SPL REPAIR OF TWO OFFICES IN BLDG NO LSM-48 OF 101 AREA UNDER GE SHILLONG

Taking down chowkat or frame exc 1.5 Sqm but n.exc 4 Sqm each (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames n. exc 1.50 Sqm each with shutters (without taking off shutter from the frames) complete all as specified and directed.

Demolition of Brickwork/solid concrete block work built in Cement mortar complete all as specified and directed.

Dismantling unframed wooden work in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any guage, thickness incl Nainital, similar pattern as in roof coverings. complete all as specified and directed.

Dismantling floor, hearth , wall tiling including cement mortor bedding (but not backing) removing serviceable tiles to store and rubbish off the premises

Dismantling of stone slabs and tiles of any description or thickness in floors aprons laid in any mortar

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed please.

Dismantling boarding any description fixed in any position with nails complete all as specified and directed

Dismantling of timber scantling 40 sqcm over in section in any position (unframed work).

Excavation in post holes each n.exc. 0.5 cum in soft/loose soil getting out returning, filling in and ramming earth or broken rubble mixed with earth around in layer n.exc. 25 cm, watering and removing surplus soil to a distance n.exc. 50 mtr and making good surface complete all as specified and directed.

M&L Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in sub base,foundation filling and mass concrete etc.complete all as specified and as directed.

S&F steel work as in tubular , rafters, purlins, posts and similar work (round/square/rectangular shape of pipes as approved by Engr-in-charge ) trusses of semi circle/ curved shape up to height 6 mtr including post special shaped washers, gusset plates etc complete using ERW or induction butt welded tubes conformining to IS 1161-1998 garde St-240 complete all as specified by Engr-in-Charge.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre using Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified to plaster of paris ceiling (Gypsum anhydrous board) complete all as specified and as directed .

M&L for Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous board) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately)

S&F for 10mm thick coloured PVC panels with EPS stuck to colour PVC sheet suitably placed in false ceiling/wall panelling, grid made of Aluminium/G.I./M.S. or wooden fillets as per specification and drawing all as specified and directed.

M&L for 2nd class hard wood plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads , sectional area exc. 13 and n.exc. 25 sqcm

S&F 2nd class SW boarding 20mm thick fixed with nails in eaves board plained one side with butt joint complete all as directed.

M&L 2nd class hard wood in scantling clean sawn timber fixed all as specified.

M&L 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid ,rounded or chamfered ,put together with glue pinned at joints , supplied and fixed.

S&F 35 mm thk Flush door shutters solid core construction with block board core and plywood face pannels , commercial type on both sides complete all as specified and directed.

S&F 18/19 mm thick block boards fixed with screws to timber frame complete all as specified and as directed.

M&L 12 mm thick Plywood (07 Nos of ply) , grade BWP, type BB, fixed with screws to timber frame work complete all as specified and as directed.

S&F 1.5 mm thick decorative laminates type 1 of surface finish color and pattern as approved fixed with approved adhesive as per manufactures instruction complete all as specified

S&F telescopic channel / ball bearing drawer channel of size 500 mm long complete all as specified and as directed.

S&F W- hinges 75 mm medium weight, stainless steel, and fixed complete all as specified and directed.

S&F W- hinges 125mm, medium weight, stainless steel, and fixed complete all as specified and directed.

S&F 200mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts complete all as specified and directed.

S&F 100mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts complete all as specified and directed.

S&F Extruded brass handles, fabricated type polished of size 250 mm complete all as specified and directed.

S&F Extruded brass handles, fabricated type polished of size 150 mm complete all as specified and directed.

S&F Magnet catches for cupboard shutter, brass body and striking plate including letting in all as specified and as directed

S&F 30mm width of flaps (When open in mm) continuous (piano) hinges, mild steel , bright finish or electro galvanised complete.

S&F Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) of size 300mm long and fixing bolt with rolled or drawn brass bolts and fixed complete.

S&F 6 lever Brass Matte finish door handle of 200mm long with 1xmortice lock, 1xstriker plate, 1xsquare shank including keys and all other necessary accessories fixed , colour and design as approved by GE complete.

M&L for 8 mm thick sheet glass quality and glazing fixed to aluminium frame n.exc 0.50 sqm complete all as specified and as directed.

M&L for 8 mm thick sheet glass quality and glazing fixed to aluminium frame exc 0.50 sqm complete all as specified and as directed.

M&L for 6 mm thick plain sheet or black tinted glass quality and glazing fixed to any metal / non metal frame of any size complete all as specified and as directed.

M&L for 4.80 mm thick frosted sheet glass quality and glazing fixed to aluminium frame n. exc 0.50 sqm complete all as specified and as directed.

S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed.

M/L precast cement concrete block massonry with solid blocks exc 10 cm in width and settings in CM 1:6 type C1 1:3:6 (20mm graded aggregate) complete all as specified.

M/L precast cement concrete block massonry with solid blocks nexc 10 cm in width and settings in CM 1:4 type C1 1:3:6 (20mm graded aggregate) complete all as specified.

S&F pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tenssile strength of 550 Mpa as in roof covering / cladding including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, complete all as specified and directed by Engr-in-Charge.

S&F pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tenssile strength of 550 Mpa as in roof covering including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and directed by Engr-in-Charge.

M&L for 10-12mm thick premium quality wooden laminate flooring , waterproof ,AC4 grade with superior wear resistance, featuring MDF and HDF base materials , abrasion Class Standard, European Flooring Standards, Waterproof Certification of planks size 4' x 8" x 8mm including 2mm thick layer of foam for cushioing colour and design as approved by GE complete.

M&L for 20 mm thick cement mortar screed bed or bedding layer for laying floor finishes in CM 1:6 complete all as specified

M&L for 40 mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) used over sub base to recd floor tiles complete all as specified and directed

M&L for Virified Ceramic tiles 9-10 mm thick light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and laid over and including15 mm thick cement screed bed in CM 1:6 complete all as specified

All as per Item No 53 above here–in–before but on vertical surfaces such as skirtings and risers to steps etc. over 10mm thick rendering in CM 1:4 as in backing coat complete all as directed.

M&L for 18/20mm thk granite slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and incl pointing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite over and including 20 mm thick cement screed bed in CM 1:4 complete all as specified.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking plateform, and other similar situation.

Taking down plastering on lathing (other than wire-netting, without removing lathing, in cement mortar (one side only measured in cases where both sides are plastered).

M&L for rendering 10mm (cement plaster 1:6) thick on block masonry surfaces or surface other than fair face of brick-work or on one side of lathing complete.

M&L for rendering 15mm (cement plaster 1:4) thick on block masonry surfaces or surface on the other side of lathing complete.

S&F 35mm thick premium teakwood ornamental designer door shutters of solid core construction design and colour approved by GE complete.

M&L for 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints ,laid in trenches or in floors complete

S&F PVC (SWR) bends 110mm dia complete all as specified and as directed

Supply and Fix half round PVC rain gutter of dia 180 mm including clamps, bolts and nuts complete all as specified and as directed,

M&L 75mm thick cement concrete using (40mm graded aggregate) type D-2 (1:2:4) as in sub base.

M&L for 75 mm thick cement concrete 1:2:4, type B-2 (using 40mm graded agg) as in plinth protection finished even and smooth without using extra cement.(incl necessary joint filling with mixture of paving bitumen & sand in 1:3).

S&F MS framed work such as grills, gratings, etc with ends of bars, shouldered and/ or riveted or forged into spikes framed guard bars, barred iron doors, ladders, framed balusters, walk way, railing and framed work of water tanks and similar work confirming to Fe 290 Gde E-165 complete all as specified and as directed.

S&F for designer 25mm wide wooden beading for showcase or any wooden structure as approved by GE complete.

S&F stainless steel slider channel for wooden cabinet or shutter with automatic soft close hinges and bracket including all necessary accessories fixed complete.

S&F false ceiling gypsum cornice moulding of 100mm wide facades and soffit as design approved by GE.

M&L for preparation of old painted concrete/plastered surfaces of any description , over 10 cm in width or girth, not otherwise described and applying 1mm thick of white wall care putty or cement paste to achieve smooth surfaces and applying two coat of plastic emulsion paint of approved shade/tint over a priming coat paints plaster all as specified.

M&L for preparation of newly concrete/plastered surfaces/gypsum board of any description , over 10 cm in width or girth, not otherwise described and applying 1mm thick of white wall care putty or cement paste to achieve smooth surfaces and applying two coat of plastic emulsion paint of approved shade/tint over a priming coat paints plaster all as specified.

M&L for preparation of new steel surfaces of any description , over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat red oxide primer all as specified.

M&L for preparation of new or previously untreated surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer all as specified and as directed.

M&L for preparation of old surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer all as specified and as directed.

M&L for preparation of plastered or unplastered old decorated surfaces of walls by washing rubbing down and stopping of any external painted surfaces and priming with alkali resistant primer paint applying two coats of weather coat exterior paint with roller incl filling of holes and cracks with suitable material like cement or plaster of paris etc complete all as specified and as directed.

M&L for preparation of new plastered/concrete surfaces of walls and priming with alkali resistant primer paint applying two coats of weather coat exterior paint with roller etc complete all as specified and as directed.

Taking down carefully copper/aluminum point wiring light/fan/sockets out let/power point complete (fittings such as switches, sockets, ceiling rose, pendent holders, light fittings etc. are to be measured separately) and/or drawing out from existing conduit/batten and making good disturbed surface of walls/floors/ceiling, complete all as specified.

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box/metal flush box with suitable modular or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light/fan point controlled by one switch.

Description all as per Srl item No 78 here in before but for socket outlet point 5 Amp on same board.

All as per item No 78 above but One call Bell point controlled by one bell Push on independent Board

Description all as per Srl item No. 78 here in before but for socket outlet point 5 Amp on Independent board.

Description all as per serial item No 78 above but with 4 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point) complete all as specified.

Supply and fixing modular switch 1 way 6 A with cover plate and frame 230/250 volt , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed.

Supply and fixing modular bell push 1 way 6 A module 230/250 volt , AC supply, ISI Marked, with cover plate complete all as specified and directed.

Supply and fixing call bell ding dong, AC, 230 V, Single pole ISI marked all as specified and directed.

Supply and fixing modular switch 1 way 16 A with cover plate and frame230/250 volt , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed.

Supply and fixing modular sockets with cover plate and frame 6A 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked, with cover plate complete all as specified and directed.

Supply and fixing modular sockets 6A/16A 2/3 pin combined 2 module with cover plate and frame 230/250 Volts, 50 Hz , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed.

Supply and fixing round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing round shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix Flexible LED strips complete all as specified and direcetd.

S & F LED light fitting /1X20W Focus down light white/warm white connecting up with three core flexible copper conductor cable of suitable size Make Jaquar cat part No. LFCL01R020XC..

Supply and fix in repair MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 12 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection, including taking down complete all as specified and directed.

Supply and fix MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed

Supply and fix in repairs MCB, single pole 240 volts 6 to 32 Amps capacity fixed in DB's.complete all as specified and directed

M & L Sub main wiring with two run single core 6 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia concealed on wall/ceiling in PVC conduit, medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall along with one run of 6 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion including taking down old wiring etc complete all as directed. Note: (i) Two runs of 4 sqmm and one run of 6 sqmm cable and one run of PVC conduit shall be measured as one RM. (ii) Cutting of chases in the wall of appropriate size shall be carried out with electric cutter machine . (iii) Necessary plastering in the disturbed surface of wall and distempering /white washing to match the existing colour shall be included in the unit rate quoted.