REPAIR AND MAINT OF UG CABLES, ACSR CONDUCTOR, POLES, SECURITY / PERIMETER LIGHTS, LT DISTRIBUTION SYSTEM, LT PANELS, FEEDER PILLARS AND OTHER CONNECTED WORKS AT DAMANA UNDER GE JAMMU

Amount

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth and getting out in soft / loose soil or hard / dense soil for taking up or laying of cable complete all as specified and as directed.

Description same as per Ser Item No 1.00 here-in-before but exceeding 1.5 metre deep but not exceeding 3.0 metre deep complete all as specified and as directed by Engineer-in-Charge.

Supply and laying dry river sand laid in trenches as cable cushioning and covering all as directed. Sand cushioning to under ground electric cable 8cm before laying and 15cm after laying the cable in trenches complete all as specified and as directed by Engineer-in-Charge.

Material and labour well burnt old size sub class ‘B’ bricks, laid flat, in trenches for cable protection complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) mechanically crushed stone for mass filling in pole, pit and foundation etc including provision of necessary form work to achieve fair finished surfaces complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in pole, foundation, stay pits etc including provision of necessary form work to achieve fair finishes surfaces complete all as specified and as directed.

Material and labour for PCC (1:2:4) type C-2 (using 40 mm graded crushed stone aggregate) as in pole, foundation, coping, stay pits etc including provision of necessary form work to achieve fair finishes surfaces complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick layers complete all as specified and as directed by Engineer-in-Charge.

Removal of excavated material not exceeding 50 metre away and depositing where directed at a level not exceeding 1.5 metre above from starting point complete all as specified and as directed by Engineer-in-Charge.

Dismantling and removing and setting aside PCC pole / struts any type by breaking PCC foundation after disconnecting electrical connection including site clearance complete all as specified and directed by Engineer-in-Charge.

Supply, erection of PCC pole 9.0 metre long in true vertical position 102 x 172 mm at top 102 x 279 mm at bottom Class-10 including providing black and white strips with synthetic enamel paint 30 cm each alternate upto 1.5 metre above the coping of pole starting with black strip complete all as specified and as directed by Engineer-in-Charge. Note: - (i) Earth work and PCC shall be measured and paid separately. (ii) Description as per direction of Engineer-in-Charge will be printed on each pole without any extra cost.

Material and labour for steel swagged poles complete poles 9 metre long complete with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP-31 with one coat of red oxide primer and two coats of aluminium paint and including marking alternate 5 no's black and white strip 30 cm height with two coats of synthetic paint over a coat of primer including preparation of new surfaces complete all as specified and as directed at site.

Supply and fixing in replacement indoor / outdoor end termination joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 / 4.0 x 10-50 Sqmm complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement indoor / outdoor end termination joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 x 70-150 Sqmm complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement indoor / outdoor end termination joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 x 185-300 Sqmm complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement indoor / outdoor end termination joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 x 400 Sqmm complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement straight through joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 / 4 x 25-50 Sqmm complete all as specified and as directed by Engineer-in-Charge. Note: - Earth work will be measured and paid separately.

Supply and fixing in replacement straight through joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 x 70-150 Sqmm complete all as specified and as directed by Engineer-in-Charge. Note: - Earth work will be measured and paid separately.

Supply and fixing in replacement straight through joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 x 185-400 Sqmm complete all as specified and as directed by Engineer-in-Charge. Note: - Earth work will be measured and paid separately.

Disconnecting and taking out defective underground cable any size and any type from trenches, roof, pole, pipe, floor, wall etc complete all as specified and as directed.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 16 Sqmm 4.0 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 25 Sqmm 3.5 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 35 Sqmm 3.5 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 50 Sqmm 3.5 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 95 Sqmm 3.5 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 120 Sqmm 3.5 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 150 Sqmm 3.5 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 185 Sqmm 3.5 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 300 Sqmm 3.5 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 400 Sqmm 3.5 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 10 Sqmm 2 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 16 Sqmm 2 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Material and labour for drilling hole of any size manually as per site requirement, drilling for laying pipes under the road, footpaths, PCC ways, boundary wall for crossing electrical cables complete all as specfied and as per directions of Engineer-in-Charge. Note: - Pipe will be measured and paid for separately.

Repair / maint of existing burnt defective UG XLPE cable 1100 Volt grade cable of any size complete with charges for tracing out the fault, cutting / repair and jointing complete with using insulation tape, aluminium thimble, lugs, fitment of jointing kit, thimbles, necessary earth work complete all as specified and as directed. Note: - Aluminium thimble, lugs, jointing kit, thimbles, earth work shall be measured and paid separately.

Supply and fixing stay assembly complete with all accessories, such as stay plate 230 X 230 X 6 mm³, stay rod 215 cm long and 16 mm dia with nuts including GI bow turn buckle, GI stay wire, Loop type insulator etc. all as per electrical plate No 1 or SSR Part - I complete all as specified and as directed including taking down old unserviceable. Note: - Only excavation and PCC work will be measured and paid separately.

Material and labour in replacement including dismantling and taking down old for cross arms, bracings, supports, clamps and back plates fabricated from structural steel section including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and as directed.

Material and labour in replacement for shackle type porcelain vitreous white or brown insulator including GI straps, washers, insulator bolts and nuts for working pressure 1100 Volts, 75 mm height, 90 mm dia, section of strap 30mm x 3mm and dia of bolt 12 mm complete all as specified and as directed by Engineer-in-Charge.

Material and labour in replacement for pin type insulator porcelain vitreous white or brown 1100 Volts grade 100 mm height and 65 mm dia with GI spindle, two GI washer and one GI nut complete all as specified and as directed by Engineer-in-Charge.

Dismantling and taking down old unserviceable ACSR conductor including cutting, welding complete all as specified and as per directions of Engineer-in-Charge.

Material and labour for aluminium conductor steel reinforced (ACSR) including fixing, stretching on poles and proper noseling with binding wire with insulator of any size as required at site complete all as specified and as directed by Engineer-in-Charge.

Material and labour in replacement for 1100 Volts grade heavy duty cable PVC insulated solid aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4 mm GI suspension wire, one twin core cable flat or circular of size 10 Sqmm 2 core complete all as specified and as directed by Engineer-in Charge.

Material and labour in replacement for 1100 Volts grade heavy duty cable PVC insulated solid aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4 mm GI suspension wire, one twin core cable flat or circular of size 6 Sqmm 2 core complete all as specified and as directed by Engineer-in Charge.

Material and labour in replacement for 1100 Volts grade heavy duty cable PVC insulated solid aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4 mm GI suspension wire, one twin core cable flat or circular of size 4 Sqmm 2 core complete all as specified and as directed by Engineer-in Charge.

Dismantling and taking down old unserviceable earthing and material and labour for earthing complete with galvanized steel earth electrode plate of size 60 x 60 x 6mm thick buried directly in ground / earth pit not less than 2.25 metre deep below normal ground level and top edge of earth electrode not less than 1.5 metre below normal ground level and connected with GI earth strip of size 25 x 4mm by means of nut, bolts, washers etc to equipment / machinery all as shown in electric plate No 3 of SSR Part - I including PCC (1:3:6) pit, pit cover 50mm thick, RCC 1:2:4 type B-1 using 8mm tor steel bars @10cm centre to centre both ways, 40mm bore medium grade GI protection pipe, watering pipe 20mm bore medium grade, funnel, wire mesh, also including earth work, common salt, charcoal dust complete all as specified and as directed by Engineer-in-Charge.

Dismantling and taking down old unserviceable earthing and material and labour for earthing complete with galvanized steel earth electrode plate of size 60 x 60 x 6mm thick buried directly in ground / earth pit not less than 2.25 metre deep below normal ground level and top edge of earth electrode not less than 1.5 metre below normal ground level and connected with GI earth wire of size 4 mm by means of nut, bolts, washers etc to equipment / machinery all as shown in electric plate No 3 of SSR Part - I including PCC (1:3:6) pit, pit cover 50mm thick, RCC 1:2:4 type B-1 using 8mm tor steel bars @10cm centre to centre both ways, 20 mm bore medium grade GI protection pipe, watering pipe 20mm bore medium grade, funnel, wire mesh, also including earth work, common salt, charcoal dust complete all as specified and as directed by Engineer-in-Charge.

Material and labour for fixing in replacement GI tubing 50 mm bore light grade, on poles, on walls, under floors, road crossing, as required at site complete all as specified and as directed by Engineer-in- Charge. Note: - Clamps, Nut bolts, saddle etc will be measured and paid separately.

Material and labour for fixing in replacement GI tubing 80 mm bore light grade, on poles, on walls, under floors, road crossing, as required at site complete all as specified and as directed by Engineer-in- Charge. Note: - Clamps, Nut bolts, saddle etc will be measured and paid separately.

Supply and fixing in replacement MCCB TPN 400 Amps, 415 Volts, 50 KA, 4 POLE, Ics=100% Icu, overload adjustable short circuit adjustable type including complete connection all as specified and as per directions of Engineer-in-Charge.

Supply and fixing in replacement MCCB TPN 250 Amps, 415 Volts, 40 KA, 4 POLE, Ics=100% Icu, overload adjustable short circuit adjustable type including complete connection all as specified and as per directions of Engineer-in-Charge.

Supply and fixing in replacement MCCB TPN 200 Amps, 415 Volts, 25 KA, 4 POLE, Ics=100% Icu, overload adjustable short circuit adjustable type including complete connection all as specified and as per directions of Engineer-in-Charge.

Supply and fixing in replacement MCCB TPN 160 Amps, 415 Volts, 25 KA, 4 POLE, Ics=100% Icu, overload adjustable short circuit fixed type including complete connection all as specified and as per directions of Engineer-in-Charge.

Supply and fixing in replacement MCCB TPN 100 Amps, 415 Volts, 16 to 25 KA, 4 POLE, Ics=100% Icu, overload adjustable short circuit fixed type including complete connection all as specified and as per directions of Engineer-in-Charge.

Material and labour for detecting of fault in cable of any type with fault locator equipment which is capable to detect the fault as per cable size / ratings and make the cable serviceable with proper cable joints complete all as specified and as directed. Note: - (a) The fault which is detected through cable fault locater will only be paid under this item. (b) Charges of cable fault locator and DG set including transportation charges deemed to be included in the quoted rate. (c) Earth fault locator will be provided by the contractor for even single fault and no delay on this account will be acceptable otherwise penality will levied Rs 500/- per day. (d) Necessary testing of cable after making joint will be deemed to be including in the cost of relevent item. However necessary earth work cable, cutting, making Joint will be paid under relevant item.

Supply and fixing in replacement of PVC fibre separator for LT line 1100 Volt overhead conductor 3 wire system for maintaining horizontal / vertical spacing of conductor complete with nut and bolt in a span complete all as specified and as directed.

Supply and fixing in replacement of PVC fibre separator for LT line 1100 Volt overhead conductor 4 wire system for maintaining horizontal / vertical spacing of conductor complete with nut and bolt in a span complete all as specified and directed.

Supply and fixing in replacement of PVC fibre separator for LT line 1100 Volt overhead conductor 5 wire system for maintaining horizontal / vertical spacing of conductor complete with nut and bolt in a span complete all as specified and directed.

Labour for cutting of tree branches 2 metre vicinity of the conductor which are touching to the 11/9 metre overhead lines in vertically and horizontally conductor and poles etc, complete clear in a standard span in between two poles as per SSR Part-I, 19.59 and removing cutting material not exceeding 50 metre and depositing where directed at a distance level not exceeding 3 metre from starting point all as specified and as directed. Note: - Pole to pole will be considered as one span of any length and no's of conductor.

Re-stretching existing / retrieved ACSR conductor on LT pole and binding conductor on insulator properly using new binding wire / jumper wire complete all as specified and as directed at site by Engineer-in-Charge. Measurement should be taken in RM on span of 2, 3, 4 and 5 line of overhead conductor. Note: - (i) Replacement of old to new overhead conductor shall be measured and paid for separately.

Material and labour for fixing aluminium terminals (thimbles) in 1100 Volt LT XLPE cable upto size 50 Sqmm including dismantling old thimbles of any type complete all as specified and as directed.

Material and labour for fixing aluminium terminals (thimbles) in 1100 Volt LT XLPE cable upto size 70-185 Sqmm including dismantling old thimbles of any type complete all as specified and as directed.

Material and labour for fixing aluminium terminals (thimbles) in 1100 Volt LT XLPE cable upto size 240-400 Sqmm including dismantling old thimbles of any type complete all as specified and as directed.

Material and labour for shifting heavy items / excavating / cleaning areas / clearing site by providing crane / hydra / excavators / tractors / trolley etc as required at site complete all as specified and as directed.

Supply and fixing in replacement unserviceable indicators LED set of three, RYB as per existing size and sample complete all as specified and as directed by Engineer-in-Charge.

Material and labour for painting, cleaning and repair of LT panel size upto 0.6 X 0.6 X 0.6 metre after cleaning of surface including removing rusted particles, removing dust, tightening nut, bolts, welding and painting on complete panel with two coats of synthetic enamel aluminium paint over a coat of red oxide primer including stand complete all as specified and as directed. Notes: - (i) Cost of marking description on the front door as per directions of Engineer-in-Charge is included in quoted rate. (ii) Cost of misc items like copper cable, lugs, thimbles etc if required are included in quoted rates.

Material and labour for painting, cleaning and repair of LT panel size upto 1.2 X 1.2 X 0.6 metre after cleaning of surface including removing rusted particles, removing dust, tightening nut, bolts, welding and painting on complete panel with two coats of synthetic enamel aluminium paint over a coat of red oxide primer including stand complete all as specified and as directed. Notes: - (i) Cost of marking description on the front door as per directions of Engineer-in-Charge is included in quoted rate. (ii) Cost of misc items like copper cable, lugs, thimbles etc if required are included in quoted rates.

Material and labour for replacement of old unserviceable / broken shutter of LT panel with 3 mm thick CRCA sheet as per existing size to match with the existing panel duly powder coated and welding hinges and fixing complete all as specified and as directed by Engineer-in-Charge.

Material and labour for surface cleaning of steel tubular poles LT 9 metres long including removing rusted particles and painting with two coats of synthetic enamel aluminium paint including cross arms, bracing, supports, clamps, eye hooks, security light bracket, clamp etc and providing black and white strips alternatively 30cm each from coping upto 1.5 metre height starting with black strip using synthetic enamel paints including repairing and painting on coping with cement based white paint complete all as specified and as directed. Notes: - (i) The quoted rates shall include marking of numbers on each LT pole as per directions of Engineer-in-Charge. (ii) The quoted rates shall include the repairing of coping with cement / PCC.

Material and labour for cement based white / off white paint for PCC pole 9 metre long, top to bottom and above 1.5 metre from ground level including black and white strips alternatively 30cm each from coping upto 1.5 metre height starting with black strip using synthetic enamel paint including cross arms, bracing, supports, clamps, eye hooks, security light bracket, clamp etc including repairing and painting on coping with cement based white paint complete all as specified and as directed. Notes: - (i) The quoted rates shall include marking of numbers on each LT pole as per directions of Engineer-in-Charge. (ii) The quoted rates shall include the repairing of coping with cement / PCC.

Material and labour for preparation of old painted / rusted surfaces of steel tubular two pole structure 11 / 9 metres long type 410 SP-31, 55 and applying one coat of synthetic enamel paint upto 1.2 metre height in black and white strip of width 30cm each as per existing pattern above the PCC coping and two coats of aluminum paint (1st quality) beyond 1.2 metre height (for the rest of portion) including cross arms and channel, angle fitted on the pole including writing pole numbers and cutting vegetation growth all around and on the poles upto 1 metre radius complete all as specified and as directed.

Material and labour for preparation of old painted / rusted surfaces of steel tubular four pole structure 11 / 9 metres long type 410 SP-31, 55 and applying one coat of synthetic enamel paint upto 1.2 metre height in black and white strip of width 30cm each as per existing pattern above the PCC coping and two coats of aluminum paint (1st quality) beyond 1.2 metre height (for the rest of portion) including cross arms and channel, angle fitted on the pole including writing pole numbers and cutting vegetation growth all around and on the poles upto 1 metre radius complete all as specified and as directed.

Supply and fixing in repair onload change over switch with sheet steel enclosure 415 V, 4 pole, 100 Amps capacity fixed on walls for electric supply distribution between main and DG set including necessary connection of cables from LT panels to change over switches complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair onload change over switch with sheet steel enclosure 415 V, 4 pole, 200 Amps capacity fixed on walls for electric supply distribution between main and DG set including necessary connection of cables from LT panels to change over switches complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair onload change over switch with sheet steel enclosure 415 V, 4 pole, 315 Amps capacity fixed on walls for electric supply distribution between main and DG set including necessary connection of cables from LT panels to change over switches complete all as specified and as directed by Engineer-in-Charge.

Disconnecting and taking out defective underground cable from trenches, pole, pipe, floor, wall etc and locate the fault, rectify the defect and relaying the XLPE cable underground PVC insulated and overall sheathed aluminium conductor heavy duty 1100 Volts including connecting and testing for any size complete all as specified and as directed by Engineer-in-Charge. Note: - (Excavation / Earth work and sand cushioning, bricks and joint shall be measured and paid for separately.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 10 Sqmm 4 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 25 Sqmm 4 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Material and labour in replacement of PVC insulated and sheathed cable of size 1.5 Sqmm 3 core copper conductor multistranded 1100 Volt grade 230 Volts running through PVC conduit of dia 20 mm with strip clamping on poles at 3 places complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair onload change over switch with sheet steel enclosure 415 V, 4 pole, 63 Amps capacity fixed on walls for electric supply distribution between main and DG set including necessary connection of cables from LT panels to change over switches complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing and fabrication street light bracket made out of GI tubing suitable for 45 / 60 / 90 watt LED light grade upto 1.2 metre length, bend to shape suitable for security light fitting with necessary MS clamps with one coat of red oxide primer and two coats of aluminium paint including nut, bolt, washers etc and including taking out unserviceable bracket and removing from site of work complete all as specified and as directed.

Labour for repair / maint to old / unserviceable LED security / street / flood light of any capacity including taking down existing fitting from pole / building for repair of driver, cable terminal block and connection wire and refixing the same in position after repair including testing complete all as specified and as directed by Engineer-in-Charge. Note: - Spares shall be measured and paid separately under respective item.

Taking down unserviceable street / security light fitting of any type from the pole / building after disconnecting electric connection carefully for replacement of drivers complete all as specified and as directed. Note: - Repair / replacement of spares shall be measured separately.

Supply and fixing in replacement of electronic driver of capacity 45 watt of existing make for LED street light fitting complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement of electronic driver of capacity 60 watt of existing make for LED street light fitting complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement of electronic driver of capacity 90 watt of existing make for LED street light fitting complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement of electronic driver of capacity 120 watt of existing make for LED street light fitting complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement of electronic driver of capacity 200 watt of existing make for LED flood light fitting complete all as specified and as directed by Engineer-in-Charge.

Dismantling and taking down old unserviceable street / security lights and material and labour for new LED street light fittings of 30 Watt, suitable for upto 50 mm OD holder fixed on existing pole, system wattage and high pressure die cast aluminium housing with sealed toughened glass cover, silicon gasket for IP-66 protection suitable for pole mounting SMD LED array with lense, cool white 6500 K, LED efficacy >120 lm/W and system efficacy 110 lm/W, 240 Volts AC, 50 Hz, CRI>70% operating voltage range 160 V-270 V, Power factor > 0.95, working temperature range -20ºC to 60ºC, built in surge protection more than 10 KV with facility of power supply shall be removed without removing light fitting from pole including making proper connection complete including cutting, welding, drilling holes, nut, bolts, washer complete all as specified and as directed by Engineer-in-Charge.

Dismantling and taking down old unserviceable street / security lights and material and labour for new LED street light fittings of 45 watt, suitable for upto 50 mm OD holder fixed on existing pole, system wattage and high pressure die cast aluminium housing with sealed toughened glass cover, silicon gasket for IP-66 protection suitable for pole mounting SMD LED array with lense, cool white 6500 K, LED efficacy >120 lm/W and system efficacy 110 lm/W, 240 Volts AC, 50 Hz, CRI>70% operating voltage range 160 V-270 V, Power factor > 0.95, working temperature range -20ºC to 60ºC, built in surge protection more than 10 KV with facility of power supply shall be removed without removing light fitting from pole including making proper connection complete including cutting, welding, drilling holes, nut, bolts, washer complete all as specified and as directed by Engineer-in-Charge.

Dismantling and taking down old unserviceable street / security lights and material and labour for new LED street light fittings of 60 watt, suitable for upto 50 mm OD holder fixed on existing pole, system wattage and high pressure die cast aluminium housing with sealed toughened glass cover, silicon gasket for IP-66, TOP opening separate driver compartment with frame, suitable for pole mounting SMD LED array with lense, cool white 6500 K, LED efficacy >120 lm/W and system efficacy 110 lm/W, 240 Volts AC, 50 Hz, CRI > 70% operating voltage range 160 V-270 V, Power factor > 0.95, working temperature range -20ºC to 60ºC, built in surge protection more than 10 KV with facility of power supply shall be removed without removing light fitting from pole including make proper connection complete including cutting, welding, drilling holes, nut, bolts, washer complete all as specified and as directed by Engineer-in-Charge.

Dismantling and taking down old unserviceable street / security lights and material and labour for new LED street light fittings of 90 watt, suitable for upto 50 mm OD holder fixed on existing pole, system wattage and high pressure die cast aluminium housing with sealed toughened glass cover, silicon gasket for IP-66, TOP opening separate driver compartment with frame, suitable for pole mounting SMD LED array with lense, cool white 6500 K, LED efficacy >120 lm/W and system efficacy 110 lm/W, 240 Volts AC, 50 Hz, CRI >70% operating voltage range 160 V-270 V, Power factor > 0.95, working temperature range -20ºC to 60ºC, built in surge protection more than 10 KV with facility of power supply shall be removed without removing light fitting from pole including making proper connection complete including cutting, welding, drilling holes, nut, bolts, washer complete all as specified and as directed by Engineer-in-Charge.

Dismantling and taking down old unserviceable street / security lights and material and labour for new LED street light fittings of 120 watt, suitable for upto 50 mm OD holder fixed on existing pole, system wattage and high pressure die cast aluminium housing with sealed toughened glass cover, silicon gasket for IP-66, TOP opening separate driver compartment with frame suitable for pole mounting SMD LED array with lense, cool white 6500 K, LED efficacy >120 lm/W and system efficacy 110 lm/W, 240 Volts AC, 50 Hz, CRI >70% operating voltage range 160 V-270 V, Power factor > 0.95, working temperature range -20ºC to 60ºC, built in surge protection more than 10 KV with facility of power supply shall be removed without removing light fitting from pole including making proper connection complete including cutting, welding, drilling holes, nut, bolts, washer complete all as specified and as directed by Engineer-in-Charge.

Dismantling and taking down old unserviceable street / security lights and material and labour for new LED flood light fittings of 120 watt, system wattage and high pressure die cast aluminium housing with sealed toughened glass cover, silicon gasket for IP-66 protection suitable for pole mounting SMD LED array with lense, cool white 6500 K, LED efficacy >120 lm/W and system efficacy 90 lm/W, 240 Volts AC, 50 Hz, CRI >70% operating voltage range 160 V-270 V, Power factor > 0.95, working temperature range -20ºC to 60ºC, built in surge protection more than 10 KV with facility of power supply shall be removed without removing light fitting from pole including making proper connection complete including cutting, welding, drilling holes, nut, bolts, washer complete all as specified and as directed by Engineer-in-Charge.

Dismantling and taking down old unserviceable street / security lights and material and labour for new LED flood light fittings of 200 watt system wattage and high pressure die cast aluminium housing with sealed toughened glass cover, silicon gasket for IP-66 protection suitable for pole mounting SMD LED array with lense, cool white 6500 K, LED efficacy >120 lm/W and system efficacy 90 lm/W, 240 Volts AC, 50 Hz, CRI >70% operating voltage range 160 V-270 V, Power factor > 0.95, working temperature range -20ºC to 60ºC, built in surge protection more than 10 KV with facility of power supply shall be removed without removing light fitting from pole including making proper connection complete including cutting, welding, drilling holes, nut, bolts, washer complete all as specified and as directed by Engineer-in-Charge.

Taking down old unserviceable timer switches and supply and fixing of Automatic street light control with infrared sensor based NATURE SWITCH and VOLTAGE MONITORING SYSTEM (VMS) single phase load of 8 KW for automation of street lights. Nature switch operation should be based on natural light Lux level required illuminance level for switching ON is < 30 Lux and for switching OFF > 30 Lux. The sensor should also have part night operation facility of minmum 4 hours to maximum 12 hours. VMS should have adjustable over and under voltage trip level and protection against phase loss, neutral loss and phase reverse including power contactors (1 no of capacity 63 Amps per phase each) and incoming (1 no of capacity 63 Amps each) - outgoing MCB (1 no of capacity 63 Amps each) and main load circuit wiring (copper) of minimum 16 Sqmm. The sensor, VMS, Power contactor, MCB's including connected items should be enclosed in a Pole / wall mountable enclosure made of rust proof, electric shock proof, termite proof and FR grade SMC junction box conforming to IP-54 complete all as specified and as directed.

Supply and fixing SMC pole mounted box of size 10" x 8" x 4" with hinged door including clamp, nuts, bolts and washers complete all as specified and as directed and including taking down of old unserviceable junction boxes. The Box includes: - (a) MCB SP 10 Amp, 10 kA 'C' series mounted on din rail - 1 No. (b) Connector block suitable for 3 ph, 4 wire minimum 16 Sqmm cable - 1 No

Material and labour for replacement of old unserviceable switch fuse unit / MCB of any type / capacity with new MCB FP 40 Amps 415 AC, 50 Hz, 25 KA with sheet metal enclosure complete all as specified and as directed.

Material and labour for replacement of old unserviceable switch fuse unit / MCCB of any type / capacity with new MCCB FP 63 Amps 415 AC, 50 Hz, 25 KA with sheet metal enclosure complete all as specified and as directed.

Notes: - (For Ser Item No : 98.00 to 101.00): - (i) The quoted rate shall include minor items such as lugs, nuts and bolts, washers, top insulators, sleeves, provision of extra holes in bus bar etc. (ii) All internal wiring shall be done with suitable size of PVC insulated solid copper conductor FRLS cable conforming to IS-694. (iii) Panel drawing shall be got approved before placing of order from Engineer-in-Charge / GE. (iv) The bus connection for cable from main bus bar to outgoing MCCB will be connected through suitable rating bus bar strip type duly insulated. (v) Test certificate of panel board will be submitted by Contractor.

Material and labour in replacement for earthing complete with galvanized steel plate earth electrode 60cm x 60cm x 6mm thick buried in ground vertically to a depth not less than 1.5 metre below normal ground level connected to galvanized iron wire of 4 mm dia earth lead by means of bolts, nuts and washers made of galvanized iron protected by 40mm bore light grade GI pipe up 7.5 Rm with 4mm earth lead and connected for body earthing of feeder pillar box all as specified and including PCC (1:3:6) type C-2 pit and precast RCC (1:11 / 2:3) type A-1 pit cover slab of size 300 x 300 x 50mm with handle as shown in drawing funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal and salt in alternate layers including necessary earth work and excavation in hard / dense soil and removal etc complete all as specified in electrical plate No 3 of SSR Part - I 2020 and testing on completion complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement MCCB TPN 250 Amps, 415 Volts, 25 KA, 4 Pole, Ics=100% Icu, overload adjustable short circuit adjustable type including complete connection all as specified and as directed by Engineer-in-Charge.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 240 Sqmm 3.5 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Supply and laying, connecting and testing of XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 10 Sqmm 2 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are provided by the contractor without any extra cost.

Material and labour for plain cement concrete (1:4:8) (using 40 mm graded crushed stone aggregate) smooth finish to all exposed surfaces of roads, foot paths without using extra cement all as specified and directed by Engineer-in-Charge.

vishesh engineers

M/s. Aggarwal Engineers

Bidder Name

Sarbat Construction Co

M/s. Aggarwal Engineers

vishesh engineers