Construction of One room including dressing and toilet and Garrage for Conversion of III type Judicial Residence into Type II Residence Quarter

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge:

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge.

1: 3: 6 or richer mix.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.

M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size).

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in:

Cement Mortar 1:6 ( 1-Cement : 6-Sand).

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Supplying and Filling in plinth with blown sand under floors including watering ramming consolidating and dressing complete including cost of sand.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Carriage of material Earth, Sand, Lime, Morrum manure or sludge lead upto 10 KM

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Random rubble dry stone Kharanja under floor.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering.

M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering.

M15 grade Nominal Mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Brick work with clay flyash F.P.S. brick (IS 13757- 1993 ) of class designation 75 in superstructure above plinth level upto floor five level in :

Cement mortar 1 : 6 (1 cement : 6 coarse sand)

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Half Brick work with mechanised autoclaved flyash lime bricks conforming to IS: 12894 :2002 of class designation 100 in superstructure above plinth level upto floor V level in.

Cement mortar 1 : 4 (1 cement : 4 coarse sand)

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. M20 grade Nominal Mix / Design Mix

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786)

Thermo-mechanically Treated bars (Conforming of relevent IS code)

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for :

Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Grading roof for water proofing treatment with water proffing compound

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F 1st qualityHeavy Duty Vitrified Polished Digital tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1: 4 including grounting the joints with white cement and matching pigment etc complete.

Size 600mm x 600mm

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4).

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F 1st qualityHeavy Duty Vitrified Polished Digital tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1: 4 including grounting the joints with white cement and matching pigment etc complete.

Size 300mm x 450mm

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Interlocking Paver Blocks having 120 mm thickness in M-50 grade concrete

Providing and Laying 120 mm thick cement concrete blocks of M-50 Grade(Manufactured with fully mechanised dry cast process with forced action mixer whose arms revolve along the main axis and rotate about its own axis also, having humidity sensor for moisture control of w/c ratio in concrete mix. Manufactured with steel moulds (Milled and manufactured in CSI diamond or CSI Nitro process for accuracy)on steel base plate of min 16 mm thick; Having Vibration and pressing action both together with the help of multiple synchronised vibrators. Power of hydraulic station should be minimum 50KW for compaction and cured in controlled chambers having humidity control and automated air circulation system) spreading 25mm thick sand underneath and filling joints with sand on existing W.B.M.base, as per IS15658:2006 and all materials shall conform to MoRTH Specification Clause 602.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing & fixing precast cement concrete coping 1 : 2 : 4 mix 50mm thick complete as per specification :

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Plaster on new surface on walls in cement sand mortar 1:4 including racking of joints etc. complete fine finish :

12mm thick .

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Plaster on new surface on walls in cement sand mortar 1:4 including racking of joints etc. complete fine finish :

20mm thick .

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3-fine sand)

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete

New Plastered Surface (three or more coats)

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Finishing walls with Acrylic Smooth exterior paint of required shade including all scaffolding. New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ).

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:

New work (two or more coats) over and including scrapping and priming coat with cement primer.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and fixing in CM 1 : 4 double paitam (rebated) stone door window and ventilator frames of approved quarry: Size 100 x 75mm.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' :

35 mm thick .

Commercial Veneer both side

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Extra for providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) Over item no. 8.13.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

30mm thick factory made solid panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 15 mm x15mm , top & bottom rails. M.S .frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC ‘C channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming stiles; and 5mm thick, 95mm wide PVC sheet out of which 75 mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75 mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2) thick, 20mm wide cross PVC sheet shall be provided as gap insert for top rail & bottom rail. Panelling of 5mm thick PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with 7mm (5mm +2mm) thick x 15mm wide PVC sheet bending on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the ‘C Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacture’s specification & drawing.(For W.C.and bathroom door shutter).

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and fixing of uPVC casement fixed windows or ventilators manufactured in ISO 9001:2000 & 14001:2004 certified company. Frame : Made from the Extruded uPVC Window Profile Section of size 60 x 60mm having outer wall thickness of 2.25mm (+/- 0.2mm) and 3 box multi-chamber construction, White in finish, duly reinforced with 1.2mm thick G/J/U/O TYPE GI section. All the four corners shall be mitered cut & thermal welded so as to form window frame. Frame shall be milled with drain and air equalizer hole in order to be water tight and for drainage of accumulated water, if any, to outer side. Fix Mullion made of 76 x 60mm uPVC Profile Section with steel reinforcement shall be provided in windows as per the requirement. Frame shall have ‘O’ type EPDM gasket fitted in in-built groove of frame profile for proper air & sound insulation of the shutter. Glazing bead of size 34 x 20mm with ‘K’ & ‘O’ type inner and outer EPDM weather seal gaskets alongwith 5mm thick ISI make plain float glass.All welding joints of frame and shutter shall be cleaned and milled with the CNC mechanism to provide uniform grooved finish on all visible joints. Hardware : Installation at Site : Complete window is to be installed on site with 10 x 100mm fastners with white cap in existing pre-finished wall cut-out cemented to glass level plane at all height & width and silicon glue is applied to fill up the crevices between wall and window frame. Complete in all respect as per the drawing and specifications and direction of engineer-in-charge.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and fixing of uPVC Sliding windows: Frame Made from the Extruded uPVC Window Profile Section of size 106w x 50h mm having outer wall thickness of 2.5mm (+/- 0.2mm) and 3 box multi-chamber construction, White in finish, duly reinforced with 1.2 mm thick GI section. Frame shall have three track configuration, two for sliding of window shutter and one for mosquito mesh shutter. Vertical member of frame which bears the sliding shutter load shall have aluminium rail/track for smooth sliding of shutter rollers. All the four corners shall be mitered cut & thermal welded so as to form window frame. Frame shall be milled with drain and air equalizer hole in order to be water tight and for drainage of accumulated water, if any, to outer side. Shutter : The shutter of sliding window shall be made of 39w x 69h mm Extruded 3 box multi- chamber uPVC Window Profile Section of white colour having outer wall thickness of 2.5mm (+/- 0.2mm) provided with reinforcement of 1.5mm thick GI section duly mitered cut & thermal welded at all corners and fitted with uPVC glazing bead of size 22 x 20 mm with inner and outer co-extruded EPDM/TPE-E weather seal gaskets alongwith 6mm thick ISI make plain float glass. Mesh shutter shall be made of 39w x 69h mm Extruded 3 box multi-chamber UPVC Window profile section of white colour having outer wall thickness of 2.5mm (+/- 0.2mm) provided with reinforcement of 1.5 mm thick GI section duly mitered cut & thermal welded at all corners and fitted with nylon/polymer mesh and rollers/pully.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitred welded and grinded including hold fast of steel lugs 13mm x 3mm and 15 Cm long embedded in C C block 15 x 10 x 10 Cm of 1:3:6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 50 x 25.0 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred and grinded including 10mm x 10mm square bars welded to frame for paitam fixing float glass 4mm thick panes with glazing clips and metal sash putty and fixing of shutters frames peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of Engineer-in –charge

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Supplying and fixing rolling shutters of approved make, made of 80 x 1.25mm. M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including cost of spring hooks, providing and fixing necessary 25.3cm. long wire springs grade No. 2 and M.S. top cover 1.25mm thick for rolling shutters as per design & IS 6248- 1979. (Clear openable area to be measured for payment).

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.

South Zed Black Above 3601 Cm2 Slabs

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and fixing wood panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled and glazed shutter 25 mm to 40 mm thick IS 710- 1976 marked 19 mm thick commerical ply

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and fixing Hollow core partition wall using 50x30 mm Chir wood frame 600 mm c/c on both directions,door opening as per drawing with steel fittings antitermite treatment complete as per specifications using : ISI 4 mm thick commercial ply with 0.80 mm mica with adhesive on both sides.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing & Fixing Premium Quality white glazed vitreous china Sanitary Wares (IS:2556 Mark) of approved make as per direction of Engineer-in-charge including cutting and making good the wall and floor.

Double Syphonic European W.C. with mounted W.V.C. flushing cistern of 10 litre capacity complete with all necessary internal fittings with Hydraulic seat cover.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall : Size 610 mm x 510 mm

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers. Other sizes

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Towel Rail or Ring of approved quality/make:

WVC (1stquality, IS2556 Marked) of approved make. Recessed towel Hanger size 108 x 108mm.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Towel Rail or Ring of approved quality/make:

C.P. brass Towel Rail elbow type with concealed screws size 600 mm (Heavy duty).

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Grating of approved quality/make:

Stainless Steel Sheet size 125mm dia. Heavy Quality of approved make

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Liquid Soap Container with brackets complete of approved make: C.P. Brass

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Soap Dish or Tray of approved quality/make C.P. brass heavy and superior quality.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Shower arm 15mm dia of approved quality/make. (-do-) size 370mm.(-do-)

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Bath Shower of approved quality/make.

C.P. brass of Heavy & superior quality, revolving with adjustable key 150mm.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Jet spray for water closet with C.P. Copper Tube flange of approved make.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing & Fixing premium quality Toilet corner Glass Shelf size 225x225mm with C.P. brass brackets & guard rail edges rounded of SS frame

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors:

a) Residence Quarter J-II/2 CJ&JM

Exposed on wall

15 mm dia nominal bore

'B' Class

25mm dia nominal bore

'B' Class

b) Residence Quarter J-II/1 JJB

Exposed on wall

15 mm dia nominal bore

'B' Class

25mm dia nominal bore

'B' Class

c) Residence Quarter SR-17

Exposed on wall

15 mm dia nominal bore

'B' Class

25mm dia nominal bore

'B' Class

P & F Pilllar Cocks (IS :8931 : 1993 Mark) of superior quality and approved make: C.P. Pillar cock, Swan-neck with casted spout, 15mm nominal bore.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: C.P. Brass bib cock,15mm nominal bore.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Ball Cock (IS :1703 Mark) with Rod & P.V.C. Ball complete : (-do-) wt.Not less than 600 gm, 25mm.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc.

---do--- with 37 cm long pipe and nut.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F 15 mm. Dia Connection Pipe of approved quality/make : PVC pipe with C.P. Brass nuts upto length,600mm

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 500 litres capacity

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Mixing Range (15mm) (-do-) with shower (wall type)

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P & F Divertors of superior quality and approved make: (-do-) Two way with 22Cm. Pipe flange

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. 110mm dia

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant:

a) Residence Quarter J-II/2 CJ&JM

Coupler (socket)

110mm dia

Reducer 110 X 75 mm

110mm dia

Plain Tee

110mm dia

110mm dia

Pipe Clip

110mm dia

b) Residence Quarter J-II/1 JJB

Coupler (socket)

110mm dia

Reducer 110 X 75 mm

110mm dia

Plain Tee

110mm dia

110mm dia

Pipe Clip

110mm dia

c) Residence Quarter SR-17

Coupler (socket)

110mm dia

Reducer 110 X 75 mm

110mm dia

Plain Tee

110mm dia

110mm dia

Pipe Clip

110mm dia

Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. Depth upto 0.5 M

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

-do- size 450 x 450mm depth upto 0.5 M Cement cover with frame

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Providing and fixing of false ceiling with grid of M.S.tube section of size 19mm X 19mm and with a wall thickness of 1mm+/- 0.2mm.The side pipe and the intermediate pipes is fixed to the roof from the top with the help of ceiling angles/wire grid shall be covered by the uPVC profile section of size 6mm X 250mm with wall thickness of 0.80mm +/- 0.2mm,with the help of self tapping screw of 6mm X 13mm, 6mm X 19mm.Necessary cutouts for electric connections, lighting, air conditioning etc, shall be provided at required place. The perimeter edge shall be covered by extruded PVC corner beading section of size 9mm X 28mm or 25mm X30mm with a wall thickness of 1mm+/-0.2mm fixed by applying cynoacrylic adhesive complete as per manufacturer’s specification and direction of Engineer-in-charge.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Supplying and fixing Rollor Blinds of good quality and approved make made out of Imported fabric including Roller Mechanism and lock with chain system with all necessary hooks etc. complete as per direction and sample approved by engineer-in-charge.

a) Residence Quarter J-II/2 CJ&JM

b) Residence Quarter J-II/1 JJB

c) Residence Quarter SR-17

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand)

Dark shade using ordinary cement.

b) Residence Quarter J-II/1 JJB

Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 20 KM disposed earth to be levelled and neatly dressed : All kinds of soil

b) Residence Quarter J-II/1 JJB

Providing and fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size.

Welded mesh 50 mmx 50 mm x 2.1 mm

c) Residence Quarter SR-17

Please Enable Macros to View BoQ information