MAINT/REPAIR OF JOINERY, PLUMBING, DAY TO DAY COMPLAINTS AND OTHER ESSENTIAL B/R WORKS INCLUDING PERIODICAL SERVICES AT 274 TRANSIT CAMP KHANPUR UNDER AGE B/R-I OF GE (SOUTH) DELHI CANTT-10

Amount

Attending complaint for petty repair to leaking water in bib tap, pillar tap, stop cock, angle valve, flushing cistern, WHB, Sink, wall mixer etc. of any description any size by changing the washers(s)/jumper(s) etc, by adjusting/replacing the washer(s) and adjustment of lever required for making the flushing cistern functional, by tighting the leaking waste pipe of WHB/Sink and providing 'M' seal to stop leakage as required. Removal of air lock/blockage of water in GI water tubing and cleaning the pipe or fittings etc. including replacement of major defective item if required, complete all as specified and directed by Engineer-in-charge. Note 1 :- The contractor shall make all arrangement for attending the different types of complaints on every day basis.Any major item required to be replaced with new one, to make the system functional shall be measured and paid for seprately as " S & F" under respective applicable item of this schedule. Old retrived item (s) as considered in 'Schedule of Credit' shall become property of the contractor. 2. Contractor shall provide minimum one plumber for VRC including all necessary T & P on all working days from 9AM to 5 PM .Additional workers can be engaged if nature of work required to be completed with in fixed time as desired by GE . Rate shall be quoted accordingly . Keeping in mind above said provisions. 3. Where material provided shall be paid as " S&F underrespective item of Sch. 'A' the payment of complaint under this item shall not be paid. 4. Proper records (date wise) of complaints received & rectified by the contractor and attendance register of trademen shall be maintained by Engineer-in-charge.

S & F in repair chromium plated bib tap long body with flange cast copper alloy with crutch or butterfly handle, screwed for iron pipe, complete all as specified and as directed.

S & F in repair Fancy type bib tap ISI marked cast copper alloy with fancy type screwed down high pressure and screwed for iron pipe of 15mm bore complete all as specified and as directed.

S & F in repair bib tap standard 15 mm dia of PTMT any colour for iron pipe and fixed (Minimum weight 90 gms) complete all as specified and as directed.

S & F in repair Chromium plated Pillar tap 15 mm bore cast copper alloy with capstan heads chromium plated screwed down high pressure screwed in iron pipe complete all as specified and as directed.

S&F in repairs stop cock cast copper alloy, screw down high pressure with crutch or butterfly handle screwed both ends suitable for iron pipe of 15mm bore complete all as specified and as directed.

S & F in repair PVC connection 15 mm dia 45 cm long with 2 Nos PVC check nuts with washer complete all as specified and as directed.

S & F in repair chromium plated Stop valve/angle valves cast copper alloy, screwed down both, high pressure, with crutch or butterfly handle, screwed both end fixed, complete all as specified and as directed.

S & F in repair chromium plated brass overhead shower with arm 195 mm with flange with swivel joints, any size, including fixing to steel pipe or union for 15mm bore pipe complete all as specified and as directed.

S & F in repair brass jumper washer, brass head, face and spindle for bib cock/pillar cock/stop cock 15 mm bore any type complete all as specified and as directed.

S & F in repair 15mm dia stop valve concealed type cast copper alloy, screwed down, high pressure chromium plated with long shank including making good dismantled portion complete all as specified and as directed.

S & F in repair 32 mm to 40mm dia PVC waste pipe for WHB & sink, 60 cm long with union complete all as specified and as directed.

S & F in repair waste fittings brass chromium plated 32 mm dia for wash hand basin complete all as specified and as directed.

S & F in repair waste fittings brass chromium plated 40 mm dia for stainless steel sink complete all as specified and as directed.

S & F in repair gun metal globe or gate valve, with iron wheel head screwed both ends and for iron pipes and fixed for bore of pipe 15 mm complete all as specified and as directed.

S & F in repair gun metal globe or gate valve, with iron wheel head screwed both ends and for iron pipes and fixed for bore of pipe 20 mm complete all as specified and as directed.

S & F in repair small fittings galvanised iron 'medium grade' such as socket, elbow, nipple of any length upto 150mm long, Tee, union etc for 15 mm bore pipe (ISI marked) complete all as specified and as directed. (This item will not be measured against item No.54 here in after).

S & F in repair small fittings galvanised iron 'medium grade' such as socket, elbow, nipple of any length upto 150mm long, Tee, union etc for 20 mm bore pipe (ISI marked) complete all as specified and as directed. (This item will not be measured against item No.55 here in after).

S & F in repair small fittings galvanised iron 'medium grade' such as socket, elbow, nipple of any length upto 150mm long, Tee, union etc for 50 mm bore pipe (ISI marked) complete all as specified and as directed. (This item will not be measured against item No.56 here in after).

S & F in repair CI bracket of exiting size, for WHB or Kitchen Sink etc including cutting, necessary fitments for pinning in brackets complete all as specified and as directed.

S & F in repair PVC syphone with handle complete for low level flushing cistern complete all as specified and as directed.

S & F in repair PVC handle heavy duty, for low level flushing cistern complete all as specified and as directed.

S & F in repair 10 ltrs capacity PVC Low level flushing cistern including PVC syphon and float valve with float, PVC long bend for out let connection of cistern with WC complete fixing and connecting bend with WC complete all as specified and as directed.

S & F in repair PVC float valve for cistern tank complete all as specified and as directed.

S & F in repair plastic water closet seat cover (for Anglo Indian/EWC ) white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium anodised hinging device complete all as specified and as directed.

S & F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

S & F in repair CP grating 127 mm dia with/without hole round, fixed on floor / nahani trap, fixed with cement mortar(1:3) complete all as specified and as directed.

S & F in repair chromium plated Jet for WC with 1.00 m long PVC pipe including necessary GI fitting as required like toe, nipple etc complete all as specified and as directed.

S & F in repair soap dish Chromium plated brass fancy type complete all as specified and as directed.

S & F in repair, Toilet paper holder Chromium plated brass fancy type complete all as specified and as directed.

S & F in repair, Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and as directed.

S & F in repair, CP towel rail 60 cm long complete all as specified and as directed.

S & F in repair glass Shelf Corner with frame Chromium plated brass fancy type complete all as specified and as directed.

S & F in repair HDPE PVC lid (cover) for 1000 to 2000 Ltrs capacity PVC tank complete all as specified and as directed.

S & F in repair HDPE PVC lid (cover) for 500 Ltrs capacity PVC tank black/White complete all as specified and as directed.

Attending complaint for petty repair to easing of Doors/Window/Cup Board shutters by tightening of hinges / handles / Al-drop bolt / tower bolt / knobs, hasp and stapple etc of any size / any number of panels for easy closing / opening or changing the position of hinges, adjustments of tower bolts,sliding bolts, replacement of looking mirror etc complete including replacement of major defective item if required, complete all as specified and directed by Engineer-in-charge. Note 1 :- The contractor shall make all arrangement for attending the different types of complaints on every day basis.Any major item required to be replaced with new one, to make the system functional shall be measured and paid for seprately as " S & F" under respective applicable item of this schedule. Old retrived item (s) as considered in 'Schedule of Credit' shall become property of the contractor. 2. Contractor shall provide minimum one Carpenter for VRC including all necessary T & P on all working days from 9AM to 5 PM .Additional workers can be engaged if nature of work required to be completed with in fixed time as desired by GE . Rate shall be quoted accordingly . Keeping in mind above said provisions. 3. Where material provided shall be paid as " S&F underrespective item of Sch. 'A' the payment of complaint under this item shall not be paid. 4. Proper records (date wise) of complaints received & rectified by the contractor and attendance register of trademen shall be maintained by Engineer-in-Charge.

S & F in repair 9 mm Plywood, grade BWR, type BB,not exceeding 1.50 sqm fixed with nail / screw to timber frame work complete all as specified and as directed.

S & F in repair magic eye for panelled/flush shutter 35 mm thick complete all as specified and as directed.

S & F in repair CP Peg set of 06 hanging complete all as specified and as directed. Make:- As per sample available with GE office complete all as specified and as directed.

S & F in repair sliding door bolts 300 mm long clip type stove enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S & F in repair MS barrel tower bolt, stove enamelled black 200mm long complete all as specified and as directed.

S & F in repair 100 mm long MS butt hinges 'medium weight' cold rolled welded to steel frame work complete all as specified and as directed.

S & F in repair steel window handles(right & left) and peg stays etc as per sample complete all as specified..

S & F in repair 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

S & F in repair 125 mm mild steel pressed handle oval type, stove enamelled black complete all as specified and as directed.

S & F in repair 125 mm aluminium anodised handle cast type, complete all as specified and as directed.

Taking up or down GI steel water tubing 15mm bore and connections including cleaning complete all as specified and as directed.

Taking up or down GI steel water tubing 20mm bore and connections including cleaning complete all as specified and as directed.

Taking up or down GI steel water tubing 50mm bore and connections including cleaning complete all as specified and as directed.

Refixing the old GI steel water tubing and connection of 15 mm bore in new / old position with and including all fittings, to roofs,walls or ceiling complete all as specified and as directed.

Refixing the old GI steel water tubing and connection of 20 mm bore in new / old position with and including all fittings, to roofs,walls or ceiling complete all as specified and as directed.

Refixing the old GI steel water tubing and connection of 50 mm bore in new / old position with and including all fittings, to roofs,walls or ceiling complete all as specified and as directed.

S&F galvanised steel water tubing 15 mm bore 'medium grade' with and including all fittings and fixed to walls or laid in floors complete all as specified and as directed.

S&F galvanised steel water tubing 20mm bore 'medium grade' with and including all fittings and fixed to walls or laid in floors complete all as specified and as directed.

S&F galvanised steel water tubing 50mm bore 'medium grade' with and including all fittings and fixed to walls or laid in floors complete all as specified and as directed.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in repair for vitreous china wash hand basin flat back size 550x400 mm size white excluding taps waste chain and plug and porcelain stopper but including brackets and 32 mm dia waste fittings brass chromium plated with long screwed shanks and fly nuts, 32mm X 600 mm long PVC waste pipe complete flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

M&L for manual Sealing of traps,WCs (manually) with neat cement paste after removal of water from it, to prevent or make up the leakage including cementing in cement mortar (1:3) from inside and outside both & refixing grating, plasters etc complete all as specified and as directed.

S&F in repair vitreous china squatting pan (Orissa pattern white) long pan fixed size 580x440mm white with integral footrest with 100 mm bore Cast iron `P' or `S' trap complete (excluding flushing cistern and flush pipe) complete all as specified and as directed.

S&F in repairs viterous china wash down water closet pan Pedestal pattern (Anglo Indian WC) white incl 'P' or 'S' trap and making good the disturbed surface to match with the existing complete all as specified and as directed.

S&F in repairs 15 mm size brass chromium plated two way angle valves fancy type cast copper alloy, complete all as specified and as directed.

Taking down cast iron pipes including fittings by burning out lead joints etc to facilitate dismantling old serviceable fittings/pipes laid in trenches,floors or fixed to walls all as directed including earth work, demolition of PCC / Brick work complete all as specified, for the following sizes of pipes:-

100 mm bore of pipe.

75 mm bore of pipe.

S&F cast iron sand soil waste or vent pipes (ISI Marked), in any length with or without ears with joints in cement mortar (1:3), laid in trenches, floors or fixed to walls all as directed including making good to match with existing surfaces complete all as specified, for the following sizes of pipes:-

100 mm bore of pipe.

75 mm bore of pipe.

S&F cast iron branch pieces (ISI Marked), single (equal or unequal) ordinary of inverted spigot or socket type complete all as specified,for the following sizes of pipes:-

100 mm bore of pipe.

75 mm bore of pipe.

S&F cast iron bends (any radius) diminishing pieces or tapers (larger bore measured) complete all as specified, for the following sizes of pipes:-

100 mm bore of pipe.

75 mm bore of pipe.

S & F CI bends / branch pieces (any radius) for oval access doors complete all as specified for the following :-

100 mm bore of pipe.

75 mm bore of pipe.

M&L in repair, CI floor trap with grating including jointing to waste pipe in run lead, dia of outlet 75 mm including floor around to required depth and burning lead joints etc to facilitate dismantling old CI trap and making good complete all as specified.

Extra over cast iron pipe and fitting if lead joint are provided in lieu of cement joints complete all as specified,for the following sizes of pipes:-

100 mm bore of pipe.

75 mm bore of pipe.

S&F in repair, MS clamps for CI pipes 100 mm bore made out of 50 mm x 5 mm flat and 16 mm dia round bars, including bolts and nuts and securing to wall in PCC (1:2:4) and making good in cement mortar (1:3) complete all as specified.

Dismantling water tanks exceeding 500 litre but not exceeding 1000 litre and removal from site complete all as specified.

S&F rotational moulded polyethelene water storage tank 4 layer capacity 750 litres cylindrical vertical with closed top hoisted and fixed in position complete all as specified and as directed.

M&L for 10 mm thick rendering with readymix plaster (as per manufaturer's instruction) on faces of brick or concrete surfaces finished even and smooth surface wihtout using extra cement on wall of up to four stories bldgs including taking down cement plaster on brick walls, concrete surfaces, raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for 5 mm thick rendering with redymix plaster (as per manufaturer's instruction) on faces of brick or concrete surfaces finished even and smooth surface wihtout using extra cement on wall of up to four stories bldgs including taking down cement plaster on brick walls, concrete surfaces, raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for 15 mm thick rendering with redimix plaster (as per manufaturer's instruction) on faces of brick or concrete surfaces finished even and smooth surface wihtout using extra cement on wall of up to four stories bldgs including taking down cement plaster on brick walls, concrete surfaces, raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Demolition of cement concrete in ground floor and paving etc not exc 15 cm thick above or below ground level complete all as specified and as directed.

M&L for PCC (1:2:4) Type B-1 (using 20 mm graded stone aggregate), 40 mm thick as in floors etc finished even and smooth without using extra cement complete all as specified.

M&L for PCC (1:3:6) type C-2 (using 40 mm graded aggregate) 75 mm thick as in floor / plinth protection finished even and smooth without using extra cement complete all as specified and as directed.

M & L for preparing new plastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of interior primer, over & including a coat of wall care Putty complete all as specified and as directed.

M&L preparing new plastered or unplastered surfaces of wall and applying two coats of white wash on ceiling surface complete all as specified and as directed.

M&L for preparation of new plastered wall surfaces and applying two coats of cement base paint, white or tinted (colour and shade as per new colour scheme approved by GE) over a coat of primer of same make including necessary scaffolding for four storey building complete all as specified and as directed.

Cleaning and removing all scales and dirt etc from existing tanks and from mouths of circulating pipes etc for exceeding 250 litres but not exceeding 500 Litres capacity of tanks complete all as specified and as directed.

Cleaning and removing all scales and dirt etc from existing tanks and from mouths of circulating pipes etc for exceeding 500 litres but n.exc 1000 Litres capacity of tanks complete all as specified and as directed.

M&L for cutting trees including cutting of trunks and branches and digging out roots from floor or roof and walls making good the dismantled portion in cement mortar (1:3) girth of trees 30 cm, complete all as specified and as directed.

S&F in repair, aluminium sheeting 0.50 mm thick, fixed to wooden shutters with CP screws including cutting to required size etc complete all as specified and as directed.

S & F in repair mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tracks or galvanised wire staple complete all as specified and as directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each pane including hacking out old broken glass of any thickness/size of any description from steel / wooden frame glazed with putty or fixed with beads complete all as specified and as directed.

S&F 4 mm thick Figured glass ,pin head type and glazing with oil putty in sqm not exceeding 0.5 sqm in each pane etc. including hacking out old broken glass of any thickness/size of any description from steel / wooden frame glazed with putty or fixed with beads complete all as specified and as directed.

S&F in repair block board grade 2 quality , exterior grade commercial type 18/19 mm thick fixed in repair in copboard shutter & parations including 0.90 mm thick decorative laminate type 1 on one side surface finish of colour and pattern as approved fixed with approved adhesive complete all as specified and as directed.

M&L for prepration of new wood or wood based surface not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for welding in repair in any situation and in any position such as hinges and similar articles etc for steel door, gates, window, ventilatiors and grills etc for upto four stoery building complete all as specified and as directed.

M&L for 25 mm thick cement concrete type B-0, 1:2:4 using 12.5mm graded aggregate in sub base of floors etc complete all as specified and as directed.

M&L for non skid coloured ceramic tiles jointless 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set & jointed in neat cement slurry & pointed in coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 for laying floor finish including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and as directed.

M & L for glazed ceramic coloured tiles 350mm x 250mm x 7 mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match in vertical surfaces such as skirting /dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10m thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing coat including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and as directed.

M&L for Non - skid coloured Ceramic tiles 7 to8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but notexceeding 0.38 sqm, infloors etc. set and jointed inneat cement slurry andpointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and as directed.

Taking down chowkhats or frames with shutter exc. 1.5 sqm and n exc.4.00 Sqm each but without taking off shutters from the frame including make good disturb portion as the existing surfaces complete all as specified and as directed.

Taking down chowkhats or frames with shutter n exc 1.5 sqm each including making good disturb portion as per the existing surfaces complete all as specified and as directed.

Taking down shutter of any description exc 1.00 sqm nexc 2.00 sqm each complete all as specified and as directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and includin fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed.

S & F 35mm thick factory made both side prelaminated wire mesh solid PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 15mm x 15mm for top, lock & bottom rails. M.S. frame shall have a coat of metal primer of approved make and manufacturer. 19mm x 19mm M.S. square tubes shall be covered with heat moulded Prelam sheet 'C' channel made from 5mm (±0.25) thick PVC Sheet of Density 600 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, of size 35mm thickness, 115mm width out of which 100mm shall be flat and 15mm shall be bent in 90° angle on either side forming stiles,one of the 90° bend edge is cut from stiles as well as rails to nail from inner side of door to hide wire mesh fixing steel screws. 5mm (±0.25) thick 140mm wide PVC sheet out of which 125mm shall be flat and 15mm shall be bent in 90° on the inner side to form top and bottom rail and 155 mm wide PVC sheet out of which 100 mm shall be flat and 15mm shall be bent in 90° on both side to form lock rail. An additional 5mm (±0.25) thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent cement adhesive. Panel will be of GI /SS wire mesh of 24 gauge to be fitted inside area of stiles & rails. The wire mesh in top, bottom & lock rail is sealed with 15mm x15mm tube with steel screw of size 13/6 mm.10mm (5mm x 2nos) thick PVC strip of 25mm width is to be stuck & nails on both side of G.I. wire mesh interior at the top, bottom & lock rail. 10mm thick (5mm x 2nos) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardware’s should be fixed with 19*6mm size steel screws etc. complete all as specified and as directed.

S&F factory made solid panel FRP door shutter 30mm thick premoulded design made out of solid core, laminated 1.5 mm to 2mm thick GRP/FRP made of superior all seson, weather resistant polyester get coat followed by laminating polyster resin of 450 gm glass mat termite including 02 Nos Tower bolt, 06 Nos Hinges, 02 Nos handle best quality as per manufacturer's insruction and specified, including fitted to Angle iron chowktas with the welding arrangement all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 45 x 70 mm comprising of vigin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ricehusk/wheat husk) and non toxicadditives (maximum toxicity index of 12 for 100 g,s) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and including fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and as directed. Note:- For WPC solid door/window frames, minus 5 mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and including fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed.

Taking down of old steel window of any descreption complete all as specified and as directed.

S&F fabricated aluminum window with powder coated anodized aluminum frame of section 63.5mm x 38.10mm x1.5mm thick, shutter with section 47.62mmx44.45mmx1.5mm thick including aluminum anodized “D “ handle, hinges, peg stays, tower bolts, etc including jointing cleats for fixing builder's hardware fittings & stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples including necessary fittings/fixture /aluminum snap beads complete all as specified and as directed. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

M&L poweder coated aluminium anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5mm thickness (section no. 20831 of JINDAL) and of shutter size 40 mm x 18 (with 9.00 mm interlocking legs) x 1.45 mm thick (section no. 20737 of JINDAL) section (two shutter glazed, covering half of span of opening each & one shutter sketlon covering half of span of opening ) incl provn for making windows air tight, including 95mm aluminium handle with spring lock , stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4mm and fixed with steel wire stapples and 5mm thick plain glass including necessary fitting/ fixture/ aluminium snap beads complete all as specified and as directed. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 65 x125 mm comprising of vigin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ricehusk/wheat husk) and non toxicadditives (maximum toxicity index of 12 for 100 g,s) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and including fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and as directed. Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 65 x100 mm comprising of vigin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ricehusk/wheat husk) and non toxicadditives (maximum toxicity index of 12 for 100 g,s) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and including fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and as directed. Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F 200 mm long aluminium anodised barrel tower bolt extruded section all as specified.

S&F 150mm long extruded aluminium alloy handle complete all as specified.

S&F 100 mm long butt hinges medium wt cold rold mild steel including welding to frame.

M&L for preparation by complete removal of existing treatment , wahsing down and stopping of distempered and painted surfaces of old plastered or unplastered surfaces of wall and ceiling applying two coats of distemper oil emulsion, white or tinted over & including a coat of 1-2 mm average thick wall care putty complete all as specified and directed.

M&L for preparing old decorated steel surfaces of any description not otherwise described over 10 cm width or girth & applying two coat of synthetic enamel paint of any colour complete all as specified and as directed.

M&L preparation of old painted surfaces of wooden or wood based of any description not otherwise described width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

S&F mild steel 300 mm long ordinary rat tail rod pattern sprngs including roller and roller plate complete all as specified and as directed.

S&F Pre-printed galvalume aluminium zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw/ L-type or J type cranked hook including taking down of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

M & L for mild steel structural steel in roof, purlins crane of angle or other section gusset plates, Flat Iron rails braces etc, drilled for fixing, and other covering r etc to be prepared for hanging and sliding with and including either hooks and hinges and other covering running rails and guides and hanging also fastening and fixing complete. Fe- 410 Grade E-250 quality -Bl complete all as specified and as directed.

M & L for mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and as directed.

M&L for preparing of new steel surfaces of any description over 10 cm widthor girth and applying two coat of synethic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L for complete removal of existing loose treatment by scraping with mechanical wall/ceiling by vacuum based sanding machine (wall sanding machine with internal dust extraction system & having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 grit having dia of 7 ich/ 9 inches to make the surfaces free from dust, loose paint etc by using smart periodical methodology complete all as specified and as directed.

M&L for applying waterproof wall putty average thickness 1-2 mm to get even or smooth surface complete all as specified and as directed.

M&L for preparation of surface and applying two coats on wall/ceiling surface with Graco-490 spray machine, of Green Pro certified water-based, modified acrylic, exterior Apex Suprema Emulsion or equivalent as per required shade (Company depot tinted) with silicon additives, heat reflectant property, VOC less than 2% by mass, Class A IS-15489 and IS-101 @5-6sqm/ltr, over a coat of necessary tools and machinery to give an even shade. Application to be done only by applicator authorised by manufacturer, also shall be approved by GE before commencement of work.

M&L for preparation of old decorated wall surfaces by complete removal of existing treatment and applying two coats of cement base paint, white or tinted (colour and shade as per new colour scheme approved by GE) over a coat of primer of same make including scaffolding for four storey building complete all as specified and directed.

M&L for complete removal of existing treatment from internal surfaces of walls or a part thereof (In Patches ), area exe 1.00 Sqm but not exceeding 3.00 Sqm, which is damage due to seepage or any other reason & preparing and levelling the disturbed surfaces by using wall care putty (JK/Birla white) to obtain even and smooth wall surfaces over application for two or more coat of Dr Fixit or equivalent chemical treatment of that portion and using sand paper and than applying two coats of oil bound distemper over a coat of primer, including scaffolding arrangement, trestles, ladders, complete all as specified and as directed.

M&L for complete removal of existing treatment from internal surfaces of walls or a part thereof (In Patches ), area exceeding 3.00 Sqm but not exceeding 5.00 Sqm , which is damage due to seepage or any other reason & preparing and levelling the disturbed surfaces by using wall care putty (JK/Birla white) to obtain even and smooth wall surfaces over application for two or more coat of Dr Fixit or equivalent chemical treatment of that portion and using sand paper and than applying two coats of oil bound distemper over a coat of primer, including scaffolding arrangement, trestles, ladders, complete all as specified and as directed.

Disconnecting existing tanks of capacity 500 litre, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting at other place as directed and reconnecting , repair if required and re-fixing in position complete all as specified and as directed.

Disconnecting existing tanks of 1000 liter, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting at other place as directed and reconnecting , repair if required and re-fixing in position complete all as specified and as directed.

S&F in repair 15 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and as directed.

S&F in repair 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and as directed.

S&F 25 mm size Gun metal, globe or gate valvees, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Supply and Fixing 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps at one meter of interval including taking down of eaves gutter rain water pipe (any size of pattern) including all fittings, heads, shoes, bends, swan-necks and cleaning or fixing or removal , complete all as specified and as directed.

S&F PVC (SWR) bends/Tees of radius, suitable for 110 mm dia PVC pipes fixed complete all as specified and as directed.

Supply and Fixing 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps at one meter of interval including taking down of eaves gutter rain water pipe (any size of pattern) including all fittings, heads, shoes, bends, swan-necks and cleaning or fixing or removal , complete all as specified and as directed.

S&F in repairs for PVC (SWR) bends/Tee etc of radius, suitable for 75mm dia PVC pipes fixed complete all as specified and as directed.

M/S Malik Construction Corporation (BID ID -3363560)