PROVISION OF CERTAIN MINOR WORKS UNDER GE I CG BHUBANESWAR

Amount

B/R PORTION Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for Hardcore of broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100mm thick Cement concrete,1:4:8 type D-2 (using 40mm graded stone aggregate) complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-30 Grade in grey cement and pigment laid over and including 50 mm thick sand filling complete all as specified and directed.

Providing and laying factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M & L for preparation of concrete surfaces over 10cm girth or width, not otherwise described and applying two coat of Synthetic enamel paint over one coat of primer on kerb stone complete all as specified and directed.

Removing excavated material to a distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Material and labour for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc , complete all as specified and directed.

Material and labour for brushing neat cement slurry with 3 Kg of cement per Sqm in floors as well as walls complete all as specified and directed.

Material and labour for vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Taking down cement plaster on brick walls, etc including raking out joints, hacking for key, crubbing down with water, etc complete all as specified and directed.

Material and labour for glazed ceramic tiles in vertical surface 350x250x7 mm/450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for 18-20 mm thick medium density fibre board, exterior grade, fixed to timber framework with screws as required complete all as specified and directed.

M&L for 0.9 mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

M&L for 2nd class hardwood plain fillets, square, rectangular or triangular in section, sectional area exceeding 13 Sqm but not exceeding 25 sqm, clean sawn, secured with nails or brads as required complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description not exceeding 10cm width or girth and applying two coats of synthetic enamel paint over and incluidng a coat of pink primer complete all as specified and directed.

S&F Continuous (piano) hinges, stainless steel, bright finish or electrogalvanised with 40mm width of flaps complete all as specified and directed.

S&F Ball catches (magnetic) with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F 50mm dia, polished, hard wood knobs fixed with screws complete all as specified and directed.

S&F powder coated aluminium for shutters (minimum thickness of powder coating 50 micron) of doors, windows, ventilators, cupboards & cabinets including, providing and fixing tracks / hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per the directions of Engineer-in-charge.

Providing and fixing steel roller for uPVC / aluminium sliding window, cupboard / cabinet shutter made of plywood or glass of any type with necessary screws, fitting & fixtures etc. complete all as specified and directed.

S&F 5.5mm thick sheet glass in area exceeding 0.5 sqm in each pane fixed in cabinets, cupboards, hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes as required complete all as specified and directed.

S&F cabinet frame & table made of 19mm thick BWP ply including 1mm thick laminate on both sides as in boxes, shelves, racks and shutter drawer etc and including PVC edge banding tape (Make: Rehau or equivalent) with exposed side is 1 mm thick and inner side 0.8 mm fixed with hot glue by edge banding machine complete all as specified and directed.

S&F stainless steel soft closing spring hinges (hydraulic type) of approved make/ board to cupboard shutters with full threaded steel screws & making necessary recess in board and finished etc complete all as specified and directed.

S&F 200mm long stainless steel fancy handle complete all as specified and directed.

S&F stainless steel telescopic drawer channels 500mm long suitable for 35 kg weight with screws etc complete all as specified and directed.

S&F 12 mm thick BWP ply including 1mm thick laminate on both sides as in wall panelling including framework made with 19 mm thick BWP ply board patti of size 50mm wide in horizontal and vertical grid of spacing 600mm centre to centre horizontally and 900mm centre to centre vertically including screws complete all as specified and directed.

E&M PORTION Supply and Laying GI pipe medium grade with all fittings and clamps laid in Wall/floor of the Size 50 mm bore of pipe complete all as specified and directed.

Supply and fix gun metal gate valve size 50 mm bore with iron wheel screwed both ends for iron pipe and fixed complete all as specified and directed

Supply and fix CI Non - Return Valves without by pass arrangement , ISI marked , heavy duty , flanged type including rubber sheet & nut bolts etc for the 50mm Dia conforming to IS-5312 Part-I PN 1.6 complete all as specified and directed. Make - Kirloskar/Upadhaya/Leader/Zoloto or equivalent

Supply and fix GI Union size 50 mm bore Both ends screwed to iron pipes, or one flange end bedded in red lead cement,and other end crewed to iron pipe, etc. complete all as specified and directed.

Supply and fix Horizontal Openwell Submersible Pump Set,3 HP,440 volts,3 Phase,Suction x Delivery ( 50mm x 50mm ) complete all as specified and directed. Make-Crompton,Cat No- OWNH32(1HP)G-27 3 HP or equivalent of KIRLOSKAR

Supply and fix DOL Starter,3 HP,3 Phase,415 volts,50 Hz complete all as specified and directed . Make-Crompton,Cat No- DOL 4065-2S3M or equivalent of L&T/Siemens.

Supply and fixing Submersible cable 6 Sqmm, 3.0 Core, Copper Conductor Including PVC Conduit 25 MM dia Complete all as Specified and directed. Make of Wire Polycab/finolex/Plaza

Supply and fix in repair foot valve as per IS-4038 of cast iron with brass diaphragm heavy duty screwing type 50 mm Dia complete all as specified and directed.Make-Kirloskar/Kartar/Leader/ Upadhaya

Supply and fix Bus bar Chamber TPN 63 Amps including aluminium busbar with 4 O/G Ways and all accessories with MS angle and frames complete all as specified and directed, Make- C&S/Havells /Indoasian or Equivalent

S C MOHANTY (BID ID -3411603)