Construction of Labour Shed at Harmu Chowk under ward No 26

Labour for cleaning the work site before and after work etc.

Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance up to 50 M. including all lifts, levelling, ramming the foundation trenches removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/I.

Extra for earth work in hard soll as per specification and direction of E/L (Vide classification of soll item B)

Filling in foundation trenches and plinth in layers not exceeding 150 mm thick well watered ,rammed,fully compacted and fine dressed with earth obtained after cutting with lead a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I ( Mode of measurement compacted volume )

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150 mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification & direction of E/I.

Providing designation 75B one brick flat soling –do-- --do--

Providing and laying position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level. PCC 1:2:4

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level1:1.5:3 (1 Cement : 1.5 coarse sand zone(III): 3 graded stone aggregate 20mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering shuttering, finishing and renforcement-all work up to plinth level RCC 1:1.5:3

Reinforced cement concrete work in wall , inluding attached pilaster, buttresses, plinth and string coarse, fillets,columns,pillars-----do-----do-------E/I RCC 1:1.5:3

Reinforced cement concrete work in beams, suspended floors, foors having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staicases and spiral stair cases above plinth level up to floor five lvevel, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (Zone-III) : 3 graded stone aggregate 20mm nominal size).

Providing Tor steel reinforcement of 8mm dia rods bars as per approved design and drawing –do-- --do—TMT Fe 500 (only valid for SAIL and TATA steel,JSPL,Electro steel Ltd and Vizal steel) +Providing Tor steel reinforcement of 10mm,12mm and 16mm dia bars as per approved design and drawing –do-- --do—

12mm and 16mm

Brick work in Foundation (1:6) -do-

Brick work in Superstructure (1:6) -do-

Brick work in Superstructure (1:4) -do-

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces),excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.80 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete Ridges plain (500 - 600mm)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with:

Providing and laying 6mm. precast white glazed tiles in walls over 12mm. cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specification and direction and of E/I. With commercial grade colour tiles.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 600 mm

Centering and shuttering including strutting,propping, etc and removal of form for foundation, footing, bases of column etc

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing 12mm Thick cement plaster (1:4) -do-

Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 itr/10 sqm over and including priming coat of exterior primer applied @ 0.90

Providing and fixing 1 mm thick M.S. sheet door with frame of 40 * 40 * 6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40 * 40 * 6 mm for diagonal braces

Providing two coats of synthetic enamel paint of approved shade and makeover steel surface -do-

Carriage of Materials Sand (Lead Upto 42 km)

Local Sand (Lead 18 KM)

Stone Chips (Lead 15KM)

Bricks 08 KM

Earth (Lead 01 KM)

Flat Brick Soling Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per bullding specification and direction of E/I

CONCRETE WORK PCC Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth grade level: 1:12:3 (1 Cement: 1½ coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Brick Work Foundation And Plinth Provided designation 75A Brick work in C.M.(1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2.0 to 2.50 including providing 10mm thick mortar joint cost of screening material raking out joint to 15mm depth curing curring taxes and royallity all All complete as per building specification and direction of E/I.

Providing designation 125 mm. thick reinforced designation on 75 A brick work in C.M (1:4) In superstructure with approved quality of clean coarse sand of F.M 2 to 2.5 Including the cost of screening, carrlage of materials, scaffolding, raking out jalnts to 15 mm. depth, curing taxes and royalty (but excluding the cost of reinforcement) all complete job as per building specification and direction of E/1.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size).

Providing 12mm thk cement plaster(1:4) with clean coarse sand of F.M.including screening,curring with all lead and lift of water scaffolding, Laxes and royality all complete as per building specification and direction of E/I.

Providing 1.5 mm. cement punning including curing carrage of water withall leads and lifts as per building specification and direction of E/I

Reinforcement Providing Tor steel reinforcement of 8mm dia rods as per approved -do- TMT Fe 500 (Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd. Bokaro and Vizag (RINL)

Providing Tor steel reinforcement of 10mm..12mm & 16 mm. dia bars as per approved design and drawing-do--do-

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Circular shape 560 mm internal diameter.

Making soak pit 2.5 m diameter 3.0 m deep with 45x45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design with common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size GI box and earthing the point etc as required. Group A.

Circuit / Submain Wiring Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required. 2x2.5 Sqmm + 1x2.5 sqmm earth wire

4x6 Sqmm + 2x6 sqmm earth wire

Switch / Socket S/F Piano type switch / socket :- Supplying and fixing of following sizes of PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. 5/6 amps, one way switch

3 pin 5/6 amps, socket outlet

Power Plug Point S/F lpower plug point with piano type accessories :- Supplying and fixing sutiable size G.I./PVC box on surface or in recessed with phenolic laminited sheet cover in front including providing and fixing 6 pin , 15/16 amps socket outlet and 15/16 amps piano type switch connection , painting etc, as requried.

Celling Rose S/F Ceiling Rose: Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooen block including connection etc as required. Make :- Anchor / Kona / Kany

Batten Holder S/F Batten / Angle Holder: Supplying and fixing batten / angle holder including connection etc as required.

Ceiling Fan (1200 mm) ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq. mm. FRPVC insulated,copper conductor,single core cable etc, as required.

Supplying Ceiling Fan 48" (1200mm)

Fan Regulator S/F Modular type electronic fan regulator :- Supplying and fixing stepped type electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Exhaust Fan ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

Supply 9" (230mm) metal exaust fan

Disconsector S/F rewireable double pole / TP&N switch disconnector:- Providing and fixing following capacity doble pole / TP&N sheet metal switch disconnector fuse unit in existing metal board with rewireable type fuses, including drilling holes in metal board, making connections, etc as requried. 32 amps, double pole

S/F S.P. MCB DB : Supplying and fixing following way single pole nutral , sheet, MCB dstribution board , 240 volts ,on surface/recess, complete with tinned copper busbar,nutralbusbar, earth bar,din bar, detachable gland plate,interconnection, phosphate and powder painted including earthing etc.as required.(But without MCB/RCCB/Isolator). 6way,single door

Bulb 15/16Watt LED Bulb

Supplying all materials, labours and tools and equipment for drilling 200 X 165mm dia. X 125 Mtr. bore well in all kinds of soil and rock in urban area for installation of pumps set with Hydraulic DTH Rig Machine, all complete including drilling rig, Air Compressor and equipments, as well as fuel, lubricants and cost of transporation of rig machine and over vehicles up to the site etc. all complete job as per specification and direction of E/lc. From 0-50 Meter

From 51-125 Meter

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200mm nominal size dia

Supplying all materials: labours, tools & equipments for fiting & fixing 200mm dia MS cap over casing pipe etc. all completes job.

Cleaning flushing and developing of drilled hole for testing the discharge of water development of bore well by continuous flow of water by using heavy compressor up to satisfaction of E/l. to get uninterrupted flow of water free from sand and soil etc.

Supplying of 150mm dia 02.00 H.P. (ISI Mark) KSB/Kirlosker/CRI/V-guard Submersible Motor Pump sets comfirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50Hz, A.C. supply with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non returned valve shall be provided with pump. 3 meter submersible copper in single/double run shall be provided with each pump.(up to 20 stages) Supply rate should be increased by Rs 200/-per stage for pump with more than 20 stages.

FR PVC insulated 3 core 4 sq. mm. copper wire

Supplying of 32mm Submersible Pipe of standard make Ashirwad/Raksha/Prince/Gupta or any equivalent make for above requirement.

Supplying of 02 Nos. clamp, Band, Adopter, Bore Cover etc. as required for above work.

Supplying & Providing Rope of required size & tape.

Supplying & Fixing of BCH Make or Equivalent Panel Board with all accessories & Iron Box with Angle Stand and its fixing as per direction of E/l.

Installation Charges for Lowering of Motor Pump.

Supplying and of 10.0sq.mm Alluminium cable ISI mark as per specification and direction of E/l. (for connection from main line to electric Meter.

Common Bath & Toilet WC Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I. 'p' trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware footrest to be fixed in floor 15mm C.I. body brass spindle stop cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and dirction of E/I. 580mm long - With 12.5 Liter Low Level P.V.C. costern

E.W.C Urinal Basin Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthen ware urinal of Hindustan 'Parry' or any other approved I.S.S. make with 5 litres capacity C.i. automatic flusing cistern of reliance for any other I.S.S. approved make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grams, 15mm PVC/Alkthene pipe 450mm longwith brass coupling at both ends and doing plumber joints including priming coat of red oxide, cutting wall and floor making good the same etc. all complete as per specification and direction of E/I. Flat back or standard corner (600mm x 350mm)

Hand Wash Basin Supplying fitting and fixing viterous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32mm C.I. brass waste, 15mm dia C.I. body brass spindl stop cock approved quality of weight not less than 30 grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Towel Rail Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I. C.P. brass towel rail 20mmx600 mm with brackets container etc.

Soap Dish Container Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I. C.P. brass shoap dish container medium quality with screw and hinges etc.

Mirror Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I. Mirrors of 6 mm thick plate glass bevelled edge mirror Including C.P brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror. 600mmx450xsize

Floor Trap Supplying and fitting fixing H.C.I fittings of approved makes confirming to 1.5.5 1729 Including supplying nails and bobines lead and yarn from making lead caulked joints Including earth work or providing scaffoldig as the case may be complete as per specification and direction of E/L

Stop Cock Providing and fixing brass /C.I. stop cock approved quality all complete as per specification and direction of E/I. BRASS STOP COCKE- 15 mm dia

BRASS STOP COCKE- 20 mm dia

Pillar Cock Providing and fixing 15 mm sizes C.P. brass pillar cock ( weight not less than 350 gms) C.I body brass spindle pillar cock of approved quality as per specification and direction of Enginer-in Charge. C.I body brass spindle

BIB Cock Providing and fixing male ended 15mm dia brass bib cock of approved quality (Wt. not less than 350 gms.) with extra socket all compere as per specification and direction of E/I.

Pipe Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal dia Pipes

20 mm nominal dia Pipes

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110mm diameter (for rain water)

1000Lt. Tank Circular Tank

Good & Service Tax (GST)

Labour Cess