell/ Bell indicator type suitable for 230 V as well as battery operated complete with all necessary accessories

Supplying fitting and fixing Batten LED light fitting complete with all accessories for surface or pendant mounting as per Department direction and approved

Gong Bell

Ding dong Bell

Remote Bell

18 watt Round

10 watt Bulk head

Supplying and laying of 15mm × 5mm GI/Copper Strip at 0.50mts, below ground.

With 25mm×5mm copper strip

with 25mmx6mm GI strip

With 3 ft high road

Medium Duty Exhaust Fan

Supplying fitting & fixing earthing with copper earth plate 600 × 600mm × 6mm thick including accessories & providing masonry enclosure with cover plate having locking arrangement & watering pipe etc with charcoal, salt set complete as required

Supplying fitting & fixing earthing with GI earth plate 600 × 600mm × 6mm thick including accessories & providing masonry enclosure with cover plate having locking arrangement & watering pipe etc with charcoal, salt set complete as required

GI Earth Plate Electrode

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed togcther at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements tor inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to ls:4454 - part1 and M.S. top cover of required thickness tor rolling shiitters.

Supplying fitting and fixing of LAN (Computer Cables)

with 25mmx3mm GI strip

SITC of External light of 70 watt LED fixture with 7 meter GI pole of single arm, including foundation, foundation bolts, nuts, MCB, internal wiring with 3R x 2.5 sqmm, conduiting etc. complete as per site requirement

Supply, Installation,

Testing and Commissioning of following rated high performance IGBT based fully microprocessor controlled (Single phase Input & Single phase Output) online UPS system suitable for input and output parameters as per specifications. The UPS shall have Separate Galvanic Isolation Transformer Inbuilt/External K13 Copper Wound (After Static Switch) transformer. The UPS shall be provided in powder coated fan cooled enclosure painted in colour as per specifications. The UPS shall be suitable for normal, emergency, recharge, by-pass and maintenance mode including bypass arrangement. The UPS shall have a microprocessor based display and control panel. UPS shall have own batteries with 30 minute battery back-up with SMF batteries .Complete system must be provided as per specifications approved drawing and as per site requirement including inter connecting cables from battery to UPS, UPS to panel with single core copper cabling etc. UPS shall work on parallel/ hot redundancy mode, cost of supporting kit shall be included. supports for complete system as approved by the Engineer in charge complete in all respect.

70W suitable for pole dia 76mm

5.5 KVA UPS described as above with 30 minute battery Backup

Part - D: DG Set

CAT - 6 unarmoured UTP

Part-C: UPS

White Vitreous china Orissa pattern W.C, pan of size 580x440 mm with integral type foci rests

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern. including painting of fittings and brackcts, cutting and making good the walls wherever require:

CAT - 6 unarmoured UTP

Part-C: UPS

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610x390x370 mm having pre & post flushing with water (250 ml & 500 ml consumption), hawing water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

CAT - 6 unarmoured UTP

Pange of two urinal basins with 5 litre white p.V.C. automatic flushing cistern

CAT - 6 unarmoured UTP

Part-C: UPS

10 ltr Capacity - white

10 ltr Capacity - coloured

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete:

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

CAT - 6 unarmoured UTP

Black solidnplastic seat with lid

CAT - 6 unarmoured UTP

Part-C: UPS

32 mm dia. And 40mm dia.

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

CAT - 6 unarmoured UTP

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

Rectangular shape 1500x450 mm

Providing and fixing soil, waste and vent pipes:

100 mm diameter

CAT - 6 unarmoured UTP

Part-C: UPS

CAT - 6 unarmoured UTP

Sub Total of Civil Cost: A

CAT - 6 unarmoured UTP

CAT - 6 unarmoured UTP

Part-C: UPS

SANITARY FIXTURES AND FITTINGS

25 mm nominal bore

CAT - 6 unarmoured UTP

Part-C: UPS

40 mm nominal bore

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

CAT - 6 unarmoured UTP

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

Part-C: UPS

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

Black solidnplastic seat with lid

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan

Providing and fixing ball valve (brass) Of approved quality, High or low pressure, with plastic floats complete:

CAT - 6 unarmoured UTP

Providing and fixing gun metal non-return valve of approved quality (screwed end):

Horizontal

32 mm nominal bore

Neat cement punning

Providing and fixing c.P. brass shower rose with 15 or 20 mm inlet:

Neat cement punning

150 mm diameter

CAT - 6 unarmoured UTP

Providing and fixing brass bib cock of approved quality:

Pr LTR

Providing and fixing C.P. brass bib cock of approved quality conforming to ls:8931 :

Providing and fixing C.P. brass angle valve for basin mixer and geyser points Of approved quality conforming to ls:8931

CAT - 6 unarmoured UTP

Part-C: UPS

m long, weighing not less than 88 gins

DRAINAGE

CAT - 6 unarmoured UTP

Part-C: UPS

180xl50 mm size p type

CAT - 6 unarmoured UTP

Part-C: UPS

455x610 mm rectangular c.I. cover (light duty) the weight of the cover to be not less than 23 kg

500 mm diameter c.I. cover (medium duty) the weight of the cover to be not less than 58 kg

560 mm diameter c.I. cover (heavy duty) the weight of the cover to be not less than 108 kg

Raising manhole cover and frame slab to required level including dismantling existing slab and making good the damage as required (Plaising depth of manhole to be paid separately):

Plectangular manhole 90x80 cm with rectangular cover 600 x 450 mm Of grade

Flectangular manhole 120x90 cm with circular cover 500 mm dia. Of grade MD -10

Flectangular manhole 120x90 cm with circular cover 560 mm dia. of grade HD - 20

WATER HARVESTING

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction Of Engineer-in charge

Supplying, filling, spreading & levelling grovels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads and lifts, all complete as per direction of Engineer-in-charge.

CAT - 6 unarmoured UTP

Part-C: UPS

SANITARY FIXTURES AND FITTINGS

Horizontal

50mm dia Butterfly wall

CAT - 6 unarmoured UTP

50mm dia Non return valve

80xl.25 mm M.S. laths with 1.25 mm thick top cover