PROVN OF CERTAIN SANCTION WORK, REVENUE WORKS AND MINOR WORKS AT AF STN DINJAN UNDER GE (AF) MOHANBARI

Amount

Surface excavation n.exc 30cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep and getting out in soft/loose soil complete all as specified and directed.

Removal of surplus soil not exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well raming in layers n.exc 25cm thick complete all as specified and directed.

M & L for provision of PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete including demolition of existing concrete and removing the rubbish off complete all as specified and directed.

Form work to sides of concrete foundation, footings, base of columns, raft and raft beems, sides and soffits if any of foundation and plinth beems and similar work, verticle or to batter of rough finished surfaces of concrete flat complete all as specified and directed.

Form work to sides of pillars, posts, struts, piers, columns and stanchions of rough finished surfaces of concrete square rectangular or polygonal complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc. also splays between floors and beams etc complete all as specified and directed.

M & L for reinforced cement concrete (RCC) M25 Design Mix as in footing, plinth beams and columns below GL etc complete all as specified and directed.

M & L for reinforced cement concrete ( RCC) M25 Design Mix as in column above GL etc complete all as specified and directed.

M & L for reinforced cement concrete( RCC) M25 Design Mix as in slab supported on wall, beam complete all as specified and directed.

M & L high strength deformed TMT steel bars 10mm dia and over as in reinforcement cut to length, bent to shape required including cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L High strength deformed TMT steel bars 8mm dia and over as in stirrups cut to length, bent to shape required including cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for brick work with sub class 'B' bricks built in cement mortar 1:6 straight or curved on plan & exc 6 m mean radius with old size bricks complete all as specified and directed.

M & L for rendering 15mm thick in cement mortar 1:4 on brick/concrete surface as in external wall surface etc., finished fair and even without using extra cement complete all as specified and directed.

M &L for applying Two or more coats of 100% Premium acrylic emulsion paint (Camouflaluge pattern) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

M&L providing precast cement concrete jallies PCC 1:2:4 type B-0 (using 12.50mm graded stone aggregate) 35mm thick (measured solid) including all moulding and set in cement mortar 1:4 complete all as specified and directed.

M&L for broken stone as hard core of gauge n.exc 63mm, deposited, spread and leveled in layers n,exc 150mm thick, watered and rammed to true surface complete all as specified and directed.

Material and labour for plain cement concrete type C-1 (1:3:6), using 40 mm graded crushed stone aggregate, 75 mm thick, as in plinth protection, pathway finished even and fair without using extra cement complete all as specified and directed.

M&L PVC (SWR) pipes 110mm dia single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Preparing of existing concrete surface and grinding with Grid -36N Paper complete all as specified and directed.

SYNTHETIC 8 LAYER OUTDOOR SPORTS SYNTHETIC SURFACE:- The system is 8 layers and consists of :- (a) Acrylic Resurfacure for filling and smoothing subfloor (02- layers) (b) Triple Layer of Acrylic Rubber cushion (03-Layers) (c) Anti Skid Base Coat (Base color coat) (01-Layer) (d) Hybrid waterborne HPU-500 Top coat to protect flooring against UV Rays with overall line markings (02-Layers) Make-Pace Court or equivalent as approved by GE

Excavating in post holes (or similar holes) in soft/loose soil each n.exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

M & L for damp proof course to horizontal or vertical surfaces including necessary formwork, 40mm thick, in cement concrete 1:2:4 type B0 complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

Material and labour for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement and sand mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.

Material and labour fo preparation of new plastered or unplastered surafces of walls and applying three coats of white wash including washing floors, cleaning glass, joinery, electrical fittings, wiring etc, of drops and splashes complete all as specified and directed.

Material and labour for preparation of newly plastered surface of wall and applying two coat of cement base paint over a coat of cement based primer of any tint/shade including washing floors, etc. , of drops and splashes complete all as specified.

Supply and Fix mild rolled Steel section as in main and cross beams ,hip and jack rafters, purlins where connected to common rafter and running eails and guide for sliding doors fixed with angle cleats or other connecting plates conforming to IS : 1161- 1998 grade Fe 410 W ( Grade E 250) Quality B complete all as specified and directed.

S& F of pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, including ridge cover fixed with self tapping screws etc complete all as specified and directed.

S&F MS screw bolts (Machine Made) with hexagonal or square heads at one end and screwed the other each screwed end to be fixed with one washer and one hexagonal nut, 5 to 10 mm dia of length exceeding 50 mm but not exceeding 100 mm long complete all as specified and directed.

S&F MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for 75mm thick PCC type D2 1:4:8 (40 mm graded stone aggr) as in sub base of floor finished even and rough to receive floor finishes complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B1 using 20mm graded stone aggr as 40 mm thick hardstanding, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L PCC 1:2:4 type B-0 using 12.50mm graded stone aggregate as in coping, bed plate etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete including removing dismantled material from work site complete all as specified and directed.

Dismantling wooden boarding, any description, fixed in any position complete all as specified and directed.

(a) Supply & installation of Access floor shall be of our Brand - NEX LEVEL_Access Floor with high performance fs 800 grade tiles/panels. having a point load of 2.2 KN / Over 25mm sq. and UDL of 12 KN/m2 . Panels/Tiles are manufactured from prime quality steel with light weight cementious core in the size 600 x 600 x 33.5mm thickness. (b) The panels shall be finished with high abrasion, anti- static high pressure laminate in size 600 x 600 x 1.2mm, conductive PVC edge bidding on the sides with a cut at 45 degree along every edge of the panel to avoid edge chipping, breakages, pealing, lateral deflections and scratching between 2 panels. (c) The bottom of the panel shall be embossed in 64 hemispherical shaped domes to give strength and flexural rigidity. The entire panel shall be finished with electro deposition of cathodic epoxy coat on exposed surface for lifetime protection. (d) The panels will be placed on pedestals of height 450mm and stringers made from galvanized all steel & zinc plated construction. Pedestal & stringer assembly provided will have easy adjustments of leveling and accurately align panels to ensure lateral restrain.Pedestal heads are fitted with PVC caps which are designed to avoid rattle or squeaks.

Material and labour for 125 mm x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strikes plate, etc complete all as specified and directed.

M&L for preparation of previously untreated surfaces steel of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material and labour for preparation of new surfaces of walls and applying two coats of acrylic based distemper emulsion over a coat of cement based primer, white or tinted including washing floors, cleaning glass, joinery,electrical fittings, wiring etc of drops and splashes complete all as specified and directed.

Supply and fix for 30 mm thick Flush door shutter, solid core construction with block board core and plywood face panels commercial type on both side complete all as specified and directed.

M & L Preparation of new wood surfaces of any description over 10cm width or girth and priming with pink primer and painting with synthetic enamel painting two coats complete all as specified and directed.

S&F for 300 mm long Aluminium alloy anodised sliding door bolts with hasp and staple(bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium and fixed complete all as specified and directed.

S&F for 100mm size, mild steel butt hinge medium weight cold rolled & fixed complete all as specified and directed.

S&F for 150mm length aluminum, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 150mm size aluminum handles, cast type anodised complete all as specified and directed.

Material and labour for cement concrete 1:2:4 type B-1 as in Beams, cantilevers, bressummers,lintels over 1.5m span complete all as specified and directed.

Material and labour for Mild steel deformed or twisted bars ( TMT) 8 mm dia and over, cut to length, bent to shape required, hooking ends and binding with including mild steel wire (annealed) not less than 0.90 mm dia. or higher complete all as specified and directed.

M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs,etc. also splays between floors and beams, etc complete all as specified and directed.

Material and labour for PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in hold fast block, filling in pressed steel chowkats including necessary form work etc complete all as specified and directed.

S & F 1.6mm thick GI hot dip galvanised / powder coated perforated type cable trays of size 200mm width, 50mm depth and including cover plate of 200mm size and 1.2mm thickness and necessary bend, Tee,and other necessary accessories fixed with and including necessary MS clamps, nuts, bolts and mounted on iron structure/legs of min height 10cm from GL with frame complete for laying of cable fixed to walls / ceiling /floor complete complete all as specified and directed.

M&L for installation and testing of maintenance free earthing complete with earth electrode as per IS 3043 or latest tested for 254 micron copper bonded low carbon steel core of 3 meter long, 50 mm dia with 25X3 mm inner copper strip buried directly in ground and tapered at the bottom (175- 200 mm dia digging or auguring of earth to the required depth as approved by tpmpgraphic survey report) and filled up in bottom with slurry 10 Kg plain bentonite for moisture and then with earthing chemical as per design as per recommendation of tomogharhic survey report as per IS/ IEC-62561-7 of Balanced Ph and less than 0.2 Ohm Resistivity carbon based earth enhancing compound in slurry form and quantity as per design. An arrangement for connection of copper strip (25x3mm) to rod connected by means of Universal Copper Ground Rod Clamp of size 135x35x3mm to the electrode, copper earth strip 20x3 mm connected by means of clamp, provision of HDPE pit cover with minimum 5KN load capacity chamber with cover including necessary excavation in any type of soil, returning filling in, removal of surplus soil complete all as specified and directed. Note:- (i) Earthing system shall be designed so as to achieve test result less than 1 Ohm depending upon the soil conditions for the minimum 2 Years under warranty. (ii) Copper strip to be extended upto the equipment and power room. It should be routed on the side wall of the underground duct fixed with ceramic/ porcelain/ PVC spacers and hot sleeves. (iii) Ready made HDPE pit chamber with cover having minimum load capacity 5 KN with connected items. (iv) Copper strip should be 20x3 mm and length upto 7.5 Mtr is deemed to be included in the item qouted rates. (v) The number of earthing electrode in each earthing pit shall be as per design carried out in tomographic survey carried out vide Job No -21FBSU/CAP(OTM)/03/2022-23 and 21FBSU/CAP(OTM)/02/2023-24 . Any extra cost for universal number of pits as per design shall be deemed to be included in item quoted rate.

M&L for 20X3 mm copper strip for earthing connection to building, complete all as specified and directed.

Supply and fixing GI protection pipe of 40 mm dia light grade for cable protection including all fittings laid in trenches or fixed on pole/ walls/ laid in floor with mild steel clamps, bolts, nuts and washers complete all as specified and directed.

M & L for point wiring with 1.5 sqmm cable PVC unsheathed and insulated copper multistranded conductor (FRLS) 1100 Volts grade cable (red colour cable to be used for Phase connection and black colour cable to be used for neutral connection) including PVC conduit with all accessories including 1.5 sqmm copper multistrand conductor FRLS 1100 Volts grade unsheathed PVC insulated (green colour) continuity earth wire connected to common earth dolly and sunk cast pressed steel terminal box made out of MS sheet 1.2 mm thick for mounting of fittings like switch, socket and fan regulator with 3 mm thick hylum laminated sheet cover complete all as specified and as directed.

Light/Fan/Exhaust fan

5 Amp switch socket on Independent Board (for wall mounting fans).

S&F of switch socket combination 2 in 1, 5/6 Amps flush type230/240 V complete all as specified and directed.

S&F of ceiling rose 3 phase/PVC/polycarbonate,isolated body, surface type with ISI marked complete all as specified and directed.

S&F of switch piano flush type 5/6 amps, 240 volt single pole one way complete all as specified and directed.

S&F of Step type electronic fan regulator flush type 230 volt 5 speed control and connecting up and fix position complete all as specified and directed.

Supply and fix of exhaust fan, steel body AC single Phase. 230V of size 300m sweep 1400RPM, and min air delivery 1850m3/h with, blades, and frame and louvers complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Cutting the existing stone/brick masonry wall for fixing the Exhaust fan of any size/sweep including plastering with cement plaster and making good surfaces complete all as specified and directed.

Supply and fix wall mounted fan, steel body AC single Phase. 230V of size 450m sweep with, steel blades, and frame with provision of ossilation of 60 degree with speed and ossilation control with min 1400 RPM and air delivery of 110 cum/min complete all as specified and directed.

G S Enterprises & Co (BID ID -3138456)