REPAIRS MAINT TO INTERNAL WATER SUPPLY PIPE LINE, DOORS WINDOWS SEWAGE LINE DRAIN MANHOLES CLEANING WATER TANKS AND CERTAIN MISC WORK TO CERTAIN BLDGS AT KALINGA DWAR UNDER GE I GOS

Amount

Taking down chowkhats with shutters not exc. 1.5sqm each complete all as specified & directed.

Taking down chowkhats with shutters exc. 1.5sqm but.not exc. 4 sqm each complete all as specified & directed.

S&F 2nd class Hard wood in plain, solid, straight chowkats and frames wrought framed, rebated on the solid, rounded or chamfered put together with glue pinned joints complete all as specified and directed.

S&F Bands, straps, clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed.

M&L PCC 1:3:6 type C1 using 20mm graded stone aggregate for fixing of hold fast and making good complete all as specified and directed.

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes, as per specifications and drawing complete all as specified and directed.

M&L for Factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS Tubes for top & bottom rails M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement of stiles and plain colour PVC Sheets for top rails lock rail & bottom rail on eighter side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement , suppling & fixing in the frame at site complete all as specified and directed.

S & F 40 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides to match complete all as specified and directed.

M&L 30mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.23(b) complete all as specified and directed.

S&F 100mm size butt hinges extruded aluminium alloy with alloy with galvanised mild steel hinge pin, complete all as specified and directed.

S&F 75mm size butt hinges medium weight (ISI Marked), extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type-C21.complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type anodized complete all as specified and directed.

S&F 100mm size extruded aluminium alloy handles, fabricated type anodized complete all as specified and directed.

S&F in repair 150mm size extruded aluminium alloy handles, fabricated type anodized complete all as specified & directed.

S&F 150mm size Aluminium anodized barrel Tower bolts of extruded section and fixed complete all as specified and directed.

S&F 100mm size Aluminium anodized barrel Tower bolts of extruded section and fixed complete all as specified and directed.

S&F Aluminium alloy, anodized, sliding door bolt (ISI Marked) of 300mm with hasp & staple (Bolt type) and fixing clips of sheets, coat or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

M&L Preparation of new wooden surface exceeding 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F 2nd class hardwood Beads, straight (any size) for glazed or gauzed joinery, renewed, including mitres etc., and removing old beads to Store complete all as specified and directed.

S&F aluminium alloy wire cloth, 0.45 mm nominal dia of wire and averaging width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

S& F in repair Aluminium (extruded section) body Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified and directed.

S&F 300 mm long mild steel ordinary rat rail rod pattern springs including roller and roller plate, ISI marked complete all as specified and directed.

Hacking out old broken glass panes of any thickness, size ,quality or description from wooden frames, aluminium frame glazed with putty or fixed with beads in repairs complete all as specified and directed.

S&F glass pan ordinary quality 3mm thick and glazing with oil putty/ wooden beads in square n. exc 0.5 m each pane complete all as specified and directed.

S&F in repair vitreous china wash basin, white flat back size 580mmx450mm, excludings taps, waste, chain and plug and porcelain stopper but including brackets, complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with internal footrest (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repair Vitreous china bowl type Urinal flat back ,size 465x355x265 with grating and Union for discharge pipe including all necessary items complete all as specified and directed.

S&F in repairs Vitreous china wash down water closed pan ( Pedestal) white (exc flushing cistern & Pipe ) incl connection to trap and flushing pipe complete all as specified and directed.

S&F in repair PVC low level flushing cistern (white) 10 Ltrs capacity with internal fitting, push button operated type with and including bracket, PVC flush pipe etc complete all as specified and directed.

S&F in repair Sink with draining board made out of stainless steel 1.00 mm thick sheet for kitchen with plugs, washers and wastes including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm with bowl size 410 mm x 330mm x 160mm complete all as specified and directed.

S & F in repairs grating doom 125mm dia with waste hole of PTMT fixed on floor/nahani trap with cement mortar (Minimum weight 40 gms) complete all as specified and directed.

S & F in repairs PVC waste pipe 32mm dia, 60 cm long for WHB with cup, complete all as specified and directed.

All as per Item No 32 above but 40mm dia for sink complete all as specified and directed.

S & F in repairs Stainless steel waste coupling for S.S Sink 75mm to 100mm dia set with rubber washer plug etc complete all as specified and directed.

S&F in repair PVC connection 15 mm size, of length 450 mm, with PTMT nuts complete all as specified and directed.

Taking up or down steel water tubing and connections of following descriptions :- (a) 15 mm bore

(b) 20 mm bore

(c) 25 mm bore

Supply and laying CPVC pipes SDR 11 & Plain CPVC 11 fitting on walls/ceiling or laying in floor complete all as specified of following descriptions :- (a) 16 mm outer dia

(b) 20 mm outer dia

(c) 25 mm outer dia

All as per the description of above item here in before but re-fixing old steel tubing of following descriptions:- (a) 15 mm bore

(b) 20 mm bore

(c) 25 mm bore

S&F CPVC Brass Elbow (a) 16 mm outer dia

(b) 20 mm outer dia

S&F CPVC Brass Elbow (3/4 x1/2) 20 mm outer dia

S&F CPVC Brass Tee (a) 16 mm outer dia

(b) 20 mm outer dia

S&F CPVC Male Brass Threaded Adaptor (MTA/MBTA) (a) 16 mm outer dia

(b) 20 mm outer dia

S&F CPVC Female Brass Threaded Adaptor (FTA/FBTA) (a) 16 mm outer dia

(b) 20 mm outer dia

S&F CPVC Tank adaptor 20 mm outer dia

S&F CPVC Union (a) 16 mm outer dia

(b) 20 mm outer dia

S&F Lid (cover) of Rotational moulded polythelylene water storage tank capacity 500/1000 ltr complete all as specified and directed.

S&F EWC PVC sheet cover colour in white size 490mmx360mm complete all as specified and directed.

S&F in repair ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 15 mm bore (minimum weight 142 gms), complete all as specified and directed.

S&F in repair ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore (minimum weight 210 gms),complete all as specified and directed.

S&F in repairs gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20 mm dia complete all as specified and directed.

S&F in repair 15 mm fancy type pillar taps chromium plated cast copper alloy with capstan heads screwed down high pressure with or without lettered ‘Hot’ or ‘cold’ with long screwed shanks and fly nuts complete all as specified and directed.

S&F in repair 15 mm fancy type stop valve cast copper alloy chromium plated screwed high pressure with crutch or butter fly handle screwed both ends for iron or union and fixed to 15 mm GI tube complete all as specified and directed .

S& F in repairs CP Jt Spray/Health faucet with 1.5 mtr 15mm bore PVC Tube and hooke all as specified and directed MAKE : JOHNSON/JAGUAR ESSCO CAT NO -547

S&F in repair 15mm bore bib tap cast copper alloy chromium plated with crutch or butterfly handle fixed to 15 mm dia GI tube complete all as specified and directed.

Demolition of Cement concerte (unreinforced) in ground floor and paving n exc 15 cm thickness below or above ground level complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding complete all as specified & directed.

M&L for glazed ceramic tiles in vertical surface 350x250x7mm/450 x350 x 7 mm thick coloured on vertical surfaces such as dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match , including 15mm thick screed bed in CM 1 :4 complete all as specified and directed.

M&L for Non Skid ceramic tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match , including 15mm thick screed bed in CM 1 :4 complete all as specified and directed.

Taking down cement plaster of any description including raking out joints, hackisng for key, scrubbing down with water etc. complete all as specified and directed.

M&L for rendering 15 mm thick plaster in cement mortar 1:4 on fair faces of brick work or concrete surface of wall and finished even and smooth without using extra cement including taking down of plaster complete all as specified and directed.

M&L for rendering 10 mm thick plaster in cement mortar 1:4 on fair faces of brick work or concrete surface of ceiling/chajjas etc and finished even and smooth without using extra cement including taking down of plaster complete all as specified and directed.

M&L for rendering 5 mm thick plaster in cement and sand mortar 1:4 on concrete surfaces of ceiling including finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

All as per Item No. 75 above but but on ceiling complete all as specified and directed.

M&L preparation of new plastered surface and applying two coats of oil bound distemper over a coat of chalk whiting putty complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of wall including removal of vegetation and applying two coat of cement based paint complete all as specified and directed.

Dismantling PVC water tanks exc 500 ltr but n. exc 1000 ltr capacity and removing to store complete all as specified and directed.

Dismantling PVC water tanks exc 1000 ltr but n. exc 2000 ltr capacity and removing to store complete all as specified and directed.

S&F 500 ltr capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I.

S&F 1000 ltr capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I.

S&F in repair 100 mm bore cast iron waste and vent pipe in any length with or without ear with cement joints, fixed to walls complete all as specified and directed.

All as per item No 83 above but 75mm bore

S&F in repair 100 mm bore cast iron bend ( any radius) dimenshing pieces or tappers ( large bore measured) with oval access door complete all as specified and directed.

All as per item No.85 above but 75 mm bore

S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius

S&F 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius

S&F PVC (SWR) cowl of 110 mm dia

M&L complete removal of existing treatment including removal of vegetation and applying two coat of cement base paint complete all as specified and directed.

M&L complete removal of existing treatment on walls and applying two coats of oil bound distemper over 3 mm thick wall care putty to walls complete all as specified and directed.

M&L preparation of old painted wooden/wood based surfaces over 10cm width or girth and applying one coat (finishing coat ) of synthetic enamel paint complete all as specified and directed.

S&F Brass chromium plated shower rose 125mm size fixed Shower arm 15 mm size, 195mm long with bend of 45 degree with flange of PTMT any colour.(Minimum weight 40gms with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

M&L preparation of old painted steel surfaces over 10 cm width or girth and applying one coat (finishing coat) of synthetic enamel paint complete all as specified and directed.

Taking down existing water proofing membrance and cleaning roof, plastered surface etc preparing the surface to receive plaster by brushing with wire brush and fanning the surface to remove all loose dirt etc and brushing neat cement slurry @ 3.00 Kg/Sqm complete all as specified and directed.

M&L for rendering 15 mm thick surface as in roof with integral water proofing compound 3% by the weight of cement in cement mortar 1:4 complete all as specified & directed. (Integral WPC will be measured and paid separately).

Supply only Integral waterproofing compound.

M&L for water proofing treatment to roof surface complete all as specified & directed with the followings :- (a) Apply bituminous based primer confirming to IS: 3384-1965 @ 0.30 kg/sqm. (b) APP modified bituminous membrane 3mm thick with non woven polyester core of weight not less than 3.2 to 3.5 Kg/sqm laid and bonded to the sub strata by heat process, over laps of 100mm shall be sealed/fused by flame torch application as per manufacturer instructions. (c) Applying bituminous based aluminium paint @ 0.20 Kgs/Sqm in two coats over APP membrane.

S&F anodised aluminium glazed side hung double/single door shutters with anodised aluminium frame of section 100x44x 2.00mm and shutter having style, top rail, lock rail and bottom rail of 44.5X99X1.8mm including 5.5mm thick tinted sheet glass ordinary quality with all necessary suitable push & pull plate/handle, screw, jointing cleats, rubber packing, aluminium snap beading and 1 No 200mm long Al tower bolt, 100 msm long 3 No Al butt hinges B-21 type, and one No mortice brass lock 100mm size 4 leaver (vertical type) with double action floor spring hydraulically regulated made up of min 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavey duty (Make Sindhu /Samrat) for each shutters complete all as specified and directed.

S&F aluminium anodised galzed hung type window shutters made out from anodised aluminium frame of 'H' section size 34.00x43.5x2mm thick with 4mm tinted sheet galss (Weight not less than 0.57 kg/RM and shutter 'Z' of size 34.00x43.5x28.00mm having thickness 2.00mm (Wt not less than 0.50kg/RM) and all necessary jointing cleats , glazing, clips rubber packing, aluminium snap beading Tower bolt 100mm long 1 No and sliding hinges 180mm longs including aluminium grill with Mosquito proofing etc complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness,including nainital or similar pattern roof coverings complete all as specified and directed.

S&F steel work in tubular poles & trusses (unframed) including purlins,rafters and special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS-1161-1979 grade St-240.

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws incl ridge complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified and directed.

S&F 12mm thick plain Gypsum Board false ceiliing with GI frame work including all necessary drilling cutting to fix electric items compete all as specified and directed with following :- (a) GI Grid channel 30x25x20 mm of guage fixed with rawl plug and screw 450mm centre to centre alongwith perimete walls. (b) GI Channel made to shape 50x40x40 mm of 24 guage placed @ 600mm centre to centre from perimete at wall except long wall (in one span). (c) GI intermediate runners of size 45x10x10 mm of 24 guage fixed @ 1200mm centre to centre leaving frame of one side walls (in other span). (d) GI sheet 25mm wide and 20mm guage suspanded fixed with steel fastner to roof ceiling and 1200mm centre to centre including pluging of RCC slab. (e) 12mm thick gyplse board filling joints with POP and finishing complete with two coat of plastic emulsion paint over one coat of primer on ceiling.

M&L for prefabricated and prereinforced 75mm side POP moulded cornices/moulding fixed on ceiling/ wall complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise descri-bed, over 10cm width or girth not otherwise describe and painting with two coats of synthetic enamel paint over a caot of red oxide primer complete all as specified and directed.

M&L for removing of sludge from septic tanks including removal of sludge water manually or mechanically in all respect and removing the sludge to distance not exceeding 500 mtrs and burried in to the ground and making to a true surface and covering with loose soil complete all as specified and directed. (The rate included excavation and filling )

M&L for cutting and removing wild bushes/ vegetation, surface dressing around the septic tank/sock well/ manholes to a distance of 2 mtrs all around and depositing surplus spoil/ rubbish exc 100M but n.exc 500 M complete all as specified and directed.

Cleaning of sewage line (length from manhole to manholes) of any dia by roding and flushing after cleaning and removing mud/sludge etc to a distance exc. 250m but n.exc 500m and spreading in low laying areas and covering with loose soil complete all as specified and directed.

Cleaning of manholes and removing sludge from manholes of any size and depth and deposing the sludge and spreading in low laying areas and covering with loose soil complete all as specified and directed.

Cleaning the blockage of floor trap, nahani trap, gully trap and first man hole complete all as specified and directed.

Excavation in trenches n.exc 1.5M wide and n.exc 1.5 M deep for foundation and getting out in soft/loose soil complete all as specified and directed.

Demolition and breaking up drain pipe of any description up to 150mm dia in CM 1:4 including demolition of cement concrete bedding and hunching complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in concrete bed to drain pipe including packing under, and haunching against the sides of pipes after they are laid and tested for 150mm dia pipe complete all as specified and directed.

SF 160mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches complete all as specified and directed.

S&F 160mm bore PVC (SWR) bends any radius

S&F PVC (SWR) cowl of 160 mm dia

Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm bore drain pipe.

Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 200 mm bore drain pipe.

M&L for cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation and mass soncrete complete all as specified and directed.

M&L for cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as benching , surface channel and similar articles finishing even and smooth using extra cement complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in copings, bed plate, including weathering, slightly rounded or chamfered angles and throating with necessary form work complete all as specified and directed.

Returning, filling in, including spreading levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Demolition of brick work built in cement mortar complete all as specified and directed.

M&L Brick work with fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1:6 Complete all as specified and directed.

M&L Rendering 10 mm thick in cement and sand mortar 1:6 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and directed.

Demolition of RCC of any description and in any position not other wise specially provided for reinforcement cut as required to facilitate demolition complete all as specified and directed.

M&L for pre cast cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in cover slabs (for manholes etc) and similar articles with plain faces, set in CM 1:4 complete all as specified and directed.

M&L for mild steel 6 - 8mm dia TMT bars bent to shape required, including cranking, bending and binding with mild steel annealed wire not less than 0.9mm dia complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks exc 250 ltr n.exc 500 ltr capacity and from mouths of circulating pipes, etc. including Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position.

Cleaning and removing all scale and dirt, etc, from tanks exc 500 ltr but n.exc 1000 ltr capacity and from mouths of circulating pipes, etc. including Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position.

M&L for Repair to pot holes any depth, not exc 1 sqm each including sweeping free from dust and mud or water, scoring sunken surfaces in roads, paths, etc cutting around edges to at least 25mm in depth, and making good by applying tack coat @ 5 Kgs per 10 Sqm and laying premixed bituminious macadam well rammed and sealed with paving bitumen 60/70 or VG-30 grade@ 9.8 Kgs per 10 Sqm, blinded with 0.09 Cum of stone chipping of size 6.3mm and again well rolled with 8 to 10 tonne power roller (Iincluding supply of pre-mixed macadam, binder and chipping) depth of pot holes exc 30mm complete all as specified and directed by Engineer-in-Charge.

M&L for Preparing existing black top surface or bituminous macadam surfaces by brushing with brushes for removing caked mud etc sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc on back top/concrete surfaces than applying evenly priming tack coat with paving bitumen 60/70 or VG-30 penetration over the prepared surface by mechanical sprayer @ 5 Kgs/10 Sqm of surface area complete all as specified and directed by the Engineer -in-Charge.

M&L for applying bituminous premixed semi dense asphaltic concrete 30mm thick (consolidated thickness) with 5.5% binder content of paving bitumen 60/70 or VG-30 grade by weight of total mix including cement filler, on surfaces rolled & compacted with using 8 to 10 tonne capacity power roller to achieve the required compactness, camber and gradient mixed in hot mix plant using design mix and laid by mechanical paver finisher complete all as specified and directed by the Engineer-in-charge.

M&L for premixed bituminous macadam laid, rolled and compacted to required gradient and camber n.exc 75mm thickness (consolidated thickness) with 4% binder content of VG -30 by weight of total mix, mixed in hot mix plant and laid by mechnical paver finished complete all as specified and directed.

M&L for preparation of existing bituminous surfaces, removing, dust, dirt grease and other foreign matters etc to receive the marking and M&L for thermo plastic (Reflective) line marking having 1.0 mm thickness (average) of uniform surface finish conforming to BS 3262 (Part 1) 1989 read in conjunction with the MOST specification 803 clause 4.2.2 on bituminous surfaces in white/yelow clour and super imposed with glass beads confirming to BS 6088 read in conjuction with and MOST specification 803 clause 4.3.3 complete all as specified and directed. Note - MOST specification 803 shall be followed strictly for execution of work & suitable machine shall be used for the marking as approved by the GE. Shape & size/ patterns of marking shall be as approved by the GE.

S&F in repair cat eyes/road studs for roadways sign permanent surface mounted type having tough poly carbonate micro replicated corner cube reflector lenses with a protective abrssion resistant ceramor coating having body of weather proof and impect resistant thermoplasit complete as per manufacturer,s instruction and as directed. (Colour :- Yellow/Red/Amber) Make: Series 290 of 3M or Road Star or Equivalent.

S&F in repair plastic speed bumbs (Speed breakers) not less 400 mm wide blocks & yellow colours fixed with necessary spikes/screws to the road surface etc. Complete all as specified and directed by Engr -in - Charge.

S&F in repair solar cat eyes/road studs size (mm) 125L x 125B x 25H including stem height 53mm approx housing dia cast aluminium (grade LM-6) fully water proof and weather proof and weatherproof coating visible distance upto 400mtr LED-6 super bright amber led (3 Nos each side) yellow charged, flush frequency 1.2 Hz-1.8Hz including solar panel 3.5V/110MA & battery one PC sub ‘C’ type Ni-Cd rechargeable battery 1.2V/2.5AH temp range 20C to 70C fixed on road for roadway sign complete as per manufacturer’s instruction and directed by Engr-in-Charge. Make- 3M/Avery Dennision/Dark Eye/Green/Greenlite/Road Star Cat Part No. GSR-909 or Equivalent.

DHABALESWAR ENGINEERING WORKS

G.KRISHNA MURTHY AND PARTNERS

M/S JAGANNATH SASMAL

M/s MAA BHAIRABI ENTERPRISES

M/s Ats Electricals

MM ENGINEERING SYSTEMS

Likitha Enterprises