Construction of Balance work of PG Computer Block in Govt. PG Degree College at Rajouri (complete job).

Amount

A. Building Part

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (Exceeding 30cm in depth, 1.5mtr in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.50 m, disposed earth to be levelled and neatly dressed in All Kind of Soil @ 70%

Ordinary rock @ 30%

Earth work in excavation by mechanical means (Hydraulic excavator) in foundation trenches, drains, pipes and cables etc. (not exceeding 1.5mtr in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5mtr including getting out excavated soil and disposal of surplus soil as directed, within a lead of 50 mtr. All Kind of Soil @ 70%

Ordinary rock @ 30%

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (Not exceeding 1.5 mtr in width) and for shafts, wells, cesspits and the like not exceeding 10sqm on plan, depth upto 1.5mtr. including disposal of excavated earth upto 1 mtr from cutting edge, disposed earth is to be levelled and neatly dressed in: all kinds of soil.

Extra for every additional lead of 25mtr beyond 1 mtr upto 250 mtrs. and deposit to a level of 1.5mtr for quantity vide item no 3

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level 1:4:8 (1 cement: 4 coarse sand :8 graded stone aggregate 40mm nominal size)Crushed Aggregate

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level 1:5:10 (1 cement: 5 coarse sand :10 graded brick aggregate 40mm nominal size upto floor V level)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring and shuttering- All work upto plinth level 1:1.5:3(1 cement:1. 5 coarse sand :3 graded stone aggregate 20mm nominal size)Crushed Aggregate

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts ans sturts, etc. upto floor five level excluding cost of Centring, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20mm nominal size)Crushed Aggregate

Providing and laying Reinforced Cement Concrete 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) in suspended floors, balconies, landings and staircase having upto 15° slope. excluding cost of centering and shuttering , all work upto floor V level,Crushed Aggregate

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level 1:3:6 (1 cement: 3 coarse sand :6 graded stone aggregate 20mm nominal size) Crushed Aggregate

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. TMT bars

Centring and shuttering including strutting, propping etc. and removal of form for·

Foundations: footings, bases of columns etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders,bressumers and centilevers.

Edges of slabs and breaks in floors and walls. Under 20 cm wide

Columns, Pillars, Piers, Abutments, Posts and Struts

Walls any thickness including attached pilasters, buttresses plinth and

Weather shade. Chajjas, corbels etc., including edges.

Stairs, (excluding landings) except spiralstaircases.

Providing and laying damped proof course 40 mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand :4 graded stone aggregate 12.5mm nominal size) crushed

Brick work with common burnt clay F.P.S.(non-modualar)bricks of class designation 75 in foundation and plinth in Cement mortar 1 :6 ( 1 cement : 6 coarse sand)

Extra for brick work in superstructure above plinth level upto floor V level. (By manual means)

Half brick masonry with bricks of class designation 75 in foundations and plinth in Cement mortar 1 :4 ( 1 cement : 4 coarse sand)

Extra for half Brick masonry in superstructure above plinth level upto floor V level.

Providing and laying hand packed stone soling in foundation, under floors etc. including ramming, watering and consolidation complete. Cost and carriage of all materials involved utpo site of work complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class teak wood

Providing and fixing lSI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including lSI marked M.S. pressed bright finished butt hinges with necessary screws of required size

Providing and fixing 35 mm glazed shutters for windows and clerestory windows using 10 kg/sqm (4mm thick) float Rate for thickness of glass panes including lSI marked M.S. pressed butt· hinges bright finished of required size with necessary screws.Second class teak wood

Providing and fixing 35 mm thick wire gauze shutters using galvanised M.S. wire gauze of average width for aperture 1.4 mm in both directoin with wire of dia. 0.63 mm for doors, windows and clerestory windows with hinges and necessary screws lSI marked M.S. pressed bright finished butt hinges with necessary screws of required size.Second class teak wood

Strctural steel work in single section fixed with connecting plate including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete.Fixed to openings/wooden frames with raw/plugs screws etc.

Providing and fixing glazing in fixed ventilator of door frames with floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg/sqm)

12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) with making of groove between brick work and RCC

15mm Cement plaster of mix: 1 : 6( 1 cement : 6 fine sand) with making of groove between brick work and RCC

15mm Cement plaster of mix: 1 : 4( 1 cement : 4 fine sand) with making of groove between brick work and RCC

20 mm Cement plaster of mix: 1 : 6( 1 cement : 6 coarse sand) with making of groove between brick work and RCC

20 mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 coarse sand) with making of groove between brick work and RCC

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. Layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m.

Disposal of excavated material beyond 50 mtr and within 10 Km

Supplying and filling in plinth with fine sand under floors including, watering, ramming consolidating and dressing complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to lS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 60x60cm

Providing and fixing Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 13755 of NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in colour such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of Cement Mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing antiskid floor tiles for ramp 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 13755 of NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in colour such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of Cement Mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying/ fixing Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 13755 of KAJARIA, SOMANY or equivalent make as approved by Project Authority and Site incharge in colour shades except White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of Cement Mortar 1: 4 (1 cement: 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing 1st quality ceramic glazed tiles conforming to IS :·13753 of minimum thickness 5 mm of approved make like NITCO, ORIENT, SOMANY KAJARIA, or equivalent make in all colour, shades except begundy, bottle green, black of any size as approved by Eningeering in Charge in skirting, risers of steps and dados over 12 mm thick bed of Cement Mortar 1:3 ( 1 cement: 3 coarse sand) and jointing wtih grey cement slurry@ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing Granite Jet Black/Chilly Red gang saw cut mirror polished (pre moulded and pre Polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels 16mm thick

Providing and fixing Granite Jet Black/Chilly Red gang saw cut mirror polished (pre moulded and pre Polished), machine cut for stair steps and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels 16mm thick

Providing and fixing Granite Jet Black/Chilly Red gang saw cut mirror polished (pre moulded and pre Polished), machine cut for floors of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels 16mm thick

Extra for providing opening of required size and shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble I stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Extra for providing edge moulding to 18 mm thick marble stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite work

25 mm Thick Kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1:4 (1 cement: 4 coarse sand) :

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanised with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastner 12.5 mm diax40mm long with 6 mm dia bolts, othP.r flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with G. I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick buttom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.l.intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G. I. wire at every junction, including fixing perimeter channels 0.5mm thick 7mm high having flanges of20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at450 mm centre to centre, with 25mm long drive-all screws@ 230 mm interval ,including fixing of gypsum board to celing section and perimeter channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers' specification and also including the cost of making openings for light fittings, grills diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with: 2.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-Part 1

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement@ 0.488 kg/sqm mixed with with water proofing cement compound @ 0.253kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound@ 0.126 kg/sqm . This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes prepartation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonary with polymer mixed slurry.

Providing and laying integral cement based water proofing treatment including prepration of surfaces as required for treatment of roofs, balconies, terracies etc consisting of following operations. a) applying a slurry coat of neat cement using 2.75kg/ sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC Slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/ Brick Bats 25mm to 115mm size with 50% of Cement mortar 1:5 (1 Cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 Cement: 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300mm height including rounding of Junctions of walls and slabs) c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 andapproved by Engineer-in-charge. d) finishing the surface with 20mm thick jointless cement mortar of mix 1 :4(1 cement: 4 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved byEngineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finially finishing the surface with trowel with neat cement slurrv and making pattern of 300x300mm/sq 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer-in-charge. With average thickness of 120mm and minimum thickness at khurra as 65 mm.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design : In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outletcomplete.

Providing and fixing 1 mm thick M.S. steel door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer Using M.S. angles 40x40x6mm for diagonal braces

Making plinth protection 50 mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggreagate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. Crushed.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinable cement primer of approved brand and manufacture on wall surface Water thinable Cement primer (Interior)

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Conpound) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour Two coats

Applying one coat of water thinable cement primer of approved brand and manufacture on wall surface Water thinable Cement primer (Exterior)

Finishing walls with acrylic smooth exterior paint of required shade on New work (two or more coats applied @ 1.67 litre/1 0 sqm over and including base Coat of water proofing cement paint applied @ 2.20kg/1 Osqm)

Applying priming coat: with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade on wood work. Two or more coats on new work

Painting with ready mixed synthetic enamel paint of approved brand and manufacture in all shades to give an even shade New steel work (two or more coats)

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and em beddings in cement concrete block 30x10x15 cm 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size )

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc.including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete,i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standardtubular sections/appropriate Z.sections and othersections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene .. gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P. brass I stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in- Charge (glazing, panelling and dash fasteners to be paid for separatelyPowder coated aluminium (minimum thickness kg 453.15 of powder coated 50 microns)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber I neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.) With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg I sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo em,possed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot" and single piece M.S. sheet outer box with slide plate etc. complet~ as per the direction of Engineer-in- Charge With Stainless Steel cover plate minimum 1.25 mm thickness

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 minimum anodic coating of Grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/stainless steel screws@ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (onlyweight of grill to be measured for payment)

Providing and fixing Galavanised wire mesh of average width of aperture 1.4 mm and nominal dia. of wire 0.63 mm in in aluminium door, window, ventilator shutters etc. with EPDM rubber I neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.)

Providing and fixing lSI marked aluminium butt hinges lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete 75x63x3.2 mm

Providing and fixing lSI marked aluminium butt hinges lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete 100x63x3.2 mm

Providing and fixing aluminium tower bolts lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete 150x10 mm

Providing and fixing aluminium handles lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete 125 mm

Providing & fixing aluminium sliding door Bolts ISI marked anodized (annodic coating not less than grade AC 10 as per IS: 1368) transparent or dyed to required colour or shade with necessary screw etc. 300x16mm

Providing & fixing aluminium tower Bolts ISI marked anodized (annodic coating not less than grade AC 10 as per IS: 1368) transparent or dyed to required colour or shade with necessary screw etc. 200x10mm

Providing & fixing aluminium tower Bolts ISI marked anodized (annodic coating not less than grade AC 10 as per IS: 1368) transparent or dyed to required colour or shade with necessary screw etc. 300x10mm

Providing & fixing aluminium handles ISI marked anodized (annodic coating not less than grade AC 10 as per IS: 1368) transparent or dyed to required colour or shade with necessary screw etc. 200 mm

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete of make godrej, link or equivalent as approved by the engineer -in-incharege.

Carriage of below 40mm from source to site of construction average lead 20 kms. including loading and unloading and stacking at site complete

Carriage of 40mm aggregates & above average lead 20 kms. including loading and unloading and stacking at site complete

Carriage of Nallah sand from source to site of construction average lead 120 kms. including loading and unloading and stacking at site complete

Carriage of Crusher sand from source to site of construction average lead 20 kms. including loading and unloading and stacking at site complete

Carriage of Brick Bat for average distance of 140 KM by MT including loading and unloading and stacking at site complete

Carriage of Brick for average distance of 140 KM by MT including loading and unloading and stacking at site complete

Carriage of soling stone for average distance of 10 KM by MT including loading and unloading and stacking at site complete

B.Plumbing/Sanitary

Providing and fixing white vitreous china pedestal type water closet (European type W.C . .pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever requied W.C. pan with lSI marked white solid plastic seat and lid of make Hindware/Cera/Jaquar or as approved by site incharge

Providing and fixing water closet squatting pan ( Indiantype W.C. pan) with 100 mm sand cast Iron P or Strap,10 litre low level P.V. C. flushing cistern including flushpipe (of approved make) "manually contro(led device(handle lever) conforming to IS:7231, with all fittings andfixtures complete, including cutting and making goodthe walls and floors wherever required Orissa pattern white vitreous china W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing ONE PIECE white vitreous china water closet (European type W.C . .pan) seat 300mm distance from wall and 10 litre capacity white vitreous china flushing cistern conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever requied W.C. pan with lSI marked white solid plastic seat cover of make Hindware/Cera/Jaquar or as approved by site incharge

Providing and fixing wash basin with C. I./M.S. brackets,15mm C.P. centre hole mixture, 32 mm C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China wash basin size 660x460 mm of make Hindware/Cera/Jaquar or as approved by site incharge

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings of make Hindware/Cera/Jaquar or as approved by site incharge

Providing and fixing Salem Stainless Steel A lSI 304 (18/8) kitchen sink including waste coupling as per I.S. 13983 with C.l. brackets and stainless steel plug 40 mm including painting of fitting sand brackets, cutting and making good the walls wherever required 510x1040mm bowl depth 250mm

Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fitting complete. Flexible pipe 32 mm dia

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265 mm sizes respectively with automatic flushing cistern with C. I./M.S. brackets standard size of G. I. flush pipe and C.P. brass spreaders with brass unions and G. I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required of make Hindware/Cera/Jaquar or as approved by site incharge Range of two urinal basins with 5 litre P.V.C white automatic flushing cistern of approved quality

Providing and fixing 100 mm CP grating for gully, floor or Nahani trap.

Providing and fixing mirror of superior glass( of approved quality) and of required shape and size with plastic . moulded frame of approved make and shade with 6 mm thick hard Rectangular shape 453x357 mm

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C. P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete

Providing and fixing toilet paper holder C.P. brass

Providing and fixing PVC pipes with necessary stays / clamps with fasteners of following dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent

160 mm dia

110 mm dia

75 mm dia

Providing and fixing PVC door bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete:

160 mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent

100 mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent

75 mm dia. working pressure 4kg/cm2 of make Supreme, finolex or equivalent

Providing and fixing PVC plain bend of required degree:

160 mm dia. working pressure 4kg/cm2 of make Supreme, finolex or equivalent

100 mm dia. working pressure 4kg/cm2 of make Supreme, finolex or equivalent

75 mm dia. working pressure 4kg/cm2 of make Supreme, finolex or equivalent

Providing and fixing PVC door Tee with PVC acess door, insertion rubber washer 3 mm thick, bolts and nuts complete.

100x100x100mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent

75x75x75mm dia working pressure 4kg/cm2

Providing and fixing PVC reducer tee with PVC acess door, insertion rubber washer 3 mm thick, bolts and nuts complete.

100x100x75mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent

Providing and fixing PVC Plain reducer tee insertion rubber washer 3 mm thick, bolts and nuts complete.

100x100x75mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent

Providing and fixing PVC offsets working pressure 4kg/cm2 of make Supreme, finolex or equivalent

75 mm PVC off sets

110 mm PVC off sets

160 mm PVC off sets

Providing and fixing PVC collar:

110mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent

75mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent

160mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent

Providing and fixing PVC P/S/F trap of different dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent complete, including cost of cutting and making good the walls and floors:

Cutting chases in brick masonry walls for following diameter PVC pipes and making good the same with cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 12.5mm nominal size) 1:4 ( 1 cement: 4 coarse sand)

100mm dia.

75mm dia.

Providing & fixing PVC Cowl of make Supreme, finolex or equivalent

Providing and fixing Soap dish (C.P. brass) with bracket

Providing and fixing towel ring (C.P. brass)

Providing and fixing towel rail 600mm long (C.P. brass)

Providing and fixing G.l. pipes complete with G.l. fittings and clamps, including cutting and making good the walls etc. (Internal work) of make Jindal/Surya Prakash of medium class or as approved by site incharge

15 mm dia. nominal bore (medium)

20 mm dia. nominal bore (medium)

25 mm dia. nominal bore (medium)

32 mm dia. nominal bore (medium)

40mm dia. nominal bore (medium)

Providing and fixing G.l. pipes complete with G.l. fittings including trenching and refilling etc. (external work) of make Jindal/Surya Prakash of medium class or as approved by site incharge

25 mm dia. nominal bore

Making connection of G.l. distribution branch with G.l. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete

25 to 32 mm nominal bore

Providing & fixing Brass ball valve of approved quality conforming to IS : 8931 of 15mm nominal bore of make DRP or as approved by site incharge

Providing & fixing Brass ball valve of approved quality conforming to IS : 8931 of 25mm nominal bore of make DRP or as approved by site incharge

Providing & fixing Brass ball valve of approved quality conforming to IS : 8931 of 32mm nominal bore of make DRP or as approved by site incharge

Providing and fixing C.P. brass bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 15 mm nominal bore of make hindware/cera/jaquar or as approved by site incharge

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 15 mm nominal bore of make hindware/cera/jaquar or as approved by site incharge

Providing and fixing C.P. Jet with connection pipe

Providing and fixing C.P. brass angle valve for basin mixer and gyser points _of approved make conforming to IS : 8931 15 mm nominal bore of make hindware/cera/jaquar or as approved by site incharge

Providing and fixing C.P. brass angle valve for basin mixer and gyser points _of approved make conforming to IS : 8931 15 mm nominal bore of make hindware/cera/jaquar or as approved by site incharge

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) R.C.C. top slab with 1 :2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finsihed with a floating coat of neat cement complete as per standard design

Inside size 90x80 cm and 45 cm deep including C.l. cover with frame (light duty) 455x610 mm. internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) With F.P.S. bricks with class designation 75 & with Crushed stone aggregate

Providing and fixing G.l. Union in G.l. pipe including cutting and threading the pipe and making long screws etc. complete (new work)

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid lSI license].

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G. I. pipe etc.

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 gradedstone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement: 3 coarse sand 6 graded stone aggregate 20 mm nominal size) including disposal of malba.

Cutting holes up to 30x30 em in walls including making good the same With common burnt clay F.P.S. (non modular) bricks

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround pvc pipes including bed concrete as per standard design

100 mm diameter S.W. pipe (a) Crushed

150 mm diameter S.W. pipe (a) Crushed

Providing installation and testing of geysor of approved quality and manufacture venus/Bajaj or equivalent all complete

35 litre capacity

Making soak pit 2.5 m diameter 3.0 metre deep with 45x45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Providing & Installation of two Nos 2HP three phase pump of make Crompton with electirical connection complete

C. Electrification Work

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in existing surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. ( Group C)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in existing surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. ( Group B)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 2.5 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. ( 1 run of cable)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Telephone socket outlet

Bell push

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

1 or 2 Module

3 Module

4 Module

6 Module

8 Module

Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Single pole and neutral

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Supplying and fixing of following rating 240 Volts "C" Series miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning. (Make as per annexure enclosed).

Triple Pole and Neutral 63/40 Amp.

Supplying and fixing of surface 15 watt LED type. Ceiling light including connections etc as required.

Supplying and fixing of 10 watt LED batten fitting for Mirror Light including connections etc. as required.

Supplying and fixing of surface mounted 20/22 watt batten LED tube fiiting 4 feet long including connections etc as required.

Supplying and fixing of surface mounted bracket light /bulk head fitting suitable for one no 9 watt LED Bulb including connections etc as required. and complete with 9 watt LED Bulbs.

Supplying & fixing 50W LED Flood light fitting complete with connection,testing etc

Supplying and fixing of following electrical items suitable for operating on 240/230Volts AC, 50 Hz including connections etc. as required.

Ceiling fan 1200 mm sweep (5 star Rating)

Wall Fan 400 mm sweep

Exhaust fan 300 mm size

Exhaust fan 380 mm size Heavy Duty.

2'x2' LED Panel 36/40 W

2-way AC Box

Providing and Fixing of LED 35/40w post top Light with pole

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Providing and Fixing of 8way DD (4+24)Distribution Board

Providing and Fixing of 4way DD (4+12)Distribution Board

Providing and fixing of L.T.Panel after fabrication of panel with 14 CRCA Sheet,hinged lockable door,LED Indicator Lamp,Bus Bar,powder coated alog with following accessories:- incoming-200A 4P 50K MCCB-1NO. out going-,63A 4P 25K MCCB-10 NO., 63ATPN MCB-1N0.,63ASPN MCB-1N0.alongwith Change Over Switch 200 A 4P..1 NO.Complete with all lift and leads,Testing ,Commissioning etc.MAKE:MCCB/MCB-LEGRAND/ABB/ L&T-(Emergency L.T.Panel)

Providing and fixing of L.T.Panel after fabrication of panel with 14 CRCA Sheet,hinged lockable door,LED Indicator Lamp,Bus Bar,powder coated alog with following accessories:- incoming-630A 4P 50K MCCB-1NO., out going-,100 A 25K 4P MCCB-10NOS& 250 A 4P MCCB 50K-1NO., 63ATPN MCB-1N0.,63ASPN MCB-1N0.Complete with all lift and leads,Testing ,Commissioning etc.MAKE:MCCB/MCB-L&T-(Main Normal L.T.Panel)

providing and Laying of 400Sq.mm 3.5 core Pvc Insulated AL.Cable along with reqd.size of AL.Glands and also laying of cable after comlete digging process with the cost of Pvc Pipe of 160MM dia of 6KG.Pressure,Including excvation work, Concreating,Manhole etc.

Providing and Laying 185Sqmm 3.5 core Pvc Insulated AL.Cable along with reqd.size of AL.Glands.

Electromechanics Engineers And Contractors

SATVIR GUPTA ENGINEERS AND CONTRACTORS

M/S QAZI MUSHTAQ SON