PROVN OF ATTACH TOILET AND BATHROOM FOR MO IC ROOM AT MH BAKLOH

M & L for point wiring with copper conductor cable multistrand, FRLSH PVC sheathed 1.5 Sqmm size (two run with colour code RYB ) for one light point , fan point ,exhaust fan point ,or bell point controlled by one switch including one run of 1.5 Sqmm (as continous earth wire Green) multistrand PVC concealed conduit of approved size and quality ISI marked , including all other required accessories as specified in preamable 1 (a) to (q) of section 19 of SSR Part -II under heading 'point wiring' fixedon wall /ceiling including sunk cast iron terminal boxes grouting/ flushing on wall for mounting fittings like switch, socket etc covered with 3.00 mm thick plastic laminated sheet top cover of brick masonary/stone masnoary wall complete including cutting, chasing, pinning and making good the disturbed surface by using cement mortar 1:3 complete all as specified and directed by Engr-in-charge. Make of wire /cable -Havells/Anchor/Finolex, (Note:- the rate for concealed type point wiring shall deemed to include the cost of cutting, chasing in wall by using electric cutter and making good the disturbed surface of wall by providing cement plaster and matching the surface by white wash /colour wash all as per existing finishes complete).

Supply and fix modular switch 1 module 6 amp one way ISI marked.

Supply and fix modular switch 1 module 16 amp one way

Supply and fix modular socket 2 module universal type 5/6 amp one way

Supply and fix modular socket 2 module universal type 15/16 amp one way

Supply & fix ceiling rose 65x50 mm two to three terminals complete all as specified.

Supply and laying in trench/fixed on wall/floors galvanized steel water tubing medium grade ISI marked of the following sizes incl all fittings such as bends elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps and pigs, unions etc. complete all as directed . Make Jindal/Tata/Prakash Surya/Zenith. Note :- Necessary excavation and earth work shall be measured and paid separately

S&F gunmetal globe or gate valve with iron wheel head screwed bolt ends for iron pipe of the following sizes complete all as specified and directed by Engineer-in-charge. Make : Leader/Zoloto 25mm bore

Excavation in trenches in hard/dense soil n. exc 1.5mtr wide and n. exc 1.5mtr depth for LT cable /GI tubing and getting out in Hard/dense soil all as specified.

M&L for returning, filling in including sperading, leveling watering and well ramming in layers n. exc 25 cm thick each layers in soil all as specified and directed.

M&L for removal of surplus soil to a distance not exceeding 50 mtr and deposting where directed and at a level not exceeding 1.5 mtr above the starting point all as specified and directed by Engr-in-Charge.

M/L Plain Cement Concrete Type C2, 1:3:6 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete complete all as specified.

Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified.

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups,spacers and binders complete all as specified.

RCC design M-25(using 20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified.

RCC design M-25(using 20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with hard/dense soils complete all as specified.

Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point with soils.

M&L Brick work with old size burnt fly ash bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and directed by Engineer - in - Charge .

M&L for PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection 75 mm thick incl finished even & smooth without using extra cement complete all as specified.

Cement concrete 1:3:6 type B1 ( using 40 mm crushed stone agg.) as in floor 100 mm thick as sub base finished even and smooth with out using extra cement complete all as specified and as directed

Mat finish, premium quality, joint free (edge cut), coloured/ printed Non -Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:4) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. and similar work conforming to Fe 410W Gde E250 quality B; complete all as specified and as directed.

S&F Aluminium anodized snap grid (powder coated) frame work of grid size 605x605mm including hangers 6mm dia GI (upto 1200mm long) for false ceiling including notching and preparing holes, including aluminium cleat/corner pieces and GI 4mm dia suspenders with utterfly clips, wall angle of size 24 x 24mm, main runner (teee) of size 24 x 38mm, cross tee of size 24 x 28mm, (No of suspenders shall be decided by the AGE (I) as per actual size requirement)Perforated particleboard/tiles of 12mm thick for insula-tion and accoustic purposes, as in ceilings flat or sloping 60x60 cm in size complete all as specified.

S&F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified (minimum thickness of powder coating 50 micron).

designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified

S&F powder coated anodised aluminium window and ventilator shutters, fixed type with out sash bars aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos, Tower Bolt 2 in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified (minimum thickness of powder coating 50 micron).

Excavating in post holes (or similar holes) each n.exc 0.5 Cum , getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layer n.exc 25 cm, watering, and removing surplus soil to a distance n.exc 50 mtr and making good surfaces in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft / loose soil complete all as specified and as directed.

M&L PCC 1:4:8 type D-2 (40MM graded aggregate as in sub base 75mm thick complete all as specified.