Solar Powered pressurized irrigation infrastructure in overflowing village pond Jalmana Baba Subudin pond Distt. Karnal

Amount

Works Details

Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 1 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. HSR item No 4.33

Brick work with common burnt clay non-modular bricks of class designation 10.5 in foundation and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand) HSR item No 7.21.1

12 mm cement plaster of mix 1 :4 (1 cement: 4 fine sand) HSR Item No 11.5.3

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1:3:6 (1 Cement : 3 coarse and (zone-Ill) : 6 graded cum stone aggregate 20 mm nominal size) HSR Item No 6.1.4

Providing and fixing of three phase 50Hz ±3% rated motor, frequency 415V ± 3% rated motor voltage, with constant motor flux control, (Submersible motors shall conform to all the requirements of IS 9283) Solar A.C. Agricultural Pumps alongwith Universal Solar Pump Controller (USPC) all external part of motor used in open well submersible pump having casing of Alloy steel confirming to IS 3444 including all PVC insulated polymer sheathed 3 core flat type cabling in conduit, required from solar plant to solar pump through control room required to connect, including cost of and as per IS code 14220-2018 including third party inspection.Average discharge 13 LPS / Head 52 meter / minimum / minimum outpurating of 15 KW. Dualy installed on the suitable foundation. Actual pump set's parameters will be finalized after approval of design and drawing. Solar Pumping Sets should be of the make: KSB / Shakti/ Kirloskar /CRI/Lubi/ Crompton/ WPIL, (NS Item) @ Rs 11002.53/- per HP Quantities are total sum of varrious pumps capacity in HP may varry as per design requirement for site. ((174708*1.12/20)+(163063*1.12/15)+(123310*1.12/12.5))/3 N.S. Item

Providing, laying, aligning, and jointing with uPVC heavy body solvent at all level/ depths ISI marked PVC pipe of pressure as per design for raw water supply as per IS 4985 (amended up to date) in trenches in complete, including cost of all Specials, labour, and commissioning as per Technical Specifications and approved make as per direction of Engineer. (Make Duraline,Reliance, jain Irrigation, Nimbus, Finolex, Hasti, or equivalent) (Rate analysed with rate approved by worthy Administrator) a) PVC 4 Kg/Cm2, 110mm dia Pipe

Supply and installation of filters, Hydro cyclone/ Sand separator 40 cum/hr (hot-dip galvanized), Flange Connection with GI fittings, with flush valve, SS clamp, thread shall comply with IS 554, O'ring, with SS lock pin and collector tank as per IS 14743 as per latest amendment with all accessories (HSR item No 26.73.9)

Supply and installation of filters, Media filter 40 cum/hr, with back wash and bypass assembly made in mild steel body as per IS 14606 as per latest amendment with all accessories and shall be provided with measuring points at inlet & outlet for pressure measurement and with backup strainer filter and all flanges should be of steel pipe confirming to IS 6392 (HSR item No 26.73.2)

Supply and installation of Strainer filter 50 cum/hr, with flush valve size 38mm inlet with disc clean element strong precision engineered and radially grooved disc to provide three dimensional filter,strainer element shall be made of stainless steel as per IS 12785 with latest ammendment with all accessories. Housing made of mild steel shall be hot dip galvanized as per IS 4736 (HSR item No 26.73.6)

Providing & fixing Tank Type (Make of Metal) Fertilizer and Chemical Injector System confirming to IS 14483 (Part 3) of 2018 for demonstration & guiding the farmers regarding fertilization & chemicalisation of system. (rates include ventury with manifold 1.0"=1300 and 60 liter fertilizer tank= 4400 ) rate approved by Worthy Administrator

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Horizontal directional drilling with micro tunnelling methods, for pipe laying under pucca rasta /road crossing (N.S.Item)

Providing and lowering of HDPE floater manufactured with 225 mm dia PE pipe having PE-80 and PN-10 to float the submersible open well pump/motor (NS item)

Galvanizes steel chain link both end twisted fence fabric having opening size 7.5x7.5 cm & 3.15 mm dia wire, 2.2 meter height of mesh, with 2.8 meter ht of MS Angle 50x50x5 mm supports fixing at spacing of 3 meter centre to centre, supports with MS Flat 35x5 mm. Fencing supported with MS Angle 35x35x5 at top and bottom. The M.S Angle supports shall be anchored in cement concrete (1:3:6) blocks 45x45x60 cm additional razor barbed wire fencing shall be provided at the top of mesh, fencing including gate @ Rs 2000/- per meter (N.S.Item)

Supply Installation testing commissioning of Solar Photovoltaic Stand alone Plant conforming to MNRE specifications as amended, consisting of Mono Crystalline silicon solar cells, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength. Including lightning and surge voltage protection, Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required, built in metering system to moniter plant performence (Amp-meter, Volt-meter, Frequency meter, Energy meter, Watt-meter, and other instrument/equipment as required), Anti-Theft Screw Note:- PV modules used must qualify to the latest edition of IEC PV module qualification test or equivalent BIS standards Mono Crystalline Silicon Solar Cell Modules IEC 61215/IS14286. In addition, the modules must conform to IEC 61730 Part-1- requirements for construction & Part 2 – requirements for testing, for safety qualification or quivalent IS and be mounted on fixed Aluminium/GI structure of adequate strength and design as per IEC/IS specification. Including field-based electroluminescence (EL) study be performed after receiving the modules at site and after installation. Module mounting structure (MMS) design and drawing shall be duly vetted from government institute Including third party inspection Actual parameters/capacity will be finalized after approval of design and drawing. (N.S. Item)

Providing and fixing 12 Watt LED Street Lighting of 75 watt solar panel, 12.8 volt 30 Ah Lithium Ferro Phosphate battery, 12 Watt White LED Luminaire and Pole of 5 Meter above ground level with dusk to dawn operation {first 4 hours full light Systemding, fixing and testing of Solar light including battery: min. 24 lux) , rest of the time at lower light (50% Min. 12 lux) level} & 3 days or minimum 36 operating hours autonomy or as per direction of engineer-in-charge

Hydrant assembly for Nakka in fields, Rates are including rates of Tee, riser pipe, butterfly valve, Flange and labour for fixing butter fly valve should be as per IS 13095-2020 (Rates are as per analysis including HSR item 25.3.6)

Supply and installation of 50mm i/d hydraulic pressure relief valve of polemeride with accessories for pressure regulation of irrigation system as per BIS standard. Including all fittings/accesories required. (New HSR Item no 26.73.10)

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) 50mm dia Rates Including Service shaddel, ASTM Pipe, Coupler and ARV ( to be fixed in field) @ 250 meter spacing Including cost of isolator. (HSR item No 22.185.1)

Providing, fixing,testing & commissioning of pressure gauge 2" dial with Glycerin filled to be fixed before and after filtration unit

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) 80 mm dia. (HSR Item No 22.185.2)

White washing with lime to give an even shade New work (three coats) (HSR item No11.61.1)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 80 mm nominal bore (HSR Item no 22.98.7)

Supply and jointing of 110 mm 6kg/cm^2 HDPE pipe (for jointing floater all filters prv ,etc ) 506.11+18%=597.21

Providing fixing of Header Assembly/Manifold 3" to connenct the filtration unit (loose) (Rate app. By worthy Administrator)

Providing, lowering, laying in trenches, aligning, fixing in position and jointing at all level/depths cast iron (Cl) standard specials plain /flanged/ socketed confirming to IS13382 with rubber ring, nut bolts and rubber sheet such as tees, bends, tapers, caps etc. complete including all material, labour, testing and commissioning along with pipe line as per Technical Specifications and as per direction of Engineer. HSR Item No 20.69.1 Up to 300mm dia (50 KG per pumping Unit)

Providing & fixing cast iron double flanged swing check type reflux (non return) valves PN-I.6 marked with IS : 5312 including nuts & bolts marked with IS: 1363. rubber sheet marked with IS: 638 etc. carriage loading, unloading, stacking, handling, re-handling etc. complete in all respect to the satisfaction of Engineer-in-charge. (HSR item No.20.11.3)

Providing and laying 50 mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over (BIS 15658:2021) and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. ( HSR item No 10.75)

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil (HSR item no 4.4.1)

Construction of 6'x6' regulation hut constructed with 9" thick brick masonary inner side covered with 1.25 mm thick class-1 GI corrugated sheets (with 750 gm Zinc coating per sqm on its both sides) provided with proper door and windows as per approved design and drawing inner size 6'x6' Av. Height 8' covered with Precoated G.I. Corrugated sheet

Complet operation & Maintenance and watch & ward of the project for one year including operation of pump, pipe line, accessories, electromechanical, solar plants complet in all respect of pump house, pipe line and accessories, electromechanical, solar plant etc complete in all respect for one year @ Rs 6000/- per month

Supply and jointing three core submersible flat cables of approved make with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors /fountain lights etc with voltage grade 1100 volts marked with IS:694, 1990 including cost of jointing, materials as well as carriage, loading, unloading etc. complete in all respect up to the entire satisfaction of Engineer- in-Charge. Submersible Copper Cable 3 Core 16 sqmm HSR Item No 24.5.1.6

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-all work below plointh level and upto floor IV level : 1:4:8 ( 1 Cement : 4 coarse sand zone III : 8 graded cum stone aggregate 40mm nominal size) (New HSR Item No 6.1.6)

Empty Cement Bag for protecting side slope of earth filled in pond for solar panels (New HSR Item No B0976) considering volume of one bag 0.03472 cum and 0.01736 cum for concrete

The Safal Coop L/c Society Ltd.

the pal cooperative labour and construction limited karnal