Civil Work

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.

All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form work for :

Foundations, footings, bases for columns

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases of columns, etc. for mass concrete

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : (copper oxidized as per IS: 1378)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete

Twin rubber stopper

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Electric resistance or induction butt welded tubes

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing bolts including nuts and washers complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).

Medium shade pigment using 50% white cement 50% Grey cement

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110 mm diameter

Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Single tee without door

110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofingn accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm)

White washing with lime to give an even shade :

New work (three or more coats)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :

New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :

Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe

32 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder :

Vitreous china

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

20 mm nominal dia Pipes

25 mm nominal dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

20 mm dia nominal bore

25 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

25 to 40 mm nominal bore

50 to 80 mm nominal bore

Providing and fixing brass bib cock of approved quality :

15 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length

15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15 mm nominal bore

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge.

Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-incharge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).

Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer-in-charge.

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Supplying and filling in plinth with pulverised sand under floors including watering, remming consolidating and dressing complete.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of stone aggregate 40mm nominal size, well rammed and consolidated and grouted with pulverised sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and fixing Chrome Plated Health faucet of approved quality with 1.0/1.2 m Flexible Tube and hook complete or as per the direction of Engineer in Charge.

Providing cement concrete surface drain including earth work excavation 10 cm thick base concrete and 15 cm thick side wall with 1:3:6(1 cement 3 sand:6graded stone agg. 40mm nominal size) cement concrete finished with 1:4 (1cement :4 sand ) a floating coat of neat cement inside the drain and its top and exposed surface and disposal surplus earth etc.,

23cmX 23cm surface drain.

Providing and fixing eaves or facia board with PVC/WPC board of 30 cm width of approved quality.

18 mm thick WPC Board

Extra for providing and fixing wid ties of 40x6 mm flat aluminium section.

Constructing masonry Chamber 90x90x100 cm inside, cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate of 50 mm nominal size) with RCC slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard size with CC 1:3:6.

Construction of soak pit 1.20 x 1.20x 1.20 m filled with brickbats including S.W drain pipe 100mm diameter and 1.20 m long completed as per standard design.

Construction of septic tank with cement concrete wall suitable section with CC 1:3:6 including pre cast RCC top 10 cm thick slab with CC 1:1.5:3 (1 cement: 1.5 coarse sand : 3 Graded stone sand: 8 Graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with water proofing cement mortar 1:4(1 cement : 4 fine sand) finshed with a floating coat of near cement 50 mm thick CC flooring 1:2:4 (1 cement: 2 coarse sand: 4 Graded stone aggregate) including RCC baffle wall 10 cm with terminal and two manhole covers of size 455 x 610 mm rectangular C.I cover (light duty) fixed in RCC slab and MS foot rest for manhole at 30 cm center to center all complete as per design drawing and direction of Engineer-in-charge.

100 users having inside dimension 8.10x2.10x2.20 including 30 cm free board.

Providing and fixing CP soap Dish with wall flage of standard size of approved quality. (Make Jaquar or equivalent).

Providing and fixing Upvc panel board for partition wall fixed to aluminium frame i/c necessary screw and other fitting etc. complete as per the direction of Engineer-in-charge (Frame work shall be paid separetely)

Providing and fixing vertical grabrail of size 600mm length of 32 mm dia of approved quality as per the direction of Engineer-in-charge

Constructing masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 30 kg (weight of cover 23 kg and weight of frame 15 kg) :

ELECTRICAL ITEMS

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Telephone socket outlet

TV antenna socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

1 run of cable

2 run of cable

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Supplying and fixing PVC batten/ angle holder including connections etc. as required

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, nterconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

4 way (4 + 12), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Above 35 sq. mm and upto 95 sq. mm

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required

80 mm dia

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

90 mm dia (OD-90 mm & ID-76 mm nominal)

Supplying of prewired LED tube lamp fitting 4, 1x20 W Essential Bright Batten Similar to make philips Cat : BN170C LED205-6500 SU L120 etc as required or similar in make : Havels, Syska, Bajaj, cromton.

Supplying of 15 W recessed mounted panel TRIM LED PANEL ROUND similar to Make : Havells, cat No LHEBLDP7IN1W015, 15 W, LED, 6000k or similar in make: PHILIPS, C&S, Bajaj, Crompton,

Supplying of LED Mirror light fitting to LED Batten as required Similar to make Bajaj Cat : BCLSB 05 WH complete etc as required, similar in make: Philips, Havels, Syska, crompton.

Supplying of LED Endura Bulkhead fitting Make:- Philips cat. No. WT202W LED65 NW PSU 52 PC or equivalent complete with all accessories etc as required. Similar in make: Havels, Syska, Bajaj, cromton.

Supplying of LED ADORE 9 Watt B22 WW 2 STAR LAMP Similar to make Havells, cat No LHLDEUEEMC8R009 or similar in make in philips, syska, Bajaj crompton

Supplying of AC ceiling fan 1200mm sweep Make : crompton 1200 mm EMPOWER 1STAR & ISI MARK Mode: ENERGIA, ISI and 1 star (White) or similar in make: Usha/Anchor/Bajaj/Orient/Haveels etc complete with all accessories etc as required.

Suppying of exhaust fan 225 mm sweep (Metal Body) Light Duty Make:- crompton Model-225mm DRIFT AIR PLUS METAL ANTI DUST or similar in Make:- Usha/Anchor/Bajaj/orient/Havells etc complete with all accessories etc as required.

Supplying of one number XLPE insulated PVC outer sheathed with galvanised round steel wire or steel stip armoured aluminum conductor power cable of 650 grade of size 3 1/2 x 95 sq. mm conforming to IS 1554 (Part-I) 1988 amended upto date.

Power safe enclosures conforms ti IS:8623, IEC: 60439 "G" frame Panel boards, O/G Four pole MCCBs G-Frame 250A "AA" frame MCCB 4 way outgoing Double door make: Havells cat No. IHVGF2500400-01 No.

Cable alley for 'G' frame panel boards outgoing four pole MCCB inncomer 'A' & "C" frame MMCB i/c 250a outgoing 3P GF 6way & 4p 2/4 way double door Make:- Havells cat Mo. ISSBOUO691-01 No.

Fixed thermal & fixed magnetic setting four pole MMCB 100 Amps breaking capacity 25 (KV) Make: Havells cat No. IHLGHF0100 # -01 No.

Fixed thermal & fixed magnetic setting four pole MMCB 40 Amps breaking capacity 16 (KV) Make: Havells cat No. IHLGHF0040 # -01 Nos

Supplying and fixing of SMC sintex box of inside dimension 650 mm x 350 mm x 250mm code No. GSIB-6535, etc as required.

Supplying, Installation, testing and commissioning of NVR suitable for 16 channel IP camera input 2 MP, 3 MP, 4 MP and 8 MP Network camera, 256 Mbps incoming band width with 2 SATA HDD code for each HDD support multi brand network cameras etc. complete as required. Make HIKVISION- Model:- DS-7716NXI-14 (16P)/45 or similar in make Dahua.

Supplying, installation, tsing &commissioning of IR Network DOME indoor camera, 4 MP resolution, 2.8 mm. 4mm 6mm fixed lens, lens, IR range 30m, IP67 protection, Make:- HIK VISION Model: DS-2CD2146G1-1(S) or similar in make Dahua.

Supplying, installation, tesing & Commissiong of IR Network Bullet Outdoor Camera, 4 MP resolution, 2.8 mm. 4mm 6mm fixed lens, lens, IR range 30m, IP67 protection, Make:- HIK VISION Model: DS-2CD2146GO or similar in make Dahua.

Supplying, installation, testing and commissiong of 8 Port Power Over Ethernet switch for cameras Make:- HIKVISION Model: DS 3E0109P-E/M PoE or similar in make Dahua

Supplying, installation, tesing & Commissiong of 4 Port Power Over Ethernet switch for Cameras Make HIKVISION Modal: DS 3E0105P-E/M or similar in make Dahua.

Supplying, Installation, tesing and commissioning of UPS of capacity 2.2 kva/24 v with 02 Nos 12V, 200 AH Tubular inverter Battery with racks for housing battery & invertor etc. complete as required, Make:- Microtek UPS JMSW pure sine wave and Tubular Inverter battery V-Guard VT 200 or similar in make-Luminious/LIV Guard.

Supplying, installation, testing and commissioning of 6 TB/6000 GB HDD Surveillance Hard Disk for video data backup storage in existing NVR rack etc. complete as required, Make: Seagate, Model: ST600VX0023 or similar in make zebronic, wd, scan Disc.

Supplying, Installation, testing and commissioning of NVR/DVR racks for CCTV in wall/frame with having connection power socket, 19" rack x 10 with lock and key arrangement etc. complete as required make plamtex or similar in make CP Plus, Lepose.

Supplying, installation, testing and commissioning of 43" full Ultra HD LED TV for wall mounting etc. completed as required, Make Samsung Neo series Ultra HD Smart LED TV UA43AUE65AKXXL (Black) or similar in make sony/LG/PHILIPS.

Supplying & installation of chordless Mouse Make: Dell WH118 Wire less mouse or similar in lenova, HP.

Supplying & fixing of PVC Box for holding CCTVDVR/NVR/POL and CCTV SMPS smart management power socket ideal for 4/8 channel CCTV system for both indoor and outdoor purpose Make: Bectro or similar in make syntex/press Fit.

SITC of minimum 1.5 Ton 5 star (As per 2018 BEE star rating Inverter High wall split type Air conditioner (Twin/dual rotary commpressor 1 Phase 220 volt) Make: BLUESTAR, Model-Bl/BO-SCNHW18PAFU or equivalent with minimum cooling capacity ranging from 2000 watts to 7000 watts (condenser coil must be of copper material) i/c cutting, drilling holes on the wall for passing gas pipes, fixing suitable size PVC pipe on the wall through the holes and cementing, painting to give an even look and smooth finish, wrapping PVC non adhessive white tape over insulation of gas pipe, fixing the outdoor unit on brackets etc as required and as the direction of Engineer-in-charge.

SITC of minimum 2 Ton 5 star (As per 2018 BEE star rating) Inverter High wall split type Air conditioner (Twin/dual rotary commpressor 1 Phase 220 volt) Make: BLUESTAR, Model-Bl/BO-SCNHW18PAFU or equivalent with minimum cooling capacity ranging from 2000 watts to 7000 watts (condenser coil must be of copper material) i/c cutting, drilling holes on the wall for passing gas pipes, fixing suitable size PVC pipe on the wall through the holes and cementing, painting to give an even look and smooth finish, wrapping PVC non adhessive white tape over insulation of gas pipe, fixing the outdoor unit on brackets etc as required and as the direction of E-in-c.

Supplying and fixing of 4KVA voltage stabilizer for 1.5 ton Air conditioner as required of Make V Guard Model VND 500 (Voltage Range 150V-285V,15Amps) or equivalent.

Supplying and fixing of 4KVA voltage stabilizer for 2 ton Air conditioner as required of Make V Guard Model VND 500 (Voltage Range 150V-285V,15Amps) or equivalent.

Supplying, Installation, testing (Including fuel, Lub oil, coolant etc) and commissioning of 'Silent Type' Three cylind diesel Generating set, vertical Liquid cooled diesel oil engine similar to KOEL GREEN Make 3R1040TG1 DIESEL OIL ENGINE Model 42 HP @ 1500 RPM directly couled with AC Alternater 3 phase 415 volt 50 Hz @ 0.8 PF self excited, self regulated, designed to run at 1500 RPM suitable for 20 KW/25KVA DG sets with Acoustic Enclosure (Sound Proof) and suitable extended exhaust as per central pollution control Board (CPCB-II) approved DG set with inbuilt single EB Automatic Mains Failure Board (AMF). make Koel Green engine and Koel Green alternater or equivalent.

MM KAILASH CONSTRUCTION PVT LTD

O P KANDOI AND COMPANY PVT LTD

CSE CONSTRUCTION (INDIA) PRIVATE LIMITED

P G EAPPEN CONSTRUCTION PRIVATE LIMITED