Day to day maint including Repair Replacement to joinery flooring sanitary fitting internal water supply and connected works at Sewar fort Bharatpur

Amount

Taking down cement plaster of any description etc including racking out joints,hacking for key, scrubbing down with water all as specified

Rendering 15 mm thick in CM (1:4) on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing complete all as specified & as directed

Ditto as above item no 2 but in CM (1:6) finished even and smooth without using extra cement complete all as specified & as directed

M&L for rendering 10mm thick in two layer (5+5)mm using premixed polymer modified cement plaster of approved make - Mix the powder with clean, drinkabie water in the ratio 5-7 liters of water to 20 kg of powder. Allow the mixture to stand for 10 minutes then mix again before applying. Best results are obtained with mechanical mixing, i.e. mixing drill and 20 liter bucket. When applying to non-porous surfaces and when extra durabillity an hardness is required add 1 liter of Acrybond chemical per 20 kg Polymer modified cement mortar. on Internal/External surface of brick work, reinforced cement concrete finished fair & even as manufacturer’s application instructions andcomplete all as specified and directed. Note:-(1) Before apply to concrete, cement render, brick and block surfaces that are clean and firm, free of dust, release agents, grease, wax, paint and other contaminants. Wet the substrate prior to the application of the mixture. (2) When applying more than one layer the preceding layer must be completely dry before applying the next

M&L for rough cast plaster mixture consisting of fine M-crushed washed sand mixed with coarse aggregate(6 to 10 mm) and cement in ratio of 1:1:1 over and in plastic state including 10 mm thick rendering in cement and M-crushed washed sand mortar 1:3 on fair faces of bricks masonary or concrete surface of wall complete all as specified & as directed

M&L for Rendering 10 mm thick in cement and sand mortar 1:3 on fair faces of cement concrete surfaces of ceiling of chajjas/roof protection etc including finishing the surface even and smooth without using extra cement complete all as specified and as directed.

M & L Preparation of new plastered or un plastered surface of wall including cornices, pilasters etc by brooming down and applying two coats of distemper oil emulsion white or tinted over a coat of wall primer wash with hand roller complete all as specified and as directed

M&L Preparation of newly plastered surfaces of ceiling & applying three coats of white wash complete all as specified and as directed

M & L Preparation of old decorated plastered or undecorated plastered surface of wall including cornices, pilasters etc by brooming down, steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of white wash complete all as specified and as directed.

Ditto all as per Srl item No 09 here in above but applying one coat of white wash on ceiling complete all as specified and as directed

M&L for Complete removal of existing treatment,washing, rubbing down and stopping of distemperd and painted surface of old surface by Electric Rotary grinder including brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorscent salts and trading oil and greasy spots of Wall Surface removing of nails, making good holes , cracks etc , cleaning of floors , glasses, joinery of drops and splashes incl all arrangement necessary for execution of work. complete all as specified and as directed

M&L for Two coats of oil emulsion distempering white or tinted using hand roller over one coat of one coat of water based white akali resistant priming paint , over 1mm thick wall care putty on Wall Surface including sand paper gentle rubbing to obtain smmoth surfaces, including all necessary arrangement for execution of work. Complete all as specified & as directed.

M&L for Two coats of Apex Weather Proof Exterior emulsion (Water Based 100% Acrylic ) or approved equivalent grade paint using hand roller over one coat exterior grade wall primer on cement plaster,concrete ,exterior ceiling etc ,including surface to be painted shall made free from any loose paint ,dust,grease, fungus,algae, moss, shall got be removed .All materials shall be Asian /Nerolac/ Berger/ Dulux Make .Color & Pattern /Color Combination of the paint shall got approved from GE. Complete all as specified & as directed.

M&L for 2-3 mm thick JK Cement wall Max Putty on Wall Surface including sand paper gentle rubbing to obtain smmoth surfaces & Mixing is done by using mechanical stirrer including all necessary arrangement for execution of work. Complete all as specified & as directed.

M&L for Two coats of Cement Base Paint using hand roller over one coat of water based white pigmented akali resistant priming paint for external wall after thourughly wetted surface to ensure better sticking including sand paper gentle rubbing to obtain smmoth surfaces, including all necessary arrangement for execution of work complete all as specified and as directed

M&L for Preparation of old decorative concrete, plastered/ un-plastered surface of wall including cornices, pilasters etc by brooming down, steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots removing nails and filling small holes by putty and rubbing surface by sand paper to prepare the surface and applying one coat of cement based paint using hand roller of approved colour complete all as specified and as directed.

M & L Preparation of old distempered surface of wall including cornices etc by brooming down, steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots removing nails and filling small holes by putty and rubbing surface by sand paper to prepare the surface and applying one coat of distemper oil emulsion using hand roller white or tinted complete all as specified and as directed.

M&L for one coats painting with synthetic enamel paint to old wood or wood based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface including all preparatory work complete all as specified & directed

M&L for one coats painting with synthetic enamel paint to old steel or steel based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface complete all as specified & directed

Demolition of brick masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings,dressed stone work and precast concrete articles all as spd and directed.

M&L Brick work with sub class 'B' old size bricks bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6. Complete all as specified & as directed.

Ditto Item No 21 but except bricks.

Taking down chowkats or frames n. exc 1.5 sqm each with shutters (without taking off shutters from the frame). Complete all as specified & as directed.

Taking down chowkats or frames exc 1.5 sqm but n exc 4 sqm each with shutters (without taking off shutters from the frame). Complete all as specified & as directed.

Taking down shutter of any description area exc 1 sqm and n. exe 2 sqm. Complete all as specified & as directed.

S&F for 30 mm Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35 mm thick 2nd class hardwood( hollock ) factory made plain framed, panelled shutters (any No. of panels) with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces size of members as per IS 1003 PtI. Complete all as specified & as directed.

S&F 35 mm thick 2nd class hardwood ( hollock ) factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc.( without sash bars ), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified in SSR Part I. Complete all as specified & as directed.

S&F steel ventilator with top hung shutter including hinges,steel peg stay, handle complete specified & as directed.

S&F for sollid PVC door frame of size 50mmx47mm made out of 5mm plain colour pvc sheet reinforced with m.s. squre tube complete all as specified and directed.

Supplying & fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heatmoulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. Complete all as specified & as directed.

M&L for rolled mild steel framed work such as grill grating etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors , laddres, door gate frame, framed baliusters, walk ways, railing , frame work of water tank and similar work conforming to Fe-290, Gde-E-165. Complete all as specified & as directed.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position complete specified & as directed.

S&F 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified & directed.

S&F 150 mm long mild steel barrel tower bolts stove enameled black with bright bolt (ISI marked) complete all as specified & directed.

S &FMild steel presses steel bow handle oval type stove enameled black of size 150 mm (ISI marked). Complete all as specified & as directed.

S&F MS sliding door bolt, plate type, 300mm long, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts & nuts, 4 on bolt plate and 2 on staple plate and fixed.complete all as specified & directed

S&F extruded aluminium alloy handle 150mm size fabricated type anodised, ISI marked . Complete all as specified & as directed.

S&F Aluminium anodised barrel tower bolt 150mm long of extruded section and fixed. Complete all as specified & as directed.

S&F 100 mm Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, typeB-11. complete all as specified and as directed

Factory made steel window with side hung shutteers including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded complete all as specified & directed

All as per item No 42 above but without glazing bars. (Note :- Mild steel wire cloth shall be measured and paid separately under respective items) complete all as specified & directed

M&L dismantling floor,hearth or wall tiling including cement mortar bed(but not backing) , removing serviceable tiles to store and rubbish off the premises all as specified & directed

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 300mm x 200mm, 7mm thick over and including 15 mm thick rendering in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed. Complete all as specified & as directed.

Providing and laying double charged vitrified floor tiles in 600X600mm sizes 9-10mm thickness,in required pattern, with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all shades, laid on 15 mm thick cement mortar 1:4 , jointing with grey cement including grouting the joints with white cement and matching pigments etc., complete all specified & as directed

M&L Glazed ceramic Digital tiles ,matt/glossy finish in vertical surface,in required combination of themes, area of each tiles exceeding 0.9 sqm but not exceeding 0.27 sqm 7-8 mm thick thick set and jointed in neat cement slurry, over 15mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for Coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm bur not exceeding 0.16 sqmm, over 10 mm thick screed bed in CM 1:4 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match for repair & matched to existing floor tiles in patches. Complete all as specified & as directed.

M & L for matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 15mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per directed.

Dismantling of stone slab and tiles of any description or thickness in floors, etc. laid dry & laid dry in pointed. Complete all as specified & as directed.

Providing and fixing 20 mm thick gang saw cut, mirror polished, premoulded and prepolished,Granite of any colour and shade machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete all as specified & as directed

M&L for Machine cut kota stone slab flooring 20-25 mm (slab shall not be less than 550mmX550mm) thick over cement screed 20 mm thick in cement mortar 1:6, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L for Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over cement screed 15 mm thick in cement mortar 1:4, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Note : Riser of steps shall be in one piece only . Complete all as specified & as directed.

Cutting, polishing existing Kota/ marble floor flooring,& verticle surfaces (three cuttings and mirror polishing) including Manson polishing, levelling certain places to Kota/ marble floor ,necessary repair work & all necessary arrangments complete as directed.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. Complete all as specified & as directed.

S&F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks, or galvanised wire staples. Complete all as specified & as directed.

All as per item No 55 above but supply and fix in repairs.

Hacking out old broken glass any thickness, size, quality or description from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads including S&F 3 mm thick plain sheet glass ordinary quality in square not exceeding 0.5 sqm in each pane complete all as specified & directed

M&L for Sheet glass ordinary quality 3 mm thick and glazing with oil putty in square n. exc 0.50 sqm in each pane. Complete all as specified & as directed.

Dismantling wall and ceiling boards ( fibre, pulp, insulation ,etc. ) or insulation boards/slabs/blankets, any thickness, including cover fillets. Complete all as specified & as directed.

Supply and fixing anodized snap grid frame work of size 605mm x 605 mm for false ceiling including necessary notching. The snap grid shall consist of anodized aluminium main & cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg/RM and 23.5 x 26.4 x 1.40 mm weighing 0.191 Kg/RM respectively. The main and cross tee shall be jointed at junction crossing with anodized aluminum angle bracket of size 15mm x 15mm x 1.5 mm weighing 0.12 Kg/RM fixed with suitable MS bolts, nuts and washer. The snap grid (main/cross tee section) shall be supported at ends all along the wall with anodized aluminum angle of size 40 x 25 x 2 mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and providing 12 mm thick mineral fibre board of make Armstrong in fixed in grid support with 2.50 mm dia plain mild steel wire galvanised class 3 fixed in detached works etc to support snap grid,as per specification complete all as specified and as directed.

Dismantling and taking up or down the existing unserviceable GI pipe and supply and fix for new galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors of following sizes :-

15 mm bore

20 mm bore

40 mm bore

Taking up or down old serviceable GI pipe Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, trenches etc ) including cleaning of following sizes.

15 mm bore

20 mm bore

40 mm bore

S&F in repair bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore, fixed in repairs. Complete all as specified & as directed

S&F stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed of following size in repairs. Complete all as specified & as directed.

15 mm bore

20 mm bore

S&F in repair brass ball valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed of 20mm bore, fixed in repairs. Complete all as specified & as directed.

S & F in repair of vitreous china squatting pan, 'Orissa' pattern, size 580x440 mm white, with integral foot rests, 'P' or 'S' trap, including connection to trap, and to flushing pipe, anti-syphonage pipe etc. complete including making good to floor with PCC, Lime concrete bedding. Complete all as specified & as directed.

S&F in repair of pillar tap, cast copper alloy with capstan heads,chromium plated, fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore including Complete all as specified & as directed.

S&F of pillar tap, cast copper alloy with capstan heads,chromium plated,fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore Complete all as specified & as directed.

Dismantling of old existing unserviceable WHB glazed and S&F new vitreous china wash hand basin, white, of size 550x400mm flat back excluding taps, waste, chain and plug but including brackets, cutting for and pinning in ends of brackets or erecting stand complete . Complete all as specified & as directed.

S&F waste fitting brass chromium plated for 32mm bore with long screwed shanks and fly nuts including 32mm PVC waste pipe for WHB. Complete all as specified & as directed.

S&F Sink with drainage board made of stainless steel 1 mm thick Kitchen or Laboratory with plugs, washers and wastes; including beding in cement mortar on to dwarf walls or including fixing cantilever brackets and connecting union to waste pipe overall size 915mm x 460mm bowl size 410mm x 330 mmx160mm. Complete all as specified & as directed.

S&F in repair of brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union including taking down of old shower rose of any size, any type Complete all as specified & as directed.

S&F in repair of PVC low level flushing cistern 10 ltrs capacity with inlet ball valve float & handle, syphonic action type including brackets & flush pipe of polythelene of low or high density or PVC 32mm dia for LLFC fixed in repairs. Complete all as specified & as directed.

S&F in repair of aluminium anodised tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges. Complete all as specified & as directed.

M&Lin repair of cast iron nahani trap of 75mm bore, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4). Complete all as specified & as directed

Demolition & breaking up drain pipes AC, (Salt glazed ware, AC or Reinforced concrete) set in CM Internal dia of pipe upto 100 mm. Complete all as specified & as directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, ISI marked of 75mm bore.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, ISI marked of 110mm bore. Complete all as specified & as directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, ISI marked of 75mm bore. Complete all as specified & as directed.

S&F sinks made of stainless steel 1mm thick kitchen or labortory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 1215mm x 460mm, bowl size 410mm x 330mm x 190mm including waste pipe of polythelene of low or high density or pvc 32 mm dia &waste coupling brass chromium plated for 32 mm bore with long screwed shank and fly nuts including making holes in any type of wall for brackets and fixed in cm 1:3 or pcc 1:2:4 type B0 complete fixed in repair. Complete all as specified & as directed.

Dismantling of old U/S grating of any description or size and S&F new CP cockroch trap grating 100 mm dia of weight not less than 40 gm for floor trap/Nahani trap. Complete all as specified & as directed.

Preparation of new or previously untreated steel surface of any description not oterwise described over 10 cm width or girth and appying two coat of synthetic enamel paint over a coat of red oxed prier all as specified and directed.

M & L prepration of new wood or wood based surface of any description over 10 cm widtgh or girth and applying two coats of synthetic enamel paint over a coat of pink primer. all as specified and directed.

Dismantling 1000 ltr water tank and M&L triple layered 1000 ltr ISI marked rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position & including 20mm brass ball valve also providing Square/ Rectangular ,raised platform of hight 20 cm below the tank and base dia min 100 MM projected by the external dia all around of tank for pvc cylendrical tank of capicity 1000 liters using pcc 1:3:6 type C1 using 20 mm graded stone aggregate with smooth finish including necessary form work etc. all as specified and directed.

Dismantling 500 ltr water tank and M&L triple layered 500 ltr ISI marked three layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position & including 20mm brass ball valve also providing Square/ Rectangular, raised platform of hight 20 cm below the tank and base dia min 100 MM projected by the external dia all around of tank for pvc cylendrical tank of capicity 500 liters using pcc 1:3:6 type C1 using 20 mm graded stone aggregate with smooth finish including necessary form work etc.all as specified in ssr part-I. Complete all as specified & as directed.

S&F for in repair Brass Chromium plated Angular stop cock with wall flange complete all specified. (Make;- ESSCO cat part no APR 101053 or equivalent in Jaquar ,parrware )

M&L for PVC connection 15 mm size with PTMT nuts of length 600 mm. Complete all as specified & as directed.

PD GUPTA AND COMPANY

R.S BUILDERS

GANGA CONSTRUCTION

krishna Associate