Strengthening, Renovation, Interior and extension of Ministers Quarter No.M12 at Minister Colony, Dispur, Guwahati-6

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in charge. All kinds of soil

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles above 25 mm and up to 40 mm sqm

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

2.35 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : 16.12.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 4.1.5- 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Suspended floors, roofs, landings, balconies and access platform

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) cum 8364.20

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) cum 6882.00

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Marble work metre

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.8.2.2 Granite stone slab colour black, Cherry/Ruby red Area of slab upto 0.50 sqm sqm 4679.35

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at........... fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cu......... in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 65 x 125 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chamberedframe with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), .......... dimension i.e. in depth & width of profile shall be acceptable.9.147D.1 Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) sqm

Grading roof for water proofing treatment with 22.14.1 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) cum 7510.75

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. 17.69.1 Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

Bend 87.5° 110 mm bend each 132.00

Bend 87.5° 12.42.5.1 75 mm bend each 91.80

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. b) 40 mm dia

32 mm nominal dia Pipes

20 mm nominal dia Pipes

15 mm nominal dia Pipes

Supplying fitting and fixing Johnson Zebra Roller Blinds (Combi Blackout) make and shade, design as per choice complete as specified and directed by the department at all levels.

Providing fitting fixing PVC panels for wall and ceiling(plain) with material installation including labour, carriage etc as directed and specified

Providing fitting and fixing of wooden flooring (Nobile Laminate flooring, BVG) with under layer of 6 mm materials & installation including labour, carriage etc as directed and specified.

Wardrobe of size 750mmx1950: Wardrobe of size 750mmx1950: Providing and fixing in position wardrobe unit of overall size 750mm x 1950mm x 600mm which includes following: Basic structure shall be made out of 19mm BWP ply 6mm for back and 19 mm for all sides, shelves, drawers etc.. lined with 1mm thick laminate inside and outside of BWP board / flush shutter, with Teak wood lipping at edge . Skirting shall be of 12mm thk teak wood. Wardrobe and dresser unit to have shelving unit with laminate on both sides and 2 drawers drawer unit with internal and external suraves lined with 1mm thk laminate. Shelve for safe, top shelf, s.s hanger rod, light pelmet. etc complete. The job shall include, SS runner for drawer,s.s hinges, handle for cupboards and drawers from approved Make complete in all respects

COLUMN AND WALL CLADDING WITH VENEER AND TEAK WOOD(Ht.1200mm) : 2" x 1" aluminum(of 1.3mm guage) framework, at every 2'0 x 2'0" spacing, vertically/ horizontally, extended to the nearest structural members (continuing up to slab level), to be covered with 12 mm ply on ONE side and finished in Veneer. The cladding to have a 100mm wooden skirting. Necessary cut outs to be made for sockets and other electrical points.

DOOR FRAME COVERING : Door Frame covering with plywood and veneer finished in M.M polish

Storages 1 mtrs X 1.5 mtrs to be made in 19mm thk ply as per the design detail of the drawing . The inner surface to be finished in 1mm laminate and outer surface to be finished in veneer as approved. The storage to be combination of shutters with . The overhead wll be polished finished . The price to include all hardware of Hafele make as approved. Shutters to have SS hinges.

Supplying, fitting and fixing ACRYLIC SOLID SURFACE (COURIAN) complete as specified and directed by the department at all levels

Supplying, fitting and fixing PREMIUM QUALITY WALLPAPER (ASIAN PAINTS) complete as specified and directed by the department at all levels.

Supplying, fitting and fixing PREMIUM (DOOR HANDLES) complete as specified and directed by the department at all levels.

Supplying, fitting and fixing S.S PROFILE complete as specified and directed by the department at all levels.

Supplying, fitting and fixing MDF (CENTURY) GRILL (WITH CUTTING) 18MM THICKNESS complete as specified and directed by the department at all levels.

Supplying, fitting and fixing CARPET complete as specified and directed by the department at all levels.

Providing wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed.

Supplying, fitting and fixing MODULAR KITCHEN complete as specified and directed by the department at all levels.

Supplying, fitting and fixing of BED complete as specified and directed by the department .

Supplying & installation of Sanitary Fittings including all necessary fittings in the toilet (for both floors) of Minister's Quarter No.-M-12 at New Minister Colony, Dispur Guwahati-6 as Directed by the Department.

Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) (Dyna roof sheet) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlins etc. to be measured and paid separately.)

Providing Pre Painted Galvanized Iron Sheet (PPGI) accessories (Ridges / Valley / Gutter /Flashing) at all levels including fitting and fixing self drilling, self tapping screws complete complete.

Supplying & installation of Modular Kitchen cabinet and doors made of BWP grade plywood as per IS-701, cabinets laminated inside and outside , wire basket made of 304 grade stainless steel and wooden drawers made of European style sliders at Minister Colony as Directed by the Department.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

2 X 10 sq. mm + 1 X 6 sq. mm earth wire

1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

12 Module (200mmX150mm)

1.24 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Telephone socket outlet

TV antenna socket outlet

Bell push

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.18 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair Metre 20

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B

Group C

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

Supplying., Installation, Testing and Commissioning of 1200mm sweep , BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades , 30 cm long down rod , 2 nos. canopies, shackle kit, safety rope, copper winding , Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10% remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.) , insulation resistance more than 2 mega ohm , suitable for 230 V, 50 Hz , single phase AC supply , earthing etc. complete as required.

Supplying, installation, testing and commission of the following indoor Decorative Recess mounted LED down lighter luminaries of 15W LED Recessed Luminaire Phillips complete with all accessories such as ballasat, starter etc. in the false ceiling type Armstrong/Gypsum or similar mounting with necessary support with 1.5 sq.mm P.V.C insulated S.C. copper conductor as required and as directed by the department (Phillips/Jaquar/LT/Wipro make) 15 W LED Down Light

Supplying, installation, testing and commission of the following indoor Decorative Recess mounted LED COB down lighter luminaries of 3W LED Recessed Luminaire Phillips complete with all accessories such as ballasat, starter etc. in the false ceiling type Armstrong/Gypsum or similar mounting with necessary support with 1.5 sq.mm P.V.C insulated S.C. copper conductor as required and as directed by the department (Phillips/Jaquar/LT/Wipro make) 3/6 Watt COB Light

Supply, installation, testing and commissioning of LED light fixtures suitable for any modern workspace Linea LED Strip Light Premium 50W with driver., Electronic Balast/Adaptor similar to Wipro make-Or its equipment.

Supplying including installation connection with 2 x2.5 sq.mm copper FR cable =, testing and commissioning of following post top lantern/WALL LIGHT on existing pole/structure including lamp, driver, ballast similar to ATHENA 1-1X18W LED as required

Supplying including fitting fixing of 200 mm CRISP AIR EXHAUST FAN in the existing hole on the wall of following sweeps with making necessary connection as required complete

Supplying, installation, testing & commissioning of Hi-Wall 3 star rating non ducted split type Air Conditioner of the following capacity with cordless remote complete with indoor and outdoor unit, copper pipe and electrical connection upto 5 m between the room unit and outdoor unit (1 TON CAPACITY0

Supplying, installation, testing & commissioning of Hi-Wall 3 star rating non ducted split type Air Conditioner of the following capacity with cordless remote complete with indoor and outdoor unit, copper pipe and electrical connection upto 5 m between the room unit and outdoor unit (2 TON CAPACITY0

Supplying with fitting & fixing AC Voltage stabilizer of the following specification complete including making necessary connection as approved. (SKYLAND/Vee-Dee/V GUARD/VERTAX/INDO/VENUS Make)

a) 5.0 KVA automatic input 90-280 V output 200-240 V

Supplying with fitting & fixing of Single Phase Modular AC Starter switch MODEL RANGE LEGRAND or its equivalent including making necessary connection as required.

Supplying and fitting fixing of Electric storage water heater (Geyser0 of CG SWH 3010 10 LTS ARNO NEO or equivalent make ) including necessary connection etc. as required complete

Supplying with fitting and fixing of LG Smart Television TV 42 inch. LED Backlit LCD complete including making necessary connection as approved, specified and directed by the deptt. LG Smart Television TV 42 inch LED Backlit LCD

Supplying with fitting and fixing of LG Basic Television TV 32 inch LED Backlit LCD complete including making necessary connection as approved, specified and directed by the deptt. LG Smart Television TV 32 inch LED Backlit LCD

Supplying with fitting and fixing of 581861 Mushroom Crystel Chrome E14 G9 6*MAX 42W complete including making necessary connection as approved, specified and directed by the department 581861 Mushroom Crystel Chrome E14 G9 6*MAX 42W.

POOJA ASSOCIATES(CONTRACT DIVN)