SPECIAL REPAIR TO BUILDING NO NP 29 AND OTHER SANCTIONED WORKS UNDER GE (WEST) FEROZEPUR CANTT

Amount

Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass vegitation including roots near out let of RWP and OHT staging area or specifically ordered by Engineer-in-Charge in writing complete all as specified and directed.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified and directed.

M&L 15 mm thick rendering of mortar in cement mortar1:4 with water proofing compound @3% by weight of cement or as per manufacturer instructions will be on surface to have a smooth surface for laying of water proofing membrane. Note: WPC shall be measured and paid for separately.

Supply only water proofing compound.

M&L 80mm thick average consolidated thickness mud phuska on flat roof including 25mm thick mud plaster complete all as specified and directed.

S&F 40 mm thick brick tiles laid on mud mortar and joints grouted flus in cement mortar 1:3 mixed with 5% of crude oil by wt of cement on mud phuska complete all as specified and directed.

All as per Srl item No 06 here-in-before but except tiles. Note: Servicable tiles obtained from diamanantling shall be re-used.

M&L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and directed.

M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application including bitumen primer complete all as specified and directed.

M&L two coats of solar reflective bituminous aluminium Paint @ 0.1 kg per sqm over APP membrane complete all as specified and directed.

Taking down cement plaster brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L rendering/plastering on external surface of the wall of 15mm thick in cement mortar 1:4 on brick wall surfaces, surfaces finished even and fair complete all as specified and directed.

M&L 10mm thick rendering in cement mortar 1:6 on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L 5mm thick rendering in cement mortar 1:3 on concrete surfaces, finished even and smooth without using extra cement as in ceiling complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applyings two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L applying wall putty of 1mm thick interior/exterior on wall surfaces finished smooth and even complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls & applying three coats coats of white wash complete all as specified and directed.

M&L preparation of new plastered surfaces and applying three coats white washing on ceiling surfaces complete all as specified and directed.

M&L complete removal of existing treatment of wall suface and applying two coats of oil bound distemper over a coat of primer on a coat of 1mm thick wall care putty complete all as specified and as directed.

M&L preparing new surfaces of steel of any description,not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

M&L preparation of old steel surfaces of any description not otherwise description over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and directed

M&L preparing new surfaces of wood and wood based surfaces of any description,not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L preparation of old wood or wooden based surfaces of any description not otherwise description over 10cm width or girth and applying one coat of synthetic enamel paint on old painted surfaces all as specified and directed

Dismantling of floor hearth and wall tilling incl mortar beding removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Marble work 18mm to 20 mm thick in steps ,jambs, pillars,cooking platform and like including pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade other than white and black types over a 15 mm thick screed bedding in cement mortar 1:6 complete all as specified and directed.

M&L non-skid coloured ceramic tiles of 7 to 8 mm thick , area of each tile exceeding 0.11 sq m but not exceeding 0.18 Sqm in floors set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match over a screed layer of 15 mm thick in cement mortar 1:6 complete all as specified and as directed.

M&L non-skid coloured ceramic tiles of 7 to 8 mm thick , area of each tile exceeding 0.11 sq m but not exceeding 0.18 Sqm as in skIrting/dado set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match and backing with 10 mm thick in cement mortar 1:4 complete all as specified and as directed.

M&L glazed coloured and cereamic tiles in vertical surfaces size 450mmX 350mm and 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over backing coat 10mm thick in cement mortar 1:4 for laying skirting dados and vertical surfaces all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches pillars etc.., but excluding ashlar facings dressed stone work and precast concrete articles complete all as specified and as directed.

M&L brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified and as directed.

All as per Srl item 30 here-in-before but using old bricks retrieved from demolition under item 29 here-in-before including cleaning and removal of mortar from old bricks.

M&L Plain Cement Concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) min radius of 75mm thick as in roof and parapet wall junction, roof benching, kerbs, mud stop, coping, rounded or chamfered on edges, including necessary sloping on roof including formork complete all as specified and directed.

M&L form work to chajjas, including edges complete all as specified and directed.

M&L RCC 1:1.5:3 , type B-1 (using 20 mm graded aggregate) as in chajjas etc. complete all as directed.

Taking down chowkkats or frames area not exceeding 1.5 Sqm each ( without taking off shutters from the frames) complete all as speicified and directed.

All as per Srl itrem No 35 here-in-before but exceeding 1.5 Sqm and not exceeding 4.0 Sqm.

S&F factory made box type side hung steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07 complete all as speicified and directed.

S&F factory made box type side hung steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07 complete all as speicified and directed.

S&F factory made box type steel ventilator side/top hung with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07 complete all as speicified and directed.

M&L forming jambs etc built in cement mortor 1:6 to openings including cutting toothing and properly bonding into to old work also facing ,jointoing and pointing to match to existing work complete all as specified.

M&L pressed steel frames made of 1.25mm thick MS sheet of profile 105mmx60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

All as per Srl item 41 here-in-before but size 125mmx60mm with double rebate.

M&L PCC 1:3:6, type C-1(using 20mm graded stone aggregate) as in filling of steel chowkhats complete all as speicified and directed.

S&F 35mm thick second class hard wood plain framed, panelled shutters (two panel), with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commencial veneering on both faces. The size of rail and style as per IS:1003 (Part I), Kiln seasoned and chemically pressure treated complete all as speicified and directed.

S&F 35mm thick second class hard wood glazed and skelton shutters,open rebated and prepared to receive glass gauze,etc (without sash bars),edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR part-I section 8 clause 8.24(a) fitted to chowkat all as specified and as directed.

M&L galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as speicified and directed.

S&F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples in repairs complete all as speicified and directed.

S&F 3 mm thick ordinary quality sheet sheet glass glazing with oil putty and glazing clips fixed complet to wooden/Steel window not exceeding 5 sqm in each pane complete all as speicified and directed.

Hacking out old broken glass from metel frame including punching or drilling out old glazing pins/ spring clips and providing and fixing new complete all as specified and directed.

Dismantling of boarding of any description and in any position complete all as speicified and directed.

S&F 16-18 mm Solid PVC board plain colour ,fixed with screws or adhesive with complete accessories (magnetic catcher, knobs) as in shelves/shutters with rebates fixed on PVC on three sides as in supporting block to shelves complete all as speicified and directed. Makes : Rajshree, Echon or equivalent approved make as approved by GE.

S&F continuous (piano) hinges, mild steel bright finish or electro galvanised with flap (when open) 40 mm, fixed with steel screws complete all as speicified and directed.

S&F Hasp and staple of aluminium anodized, safety type, 100mm long, fixed with screws complete all as specified and as directed.

M&L solid PVC door frame of size 50mmx47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube supplying and fixing as per specification complete all as speicified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail either side & as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement suppling & fixing in the frame at site as per specification & drawing complete all as speicified and directed.

S&F PTMT tower bolts, 200 mm long and fixed with steel screws complete all as speicified and directed.

S&F PTMT butt hinges,100mm long, fixed with steel screws with brass /bronze hinges pin complete all as specified and directed.

S&F PTMT handle 125mm long fixed with steel screws complete all as speicified and directed.

S&F aluminium alloy, anodised, sliding door bolt 300mm length,with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as speicified and directed.

S&F 200mm long aluminium, anodised barrel tower bolts of extruded section, complete all as speicified and directed.

S&F 150mm Extruded aluminium alloy handle complete all as speicified and directed.

S&F mild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as speicified and directed.

S&F 150 mm Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and as directed.

S&F galvanised steel water tubes 15 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as speicified and directed.

S&F galvanised steel water tubes 20 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as speicified and directed.

Taking up or down 15 mm existing steel tubing and connections and re- fixing old steel tubing and connections in new or old position complete to walls and ceiling or laid in floors complete including cleaning the steel tubing all as specified and as directed. Notes:- Cost of new fittings if required shall deemed inclusive in the quoted rate.

All as per Srl item No. 66 here-in-before but 20mm dia.

S&F Rotational moulded Polyethylene water storage tank of 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position including taking down old PVC water tank complete all as specified and as directed.

S&F 20mm ball brass valves high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed to union etc as fixed in repairs all as specified.

S&F gunmetal gate valve of 20mm dia with iron wheel head screwed both ends for iron pipe all as specified and directed.

S&F in repair 125mm dia CP grating doom with waste hole of PTMT (minimum weight 40 gms) complete all as specified and directed.

S&F 125mm PTMT grating doom with waste hole of PTMT (minimum weight 40gms) all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth;. not exceeding 10 Sqm on plan and not exceeding 1.5m in depth and getting out in soft/loose soil for foundation or laying cable/pipe etc complete all as specified.

Returing, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all as speicified and directed.

Removing excavated material as soil exceeding 50m and not exceeding 250m, depositing where directed at a level not exceeding 1.5m above the starting point complete all as speicified and directed.

M&L plain cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregate) as in foundation filling as mass concrete complete all as speicified and directed.

S&F salt glazed stonewire drain pipe 150 mm internal diameter grade A laid in trenches jointed and tested complete all as specified and directed.

M&L PCC 1:3:6. type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore complete all as speicified and directed.

M&L Reinforced Precast cement concrete 1:2:4, type B1 (using 20 mm graded granite stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:6. Note: Reinforcement shall be measured and paid for seperately.

M&L for Mild steel TMT bars 10mm dia and over,cut to length,bent to shape required,including cranking,bending, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified & directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc, including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as speicified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including distance pieces and stack clamps as in rain water pipes , complete all as specified. Note:- fittings shall be measured and paid for separately.

S&F 110 mm bore PVC (SWR) bends/shoe any radius fixed to walls including distance pieces and stack clamps complete all as specified.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as specified.

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement 75 mm dia outlet complete all as specified.

S&F 75mm dia PVC (SWR) bends any radius complete all as speicified and directed.

S&F 110 mm dia PVC (SWR) bends any radius complete all as speicified and directed.

S&F stainless steel sink with drainage board made of of 1.00mm thick sheet for kitchen or laboratory with plugs washers38/40mm diaa PVC waste pipe and including 38/40mm dia CP waste coupling fixing cast iron cantilever brackets and connecting union to pipe over all size 915mmX460mm bowl size 410mmX330mmX160mm complete all as specified and directed.

Supply & fixed stainless steel plate rack 1.00 mm thick racks of standard qality 900mm x 750mm x 250mm size in repair including necessary shelves etc complete as fixed repairs and complete all as specified and directed.

S&F Wash hand basin, flat back 550mmx400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified and directed.

S&F CP Soapdish Oval /squaretype as fixed in repairs and all as specified and directed.

S&F Vitreous china white squatting pan orrissa pattern of size 580mm x 440 mm with integral foot rests including necessary lime concrete and 100 mm bore cast iron ‘P’ trap with 550mm to 600 mm long neck for connecting WC to branch piece with cement joints, fixed as in repair complete all as specified and directed.

S&F in repair PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc and fixed in repairs complete all as specified and directed.

S&F 20mm dia mild steel PVC colour powder coated curtain rod with fancy type brackets including with all fittings as fixed in repairs complete all as specified and directed.

S&F in repair 15mm bore bib tap fancy type of chromium plated cast copper alloy brass, screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 15mm bore pillar tap,fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repair 15mm bore fancy type chromium plated Stop cock cast copper alloy screwed down, high pressure screwed both ends for iron pipe or union as fixed in repairs complete all as specified and directed.

S&F in repair chromium plated shower rose with or without swivel joints any size including fixing to steel pipe or union complete all as specified and directed.

S&F towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats (Min wt 190 gm) complete all as specified and directed.

Demolition of Stone slabs and tiles laid bedded pointed in mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

M&L providing and laying 60mm thick factory made chamfered edge coloured cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed

M&L 75mm thick plain cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregates) as in sub base of floor complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6, type C-2 (using 20mm graded stone aggregate) as in plinth protection, shall be laid in 1:20 slope. The concrete shall be laid at a stretch not exceeding 3-meter in length. Joint gap between the adjoining slab, at corners and at junctions of wall shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen of grade 85/25 garde mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3-meter interval at corner and junction walls complete all as specified and directed.

Demolition of un-reinforced cement concrete in any position complete all as specified and directed.

M&L 50 mm thick PCC, type B-1, 1:2:4 (using 20mm graded aggregate) as in flooring in , surface finished even and smooth without using extra cement complete all as directed.

M&L chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors as in floor set and jointed in neat cement slurry over and including 15mm thick screed in cement mortar 1:6 and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.

Dismantling of steel work including doors ,gates but excluding framed truss etc complete all as specified and directed.

M&L roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe 410-W (Gde E-250) Quality 'A' including fabrication, erraction and fixing complete all as specified and directed.

M&L framed work such as grills grating etc with ends of bars shoulders ans or riveted, or forged in to spikes: framed guard bars barred iron doors ladders framed balusters walk way railing framework of water cooler stand , angle iron in stair steps, iron gate and similar work conforming to fe 290.Gde E-165 complete all as specified and directed.

S&F 1.00 mm thick mild steel, plain sheet in gates and similar work cut to size ,holes punched including round headed screws clout nails or revits and fixed to steel framing with plain 40 mm lap joints with rivited or welded including bending or turning up etc all as specified and directed.

Dismantling plain or corrugated AC sheet/fibre sheet on roof covering complete all as specified and directed.

S&F Pre painted galvalume aluminium Zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws complete all as specified and directed.

Surface excavation in soft /loose soil not exceeding 30 cm deep and averaging 15 cm deep and getting out complete all as specified.

Removing surplus spoil to a distance not exceeding 50 m and depositing where directed at a level not exc 1.5 m above the starting point.

All as per Serl Item No 30 here-in-before but half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Use & waste of formwork to sides of concrete foundations, footings, bases or column, raft and raft beams,sides and soffits if any of foundations and plinth beams and similar work,vertical or batter etc rough finished surface of concrete complete all as specified and directed.

Use & waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions ect rough finished surfaces of concrete complete all as specified and directed.

Use & waste of formwork to sides and soffits of floor or roof beams, beams haunchings, girders, bressummers, lintels, cantilever, shelves including supports, overhangs, etc also splays between floors and beams etc rough finished surfaces of concrete all as specified and directed

Use & waste of formwork to edges of rough finished surfaces concrete flats, treads breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 10 cm but not exceeding 20 cm wide complete all as specified and directed.

M&L RCC 1:1.5:3, type -1 (using 20mm graded stone aggregate) as in foundations including rafts, footings, foundations beams , bases of column etc complete all as specified and directed.

M&L RCC 1:1.5:3, type -1(using 20mm graded stone aggregate) as in columns, pillers, piers, posts and structs etc complete all as specified and directed.

M&L RCC 1:1.5:3, type A-I (using 20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

M&L RCC 1:1.5:3, type A-1(using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

All as per Srl item No 80 here-in-before but 5 mm dia and over upto and including 10 mm dia in stirrups spaces and binders.

M&L 15mm thick cement plaster in cement mortar 1:4 on brick or concrete surface finished even and fair without using extra cement complete all as specified and directed.

M&L hard core of brocken bricks of gauge not exceeding 63 mm deposited spread and leveled in layers not exceeding 15 cm thick watered and ramed to a true surface complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8, type D-2 (using 40 mm graded stone aggregate ) as in sub base for floors etc cement complete all as specified and directed.

M&L precast machine pressed cement concrete interlocking paver blocks of any shape and size confirming to IS 15658-2006 of 60 mm thick M-35 grade, glossy type with grey cement and pigment laid dry over a layer of 25 mm thick sand cushioning complete all as specified and directed.

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified.

M&L glazed coloured designer ceramic tiles of size 200mmX300mm and 7mm thick or 300mmX450mm and 7mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry over 10mm thick rendering in cement mortar 1:4 and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.

S&F factory made second class hard wood 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated cement complete all as specified and directed.

S&F powder coated anodised aluminium door, window , ventilator frame including shutter etc fixed / sliding or pull and push type in shutter frames or shutters with two/three track sliding aluminium frame of Jindal /Hindalco (or) Equivalent make of approved size with power coating any colour minimum thickness 50 micron including necessary joining cleats, glazing clips, powder coated aluminium snap beading, screws etc complete all as specified as per manufacturers instructions. Note: Glass Pane and EPDM Rubber beading/gasket shall be measured and paid seperatley.

S&F 5.5mm thick sheet glass, ordinary quantity,in squares exceeding 0.5 sqm each pane complete all as specified and directed.

S&F EPDM Rubber beading around glass in aluminium windows /ventilator shutters.

S&F Vitreous china white wash down water closet (pedestal pattern) including PVC seat cover and connection to drain or out going pipe and to flushing pipe anti-syphonage pipe etc cement complete all as specified and directed.

S&F in Vitreous china white squatting pan orrissa pattern of size 630mm x 450 mm with integral foot rests including necessary cement concrete and 100 mm bore cast iron ‘P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, fixed as in repair cement complete all as specified and directed.

S&F 10 litres capacity PVC low level flushing cistern (white) with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc complete all as specified.

S&F Wash hand basin, flat back 550mmx400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified and directed.

S&F 15mm size PVC connection with PTMT nuts of length 450 mm fixed cement complete all as specified and directed.

S&F PVC waste pipe of 32mm dia for Wash Hand basin/Urinals etc cement all as specified and directed.

S&F Urinal flat back vitreous china (White), of size 465mm x 365mm x 265 mm with grating, union for discharge pipe, spreader & 40mm dia PVC waste pipe upto floor trap cement complete all as specified and directed.

S&F 15mm bore dia fancy type chromium plated Stop valve screwed down, high pressure with crutch or butter fly handle cement complete all as specified and directed.

S&F 15mm bore dia fancy type chromium plated Bib tap with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule cement complete all as specified and directed.

S&F Corner glass shelves 300 mm radius, 8mm thick as per sample radius for bath room, fixed on suitable support of brass chromium plated clips cement complete all as specified and directed.

S&F chromium plated shower rose 125mm size with or without swivel joint for fixing in 15mm dia pipe cement complete all as specified and directed.

S&F Towel rail 600mm long of brass chromium plated fixed with & including CP brass screws & wooden/Plastic cleats (min. weight 170 gm) cement complete all as specified and directed.

S&F 500 litres capacity Water storage tanks rotational moulded, triple layer polythene (cyindrical vertical with closed top) hoisting and fixed in position on roofs cement complete all as specified and directed.

S&F Ball valve of PVC, 20mm bore, high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed cement complete all as specified and directed.

S&F 15mm bore dia Gun-metal,globe or gate valve screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union fixed in repairs cement complete all as specified and directed.

S&F 15mm bore GI tubes, medium grade with all fitting and fixed complete to walls and ceilings or laid in floors.

All as per Srl item item No 151 here-in-before but 20 mm bore tubing.

All as per Srl Item No 82 here-in-before but 75 mm dia pipe.

S&F 110mm bore dia PVC (SWR) pipes, Single socketed, in any length with rubber ring jointed in cement mortar and fixed to walls complete all as specified. (fitting measured separately).

S&F 75mm bore dia PVC (SWR), floor trap, Plain with grating including jointing with solvent cement cement complete all as specified and directed.

S&F 110mm bore dia PVC (SWR) vent cowl cement complete all as specified and directed.

Cutting into existing manholes for connecting new drains 150mm dia,making good to pipe & rendering,cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished & reforming benching as required complete all as specified and directed.

M&L Preparation of new plastered surfaces wall and applying two coats of Oil bound distember over a coat of primer complete all as specified and directed.

S&F Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and directed.

S&F Mild steel plates(plain or chequered) channels,square cut or notched(ordinary and counter sunk) forming holes,without any attachment and fixing complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other,or screwed bolt ends,each screwed end to be fitted with washers and one hexagonal or square nut,exc 5 cm long and n.exc 10 cm long and dia of shank 11 to 15 mm etc complete all as specified and directed.

M&L plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in walls or retaining walls,any thickness, sizeor shape including pilasters, buttressescolumns, pillars,boundary pillarsand posts(including caps and bases) complete all as specified and directed

S&F 40mm bore tubes, medium grade, galvanised, with all fitting laid in trenches in replacement complete all as specified and directed.

S&F 20mm bore tubes, medium grade, galvanised, with all fitting laid in trenches in replacement complete all as specified and directed.

S&F gunmetal, globe or gate valve of 40mm dia with iron wheel head screwed both ends for iron pipe all as specified and directed.

Cutting existing CI/GI pipe 40/50/80/100 mm bore including run lead joints of suitable size with necessary fittings complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

S&F Powder coated (any colour) (minimum thickness of powder coating not less than 50 micron) for aluminium windows & ventilators shutters, fixed type without sash bar, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed.

M&L anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement complete all as specified and directed.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.5 sq. m in each pane complete all as specified and directed.

S&F solar control film 25 micron reflective type sticked to glass panes as per manufacturers instruction complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:6 on any face of brick walls or concrete surfaces, finished fair and even complete all as specified and directed.

M&L preparation of new wall surfaces and applying three coats of white wash complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applyings two coats of cement base paint over a coat of primer complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.50cum, getting out, returning, filling, in and ramming earth or broken rubble mixed with earth around in layers not exceeding. 25cm, watering and removing surplus soil to distance not exceeding 50m and making good surface in soft/loose soil complete all as specified and directed.

M&L 75mm thick hardcore of gauge not exceeding 63mm graded stone aggregates, deposited, spread and levelled in layers not exceeding 15cm thick including watered and rammed to a true surface complete all as specified and directed.

M&L 50 mm thick PCC, type B-1, 1:2:4 (using 20mm graded aggregate) as in flooring in, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L Mild Steel work as in roof truss (framed) trussed, purlins crane gantries, rails and fastenings and heavy bracket framing (Beam tee, angle channel or flat sections) inclusing distance pieces,cleats etc Fe 410-W (Gde E-250) quality B complete all as specified and directed.

S&F 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with J- type or L- type hook bolts complete all as specified and directed.

Taking down carefully copper /aluminium point wiring (light, fan , socket or power ) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keetping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M &L Point wiring complete with 1100 volts grade PVC insulated unsheathed FRLS cable of copper conductor, multi stranded of size 1.5 sqmm, single core, in and including rigid non-metallic PVC conealed conduit, with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and existing MS pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 sqmm unsheated stranded copper conductor with green PVC insulation connected to common earth dolly complete all as specified and directed for the followings :- (a) One light/fan/Bell Point controlled by one single pole one way switch.

(b) One socket outlet on the same board controlled by one single pole one way switch

(c) One 5 amps socket outlet independent controlled by one single pole 5 Amp switch.

All as per Srl Item No 181 here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 Sq mm PVC insulated copper conductor and 2.5 Sqmm copper conductor for continuous earthing complete.

Supply & Fixing Switch piano flush type single pole one way 5/6 Amp complete all as specified and directed.

Supply & Fixing Switch piano flush type 15 amps, single pole one way duly ISI marked complete all as specified and directed.

Supply & fixing Socket outlet 2 in one , 5/6 Amps flush type ISI marked complete all as specified and directed.

Supply & Fixing Socket outlet, 2 in one 6 pin 5 and 15 Amps piano flush type ISI marked complete all as specified and directed.

Supply & Fixing bell push flush type 5 Amps duly ISI marked complete all as specified and directed.

Supply & Fixing ceiling rose, PVC/Polycarbonate,isolated three terminals complete all as specified and directed.

Supply & Fixing Lamp holder PVC/ Polycarbonate, isolated with back plate suitable for batten fittings including 10W LED Bulb complete all as specified and directed.

Supply & Fixing bell ding dong type AC 230 Volt single pole complete all as specified and directed.

S&F in repair stepped type electronic fan regulater flush type on the existing phenolic laminated sheet etc. as reqd complete all as specifed and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed.

S&F LED tube light fitting 1X18 W decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Makes. Cat Part No LHEXBLP7UN1W018 of make "Havells" or techno-commercially equivalent in approved makes.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series TPN DBs (Vertical type)fitted with ABS frame and 415 volts 200 Amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matchingcomplete all as specified and directed.

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 8 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and directed.

Supply & Fixing MCCB 100 Amps, 415 volts, 16 KA, 4 Pole complete all as specified and directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

Supply & Fixing in repair MCB single pole (SP) 240 volts, 40 Amps, 10 KA 'B' Series complete all as specified and directed. Note : 40 Amps 'B' series SP use for TPN DB Outgoing purpose

Supply & Fixing MCB, Single Pole and neutral 240 V, 32 Amps 10 KA 'B' series complete all as specified.

Sheet Metal Enclosures with Socket plug top and MCBs Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 20 Amp complete all as specified and directed.

Supply & Fix in repair sub main wiring of 4 sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor with earth wire of 4.0 sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor including PVC conduit pipe 25 mm dia complete all as specified and directed. Note: Two run of single core 4 sqmm cable and one run single core 4.0 sqmm cable for earth wire and including conduit pipe 25 mm dia shall measured as one length).

M&L for sub main wiring with two single core PVC insulated FRLS cable with Copper conductor unsheathed cable of size 2 x 6 sqmm drawn through in and including PVC Concealed with 1 x 6 sqmm PVC insulated copper conductor single core for continuous earthing complete including PVC conduit 25 mm dia complete all as specified and directed. Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0 Sqmm and one run of 6.0 Sqmm PVC insulated copper conductor single core,one run of PVC conduit shall be measured as single run)

M&L earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm and 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate, excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009) complete all as specified and directed.

Supply and lay cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 Sqmm 4 core complete all as specified and directed.

M&L bricks common burnt clay building bricks, sub-class ‘B’ designation 75 laid dry width wise acrose the line of cable in trenches for protection of undergroud cable complete all as specified and directed.

S&F mild steel galvanised iron pipe light grade (ISI marked) 40mm bore for passing of earth lead laid in trenches fixed to walls laid under floors, roads including all fittings i.e MS clamps nuts & bolts etc as required complete all as specified and directed.

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 4 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and directed.

Supply and fixing single pole neutral (SPN) 32 AMP rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all specified and directed.

Supply and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including4mm suspension wire, two single core cables flat or circular of stranded conductor of 10.0 Sqmm Complete all specified and directed.

Supply and fixing wall mounting fan 400mm sweep 230 Volt black/white paint including all acesary complete all as specified and directed. Makes: Havells cat part no FHWGNSTBLK16 or or techno-commercially equivalent in approved makes.

Supply, installation,commissioning & testing Double Door refrigerators electric driven (Single phase), 230 V with following specification: (a) Cap - Min 310 Litres (b) Cooling Feature- Twin Cooling Plus,Smart Conversion-5 Mode,Power Cool Function, Power Freeze Function, Non Frost,Multi Flow (c) Refrigerator Feature- Deodorizer,Shelf Material-Toughened Glass, (d) General Feature-Door Alarm, Refrigerant R-600A/R-134A,Compressor- Digital Inverter Compressor, EER- More than 4.2, with 5 Star rating or as per market availablity, Non CFC including electric connection complete all as specified and directed.

Supply and fixing double door , top operning hinged type door with PUF type insulation, manually deforested, direct cooling complete with intereior chamber material prepainted sheet, of 400 ltr capacity, , Eco friendly, AC reciprocating compressor, having -20 degree celcius minimum achievable temperature at 32 degree centigrade, single phase 230 V complete all as specified and directed with one year full warranty.

Supply and fixing Water cooler fully stainless steel, electric driven single phase having having approx storage capacity of 150 litres and nominal cooling capacity of 150 Litres per hour and conforning to IS:1475 (Part 1): 2001 latest, Imnput Voltage 230/240 Volt, 50 Hz, AC, Single Phase with 1.5 m length of 3 core cable conforming to IS:9968 (Pt.1) or IS:694 provided and push type water taps , complete all as specified and directed.

M&L Joist, channel, angle, or tee sections, fixed independently, withoutconnecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated), Fe-290 (Gde E-165) complete all as specified and directed.

M&L rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates Fe-290 (Gde E-165) complete all as specified and directed.

Dee Kay EnterPrises (BID ID -3362940)

manoj and company (BID ID -3363256)