SPECIAL REPAIR TO BLOCK NO 05 OF MD ACCN ADDN ALTN TO BLDG AND PROVN OF CONNECTING PATHWAY WITH CHEQURED TILES TO CERTAIN UNIT UNDER AGE BR II AND AGE EM OF GE BENGDUBI

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches in soft/loose soil n. exc 1.5m wide and n. exc1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10sqm on plan and n.exc 1.5m in depth and getting out. in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Excavating in post holes( or similar holes) each n exc 0.50 cum , getting out,returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/ loose soil complete all as specified and directed.

M&L for sand cushioning for protection of underground cable, consolidated and compacted with clean dry sand complete all as specified and directed.

Removing excavated material (soil) n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

Removing excavated material (soil) exc 250m but n exc 500m and depositing where directed complete all as specified and directed.

M&L for hardcore of gauge n.exc. 63 mm,with broken stone and boulder, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surfaces complete all as specified and directed.

M&L cement concrete 1:5:10 type E-2 using 20mm graded brick aggregates as in sunken portion of WC etc complete all as specified and directed

M&L for PCC 1:3:6 type C2, using 40mm graded stone aggregate, as in foundation filling & mass concrete complete all as specified and directed.

M&L for cement concrete type D2, 1:4:8 using 40mm graded crushed stone aggregate as in foundations filling and mass concrete complete all as specified and directed.

M&L for Providing, cement concrete 1:2:4 type-B1 in lintels upto 1.5m clear span, cills, steps;roof padding, seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones,bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in hold fast and block filling of pressed steel chowkat including necessary form work if reqd etc complete all as specified and directed.

M&L for R.C.C, Nominal mix of 1:2:4 using 20 mm crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc all as specified and directed.

M&L for R.C.C 1:2:4 (Nominal mix) type B-1using 20 mm crushed stone aggregate for Chajjas and like etc. complete all as specified and directed.

Supply only integral water proofing compound liquid grade conforming to IS-2645 complete all as specified and directed. (Pidiproof of Dr.fixit or equivalent)

M&L for brickwork with old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for brickwork with old size fly ash bricks, straight or curved on plan to any radius as in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

Making good under cills or over arches, lintels and bressummers. including all pinning in cement mortar 1:6 when necessary complete all as specified and directed.

M&L for Cutting chases, pinning in brick walls,making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc.and making good, cutting not exc 10cm girth complete all as specified and directed.

M&L well burnt old size sub Class ‘B’ bricks, laid flat, in trenches for cable protection complete all as specified and as directed by the Engineer-in-Charge.

M&L for formwork to chullah hoods, chajjas, troughs and similar items in cluding edges complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for 2n class hardwood work sectional area exc 3sqcm but not exc 6 sqcm in Plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads complete all as specified and directed.

M&L for IInd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered,put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

S&F 25mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) area not exc. 1.5sqm each, including cutting holes for removing the hold fast,making good disturbed surfaces and removing materials from site of work complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) exc. 1.5 sqm and n.exc 4 sqm each, including cutting holes for removing the hold fast, making good disturbed surfaces and removing materials from site of work complete all as specified and directed.

M&L for Factory Made Solid PVC Moulded Door Shutter With Particle Board Core , 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) complete all as specified and directed

S&F 200mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and direcetd.

S&F 100mm Butt hinges,medium weight, cold rolled mild steel, complete all as specified and directed.

S&F 75mm Butt hinges,medium weight, cold rolled mild steel, complete all as specified and directed.

S&F Continuous (piano) hinges,mild steel, bright finish or elec?trogalvanised Width of flaps (when open) 30mm complete all as specified and directed.

S&F mild steel Helical door spring 300mm long ordinary rat tail type incl roaller & roller plate complete fixed with screws to wooden frames or with welding to steel frames complete all as specified and directed.

S&F 150mm size aluminium handle cast type complete all as specified and directed.

S&F in repairs stainless steel decorative curtain rod of 25 mm bore with wood finishes, complete all as specified and as directed.

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplescomplete all as secified and as directed

M&L for MS framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F Hard drawn steel wire fabric in available size weight not exc 4.00 Kg /sqm fixed in tank caging including welding, riveting, framing etc complete all as specified and as directed

M&L for rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to comman rafters and running rails fixed with angle cleats or other connecting plates conforming to Fe 410 W (Gde E-250) quality-A including welded to rafter,purlin complete all as specified and directed.

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 conforming to Fe 410 -W (Gde E- 250) quality A complete all as specified and directed.

M&L for 1.25mm thick pressed steel door frame of size 165mm x 60mm with one or more rebates including necessary , hinges, lock strike plate, fixing lugs etc complete as specified.

M&L for 1.25mm thick pressed steel door frame of size 105mm x 60mm with one or more rebates including necessary fixing lugs , hinges, lock strike plate etc complete all as specified and directed.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors,windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary fittings and filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed.

M&L for anodised aluminium snap grid (SIZE-605x605MM) frame for false ceiling including hangers 4mm dia GI wire up to 1200mm high adjusting level fixed to roof framed structure complete all as specified and directed.

S&F Pre- painted coloured trapezoidal profiled Galvalume/ Zincalume sheet with min thickness 0.50mm TCT confirming to IS - 513(AZ-150 GSM, Al Zn allay metalic coating with 550 Mpa yield stress as per AS-1397) as in roof covering/cladding to wall, fixed with self tapping screws colour exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron polyster back coat applied over 5 micron primer, all fixed with galvanized self drilling self tapping fastner (12-14 x 55 with EPDM seals) complete all as specified and directed.

S&F Pre- painted coloured plain sheet Galvalume/ Zincalume sheet with min thickness 0.50mm TCT confirming to IS - 513(AZ-150 GSM, Al Zn allay metalic coating with 550 Mpa yield stress as per AS-1397) as in roof covering/cladding to wall, fixed with self tapping screws colour exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron polyster back coat applied over 5 micron primer , all fixed with galvanized self drilling self tapping fastner (12-14 x 55 with EPDM seals) complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F 4 mm thick designed pre painted Non asbestos fiber cement building boards, fixed or laid /inserted to timber /GI /Aluminium frame-work with screws as in ceiling complete all as specified and directed.

M&L 18/19mm thick Pre laminated exterior grade both sides laminated with decorative choice laminations fixed with screw to timber frame as in cupboard shutter, shelve, kitchen cabinet etc complete all as specified and directed

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in skirting,kitchen plateform,dado steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including poining in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite over and including 15mm thick bedding layer in cement mortar 1:4 including grinding and polishing complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 (Using 40mm graded crushed stone aggregate) as in plinth protection finished even and smooth using extra cement.Joints to be given at every 3m interval and corners of buildings and fitted with bituminious mastic or equivalent filler complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 (Using 40mm graded crushed stone aggregate) as in floor/ sub base of floor complete all as specified and directed.

M&L for 100mm thick PCC 1:3:6 type C2 (Using 40mm graded crushed stone aggregate) as in sub base of floor/ floor path complete all as specified and directed.

Roughening the surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust, etc and brushing neat cement slurry with 3.0kg of cement per sqm complete all as specified and directed,

Dismantling of floor, hearth or wall tiling / Paving Blocks including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed.

Dismantling timber scantlings 40 sqcm and over in section, in framed section any position like trusses, rafters, purlins etc. complete all as specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

Taking down existing un-sreviceable water proofing treatment from roof slab and slab and cleaning the roof by wire brush and removing WPT felt beyond the MOD premises etc. cement plaster on brick or stone walls, etc.complete all as specified and directed.

Supply only 4mm Sheet glass,plain, ordinary quality, in squares n. exc 0.5 sq. m each complete all as specified and directed.

Supply only 4mm Sheet glass, plain, pin headed type in squares n. exc 0.5 sq. m each complete all as specified and directed.

M&L for preparation of old painted wood/wooden surface of any description over 10cm width or girth and applying one coats of synthetic enamel paint (1st grade quality) complete all as specified and directed.

M&L for preparation of untreated new wood/wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed.

M&L for one coats of synthetic enamel paint on old treated steel surfaces of any description over 10cm in width or girth including preparation of surfaces complete all as specified and directed.

M&L for two coats of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth including preparation of surfaces complete all as specified and directed.

M&L for 40mm dia GI pipe Light grade with all necessary fittings laid in trenches, fixed to wall/pole/under road/floor etc for cable protection complete all as specified and as directed.

S&F medium grade galvanized steel tubing with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified and directed.

S&F medium grade galvanized steel tubing with all fittings & fixed complete to walls & ceiling or laid in floors 25 mm dia bore pipe (including in short length) complete all as specified and directed.

Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 15 mm dia bore complete all as specified and as directed

Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 20 mm dia bore complete all as specified and as directed

Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 25 mm dia bore complete all as specified and as directed

Dismantling water tanks and removing to store exc 250 ltr but not exc 500 ltr capacity complete all as specified and as directed

S&F rotational moulded PVC water storage tank 500 ltrs capacity conforming to IS-12701(1989) cylindrical vertical type double-layered with closed top (thereated) including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I etc completge all as specified and directed.

Supplying and laying of CPVC pipes outer diameter 20mm SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified and directed.

S&F ball valves for 20mm bor dia of pipe high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S&F in repair PVC connections pipe ,15mm dia size with PTMT nuts of length 450mm complete all as specified and directed.

S&F 75mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F 110mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F in repair 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends,diminishing pieces or tapers with rubber ring joints any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends, diminishing pieces or tapers with rubber ring joints any radius complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends provided with access door with rubber ring joints any radius complete all as specified and directed.

S&F 75mm bore PVC (SWR) branch piece,single (single Y) equal or unequal complete all as specified and directed.

S&F 110mm bore PVC (SWR) branch piece,single (single Y) equal or unequal complete all as specified and directed.

S&F PVC (SWR) floor trap 75mm dia , plain with grating including jointing with solvent cement to waste pipe complete all as specified and directed.

S&F in repair sinks made of stainless steel 01mm thick kitchen or laboratory with plugs, washers and wastes;including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets, 40mm CP waste fitting and waste pipe and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed

M&L for XLPE insulated GI wire/Strip armoured Electric power cable (Heavy duty) with stranded Aluminium conductor 1100 Volts grade, cross sectional area 16Sqmm 2 core laid in trench/pole/on wall completer all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings,dressed stonework and precast concrete articles complete all as specified and directed.

Demolition of cement concrete( un-reinforced) in ground floor and paving n.exc 15 cm thickness( below or above ground level) complete all as specified and directed.

Demolition of Concrete un- reinforced of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of cement concrete (reinforced ) of Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work including removal complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings incl ridges, hips and valley gutter complete all as specified and directed.

Dimantling of Asbestos cement (corrugated,semi corrugated, etc.) sheets in roof coverings including ridges etc complete all as specified anddirected

Dismantling wall and ceiling board( fiber, pulp, insulation, etc.) or insulation board/slab/ blankets, any thickness, including cover fillets complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, partitions,windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make onforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. Note : (i) Weight of Aluminium sections as per actual or as per IS or as per Manufacturer which over is less, shall only be considered for payment. (ii) Cost of all the items/ accessories required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes and particle board shall be measured and paid separately under respective items. (iii) The accessories required for partition as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered and no extra cost will be paid.

M&L for machine cut kota stone in riser, dado, steps, skirting etc 20-25mm thick of size over and including 15mm thick cement rendering in cement mortar 1:6 laid & jointed with grey cement slurry mixed with pigment to match the shade of slab including granite ( mirror) polishing complete all as specified and directed.

M&L for Glazed ceramic tiles coloured 300mmx 450mm , 6 to 7 mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surface etc complete all as specified and and as directed

M&L for Non Skid ceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes etc complete all as specified and directed

M&L for Non Skid ceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm as in dado/skirting etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including rendering layer 10 mm thick in cement mortar 1:3 etc complete all as specified and directed

M&L for Non Skid ceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.38sqm as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes etc complete all as specified and directed

M&L for pre polished coloured cement concrete chequred tile 300x300x25mm with grey cement and no pigment of approved quality size 300X300X 25mm thick on floors over and including 15 mm thick screed bed cement mortar 1:6 set and jointed in neat cement slurry and pointed with colour to match the tiles complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in two layers 10mm +5mm in cement mortar 1:4 on external surfaces of brick work or concrete surfaces with using WPC finishing the surfaces even and smooth without using extra cement complete all as specified and directed. Note:- WPC will be measured and paid separately under respective item of this schedule.

BLANK

M&L for 5mm thick rendering in cement mortar 1:3 over/soffit of chajja/ceiling, finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered surface of walls with 2mm thick wall care putty in two coats and and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc complete all as specified and as directed

M&L preparation of new plastered surfaces of wall and applying two coat of cement base paint over a coat of cement wash complete all as specified and directed.

M&L for preparation of new surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces over 2mm thick wall care putty complete all as specified and directed.

M&L for preparation of old surfaces by complete removal of existing treatment and applying and Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 02mm thick wall care putty complete all as specified and directed.

M&L for preparation of new undecorated surface of ceiling and applying three coats of white wash complete all as specified and directed.

M&L preparation of old plastered surfaces of ceiling and chajjas and applying one coat white wash complete all as specified and directed.

M&L for newly plastered surface of wall and appying two coat of white or tinted oil bound distemper over one coat of alkali resistant priming primer including 02mm thick wall care putty complete all as specified and as directed.

M&L for preparing of old plastered surface of wall by complete removal of existing treatment and applying 2mm thick wall care putty on wall including preparation of surface and applying two coat of white or tinted oil bound distemper over one coat of alkali resistant priming paint etc complete all as specified and directed.

M&L for newly plastered surface of wall and appying two coat of white or tinted oil bound distemper over one coat of alkali resistant priming primer including 03mm thick Birla/Asian wall care putty complete all as specified and as directed.

S&F 4.0mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and directed.

S&F CPVC brass elbow 20mm complete all as specified and directed.

S&F CPVC brass Tee 20mm complete all as specified and directed.

S&F CPVC brass fitting MTA 20mm complete all as specified and directed.

S&F in repair bib tap fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and directed.

S&F in repairs 15 mm bore pillar taps fancy type (long neck) cast copper alloy with hot & cold mixture chromium plated screwed down high pressure with or without letter hot or could with long screwed and shanks and fly nuts screwed for iron pipes complete all as specified and as directed.

S&F in repair fancy type, chromium plated stop valve/ angle valve cast copper allow screw down high pressure with crutch or butterfly handle screwed both end form iron pipe or for union and fixed of size 15mm dia complete all as specified and directed.

M&L for 40mm thick cement concrete type B0(1:2:4) (Using 12.5 mm graded crushed stone aggregates) admixed with admixture conplast WL Xtra (of make FOSROC or equivalent brand of other manufacturer) at the rate of 125ml/50 kg bag of cement and vergin ploypropyle complete all as manufacturer instruction and directed

M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:4 on concrete surface mixed with water proofing compound as per manufacture instruction etc complete all as specified and directed. Notes : WPC shall be measured and paid seperately under respective item of this schedule.

S&F in repair chromium plated shower roses 125 mm size with or without swivel joints of standard size including fixing to 15mm steel pipe or union complete all as specified and as directed.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level 10 ltr capacity , white, with inlet, ball valve, float and handle including brackets and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified and directed.

S&F in repair Health faucet (ABS Body) mild steel CP suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook incl making connection and fixed in position complete all as specified and directed.

S&F in repair Vitreous china WHB 550x400mm size white flat back with brackets incl cutting or pinning ends of brackets (including waste pipe) incl Waste coupling of PTMT (32 mm dia) (half or full threaded) (Minimum weight 32mm 45gms/40mm-60 gm complete all as specified and directed.

S&F in repair Vitreous china coloured wash down water closet pan (Padestal Pattern), including connection to flush pipe, 'P' or 'S' trap, with fixing bolts PVC seat cover with chromium plated mild steel hinges device (excluding flushing cistern and flush pipe), and making good to dismantled/damaged tiling floor complete all as specified and directed.

S&F in repair tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and directed.

S&F 0.63 mm thick stainless steel plate rack of overall size 24"x36"x10" of standard quality and shape complete all as specified and directed.

S&F in repair Low density polyethylene (LDPE) pipes bore of pipe in 32mm of pressure rating 6 kgf/sq. cm complete all as specified and directed

Dismantling of stone slabs and tiles of any description or thickness in floors, approachs, dado/Partitions etc complete all as specified and as directed

S&F 2nd class hard wood 35 mm thick made glazed and skeleton shutters open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) kiln seasoned and chemically pressure treated complete all as specified and as directed

M&L for waterproofing coating by providing and applying Fostoc Brushbond Roof Guard of FOSROC or equivalent of SIKA/STP , a single component High build fibre Reinforced Acrylic Waterproofing render for roofing system applied by brush, at three coats at minimum dry film thickness of 1 mm, cured by reaction with atmospheric moisture to give a tough elastomeric waterproof membrane complete all as per manufacturer specification, specified and directed. Solid Content - 70%, Tensile strength ASTM D 412-1.10 Mpa, Elongation ASTM D12-100%, Resistance to ageing due to - 1000hours, UV radiation ASTM D4587 E - No Change, Rapid Chloride Penetration ASTM c 1202 - Very low, Pull off adhesion ASTM D541 - 0.92 Mpa, Resistance to Algae growth ASTM D 5589-97 - Passes, Zero rating, Permeability (mm) (BSEN 12390 part 8) -n 5.0, Water vapour transmission (ASTM E 96) - 6.0g/m2 h

Taking down of Old MCB DB / control box/main switches any type any size including MCBs and separating the serviceable MCB DBs and MCBs for reuse at site complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc as per existing specification complete all as specified and directed.

M&L for concealed point wiring with FRLSH PVC insulated unsheathed multistranded copper conductor cables 1100 Volts grade of 1.5 sqmm size alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable 1100 Volts grade of 1.5 sqmm size through and including 20 mm dia (medium grade) rigid non metallic PVC concealed conduit terminated in and including pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type with 3mm thick bakelite sheet cover for fixing of switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good to disturbed surface complete all as specified and directed for the followings: -

One light point/ Bell/ one fan point controlled by one switch 5 Amps

One 3 pin socket outlet, 6 Amp on the same board with other switches

One 3 pin socket outlet, 6 Amp independent

One light point controlled by two 2- w a y switches

M&L for concealed point wiring with FRLSH PVC insulated unsheathed multistranded copper conductor cables 1100 Volts grade of 2.5 sqmm size alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable 1100 Volts grade of 2.5 sqmm size through and including 20 mm dia (medium grade) rigid non metallic PVC concealed conduit terminated in and including pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type with 3mm thick bakelite sheet cover for fixing of switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good to disturbed surface complete all as specified and directed.

S&F Switch piano, flush type single pole, one way 6Amp complete all as per specified and directed.

S&F Switch piano, flush type double pole, one way 6Amp complete all as per specified and directed.

S&F Switch piano, flush type single pole, one way 15Amp complete all as per specified and directed.

S&F Bell push, flush type, 6 amp complete all as per specified and directed.

S&Fcall bell ding dong , AC, 230 volts, single pole complete all as per specified and directed.

S&F Socket outlet 2 in 1, 3 pin, 6 and 16Amp flush type complete all as per specified and directed.

S&F Socket outlet 2 in 1, 5 pin, 6 Amp complete all as per specified and directed.

S&F Sheet metal enclosure powder coated for MCB DB double door single pole & Neutral 4 way with 200Amp rated common bus bar at incomming complete all as specified and directed.

S&F Sheet metal enclosure for MCB DB double door 240V single pole & Neutral 12 way with common bus bar at incomming end complete all as specified and directed.

S&F Sheet metal enclosure for MCB DB double door 415V Triple pole & Neutral 4 way with common bus bar at incomming end complete all as specified and directed.

S&F Ceiling rose, 3 phase/PVC/ polycarbonate, isolated body complete all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified and directed.

M&L for sub main wiring with 2 run of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm alongwith one run of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm as earth continuity conductor drawn through and including PVC conduit complete all as specified and directed. Make :Polycab/Finolex/KEI. Note: For concealed sub-main wiring cutting chases will be included in quoted rate)

Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) TPN 40 to 100 AMP in the DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing 240V, 10KA 'C' curve SPN miniature circuit breaker (MCB) 40 to 63 Amps, in the MCB DB complete with connection testing and commissioning. complete all as specified and directed.

Supply and fixing 240V, 10KA 'C' curve single pole miniature circuit breaker (MCB) 6 to 32 Amps, in the MCB DB complete with connection testing and commissioning. complete all as specified and directed.

S & F for wall mounted LED tube light fitting 10 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and directed.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired and necessary mounitng arrangements and provision of 1.5 sq mm three core copper dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed.

S&F in replacement Decorative wall light fixture, brushed nickel finish, suitable for 9 Watt LED lamp (B22) including 9/10W LED Bulb etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexiblecopper conductor cable with suitable sizecomplete all as specified and directed.

S&F in replacement light fitting,1x10W LED bulk head luminaries IP65, Min-50,000 burning Hrs, Diffuser made of high grade polycarbonate, High pressure die cast aluminium housing, CCT-5700K, 240 volt complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V,50HZ.

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and directed.

Taking down ceiling fan/ exhaust fan of any sweep, keeping with safe custody and refixing the same with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal over hauling the fan complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230V,1200 mm sweep, 100% copper wound motor, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. Make: Usha/Bajaj/HAVELLS

S&F in replacement 36W LED Square Type 2' x2' recessed mounted downlighter including suitable driver, cutting of False ceiling as required and all accessories for fixing arrangement complete all as specified and directed.

Supply and fixing wall fans complete with blades, electronic regulator and acessories, 230V, 400mm sweep. Five star rated complete all as specified and directed. Make: Bajaj/Havells/Usha

S & F for energey efficient exhaust fan of 300mm sweep made of metal body ventil Air-DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as directed by GE.

S & F for energey efficient exhaust fan of 250mm sweep made of metal body ventil Air-DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as directed by GE.

Supply, installation and testing of electric water heater storage vertical type, BEE 5 star rated, 25 ltr capacity 240 volts 50 Hz comprising of high wattage heating element of 2 KW for instant heating, extra Mild steel with Glass lined coated inner tank, rust & shock proof ABS outer body, non-ferrous pressure plate with & including provn of 04 Nos grouting bolts suitably flushed to wall or any other surface including electric connection with 3 core PVC insulated, sheathed, stranded copper conductor cable/ flexible chord and one No 15 amps 3 pin plug top complete all as specified and as directed. Make: Havell's/Bajaj/CG//Racold.

Taking down of old Submain wiring upto10sqmm any type including batten/ conduit/ casing at any indicated situation complete all as specified and directed.

M&L for earthing complete with galvanised earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground (earth pit not less than 2.25 mtr below normal ground level with top edge of the plate not less than 1.50 mtr below normal ground level connected to galvanised lead lead wire 4.0 mm dia by means of bolts, nuts and washers and check nuts of galvanised iron or steel GI earth strip protected by 40 mm medium grade galvanised iron pipe including of 20 mm dia medium grade GI water tubing sheet metal 4mm wire mash funnel, charcoal or coke and common salt in paint and testing on completion all as shown on electrical plate No.3 of SSR Part-I. including taking out unserviceable one and necessary earthwork complete all as specified and directed.

(Note : The Scope of Work contained in 'Sch of Credit' amounting to Rs. 86,218.00 (refer Tender Srl Page No 33). The Quoted sum shall be arrived at after deducting the amount of “Sch of Credit” from the total amount of the ‘BoQ’

SRI A B SEN (BID ID -3358594)

M/S BISWAJIT BHATTACHARJEE (BID ID -3361567)

TECHNOSOFT (BID ID -3358699)

BISWAJIT SAHA (BID ID -3361580)

M/S SANKAR BHATTACHARYA (BID ID -3358766)

D BHATTACHARJEE AND CO. (BID ID -3361624)

NAYAK BROTHERS (BID ID -3362462)

GAYATRI BUIDERS (BID ID -3362551)

REEJU BANIK (BID ID -3360703)