85958 SPL REPAIRS / RENOVATION TO EXISTING DRAINAGE SYSTEM AND REPAIR / RENOVATION TO EXISTING BOUNDARY WALL OF DAD RESIDENTIAL COMPLEX OF A AND B WING WANOWARI PUNE UNDER GE (SOUTH) PUNE

Amount

Excavating in trenches, not exc. 1.5 m wide and not exc. 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 sqm on plan and not exc. 1.5 m in depth and getting out in soft disintegrated rock all as specified and directed.

Excavating in trenches, not exc. 1.5 m wide and not exc. 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 sqm on plan and not exc. 1.5 m in depth and getting out in hard dense soil complete all as specified and directed.

M&L for excavating over areas, not exc. 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.

M&L for excavating over areas, exc 1.5 m but not exc 3.0 m deep and getting out in soft disintegrated rock complete all as specified and directed.

M&L for excavating over areas, exc 1.5 m but not exec 3.0 m deep and getting out in hard rock complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C-1, (using 20mm graded stone aggregate) with solid blocks, exc. 10 cm in width and setting in CM 1:6 etc, as in drain wall complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C-2, using 40mm graded stone aggregate as in bed blocks, mass concrete etc complete all as specified and directed.

M&L for plain cement concrete 1:3:6, using 12.5 mm graded stone aggregate as in bed blocks etc complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1, using 20mm graded stone aggregate as in drain channel coping etc complete all as specified and directed.

M&L for RCC 1:2:4 (Nominal Mix) type B-1, using 20mm graded stone aggregate as in drain cover slab supported on drain wall etc complete all as specified and directed.

M&L for RCC (Design Mix) M-25 (using 20mm graded aggregate stone) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC (Design Mix) M-25 (using 20mm graded aggregate stone) as in columns, pillar, post and struts etc complete all as specified and directed.

M&L for RCC (Design Mix) M-25 (using 20mm graded aggregate stone) as Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed.

M & L for brickwork with fly ash bricks, straight or curved on planot exc. 6m mean radius, built in CM (1:6) complete all as specified & directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

S&F Factory made precast SFRC cover slab of 100mm thickness in drain cover of area exc. 0.60 sqm & not exc. 0.75 sqm including groove and hook arrangement for lifting and placin at site and also side of cover shall be covered MS sheet with collars etc complete all as specified and directed. (Ref. Drg No. CEPZ/92/TD/11M, Sheet 02/02)

M&L for Mild Steel TMT bars 10 mm Dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for Mild Steel TMT bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290 Gde-E-165 complete all as specified and directed.

M&L for 15 mm thick on fair faces of brick work, block masonry or concrete wall surfaces in CM 1:4 to be finished even and smooth (without using extra lime or cement) complete all as specifed and as directed.

M&L for 15 mm thick on fair faces of brick work, block masonry or concrete wall surfaces in CM 1:4 to be finished even and smooth with integral waterproofing compound as per manufacturer's instruction complete all as specifed and as directed. (Note: WPC shall be measured and paid seperately)

Supply only liquid type water proofing compound complete all as specified and directed.

S&F stainless steel concentrina coil for fencing of any dia continuous punched blade edged barbs weather and fire resistance complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches/floor complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in soil complete all as specified and as directed.

M&L for removing excavated material exc. 250 m but not exc. 500 m and depositing complete all as specified and directed.

M&L for Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed.

M&L for demolition/dismantling Stone slabs and concrete tiles of any description or thickness in floors, aprons etc laid bedded and jointed in cement motar complete all as specified and directed.

M&L for demolition/dismantling brick work or stone/masonary work but built in cement mortar or cement lime mortar complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D-2, (using 40mm graded stone aggregate) as in sub base to floor/pavings etc complete all as specified and directed.

M&L for PCC 1:4:8 type D-2, (using 40mm graded stone aggregate) as in foundation filling etc complete all as specified and directed.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of crushed sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

Fixing only machine paver blocks retrieved from ser. Item No. 31.00 above laid over & including 50mm thick stone dust/grit complete all as specified and directed.

M&L for preparation of new steel surfaces of any description not exc. 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as specified and directed.

M&L for mild steel framed work posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290, Gde E-165 complete all as specified and directed.

M&L for galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) all as specified and as directed.

M&L for prepration of newly plastered wall surface and applying two coat of cement based paint complete all as specified and as directed.

Supply only for Mild steel in flat, round or square bars, in available lengths of Fe 410-W (Gde-E-250) quality-A complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specifed and directed.

Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and directed.

M&L for Cutting holes into or through cement concrete slabs, chajjas, etc. reinforced or reinforcement or otherwise complete all as specified and directed.

M/S Sharvi Construction (BID ID -3478170)

Vijay Construction and Company (BID ID -3477530)

M/s.BAJRANG CONSTRUCTION (BID ID -3477876)

Mehta Construction Co. (BID ID -3477904)

Sunshine Ventures (BID ID -3477756)

Crown Chemicals (BID ID -3477869)

D S MADANE ENGINEERS AND CONTRACTORS (BID ID -3476528)