Construction and Developmen...

NS Item -Sea-Saw Main Structure Material:Galvanised Steel (GI)ERW Pipes ISI Marked IS1239 Minimum90 mm outer diameter (OD),2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating(min.60-80 microns),Bending with fully automatic PipeBending Machine,Welding With Laser Welding Heigh Power Machine. Handle andLeg rest Material:Galvanised Steel (GI)ERW Pipes ISI Marked IS1239Minimum 25 mm outer diameter (OD),2.0- 3.0 mm thickness Surface Finish Zinc primer plus outdoorgrade polyester powder coating(min.60-80 microns),Bending with fullyautomatic Pipe Bending Machine,Welding With Laser Welding Heigh Power Machine.Seat:designed for outdoor playgrounds.Crafted from durable 3 layer HDPE sheets 20mm thik and precision router-cut for Spring:Heavy-duty coil spring,High-carbon steel oralloy spring steel,18 mm-20 mm wire thickness,Coil height:Approx.300 mm. Clamps and Connectors Material:Die-cast aluminium or aluminium alloy Finish:Naturalanodized or powder coated Properties:Anti-rust,tamper-resistant,non-toxic.Fasteners Material:Galvanized Iron(GI),zinc-coated Type:Tamper-proof bolts and nuts Rust Resistance:Min.500 hours salt spray test protection:Plastic safety caps on exposed bolts. Surface Coating Primer:Shot Blasting surface treatment process using high elocity, steelabrasive Epoxy zinc-rich primer (40 microns)Top Coat:Outdoor polyester powder (60-80microns)Adhesion:5B rating(ASTM D3359)Color Options:Custom RAL shades,UV-stabilized Safety Compliance Standards:EN 1176 (Europe)ASTM F1487 (USA)Fall Height: Compliant up to 2.5 meters Surfacing(optional):Prevention:No head,neck,or finger entrapment zones Edge Protection:Rounded corners,no sharp edges. Installation:RCC blocks or anchor bolts with M20 grouting Installation:Certified team with adherence to manufacturer`s layout Tools and Hardware:Supplied with the product Site Preparation:Level ground,drainage recommended

NS Item -CHEERFUL CHURN Main Structure Material:Galvanise Steel (GI)ERW Pipes ISI Marked IS1239 Minimum 90mm outer diameter (OD),2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoorgradepolyester powder coating(min.60-80 microns),Bending with fully automatic Pipe BendingMachine,Welding With Laser Welding Heigh Power Machine.,Bending with fully automaticPipe Bending Machine,Welding With Laser Welding Heigh Power Machine. Support Structure Material:Galvanise Steel (GI)ERW Pipes ISI Marked IS1239 Minimum 40mm outer diameter (OD),2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoorgradepolyester powder coating(min.60-80 microns),Bending with fully automatic Pipe BendingMachine,Welding With Laser Welding Heigh Power Machine.,Bending with fully automaticPipe Bending Machine,Welding With Laser Welding Heigh Power Machine. Wheel Chair Safety Door:CR sheet (1.6-2.0 mm thick)Manufacturing:CNC laser-cut withanti-slip perforated texture Finish:Hot-dip galvanized plus powder coating Load Capacity:Minimum 150 kg per platform.

NS Item -Providing and supplying standard manual wheelchair made of high-quality powder-coated/mild steel tubular frame with durable,corrosion-resistant finish.The wheelchairshall be foldable type for easy storage and portability. Technical Specifications: Frame:Mild Steel/Aluminum,powder-coated finish Seat Width:Approx.18 inches(450 mm),made of durable,washable canvas or PVC upholstery Backrest:Fixed/Foldable with reinforced support Wheels:Rear wheels:24`solid rubber with hand rims for selfpropellingFront wheels:8`PU/solid rubber caster wheelsBrakes:Manual parking brakes on both rear wheels Footrests:Foldable/Detachable,height-adjustable with heel support strapArmrests:Fixed or flip-up cushioned armrestsLoad Capacity:Minimum 100 kg Foldable Design:For convenient storage and transportationWarranty:Minimum I year against manufacturing defect.

NS Item -SIT N NICKER SWING Main Structure Material:Galvanise Steel (GI)ERW Pipes ISI Marked IS1239 Minimum90 mm outer diameter (OD) 2.0-3.0 mm thickness Surface Finish Zinc primer outdoor-grade polyester powder coating(min.60-80 microns),Bending with fully automatic PipeBending Machine,Welding With Laser Welding Heigh Power Machine Bending withfully automatic Pipe Bending Machine Welding With Laser Welding Heigh PowerMachine

NS Item -ARM REVOLVE ASSIST Main Frame:0114*3 mm thick M.S pipe and subordinate tube is of 088*3.0 largethickness M.S pipe. Handle:is made of 088*3 mm thick Pipe and 025 mm round M.S bright bar in bendingdesign. All remaining frame is made by 088*3mm thick MS pipe. Weight plates:Rubberized moulding round weight plates are used. Weight Plates Holder with spring lock and spare weights holder:is made by hard chromeplated mild stee!048 D!A pipe open front covered with half round cap and holder end iscovered with heavy quality rubber ring of OD-68 mm and ID-48 mm with 10mm wallthickness for free weight noiseless operations. Bearing:Lubricated high grade63052RS`steel ball bearing.Base plate:is OD166,ID 116,and 6 mm thick.Pins:are made up of M.S bright bar.Bearing bushes:075mm OD seamless pipe. Weight plate mounting pipe is of 048 mm MS pipe. Seat Frame:made up of hard chrome plated mild steel 48 DIA round pipe. Hardware All hardware`s uses button heads bolts and nuts made up of high tensile steel.Hand grips:Hand grips is used on handles wherever necessary made up of highqualityrubber and handle ends are covered with aluminum/pp/nylon caps with grub screw for longendurance. Closing caps:are of PP/NYLON/HDPE materia!. Laser cutting:profiles of 6mm and 4mm thick M.S sheet are used for connectingsubordinates with each other. Rubber:Safety base pads:Anti-skid safety base pads made up superior rubber to reventslippery and damage to floor.Heavy duty 20mm thick rubber pads are placed for restinghandles for noise less operations. Powders Coating:All components are chemically treated to seal exterior and interiorsurfaces against corrosion.The components are electro statically powder coated atminimum 80-100-micron thickness to make it resistant to scratch,corrosion and humidityin dual color combination. Safety Instructions and Exercise chart on machine -start andfinish position chart stick onA

Percentage BoQ

BoQ_Ver3.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

HSR Item 11.6.1-15 mm cement plaster on the rough side of single or half brick wall of mix : 1. 1:4 (1 cement: 4 fine sand) HSR Rate(Rs.) 138.00 Through Rate

HSR Item 26.122-Providing and displaying of Specimen Croton Petra Bangalore variety plant, having ht. 60 cm to 75 cm with 4 to 6 branches, well developed, fresh and healthy foliage approximately 60-65 leaves in 30 cm size of Earthen pot/Plastic pot and as per direction of the officer-in-charge. HSR Rate(Rs.) 605.00 Through Rate

HSR Item 4.14.1-Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1. All kinds of soil. HSR Rate(Rs.) 83.00 Through Rate

HSR Item 6.1.6-Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 6. 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) HSR Rate(Rs.) 2442.00 Through Rate

HSR Item 13.29.2-Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 2. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works HSR Rate(Rs.) 83.00 Through Rate

HSR Item 4.12.1-Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer in-charge. 1. All kinds of soil HSR Rate(Rs.) 78.00 Through Rate

HSR Item 7.21.1-Brick work with common burnt clay non modular bricks of class designation 10.5 in foundation and plinth in: 1. Cement mortar 1:4 (1 cement : 4 coarse sand) HSR Rate(Rs.) 4128.00 Through Rate

HSR Item 13.19-Providing and fixing galvanised wire mesh of average width of aperture 1.4 mm and nominal dia of wire 0.63 mm fixed on steel windows of standard rolled steel section, with 3 mm thick MS flat iron cover moulding of 12.5 mm width, fixed with machine screws welded complete in all respects. 0 0 0 HSR Rate(Rs.) 649.00 Through Rate

HSR Item 7.22.1-Brick work with common burnt clay non modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : 1. Cement mortar 1:4 (1 cement : 4 coarse sand) HSR Rate(Rs.) 4404.00 Through Rate

HSR Item 10.42-Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. HSR Rate(Rs.) 79.00 Through Rate

HSR Item 6.33.3-Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level Note: Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. 3. Cold twisted bars HSR Rate(Rs.) 68.00 Through Rate

HSR Item 10.100.2-Cement Concrete 1:8:16 Flooring 2. Cement Concrete 1:8:16 with stone aggregate 40 mm size in foundation and plinth. HSR Rate(Rs.) 1863.00 Through Rate

HSR Item 11.71.1-Wall painting on a cement plaster surface with acrylic emulsion paint of approved brand and manufacture to give an even shade : 1. Two or more coats on new work HSR Rate(Rs.) 54.00 Through Rate

HSR Item 8.9.3.2-Stone work (machine cut edges) for wall lining etc. (veneer work) up to 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : 3.2. Gang saw cut stone. 30mm thick Red sand stone HSR Rate(Rs.) 1149.00 Through Rate

HSR Item 26.328-Providing and stacking of Iresine herbstii, of height 20-30 cm. full of branches well developed in 10 cm size of Earthen Pot / Plastic Pot and as per direction of the officer in-charge. HSR Rate(Rs.) 17.00 Through Rate

HSR Item 26.226-Providing and Displaying Petunia hybrid well developed with fresh and healthy foliage in full bloom 15 20 plants in 60x35 cm Earthen Tray and as per direction of the officer-in charge. HSR Rate(Rs.) 30.00 Through Rate

HSR Item 34.8.1-Informatory sign board 800x600 rectangular as per IRC 67- 2012 with retro reflective Sheeting as per ASTM D 4956 09 and as per IRC 67 2012 fixed over 4 mm thick aluminium Composite material (ACM) sheeting having aluminium skin thickness of 0.4 to 0.5 mm on both sided and fixing the same with suitable size aluminium alloy rivets @ 200 mm c/c to back support frame of 25x25x3mm angle iron supported on a square hollow steel section post 60x60x3.2mm conforming to IS 4923 without cost of definition plate firmly fixed to ground in foundation concrete M-25 of size 0.45x0.45x0.75m for vertical post complete as per clause 801 of MORTandH specifications. Supplier shall provide a warranty as per clause 6.9 of IRC 67-2012 for retro reflective sheeting and a certified copy of test reports from an independent test laboratory including three year outdoor weathering test report for sheeting tested in India condition conforming to clause 6.7 of IRC 67-2012 1. Using retro reflective Sheeting Class C as per IRC 67 2012 HSR Rate(Rs.) 4865.00 Through Rate

HSR Item 11.60-Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. HSR Rate(Rs.) 59.00 Through Rate

HSR Item 11.67.1-Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 1. Water thinnable cement primer HSR Rate(Rs.) 22.00 Through Rate

HSR Item 26.215-Providing and Displaying Marigold(Tagetes) inca hybrid different colour having 30 cm and above ht., with 6 to 8 flowers in bloom and blooming condition, well developed pot should be fully covered with fresh and healthy, foliage and flowers in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. HSR Rate(Rs.) 72.00 Through Rate