Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹74.8 LAccepted-Finance | L1 | Accepted-Finance Responsive | |
| 2 | L2₹83.1 L+₹8.3 L (11.1%)Accepted-Finance | L2 | Accepted-Finance Responsive |
Tender Value
₹89.2 L
EMD Value
₹1.8 L
Closing Date
12 Jun 2023, 3:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
EE, PBSD, APWD, Port Blair
EE, PBSD, APWD, Port Blair
Addition and alteration of First Floor Balcony and Ground Floor Extension portion of Balcony CS Bungalow under Sub Division - II, PBSD, APWD, Port Blair
2023_APWD_10488_1
NIT No. 16/EE/PBSD/2023-24
Open Tender
Civil Works - Buildings
Works
150 days
Port Blair
Please refer Tender documents.
4 documents required · 4 mandatory
₹0
₹1.8 L
22 Jun 2023
1 Jun 2023
12 Jun 2023
1 Jun 2023
12 Jun 2023
1 Jun 2023
Amount
Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.
All kinds of soil
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.
Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
Thermo-Mechanically Treated bars of grade Fe-500D or more.
Centering and shuttering including strutting, propping etc. and removal of form for
Foundations, footings, bases of columns, etc. for mass concrete
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)
Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.
In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
Providing and fixing M.S. Plate/sheet form with necessary self drilling screws or welding etc. complete as per the direction of Engineer in charge.
MS plain plate/ sheet 6 mm thick.
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :
Two or more coats on new work
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
Providing and applying SBR polymer (of approved make) fosroc brushbond RFX High performance elastomaric cementations water proof coating mixed with 4.85 ltr. RFX liquid and 3ltr. fresh water poured into a plastic or metal drum to mixed then mixing with powder component (15 kg) is added gradually to be liquid to avoid lump formation and mixed 2-4 minutes to produce a brush able consistency mix and apply two or more coats upto 1 mm thick as per the direction of Engineer-in-charge.
Painting with plastic emulsion paint of approved brand and manufacture of Indigo floor paint of platinum series or equivalent weather shade Terracotta Batch No. CA22814 or equivalent to give an even shade in walls and floor as directed by Engineer-in-charge.
Two or more coats new work.
Providing wood work in frames of false ceiling, partition etc. sawn and put up in position :
1st class Padauk wood Cat-I (A)
Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge.
25 mm wooden planking, tongued and grooved in false ceiling and walling including fixing with SS self drilling/tapping screws complete. (frame work to be paid separately )
1st Class Padauk wood Cat- I (A)
Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :
Thickness above 10 mm up to 25 mm
Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
Gutter (600 mm over all girth)
Providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia and size (Dash fastener to be paid for separately).
Providing and Fixing 3 mm thick Alumnium composite pannel (ACP) board for cladding/ceiling with necessary screws, bolts etc. as per direction of Engineer in Charge.
Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.
Upto 5mm depth and 5 mm width
Providing and fixing 12 mm thick toughen glass (customized size) including edge polished etc. complete and fixing with necessary beading, natural silicon sealent & screws etc. complete as per the direction of Engineer-in-charge. (Payment for beading shall be paid separately)
Providing and fixing decorative type beading for holding / supporting the glass panes etc. complete.
1st Class Padauk wood Cat- I (A) 23.1.1) Size 25 mm x 50 mm
Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/ 120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)
Providing and fixing 12 mm thick toughen glass as handrail with necessary Stainless steel finished bottom support and top rail fixed with necessary rubber fixtures screws adhesive etc. all complete as per the direction of Engineer-in-charge.
25 mm wooden planking, tongued and grooved in flooring including fixing with iron screws complete.
1st Class Padauk wood Cat- I (A)
Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :
12.5 mm thick tapered edge gypsum moisture resistant board
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
Supplying chemical emulsion in sealed containers including delivery as specified.
Chlorpyriphos emulsifiable concentrate of 20%
Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :
Along the external wall below concrete or masonry apron us- ing chemical emulsion @ 2.25 litres per linear metre includ- ing drilling and plugging holes etc.: 30.1.1) With Chlorpyriphos E.C. 20% with 1% concentration
Providing and fixing Stainless Steel curtain Rod (Heavy type) of standard quality. (25 mm dia)
Providing and fixing Brass curtain Holder (Decorative type) of approved quality with necessary screws etc. complete.
Providing and fixing curtain centre support wherever required of standard quality.
Providing and fixing curtain with superior quality cloth (Vimal or its equivlalent) including curtain stitching in frill model with Canvas, curtain tape ring etc. complete. (minimum cost range of curtain shall be `450/Mtr.)
Providing and fixing antique finished brass sliding door bolts, with nuts and screws etc. complete.
Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :
Providing and fixing bright finished brass handles with screws etc. complete:
Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles ( make Godrej or equivalent) including fixing with necessary screws etc. complete.
Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (Make of godrej or equivalent (heavy duty) product code no. 5959 (301715145D00052) ISI, IS : 3564, embossed on the body, door weight upto 60 kg and door width upto 950 mm), with necessary accessories and screws etc. complete.
SHIPRA CONSTRUCTION
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .