PROVISION OF CENTRAL PARKING STAND FOR 100 FOUR WHEELERS AND 50 TWO WHEELERS AT ARC MAHIPALPUR (RESTRICTED AREA) UNDER GE (SOUTH WEST) NEW DELHI-03

Amount

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/ dense soil complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone agg) in foundation filling, sub base and mass concrete filling etc. complete all as specified and as directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces complete all as specified and directed.

M&L for TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT steel bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for RCC (Nominal Mix) type B1 1:2:4 Using 20mm graded crushed stone aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

S & F plain/ chequered MS plate incl cutting / welding & drilling confirming to Fe-290 (Gde -165) complete all as specified and directed.

S&F Factory moulded steel tubular trusses, purlins, rafter vertical post and similar works including special shaped washer etc. complete using ERW or induction butt weled tubes including cleats, plates, hold fast and including conforming to IS 1161-1998 Gde st-240 complete all as specified and directed.

S&F mild steel hollow section purlins and similar works including special shaped washer etc. complete using ERW or induction butt weled tubes including cleats, plates, hold fast and including conforming to IS 1161-1998 Gde st-240 complete all as specified and directed.

S&F for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10 cm and n exc 15 cm long (Dia of neck 11 to 15 mm) complete all as specified and directed.

S&F factory moulded pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L for Ready mix Cold Bitumen for making surfaces good of distrubed portion of pavement complete all as specified and as directed.

M&L for painting steel and iron surfaces of steel surfaces of any description, over 10cm in width or girth, not otherwise described, applying two coats of synthetic enamel paint over coat of red oxide primer including preparation of new surface complete all as specified and directed.

VINAY ENTERPRISES (BID ID -3261763)

M/S ANIL KUMAR (BID ID -3258373)

OM ENTERPRISES (BID ID -3261768)

HANUMAN BUILDERS (BID ID -3261740)

Vishal Traders (BID ID -3259622)

JPMS BUILDTECH (BID ID -3262260)