84051/E8 SPECIAL REPAIRS TO CERTAIN SMQS AT TECH AREA UNDER GE AF JORHAT

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (Un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Cement Concrete (Reinforced) in Roofs, Floors (Other than Ground Floors), Beams, Staircases, Landing, Chajjas and Similar Suspended Work including Reinforce-ment cut as required to facilitate Demolition and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Masonry Work, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc. and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Chowkats or Frame (without Taking Off Shutter from the Frame) of any description, not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down Chowkats or Frame (without Taking Off Shutter from the Frame) of any description, exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheet or Galvalume Sheet (Corrugated, Semi-corrugated, etc.) of any Gauge and thickness, Segregating Serviceable Sheets and Stacking Properly at Sites and Keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Ceiling Frame (Snap Grid) with Hangers (but except Boards) of any descriptions, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not Backing) and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Dismantling Stone Slabs and/or Tiles of any description or thickness in Floors, Aprons, etc. laid, bedded and pointed in Cement Mortar and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including Raking out Joints, hacking for Key, scrubbing down with Water and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Taking up or down Steel Tubing 15mm bore (dia) and Fittings/ Connections of any description from any Situations, Segregating Serviceable Pipes & Fittings/ Connections and Stacking Properly at Sites and Keep in Safe Custody for re-use, complete all as specified and as directed.

Taking up or down Steel Tubing 20mm bore (dia) and Fittings/ Connections of any description from any Situations, Segregating Serviceable Pipes & Fittings/ Connections and Stacking Properly at Sites and Keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling/ Lowering down Unserviceable Water Storage Tank exc. 250 Litre but not exc. 500 Litre Capacity of any description after disconnecting of Water Supply Connections including Float Valve, complete all as specified and as directed.

Taking up or down PVC (SWR) Soil, Waste and Ventilating Pipe of any Size/ bore (dia) with Fittings of any description from any Situations, Segregating Serviceable Pipes and Stacking Properly at Sites and Keep in Safe Custody for Re-use, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (12.5mm graded stone aggregates) in Filling of Pressed Steel Frames/ Chowkats of Doors, etc., Finishing all Exposed Faces of Concrete including Use and Waste of Formwork if required/ ordered, complete all as specified and as directed. NOTE : Cost of Formwork will deem to be include in the Quoted Unit Rate.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregates) in Roof Kerbs or Mud Stops, Rounded or Chamfered on Edges, Finishing all Exposed Faces of Concrete including Use and Waste of Formwork as required/ ordered, complete all as specified and as directed. NOTE : Cost of Formwork will deem to be include in the Quoted Unit Rate.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregates) in Slabs supported on Walls, Beams and Columns in Floors, Roofs, Landings, Balconies, Deck Slabs, Canopies and in Shelves and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured & Paid for separately under appropriate Items here-in-after.

M&L Formwork to Soffits of Suspended Slabs such as Roof Slabs, Floor Slabs, Landings and Similar Work; not exc. 200mm thick (Horizontal or Sloping, Rough Finished surfaces of Concrete Flat, complete all as specified and as directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks) in Half Brick thick Walls, Straight or Curved on Plan to any Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cutting Holes in Brick Walling, exc. Half Bricks and not exc. One Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to Dismantled portion with Cement Concrete 1:2:4 (20mm graded stone aggregates) or Cement Mortar 1:3 (as required) and Adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cutting Chases for Concealed Water Tubing or Concealed Conduit Wiring, etc. and Making Good in Cement Mortar 1:3, Cutting on Brick Walls not exc. 25mm in Depth and not exc. 10 Cm in Girth including Providing necessary Surface Treatment (White/ Colour Washing/ Distempering/ Painting) wherever required to Match the Existing Finishes, complete all as specified and as directed.

S&F Pressed Steel Frames of Size 105x60mm, made out of 1.25mm thick Steel Sheets for Doors with One or More Rebates including necessary Fixing Lugs, Hinges, Lock Strike Plate, etc., complete all as specified and as directed.

S&F Pressed Steel Frames of Size 125x60mm, made out of 1.25mm thick Steel Sheets for Doors with One or More Rebates including necessary Fixing Lugs, Hinges, Lock Strike Plate, etc., complete all as specified and as directed.

M&L Flush Shutters 30mm thick, Solid Core Construction, with Block Board Core and Plywood Face Panels, Commercial type on Both Sides, Fitted to Chowkats, complete all as specified and as directed.

M&L Glazed and Skeleton Shutters 35mm thick, Open Rebated and Prepared to Receive Glass, Gauze, etc. (Without Sash Bars), Edges of Framing Plain, Chamfered or rounded. Fitted with Cut and Mitred Beads for Securing Glass, etc.; Sizes of Members of Shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a); Fitted to Chowkats, complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50x47mm made out of 5.0mm Plain Colour PVC Sheet reinforced with Mild Steel Square Tube and fixing in Opening, complete all as specified and as directed.

M&L Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) Plain Colour (Ivory shade) consisting of Frame made out of Mild Steel Tubes for Top and Bottom Rails, Mild Steel Frame shall be covered with heat moulded wood grain PVC ‘C’ Channel having a PVC Sheet Strip of 20mm width stuck inside with Solvent Cement for Stiles and Wood Grain PVC Sheets for Top Rail, Lock Rail & Bottom Rail on either Side and as gap insert for Top Rail & Bottom Rail, Panelling of Wood grain PVC Sheet to be fitted in the Mild Steel Frame welded/sealed to the Stiles and Rails with suitable 5mm thick x 15mm wide PVC Sheet Beading used inside Stiles and Rails and decorative PVC Beading of 10mm x 10mm (90°) and jointed together with Solvent Cement and fixing in the Frame and hanging/ fixing with and including Stainless Steel Hinges, complete all as specified and as directed. NOTE : Butt Hinges will be Measured and Paid under appropriate Item here-in-after.

S&F Steel Windows with Side Hung Shutters including Box type Hinges with Steel Handle and Steel Peg Stay, complete WITH GLAZING BARS, dovetailed or welded, complete all as specified and as directed.

S&F Steel Windows with Side Hung Shutters including Box type Hinges with Steel Handle and Steel Peg Stay, complete WITHOUT GLAZING BARS, dovetailed or welded, complete all as specified and as directed.

S&F Steel Ventilator with Top Hung Shutter including Hinges, Steel Peg Stay, complete all as specified and as directed.

S&F Aluminium Anodised Barrel Tower Bolt, 150mm Long, Extruded Section, complete all as specified and as directed.

S&F Aluminium Anodised Barrel Tower Bolt, 200mm Long, Extruded Section, complete all as specified and as directed.

S&F Aluminium Alloy Anodized Sliding Door Bolt 250mm Long with Hasp Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Section and fixing Bolts and Sliding Bolts of Extruded Section and Fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 75mm (as approved) and Fixing to PVC Door Frames for Hanging PVC Door Shutters, complete all as specified and as directed.

S&F Mild Steel Butt Hinge of Size 100mm, Heavy Weight and Welded to Mild Steel Door Frame for Hanging Door Shutters, complete all as specified and as directed.

S&F Aluminium Handle 150mm Long, Cast type, Anodised, Extruded and fixed, complete all as specified and as directed.

M&L Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Sheet Glass 4.0mm thick, Ordinary quality, Glazing in Metal or Wooden Frames and glazed with Oil Putty/ Wooden Beads, not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Sheet Glass 4.0mm thick, Figured Glass, Pin Head type, Glazing in Metal or Wooden Frames and glazed with Oil Putty/ Wooden Beads, not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, Cut to Length, Bent to Shape required, including Cranking, Bending Spirally for Hooping for Columns, Hooking Ends and Binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Framed Work such as Grills, Gratings, etc. with Ends of Bars shouldered and/or Riveted, or Forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walk Ways; Railings; Framework of Water Tanks and Similar Work, conforming to Fe-290, Gde-E-165, complete all as specified and as directed.

M&L Mild Steel Chimney Bars (Straight or Camber); Bearing Bars; Tongues or Water Bars for Window Frames; Window Guard Bars, Plain, Let in and fixed Independently in Wooden Frames, L or T Section Supports for Shelves, etc. and Similar Articles, etc., conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

S&F Pre-painted Galvalume Aluminium Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with and including Aluminium Self Tapping Screws and Aluminium Washers of suitable Size, complete all as specified and as directed.

Re-fixing Pre-painted Galvalume Aluminium Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured (Serviceable Sheets obtained from Sl No. 1.006 here-in-before) in Roof Covering, Cladding to Walls, fixed with and including Aluminium Self Tapping Screws and Aluminium Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminium Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with and including Aluminium Self Tapping Screws and Aluminium Washers of suitable Size, complete all as specified and as directed.

M&L Cutting Grooves in Brick Walls, 75mm Wide and 65mm Deep and Shaping Horizontal Face of Groove with Cement Mortar 1:3, complete all as specified and as directed.

Roughening Surfaces of Old Concrete Floor by Picking, Sweeping Clean and Washing Down with Water to Remove Dust, etc. and Brushing Neat Cement Slurry with 3.0 KG of Cement Per SQM, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded aggregate) Padding 25mm (ave.) thick, laid in Slope 1:40 at Top of RCC Roof Slabs/ Surfaces or Roof Kerbs including Mixing with Integral Water Proofing Compound as recommended by Manufacturer, Finish Concrete Surfaces Fair and Even, complete all as specified and as directed. NOTE : WPC will be Measured and Paid separately under Sl No. 1.067.

M&L Rendering 10mm thick in Cement Mortar 1:3 on Concrete Padding on RCC Roof Slabs, when the Concrete is Green, finished Plastered Surfaces Fair and Even, complete all as specified and as directed.

M&L Applying Evenly a coat of Bitumen Primer @ 0.40 Litre Per Sqm by the same Membrane Manufacturer after Proper Cleaning of Plastered Surfaces, complete all as specified and as directed.

M&L APP based Polymeric Membrane Minimum weighing 3.00 Kg Per Sqm and Minimum 3.0mm thick, Reinforced with Polyester Non-woven Fabric (Weight not less than 150 Grams Per Sqm), laid on Primed Surface with Side Overlap of 80mm and End Overlap of 100mm using Bitumen Torch or by LP Gas Torching and Sealing all Joints, etc. and ensuring complete Thermo Fusing and Applying One coat of Aluminium Paint over it, complete all as specified and as directed.

M&L Aluminium Anodised Snap Grid Frame Work of Grid Size 600x600mm for False Ceiling, complete all as specified and as directed.

S&F Hangers 4.0mm dia GI (upto 1200mm Length) for Adjusting Level, fixed to Roof Slabs by Means of Ceiling Cleats, made out of GI Flat 40x3.0mm in Size, 60mm Long and Expansion Hold Fasteners 12.5mm dia, 40mm Long, complete all as specified and as directed.

S&F Perforated Particle Board/ Tiles 12mm thick for Insulation and Accoustic Purposes 600x600mm in Size, Fixed with Screws to Frame Work or with Staples on Snap Grid in Ceiling, complete all as specified and as directed. NOTE : Snap Grid will be Measured and Paid under Sl No. 1.054.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregates) 40mm thick in Flooring, etc., laid in Alternate Panels, Finished Concrete Surfaces Even and Smooth with Using Extra Cement, complete all as specified and as directed.

M&L Glass Dividing Strips 38mm Wide and 3.0mm thick and inserted in Position, conform to Design, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregates) 25mm thick in Levelling/ Base for Receiving Tiles, etc., Maintaining Level Uniformly, Finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Rectangular or Square), Area of Each Tile exc. 0.06 Sqm but not exc. 0.11 Sqm (1st quality) in Floors, Set and Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 20mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed deem to be include in the Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Rectangular or Square), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality) in Floors, Set and Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 20mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed deem to be include in the Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 450x300x7.0mm thick in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Screed or Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Screed Bed deem to be include in the Quoted Unit Rate.

M&L Machine Cut Granite (of any type) Work 20mm thick (Table Rubbed and Polished) in Steps, Jambs, Pillars, Window Cills, Cooking Platforms and like in Cement Mortar 1:4 including Pointing in White Cement 1:2 Using Marble Dust with Admixture of Pigment to Match with Shade of Granite including Grinding and Polishing, Fixing Over and including Cement Screed Bed 20mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed will deem to be include in the Quoted Unit Rate.

M&L Rendering 5.0mm thick in Cement Mortar 1:3 on Ceiling Surfaces, finished Plastered Surfaces Fair and Even, complete all as specified and as directed.

M&L Rendering 15mm thick on Bricks or Concrete Surfaces in Cement Mortar 1:6, Finished Plastered Surfaces Even and Smooth Without Using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick on Bricks or Concrete Surfaces consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:6 and Float/ Top layer 5.0mm thick in Cement Mortar 1:4 including mixing WPC to Float/ Top, Finished Plastered Surfaces Fair and Even, complete all as specified and as directed. NOTE : WPC will be Measured and Paid separately under Sl No. 1.067.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Old Plastered Surfaces of Walls and applying Two Coats of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces on Ceiling and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing Old Plastered Surfaces of Ceiling and applying Two Coats of White Wash, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and Applying Two Coats of Distemper Oil Emulsion (of Approved Tint) Over a Coat of Chalk Whitening (Priming Coat), complete all as specified and as directed.

M&L Preparing Old Plastered Surfaces of Walls and Applying Two Coats of Distemper Oil Emulsion (of Approved Tint), complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and Applying Two Coats of Cement Based Paint (of Approved Tint) Over a Coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Plastered Surfaces of Walls and Applying Two Coats of Cement Based Paint (of Approved Tint), complete all as specified and as directed.

M&L Preparing Wooden Surfaces of any description, exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint), complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Old Painted Steel and Iron Surfaces of any description, over 10 Cm Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality / grade Paint of as approved Tint), complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), Medium grade, Conforming to IS-1239 with all Fittings, fixed to Walls or Concealed as ordered, Ceiling or laid in Floors, complete all as specified and as directed. NOTE : Cutting Chases as ordered and Making Good to Walls, Ceiling, Floors, etc. will be Measured and Paid separately under Sl No. 1.023.

Refixing Old Steel Tubing 15mm bore (dia) and Fittings (Serviceable Pipes and Fittings obtained from Sl No. 1.012 here-in-before) in New or Old Position (Walls, Ceiling, Floors or Concealed as ordered) including Cleaning both Inner and Outer Surfaces of Pipes & Fittings by using Wire Brush including Provision of New GI Fittings (as required ordered at Sites), complete all as specified and as directed. NOTE : Cutting Chases as ordered and Making Good to Walls, Ceiling, Floors, etc. will be Measured and Paid separately under Sl No. 1.023.

S&F Galvanised Steel Tubing 20mm bore (dia), Medium grade, Conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

Refixing Old Steel Tubing 20mm bore (dia) and Fittings (Serviceable Pipes and Fittings obtained from Sl No. 1.013 here-in-before) in New or Old Position (Walls, Ceiling, Floors, etc.) including Cleaning both Inner and Outer Surfaces of Pipes & Fittings by using Wire Brush including Provision of New GI Fittings (as required ordered at Sites), complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Fixed-in-repairs, complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy with Capstan Heads, Chromium Plated, Fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper Alloy, Fancy Type, Chromium Plated with Long Shank and Cup (Concealed type), with Crutch or Butterfly Handle, Screwed down, High Pressure, Screwed Both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 15mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 500 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule and Providing Water Connections with and including GI Tank Nipple 20mm (02 No. in Each Tank), complete all as specified and as directed.

S&F PTMT Ball Valve 20mm bore (dia), having Weight not less than 210 Grams, High Pressure with Epoxy coated Aluminium Rod and High Density Plastic Ball, screwed for Iron Pipe, complete all as specified and as directed.

M&L Disconnecting all the Pipe Connections, Cleaning & Removal of all Scales, Dirts, etc. from the Tank of capacity exc. 250 Litre and not exc. 500 Litre and Mouths of Circulating Pipes, etc. Cleaning the Tank by scrubbing the deposits with Wire Brush after draining out Water from the Tank, Re-hoisting the Cleaned Tank in Original Position and Re-fixing/Re-connecting Inlet and Outlet Pipes and Writing Letters/Figures "CLEANED ON : DD.MM.YYYY" (i.e. Date of Cleaning of Tank) with White Paint, Letters/Figures not exc. 50mm in Height, complete all as specified and as directed.

M&L Vitreous China White Squatting Pan of Size 580x440mm, Orissa Pattern with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) including Cement Concrete 1:5:10 (40mm graded stone aggregates) in Bedding and Making Good to Floor/ Disturbed Surfaces and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type, Dual Flush, ISI Marked (IS:7231) with Inlet, Ball Valve, Float and Handle, a Pair of Cast Iron Brackets Erecting Stand duly Painted, including PVC Flush Pipe 32mm dia with PVC Long Bend, Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China White Wash Hand Basin 580x450mm in Size, Flat Back, with Brass Chromium plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm or 40mm bore (dia) of Low or High density, a Pair of Cast Iron Brackets or Erecting Stand duly Painted, Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 but Excluding Taps, Chain, Plug & Porcelain Stopper and Fixed-in-repairs, complete all as specified and as directed.

S&F Kitchen Sink with Drainage Board, made of Stainless Steel l.0mm thick, Overall Size 915x460mm having Bowl Size 410x330x160mm with Plugs, Washers and Stainless Steel Waste Fittings, etc. including Bedding in Cement Mortar to dwarf Wall or fixing Cantilever Brackets and connecting Union to Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Plate Rack, made of 1.0mm thick, Overall Size 915x915x25mm (as approved), fixing to Walls with and including Chromium plated Brass Screws and Wooden/ Plastic Cleats and Fixing-in-repairs, complete all as specified and as directed.

S&F PTMT Waste Coupling of Size 32mm having Minimum Weight 45 Gram (Half or Full threaded) and Fixed-in-repairs, complete all as specified and as directed.

S&F Low Density Polyethylene Pipes (HDPE) 32mm bore (dia) of Pressure ratings 6.0 Kg/Sq Cm and Fixing to Walls, Ceiling or in Floors, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in size and 600mm in Length with PTMT Nuts and Fixed-in-repairs, complete all as specified and as directed.

S&F Brass Chromium Plated Shower Rose 125mm Size With or Without Swivel Joints including Fixing to Steel Pipe or Union and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Soap Dish, not less than 150mm in Size (as approved), Fixing to Walls with and including Chromium plated Brass Screws and Wooden/ Plastic Cleats and Fixing-in-repairs, complete all as specified and as directed.

S&F Towel Rail 600mm Long of PTMT (minimum Weight 190 Gram), Fixing to Walls with and including Chromium plated Brass Screws and Wooden/ Plastic Cleats and Fixing-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) Floor Trap 75mm bore (dia) with Chromium Plated Grating, Plain including Jointing to Waste Pipe with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, Fixing to Walls or Laid on Floors, complete all as specified and as directed.

Refixing PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints (Serviceable Pipes obtained from Sl No. 1.015 here-in-before), Fixing to Walls or Laid on Floors including Cleaning both Inner and Outer Surfaces of Pipes, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Bends (any Radius) and Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) PVC (SWR) Junction, Single (Single T), Equal or Unequal and Jointing with Solvent Cement, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down Carefully Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) complete from in any position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets (but excluding Light Fittings of any description), etc, Making Good Disturbed Surfaces of Walls/ Ceilings, etc. with Cement Mortar 1:3 and Providing Surface Treatment (White/Colour Washing/ Distempering/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed.

Taking down MCB DB/ Main Switch of any description including Making Good Disturbed Surfaces of Walls/ Ceilings, etc. with Cement Mortar 1:3 and Providing Surface Treatment (White/Colour Washing/ Distempering/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (25/32/40mm Width) along with all Fitting/Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. including suitable Size PVC Board with 3.0mm thick Hylam Sheet Cover for mounting Switches, Sockets, Regulators, etc., Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (25/32/40mm Width) along with all Fitting/Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. including suitable Size PVC Board with 3.0mm thick Hylam Sheet Cover for mounting Switches, Sockets, Regulators, etc., Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT POINT controlled by Two 2-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (25/32/40mm Width) along with all Fitting/Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. including suitable Size PVC Board with 3.0mm thick Hylam Sheet Cover for mounting Switches, Sockets, Regulators, etc., Earth Continuity Wire connected to Common Earth dolly for ONE CEILING/ EXHAUST FAN POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (25/32/40mm Width) along with all Fitting/Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. including suitable Size PVC Board with 3.0mm thick Hylam Sheet Cover for mounting Switches, Sockets, Regulators, etc., Earth Continuity Wire connected to Common Earth dolly for ONE BELL POINT controlled by One Bell Push, 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (25/32/40mm Width) along with all Fitting/Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. including suitable size PVC Board with 3.0mm thick Hylam Sheet Cover for mounting Switches, Sockets, etc., Earth Continuity Wire connected to Common Earth dolly for ONE 6 AMP SOCKET POINT on INDEPENDENT BOARD, controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire and connected to Common Earth dolly for ONE 6 AMP SOCKET POINT on SAME BOARD, controlled by One Another Switch, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (25/32/40mm Width) along with all Fitting/Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. including suitable Size PVC Board with 3.0mm thick Hylam Sheet Cover for mounting Switches, Sockets, etc., Earth Continuity Wire connected to Common Earth dolly for ONE 16 AMP SOCKET OUTLET POINT on INDEPENDENT BOARD, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, 1-way, Flush type, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Switch Bell Push 6 Amp, Flush type, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Switch Piano 16 Amp, Single Pole, 1-way, Flush type, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Switch Piano 16 Amp, Single Pole, 2-way, Flush type, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 5 Pin, Flush type, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Socket Outlet 16 Amp, 6-in-1, Flush type, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Ceiling Rose Surface type, Bakelite 65x50mm 2 to 3 Terminal suitable for 230 Volt AC, 6 Amp and Connecting up, complete all as specified and as directed.

S&F Ceiling Fan Regulator, Electronic Rotary Socket type, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F LED Light Fitting 1x10 Watt, 2 Feet, 230 Volt AC, Integrated, Decorative Box type with LED Light, Driver, Holder, Connecting up with 3 Core Flexible Copper Conductor Cable of suitable Size including Taking down/out Unserviceable Light Fitting, complete all as specified and as directed.

S&F LED Light Fitting 1x20 Watt, 4 Feet, 230 Volt AC, Integrated, Decorative Box type with LED Light, Driver, Holder, Connecting up with 3 Core Flexible Copper Conductor Cable of suitable Size including Taking down/out Unserviceable Light Fitting, complete all as specified and as directed.

M&L Street Light Fitting Bracket made out from GI Pipe 25mm Bore (dia), Light Grade, not exc. 1.50 Metre long, bend to required shape and fixing to Poles, etc. with and including Mild Steel Flat Iron Clamps 40x5mm of suitable Length, 2 No. Nuts, Bolts, Washers, etc. including Painting with One coat of Red Oxide Zinc Chrome Primer and Two coats of Aluminium Paint to all Mild Steel Works including Taking down Unserviceable Street Light Fitting Bracket of any description from any Height, complete all as specified and as directed.

S&F LED Building Security Light Fitting 35 Watt, 230 Volt, Outdoor, New Generation, Environmental Friendly, Energy Saving, Long Life, made up of Pressure Die-cast Aluminium Housing with Thermal Management in Multiple Optics, IP-66 protected, Impact Resistance of IK-07, Providing Electric Connections including Taking down Unserviceable Building Security Light Fitting of any description from any Height, complete all as specified and as directed.

S&F MCB 6 Amp to 32 Amp, Single Pole, 'C' Curve, 50 Hz, 10 kA, 240 Volt and Connecting up, complete all as specified and as directed.

S&F MCB 32 Amp, Single Pole & Neutral, 'C' Curve, 50 Hz, 10 kA, 240 Volt and Connecting up, complete all as specified and as directed.

S&F Factory made Distribution Board Sheet Metal Enclosure SPN 8-way, Double Doors, Front Openable, IP-43 Protected with 200 Amp rated Bus-bar for mounting Isolators & MCB's 240 Volt, fixed Flush with Wall inside the Niches or Outside on Wall Surface and Connecting up, complete all as specified and as directed.

S&F Factory made Distribution Board Sheet Metal Enclosure SPN 12-way, Double Doors, Front Openable, IP-43 Protected with 200 Amp rated Bus-bar for mounting Isolators & MCB's 240 Volt, fixed Flush with Wall inside the Niches or Outside on Wall Surface and Connecting up, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick buried directly in Ground (Earth Pit not less than 2.25 Metre below Ground Level) with Top edge of the Plate not less than 1.50 Metre below Ground Level, connected with and including Galvanised Earth Wire 4.0mm dia by means of Bolts, Nuts, Check nuts and Washers of GI or Steel and connected Earthing Testing Point/Bus-bar with GI 15mm bore (dia) Light grade Protection Pipe, Earth Plate surrounded by a Packed thickness of Char Coal or Coke Dust mixed with Common Salt in Alternate Layers of not exc. 150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of Size 450x450x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), Reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion including Taking down/out Unserviceable Earthing of any description, complete all as per specified and as directed.

DEDUCT/ LESS AGAINST SCHEDULE OF CREDIT

Bidders are required to Quote the SAME AMOUNT (as per SCHEDULE OF CREDIT at SERIAL PAGE No. 27 of Tender documents) under Column 5 i.e. 'UNIT RATE' (M) against Row No. 148.

INTERIOR DECCOR (BID ID -3055821)