PROVN OF PROTECTIVE IRON GRILLS AT VARIOUS LOCATIONS OF NOFRA ADD ALTN AND SPL REP TO LIGHT POLES AND COMPOUND WALL OF TENNIS COURT AT IMSC ADD AND ALTN TO WALLS OF GYMNASIUM OF WNC (O) MESS AT NOFRA COLABA MUMBAI AND ADD AND ALTN TO CONCERTINA COI

Amount

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble, mixed with earth around, in layers n exc 25cm, watering and removing surplus soil to a distance n exc 50m and making surface good in hard/dense soil complete all as specified and directed.

Material and labour for Cement concrete (1:3:6) type C-2 (40mm graded aggregate) in foundations, filling and mass concrete complete all as specified and directed.

Supply and fixing posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets/pipes (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 , complete all as specified.

Material and labour for TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long & dia of neck 5 to 10mm

Supply and fixing Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete.

Preparation of new steel surfaces & apply two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified.

Supply and fixing Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

Material and labour for 100mm thick cement concrete type D-2 1:4:8 (using 40mm graded stone aggregate) as in sub base

Material and labour for heavy duty cement concrete interlocking paver tiles 80 mm (M 35 grade) thick having glossy finish with grey cement and no pigment (colour and pattern approved by GE) (tested as per IS 1237-1980) laid over and including 25 mm thick dry sand cushioning and voids filled with dry and surface compact, including compation by means of surface vibrator, complete all as manufacture instructions specified and directed.

Taking down cement or cement lime plaster of any description on brickor stone walls, etc including raking out joints, hacking for key, scrubing down with water, etc including errection of double steel scaffolding, covering with green cloth etc all as specified and directed by Engineer In Charge

Material and labour for rendering 15mm thick CM 1:6 on fair face of brick work or concrete surfaces of walls and finised surfaces even and smooth without using extra cement.

Material and labour rendering 10 mm thick cement plastering on brick or concrete surfaces in CM (1:4) finished even and smooth without using extra cement all as specified and directed, as in ceiling.

Material and labour preparation of new plastered or unplastered surfaces of walls including scrapping and applying two coats of oil bound distemper over layer of smooth Putty finish as required punning 3mm thick over a coat of primer strictly as per manufactuure instruction with smooth roller finish complete all as specified and directed.

All as item No 14 above but on ceiling complete.

Material and labour Preparation of old painted wood or wood based surfaces of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint with smooth roller finish etc complete all as specified and directed by Engineer- in charge. MAKE : Asian ( Apcolite) or Nerolac ( Hi- gloss) or Berger (Luxo Hi- glossl)

Material and labour Polished granite stone slab 18 to 20mm thick coloured as in cooking platform/door cills , set and jointed with grey cement slurry and pointed in neat white cement slurry mixed with pigment to match the shade of floors, including moulding at front edge or both edges and 20mm thick screed bed in cm 1:4 all as specified and as directed by EIC complete. Note : Quality of granite all as approved by GE

Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface including sunk or raised moulding over and including metal frame work and GI wire mess all as specified and directed by Engr-in-Charge.

Material and labour plain cement concrete 1:3:6 type C1, (20mm graded aggregate) for fixing hold fasts complete all as specified and directed.

Supply & Fixing 12mm thick tinted and polished toughened glass for door & fixed with ething including aluminium framing, door handle, suitable hinges, rubber beading, floor spiring and all necessary fittings as per directed by Engineer - in- Charge including taking down existing glass door and fixing of glass and removed debris away MOD land

Material and labour for 10mm thick digital coloured dark shade double charge vitrified tiles of size (square/ rectangular) polished area of each tiles n.exceeding 0.36 sqm in floor etc, with & including 5mm thick adhesive of Ferrouscrete (FERRO-1122) / Fevimate XL- Pidilite / Gold star of Bal Endura or equivalant including necessary roughning of existing PCC flooring & levelling the floor if required, grouting the joints complete all as specified and as directed by Engr-in-charge.

Material and labour for brick work built in cement mortar 1:6 with sub class B bricks straight or curved on plan exc 6m mean radius.

Demolition of existing treatment of any type and preparing the surface by cleaning the concrete surface with wire brush and a high pressure water jet and ensure that it is free of dust, oil grease, loose particles vegetation roots etc and filling crackswith polymer modifed mortar using smartcare RP or Epoxy mortar including material and labour for laying padding cement concrete in terrace 1:2:4 type B-0 (using graded stone aggregate) of 50mm average thickness maintaining 1:30 slope finishing with 10 mm thick cement mortar 1:3 as specified and directed by Engr-in-Charge. Material & labour for High performance hybrid polyurea elastomeric waterproofing spray applied SmartCare Hypertron Hybrid liquid membrane with an elongation of 600% and tensile strength of more than 13 N/mm2 as per ISO 527 type 5 , shore A Hardness of min. 85 as per ISO 868, and crack bridging ability of 3.5 mm as per ASTM C1305. The system includes final base preparation, epoxy primer application and applying SmartCare Hypertron Hybrid or approved equivalent in two coats with a consumption of 2kg/sqmt, etc., complete as per Manufacturere specifications

Material and labour for 20mm thick plastering in cement & sand mortar 1:4 in 2 coats (15 mm thick backing coat and 5 mm thick setting coat mixed with water proofing compound) on fair faces of brick work or concrete surfaces, finished even and smooth (w/o using extra cement) all as specified and directed

Preparation of new plastered surfaces of walls/Ceiling and applying two coats of acrylic emulsion exterior grade (100%) over a coat of primer complete all as specified and directed. incl all necessary scaffolding etc.

Material and labour in repairs MS work (flat iron, round bar) and framed brackets of angles, joist, channel, grill/grating, angle or tee sections fixed independently without connecting plates ect cut to shape (cut to ordinary length i.e within 20mm of the length indicated) drilled and cuntersunk for screws, including bending and welding as necessary, confirming to fe-410-0 or fe 310-0 including removing of old brackets and remove to store including necessary welding and nut & bolts complete as specified and directed.

Supply and fixing rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW (electric run welded) or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete fabrication, erection and all as specified and directed.

Fixing for chain link MS galvanised fencing any size or type including line wires, any mesh, size and type to any type standards, rails, straining bolts, etc. including provision of binding wire and including necessary nut and bolts, complete all as specified and as directed.

Supply only chain link MS gavanised fencing, any size or type

Material and labour Preparation of new or previously untreated surfaces on steel based surfaces of any description exc 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of primer with smooth roller finish etc complete all as specified and directed by Engeer- in charge.

Excavating in trenches,in hard soil n exc 1.5 m width n exc 1.5 m depth in any type of soil and getting out all as specified and directed.

All as item no 31 above but exceeding 1.5 m depth

Supply and fixing Reinforced concrete pipes, class NP2, 300 mm dia laid and jointed complete with collars all as specifed and directed.

Supply and fixing Reinforced concrete pipes, class NP2, 200 mm dia laid and jointed complete with collars all as specifed and directed.

Demolition of cast iron or reinforced concrete drain pipes, jointed in cement mortar internal dia of pipe 300 mm and taking out of trenches, if required

Demolition of cast iron or reinforced concrete drain pipes, jointed in cement mortar internal dia of pipe 200 mm and taking out of trenches, if required

Supply and fixing for providing, lowering and laying HDPE DWCPE (SN8) pipes as per IS : 16098 of 2013, 200 mm bore, laid and jointed with and including elastomeric sealing 'O' ring as per manufacturer's instructions complete all as per specified and directed. (Note - The rates include for laying pipes level or to falls in trenches, etc. on concrete bed or directly on hard ground as indicated and making joints and testing as specified.The rates include for all necessary extra joints, waste, and cutting etc.)

Supply and fixing for providing, lowering and laying HDPE DWCPE (SN8) pipes as per IS : 16098 of 2013, 300 mm bore, laid and jointed with and including elastomeric sealing 'O' ring as per manufacturer's instructions including dismantling complete all as per specified and directed. (Note - The rates include for laying pipes level or to falls in trenches, etc. on concrete bed or directly on hard ground as indicated and making joints and testing as specified.The rates include for all necessary extra joints, waste, and cutting etc.)

Material and labour PCC in 1:3:6 type C-2 300 mm dia using 40 mm graded aggregate Concrete bed to drain pipes including packing under and for hauching & Benching against the sides of pipes after they are laid and tested all as specified and directed. (Note :- (i) Thickness of bed below the barrel of pipes: 15cm for pipes 200mm dia and over. (ii) Width of bed: Outer diameter of drain pipes (not of sockets/collars) plus 30 cm (iii) The rates include for any necessary shuttering and supports to concrete and for laying beds to falls.

Material and labour PCC in 1:3:6 type C-2 200 mm dia using 40 mm graded aggregate Concrete bed to drain pipes including packing under and for hauching & Benching against the sides of pipes after they are laid and tested all as specified and directed. (Note :- (i) Thickness of bed below the barrel of pipes: 15cm for pipes 200mm dia and over. (ii) Width of bed: Outer diameter of drain pipes (not of sockets/collars) plus 30 cm (iii) The rates include for any necessary shuttering and supports to concrete and for laying beds to falls.

Material and labour PCC 1:4:8 type D2 ( 40 mm graded aggregates) as in foundation of Manholes complete all as specified and directed.

Material and labour Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 including demolition all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.in any type of soil all as specified and directed.

Removing excavated material outside MD land exc. 1.50 km but n exc. 15 km and depositing where directed.

Material and labour Rendering 15mm thick plaster in cement mortar 1:4 on brick or concrete masonry walls, finished even and fair without using extra cement complete all as specified and directed.

Material and labour PCC 1:2:4 type B1 ( 20 mm graded aggregate ) as in copings & in drains etc including necessary formwork & moulds all as specified and directed

Material and labour Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe Fe 290 Gde E-165

Cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters and similar articles

Supply and fixing MS plate (CHEQUERRED) 5mm and over as in manhole cover fixed to angle iron frame with three Nos of hingeg and 150mm handle. complete all as specified.

Extra for forming fair finished drain or channel 30cm inner grith in cement concrete , using extra cement including forms, moulds , mitred / stopped ends etc (Note : Inner grith only will be measured & paid.)

Dismantling wrought iron or mild steel work of any discreption other wise provided for.

Preparing black top surfaces by brushing with wire brushes for removing caked mid etc sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc.

Applying evenly a priming/tack coat with bituminous primer at 10 KGs/10 Sqm using paving bitumen on unsurfaced surfaces.

Material and labour for Bituminous premix Semi dense asphaltic concrete 40 mm consolidated thickness with 5.5 % binder content by weight of total mix. Rolled and compacted with static and vibratory roller to required camber and gradient complete. Binder content of grade VG-30 and all as specified and directed by Engr-in-charge.

Material and labour premixed bituminous macadam laid/rolled and compacted to required gradient and camber (consolidated thickness more than 75mm )using paving bitumen any penetration,binder content of 4% by weight of total mix.

Repairs to pot holes any depth not exceeding 1.00 sqm each including sweeping free from dust and mud or water scoring sunken surface in roads, path etc, cutting around edges to at least 25mm in depth and making good by applying tack coat @ of 5 Kg/10 sqm,putting in premixed bituminous macadam, well rammed and sealed with binder 9.8Kg/10sqm blined with 0.09Cum of stone chippings, 6.3mm size and again well rammed(including supply of premixed macadam binder and chipping) depth exc 30mm.

Supply and fixing in repair solar power twinkling road stud fixed with epoxy resin red colour complete as manufacturer instructionsMake-3M/AUTOMATE.

Supply and fix in repair road studs/cat's eye reflective type plastic body 100x100x26mm complete all as spfd and directed Make-3M/AUTOMATE

Preparation of black bituminous road surface and applying thermo plastic road marking paint, minimum 2 mm thick with applicator machine and heated mixer with stirring mechanism at temperature 160 degree C, laid uniformly with width as directed, painted conforming to BS-3362 Part I and II of 1989 etc, complete all as per manufacturer instructions and as directed by EIC Make: Shivalik/CMS Ltd/Automat Road Safety Ltd/Hotherm plast Engers.

Raising the existing chambers in road portion of any description type and size by taking out the existing covers and frames, exposing chamber area not existing 1.00 sqm by cutting existing road for raising the chambers up to 15 cms or as required with brick work in CM 1:4 or plain cement concrete (1:2:4 using 20mm stone aggregate) and finishing the surfaces with 15 mm thick plaster in CM 1:3 refixing the covers of RCC/MS/CI etc to match the existing road surfaces, removing debris out side MD land complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thick above or below ground level all as directed.

Material and labour Hardcore of gauge exc. 63 mm, of broken stone or boulders deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.

Material and labour PCC type B-2, 1:2:4 100 mm thk using 40 mm graded aggregates as in Floors & pavings etc all as specified and directed.

Material and labour 100 mm thick cement concret type C-2 1 : 3 : 6 ( 40 mm gaded aggregate as in floor repairs, sub base similar work complete all as specified

Material and labour plain cement concrete interlocking tile 80mm (M 35 grade) thick having glossy finish, pattern as approved by GE strength not less than 350 KG/Sqcm (tested as per IS 1237-1980) laid over and including 50mm thick dry river sand cushioning and voids filled with dry sand and surface compacted with surface vibrator complete all as per manufacturer instructions, specified and directed by EIC

Material and labour for brickwork with sub class `B' bricks (old size), straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 including demolation complete all as specified and as directed.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer etc complete all as specified and as directed.

Material and labour Rendering 20mm thick on other than fair face of brick work or concrete in two coats (15mm thick and 5mm thick cement mortar 1:4) each coat mixd with water proofing powder at the rate of 2% of cement or as per manufactures instruction sand faced, rendering is to be finished even and smooth(without using extra cement) complete all as specified and directed . Note: Water proofing compound shall be measured and paid separetely.

Supply only Integral water proofing compound.

M&L PCC 1:2:4 type B1 as in post holes and foundation using 20 mm stone aggregrate complete all as specified and directed

Supply and fixing in repair PVC insulated, stranded copper conductor of size 3 core 4.0 Sqmm in connection of FRP type looping box to light fitting connector, passing through GI pipe / tubular pole complete with fixing arrangement all as specified and directed . Make- Polycab/ Finolex/Havells

Supply and fixing High intensity LED flood (Warm White) light fittings 400 W, specially designed for sports/Search etc. Alluminium housing , polycarbonate secondary optic cover, IP 66, > 110 lm/watt, 10KV SPD and wired with all acessories.Make: SHAKTI CAT PART No. SZCFLPH400HB or Havells/Jaquar

Supply and fixing in repairs steel tubular swaged street light poles complete with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP-64, 12.00 mtr long and painting with two coat of aluminium paint over one coat of primer on exposed surface of pole all as specified and directed by Engr-in-Charge. NOTE :- Excavation will be ,measured and paid seperately Make :- National / Bombay poles.

Supply and fixing in repairs FRP type looping box of size 300 x 200 x 125 mm with necessary arrangement to fix the looping box with suitable size of cable glands with entry, nuts, bolts, washer flat iron including 3 core 2.5 sqmm wire from looping box to light fittings connector etc comprising of the followings:- (a) bus bar -04 Nos (b) Insulator - 08 Nos (c) Nut and bolts for cable joint as pre requirement

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation filling mass concrete including necessary form work.

M&L PCC 1:3:6 type C2 using 40 mm graded aggregate block masonry with solid block, exc 10 cm in width and setting in mortar complete fot coping of pole including necessary from work and fair finish to the exposed surface area without using extra cement complete all as specified and directed.

Supply, laying, commisssion & testing in repairs XLPE insulated armoured LT cable, 110 Volts grade with aluminium conductor of size 4 core 16 Sqmm laid in trenches/ through pipe/ ducts or fixed on wall etc complete all as specified and directed. Make - Polycab/ Finolex / Havells

Supply, laying, commisssion & testing in repairs XLPE insulated armoured LT cable, 110 Volts grade with aluminium conductor of size 3.5 core 50 Sqmm laid in trenches/ through pipe/ ducts or fixed on wall etc complete all as specified and directed. Make - Polycab / Finolex/ Havells

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mr in depth for foundation, laying of UG Electric cable / staying of steel tubular pole etc. And getting out in soft and loose soil and making good disturbed surface to match

Removing the excavated material/soil not exc 50m out of MD land complete all as specified and directed.

Supply and laying in repairs high density poly-ethylene pipes (HDPE) of pressure 6 kgf/cm2 pipe, 50 mm dia for laying of cable protection complete to walls/trenches/floor/ceilings all as specified and directed by Engr-in-charge.

Supply & fixing in repairs LED Flood light fittings 250 Watt (Warm White) capacity in aluminium pressure die cast housing with toughened glass cover, High Power LED, secondary optics, IP 65/66, 10KV SPD, >100lm/Watt including wiring complete all as specified & directed. Make - CAT Part No. SZCFLPH250 of Shakti or equivalent in Jaquar/ Philips/ Havells

Supply & fixing in repairs LED Flood light fittings 120 Watt (Warm White) capacity in aluminium pressure die cast housing with toughened glass cover, High Power LED, secondary optics, IP 65/66, 10KV SPD, >100lm/Watt including wiring complete all as specified & directed. Make - CAT Part No. SZCFLPH120 of Shakti or equivalent in Jaquar/ Philips/ Havells

ASHOK CONSTRUCTION

SHREE JAGDISH FURNITURE CO.

DHARICHHAN ENTERPRISE

MUKESH CONSTRUCTION CO