PROVN OF TOILET FOR JCOS/ORS NEAR BLDG NO F/2/2, PROVN OF FOUR WHEELER PARKING NEAR NEW PEPTA, PROVN OF RECHARGE PIT NEAR GATE NO 3, PROVN OF HIGH MAST LIGHT IN OPPOSITE TO 19 MD ACCN SITE AND TRG AREA

Amount

Surface dressing n.exc (Not exceeding) 15 cm deep and getting out soft/loose soil complete all as spd and directed.

Excavating in trenches , n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells, cesspits ,manhole pier hole, laying of cables, pipes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in any kind of soil Note : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final, conclusive and binding.

Excavation over area n.exc 1.50m deep and getting out soft/loose soil complete all as spd and directed.

All as per item No 3.00 here-in-above but depth exc 1.50 m but n.exc 3.00 mtr

All as per item No 3.00 here-in-above but depth exc 3.0 m but n.exc 4.50 mtr

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose complete all as specified and directed.

Removing excavated Materials (Soils) not exc. 50.00 mtr and depositing where directed at a level not exc. 1.50 mtr above the Starting Point in Soil, complete all as specified and as directed.

M & L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering and all as specified and directed.

M&L for sand filling under floors or in foundations including watering, ramming and consolidation complete all as specified and directed.

M&L for hand packed gravel (stone chips 12.50mm ) for filling in bore holes and inside of recharge pit complete all as specified and directed.

M&L for broken stone or boulders hard core gauge n.exc 63mm deposited, spred and levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces complete all as specified and directed complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregates) as in bed concrete for foundation filling & mass concrete complete all as specified and directed

M & L for PCC (1:3:6) Type C2 using 40 mm graded aggregate used as in sub base floor/pavings and finishing complete all as specified and as directed.

M&L for cement concrete type C-1 1:3:6 (using 20mm graded stone aggregate) in cills, steps, plinth courses, string courses, lacing courses, parapets, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed rounded or chamfered on edges complete all as specified and directed

M & L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete etc complete all as directed.

M & L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) in columns, pillars, piers, etc complete all as specified and directed

M & L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

M & L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

M & L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) as Chajjas complete all as spd and directed.

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild steel TMT bars 6mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups , spacers and binders, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides of pillars, posts, struts, piers, columns, and stanchions for fair finished surfaces of concrete complete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finished surfaces of concrete complete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for rough finished surface, not exceeding 200m thick (Horizontal or sloping) complete all as specified and directed.

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished flat surface complete all as specified and directed.

M&L for old size brickwork with fly ash bricks straight or curved on plan to any radius built in CM 1:6 complete all as specified and directed.

M&L for old size brickwork with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:6 complete all as specified and directed.

M&L 15 mm thick rendering in cement mortar 1:4 inside and outside wall of manhole,drain,bldgs, of brick work/concrete suface finished fair and even with approved water proofing compound (as per manufacturing instraction), if ordered, complete all as specified and as directed. (Note:- WPC will be measured and paid separately)

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:4) and finish smooth & even with using extra cement complete all as specified and directed.

Supply only liquid Water proofing compound complete all as specified and directed.

M&L for grading roof in cement mortar 1:3, 25mm thick in edge and 50mm thick in ridge including necessary curing complete all as specified in SSR Part I clause No 11.42.2 complete all as specified and directed.

M & L for providing water proofing treatment with a layer of APP based polymeric membrane, 3 mm thick (minimum), weighing not less than 3.60 kg/Sqm reinforced with polymer non woven fabric (weighing not less than 160 gm/ Sqm) shall be applied over one coat of cold bituminious primer @ 0.40 ltr/ Sqm ( membrane shall be laid using butane torch and sealing all joints etc, complete all as specified and directed .( Note: The overlaps shall be of minimum 75 mm on longitudinal direction and 100 mm on transverse direction) complete all as specified and directed.

M&L for preparing surfaces of roof and applying one coat of aluminium Paint complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:6) on other than fair faces of brick work or concrete surfaces, finished fair and even, complete all as specified and directed.

M&L for rendering 5mm thick on fair faces of ceiling / chajja concrete surfaces in cement mortar 1:3 complete all as specified & directed.

S & F solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitabale PVC sheet beading, and jointed together with solvant cement, and S&F in the frame at side as per specification and drawing.

S & F 75 mm size butt hinges extruded aluminium alloy/Stainless steel with galavanised mild steel hing pin anodised and fixed type C-21 complete all as specified and directed.

S&F 150 mm long Aluminium, anodised, barrel tower bolt of extruded section complete all as specified and directed.

S&F aluminium handles, cast type, anodised 150mm long complete all as specified and directed.

Anodised powder coated aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etccomplete all as specified and directed.

Anodised powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.)complete all as specified and directed.

Sheet glass 5.5 mm thick , ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane.

M&L cement concrete type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) 25 mm thick as in levelling of floor for receiving screed bed for floor finishes complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm in floors laid over 15mm thick 1:6 cement mortar screed bed etc. set and jointed in neat cement slurry and pointed in white of coloured cement to match complete all as specified and directed.

M & L Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick cement plaster in CM 1:3 on brick or concrete surfaces complete all as spd and directed.

M&L for 40mm thick rough dressed sand stone flooring, laid dry but jointed and pointed in CM 1:3 complete all as spd and directed.

M&L for cement concrete type C2 1:3:6 (40mm graded aggregate) 75mm thick as in plinth protection finished even and smooth without using extra cement, incl making joints 10mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with and including bitumen and sand 1:3 by weight complete all as specified and directed.

Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer over plastered surfaces of walls to prepare the surface even and smooth complete all as specified.

M&L for prepration of new plastered surfaces and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for preparation new plastered surfaces and applying three coat of white washing on ceiling complete all as specified and directed.

S&F tubular towel rail brass chromium plated 20 mm dia `D' type 60 cm long between flanges complete all as spd and directed.

S&F vitreous china wash down closet pan, pedestal pattern pedestal pan and trap (excluding flushing cistern and flush pipe), connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc and including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel CP or aluminised hinging device complete all as spd and directed.

S&F vitreous China squatting pan, ' Orissa patteren, size 580 x 440 mm white, with integral footrests (excluding flushing cisteren and flush pipe) complete all as specified and directed.

S&F 10 litre capacity PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete (with brackets). Make- Hindware, Parryware, commander (Sim Line) incl flush pipe of plyethene of low or high density of PVC 32mm dia for low level cistern all as specified and directed.

S&F vitreous China wash basin white, flat back,size 550X450 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting for pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as spd and as directed.

S&F for 32mm dia PVC waste pipe complete all as spd and directed

S&F Bib tap long body with CP nipple cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed for iron pipe, suitable for 15 mm bore complete all as specified.

S&F Pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed

S&F for stop valve/angle valve cast copper alloy fancy type chromium plated concealed with long shank type screwed down, high pressure with capstan head suitable for 15 mm bore complete all as specified.

S&F for CP Grating square with hole 150 mm size of PTMT (Minimum weight 100gms) complete all as specified and directed

S&F in Grating square with out hole 150 mm size of PTMT (Minimum weight 100gms) complete all as specified and directed

Supply flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern complete all as specified and directed

S&F PVC connection 15 mm size with PTMT nuts of length 450mm complete all as specified and directed

S & F soap dish, vitreous china white, approximate size 160 x 160 x 90mm complete all as specified and directed

S&F PVC (SWR) floor trap 75mm dia of outlet plain with grating including jointing with solvent cement complete all as specified and directed

S&F PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint , laid in trenches or in floors complete all as specified and directed.

S & F PVC (SWR) bends any radius of 75 mm bore with access door complete all as specified and directed

S&F PVC (SWR) junction single (single T) equal or unequal of 75 mm dia complete all as spd and directed.

S&F for PVC (SWR) vent cowl 75 mm bore complete all as spd and directed.

S&F PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors all as specified and directed .

S&F for PVC SWR bends of 110 mm bore complete all as spd and directed.

S&F for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

Cutting chases, pinning in making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good, cutting n. exc. 10cm girth complete all as spd and directed.

S&F for 16 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F for 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F for Gun metal gate valve,20 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed.

M&L Cement concrete 1:3:6, type C-1(using 20mm graded stone aggregate) in surface channels and drains and Manholes complete all as specified and directed.

M&L for cement concrete type B-2, 1:2:4 (using 40 mm graded stone aggregate) in surface channels and drains for benching complete all as specified and directed

M&L for forming fair finished drains or channels nner girth n.exc 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

M&L for forming fair finish drain channel inner girth exc 30 cm but not exc 50 cm in girth in cement concrete using extra cement complete all as specified and directed

Supplying and laying of PVC underground drainage sewer system pipe bearing 160 mm dia SN 8 including jointing with couplar, bend tee as per site requirement complete laid in trenches or floors complete all as specified and directed.

Material and labour for cement concrete bed to drain pipe for 150mm bore of pipe including forming cradles in Cement concrete 1:3:6 Type C2 complete all as specifiedand and as directed.

M&L for precast cement concrete Type B-1,1:1.5:3 (using 20mm graded crushed stone aggregates) set in cm 1:4 as in mahhole cover etc complete all as spd and as directed.

M&L for machine pressed precast concrete pre-polished interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006 of 80 mm thickness M-40 Grade complete all as specified and directed.

M&L for factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified as directed.

M&L, for preparation of concrete kerb stone or plaster surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of plastic emulsion paint overr one coat of priming paints plaster coat complete all as specified and directed.

Drilling of bore hole by any method, through any kind of soil, boulders, rocks for a bore of 350 mm dia below ground level (upto a depth of 40.00 m or more) including making of initial bore holes and disposal of spoil from the site, complete all as specified and as directed

Supply and lowering and fixed in position 150mm dia nominal size(Internal) PVC screen slotted pipe with Ribs / Ribbed Screen Pipes,8mm wall thickness(Min), of 3 mtr length each pipe including socket and jointing materials,complete all as specified as per IS 12818-2010 and as directed by Engr-in-Charge.

S&F 150mm UPVC pipes (SCH-40) including socket and jointing materials,complete all as specified

S&F 150mm UPVC vent cowl .

E/M Portion M & L for concealed point wiring for fan/light point controlled by one one way switch complete with 1.5 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red/yellow/blue wires for phases and black wire for neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and including PVC FRLSH insulated 1.5 sq mm copper conductor for earth continuity (Green Colour) and connected to common earth dolly including sunken in GI terminal box 2.8 mm thick bakelite hylam sheet cover, ISI marked with CM/L no. for mounting switch & sockets ect. Note :- Cost of PVC conduit, cutting chases of wal/ceilingl, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

Material & Labour for point wiring complete with 4.0 sq mm FRLSH, PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral),drawn into and including PVC casing- caping (double interlock type) of not less than 20mm width with accessories and fittings such as bends, elbows, tees, crosses, junction box etc, fixed on wall/ceiling with GI saddles, GI screws, rawl plugs etc. for one power point controlled by one switch including pressed steel terminal box powder coated of suitable size with 3 mm thick plastic laminated sheet cover of approved make for housing/mounting switches, sockets & regulators etc. and drawing 4.0 sq. mm copper stranded conductor PVC insulated, unsheated cable as earth continuity conductor, connected to common earth and earth dolly , all as specified and directed by Engineer-in-Charge Note :- Cost of PVC casing & capping, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

Supply and fixed switch piano flush type, single pole , 5/6 Amps, one way complete all as specified.Make: anchor,Penta.

Supply and fixed switch socket combination 16 Amps flush type controlled by one switch complete all ass specified.

Supply & fixed ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

S&F in repairs LED 20 Watt tube light fitting intregated type, including LED retrofit tube lamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting complete all as specified & directed. . Note (i) Make of batten and LED tube lamp should be of same make.

S&F in repairs LED 9/10 Watt tube light fitting mirror intregated type, including LED retrofit tube lamp 9/10 W , LED tube light nominal power 9/10 Watt, L LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 115 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 extruded aluminium LED battens life span of minimum 50000 working hours complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting including taking down old unserviceable complete all as specified & directed. Note : Make of batten and LED tube lamp should be of same make.

Supply & fixing LED security light 35/36 watt (Min) 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with BIS approved driver and lamp, Aluminum die cast housing High efficiency long life LED package in integral module with lumen efficacy of 115 lm/W (Min) and viewing angle of 45 degree to ensure better uniformity, electronic LED driver (SMPS based constant current supply) with Output Short-circuit protection, Surge protection & other reliability test as per latest IS. operational voltage of 170 volts to 270 volts, frequency of 50 Hz, protection grade IP 66, IK-08 CRI greater than or equal to 70% , CW available CCT of 5700K/6500K, power factor of minimum 0.95 , life span of minimum 50000 working hours cincluding necessary electrical connections by PVC sheathed copper conductor wire of 3 core x 1.5 Sqmm and necessary fixing arrangement all as specified. Note : (i) The minimum requirement of lumen efficiency, lumen output and power consumption has been specified. However, as per availability, the bidders may opted higher specification with out any extra cost. The quoted rate is deem to be included for that and no extra payment will be made on this account. (ii) The fittings should be marked 'Date of installation" and "Date of Procurement" with marker pen

Supply and fixing heavy duty metalic body exhaust fan with louvers of sweep 300mm,230 volts with blade and suitable size hole complete with ,ISI marked complete all as apecified an dierected by Engr-in-Charge.

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43, Ik09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed .

Supply and fixed MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

Supply and fixed MCB SPN 32 Amps, 'C' curve, 240 Volts,ISI marked and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

Supply and fixed double door refrigerator, electric driven (Single phase) of capacity 301 Ltr frost free double door 2 star rated convertible refrigerator with digital inverter, convertible 5-in-1 display, including stand for suitable mount all as specified and directed by Engr-in-Charge

Supply, Laying, testing and connecting XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with solid aluminium conductor 1100 volt grade of size 2 core 6 sqmm. , laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including Brass Compression Cable Gland, Terminal Lugs,clamps,nut & bolts etc all as specified

Supply, Laying, testing and connecting XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with solid aluminium conductor 1100 volt grade of size 3.5 core 35 sqmm. , laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including Brass Compression Cable Gland, Terminal Lugs,clamps,nut & bolts etc all as specified

M&L Sand Cushioning (dry) in Trenches for protec-tion of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thick -ness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. (NOTE : For the purpose of Payment, Punned thick-ness of Sand Cushioning only shall be Measured and Paid ).

M&L sub class B bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete.

Supply and fixing/laying 40mm bore, steel tubings, galvanised, light grade with all fitting laid across road , in trenches or across PCC drain or along electric pole or floor/wall etc for protection of cable complete all as specified and as directed.

M & L for Boring of horizontal hole under road, pavement, hardstanding by trenchless technology using ultra sound technique and necessary machine with and including GI Pipe light grade of dia 100 with all fittings, for passing of cable complete all as specified. Note : (i) One run of boring of horizontal hole and one run of GI Pipe light grade of dia 100 with all fittings will be measured as one unit length. (ii) All the precaution to be taken by the contractor before drilling the bore. The contractor has to take plan of existing cables any type and pipe line in existing area before drilling the bore. (iii) Any damage to existing cables any type and pipe line in the way of drilling the bore will be repaired and make good by the contractor. No extra cost will be paid on this account. (iv) Contractor has to get the survey of route, length and depth for boring before quoting the rate.

Design ,Supply, erection, testing & commissioning of 16.00 metres high galvanised Raising and Lowering winch lighting Mast system suitable to install 9 Nos lumineries in symmetrical arrangement with all accessories complete all as specified and as directed by Engr-in-Charge including the followings :- a) Mast shaft in three sections, hot dip galvanised and suitable for wind velocity of 50 metre/second, as per IS 875 part 3. b) Head frame 02 Nos welded with each other with mild steel strip of size 40 x 6mm (01 No suitable for fixing of 09 Nos flood lights and 01 No. suitable for fixing lightning arrestor , aviation light and signal antenna making arrangement with 50 x 50x 5 mm angle iron of length 1.0 metre for each antenna and aviation light and 1.5 metre length of same size for fixing lightning arrestor, steel wire rope of minimum 6 mm dia, double drum winch with mounting arms, three-six LM-6 pulley assembly. c) Galvanised lantern carriage arrangement suitable for motorised antenna having two point suspension system and lightnining finial. d) Integral power tool installed inside base compertment for its operation (CONTD....)

e) Foundation bolts, manufactured from special steel along with nuts, washers, anchor plates and templates. f) Design, supply and casting of suitable RCC foundation with M-25 concrete for the High Mast considering safe soil bearing capacity as 8-10 Tonne/Sq mtr at 2 metre depth. g) 01 No LED aviation obstruction light(for each Mast) including all accessories and necessary electrical connections with suitable size cable. h) 12 core 4 sqmm copper cable for connection between MCB box at base compartmant to junction box at head. j) 3 core 2.5sqmm copper cable for luminaries connection from junction box . k) 2 Nos GI pipe earthing station for each High Mast m) 3 core 2.5sqmm copper cable for connection from feeder pillar box to winch motor. Note:- The quoted rate is deemed to be inclusive of above provisions as listed in Srl No 1114.00 and 114.1 including earth work, foundation complete and no extra payment will be made for completion of the job.

Supply and fixing LED floodlight made up of pressure die cast aluminium housing with toughened glass and high power LEDs and secondary lenses with IP66 protection.with and including 10KV SPD lumen Efficacy ≥ 110 power factor of minimum 0.95 , life span of minimum 50000 working hours and necessary fixing arrangement all as specified. Note : (i) The minimum requirement of lumen efficiency, lumen output and power consumption has been specified. However, as per availability, the bidders may opted higher specification with out any extra cost. The quoted rate is deem to be included for that and no extra payment will be made on this account. (ii) The fittings should be marked 'Date of installation" and "Date of Procurement" with marker pen

Material and labour for earthing complete with Galvanised steel earth plate electrode 600x600x6 mm mm buried directly in ground (Earth pit not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI wire 4 mm as earth lead by means of bolt, nuts, check nuts and washers of galvanised iron or steel, upto 7.5m length, earth strip protected by and including 15 mm dia GI pipe (light grade) and connected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC (1:3:6) type C1 , Precast RCC (1:2:4) Type B1 cover slab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI Pipe (Medium Grade) for watering, Charcoal and salt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any type of soil and disposal of spoil to a distance n.exc 50 m and necessary testing complete all as shown in Electrical Plate No 3 of SSR Part-I. NOTE : 1. The unit rare includes for protectionh GI pipe of 40mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI wire of 32x6mm including protection pipe, from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI strip and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate

M&L for earthing complete with galvanised steel earth plate electrode size 600 x 600 x 6 mm thick, burried directly in ground, (Earth pit not less than 3.25 m deep below ground level) with top edge of the plate not less than 2.5 m below ground level connected to galvanised iron strip 32 x 6 mm as earthin lead wire by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point all as specified or indicated including testing on completion, surrounded from all sides by mixture of charcoal and common salt and electrode by means of steel and GI pipe light grade 20mm dia bore for watering funnel with wire mesh. CI cover with frame, PCC chamber pit with PCC 1:3:6 type C-2 excavation and earth work all as shown in electrical plate No 3 connected to earthing test point all as specified NOTES 1. The unit rate includes for protection pipe and GI strip dia from top of earth plate upto 7.5 meter above ground level. NOTE:- 1. The unit rate includes for protection GI pipe of 40 mm and watering pipe of 20 mm bore including excavation for earth pit in any type of soil/ disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to achieve desired result as the soil resistiviy is very high. 3.The cost of GI strip of size 32 x 6 mm from top of earth plate upto 7.5 meter above ground level is deemed to be included in the unit rate of above item.and copper strip beyond 7.5 RM will be measured seperately. 4. All the joints in GI strip and connection with Earth Plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5. Cost of welding and nut bolts are deemed to be included in the unit rate.

S & F rotational moulded polyethylene ISI marked (vertical cylindrical with close top) as per IS 12701: 1996 of 1000 litres capacity hoisted and fixed in position with and including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 25mm bore dia iron pipe, provision of 25 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including dismantling the existing one and removing to store complete all as specified and as directed.

Supply & fix in 25mm bore GI tubing medium grade in trenches / Floor / pillar connetion in new postion including fittings all as specified & as directed including taking down old unseviceable pipe (Make: Bansal, Jindal)

Supply and fix 25 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

M&L cutting existing steel tubing for alteration or addition of size 40 to 50mm dia GI pipe complete all as directed by EIC.

BHARAT CONSTRUCTION (BID ID -3400152)

Elite Enterprises (BID ID -3386765)