Development of sport facilities in school under smart city mission

Amount

Civil Works PROVIDING & LAYING OF 15 MM (9 MM SBR BOTTOM LAYER + 6 MM EPDM TOP LAYER) COLORPLAY EPDM GRANULES MATERIAL REQUIRED PARAMETERS : EPDM GRANULES OF MAKE BSG, NOVAL, COLORPLAY MANUFACTURED UNDER QUALITY MANAGEMENT SYSTEM OF ISO 9001.2015 OR ABOVE HAVING POLYMER CONTENT 20-22 %.MINIMUM MATERIAL REQUIREMENT – A. EPDM GRANULES TEST REPORTS: 20 - 22% POLYMER CONTENT. B. HIGH UV RATING: MIN 4/5 ON GREYSCALE. C. VOC less THAN 3.0 g/l D. COMBUSTABILITY LESS THAN 40 mm/min TEST METHOD UL-94HB E. ELONGATION AT BREAK IS MORE THAN 500% F. EPDM ORIGIN : EUROPEAN / USA / JAPAN G. DECLARATION-REACH/SVHC & ROHS COMPLAINT. ANTIMICROBIAL & ANTIFUNGAL TESTTED. THE RESTICTION OF HAZARDOUS SUSTANCES (RoHS) DIRECTIVE 2002/95/EC & WEEE DIRECTIVE 2002/96/EC H. MATERIAL : STANDARD GRAIN SIZE 1.00 – 3.50 MM TECHINCAL REPORTS WILL BE PROVIDED INSTALLATION PROCESS - RUBBER FLOORING SANDWICH SYSTEM WITH APPLICATION ON CONCRETE- MICRO CANAL DRAINAGE SYSTEM/SKIRTING- APPLICATION TO BE DONE WITHOUT ANY EXTRA CHARGES. LAYER 1 – POLYURETHANE BASED PRIMER COATING. LAYER 2 –9 MM BLACK RUBBER BASE PARTICLE/ LONG RUBBER STRANDS / SBR RUBBER CRUMB MIX WITH SINGLE COMPETENT PU BASE BINDER( 12-14%). STYRENE BUTADIENE RUBBER/ SYNTHETIC RUBBER. LAYER 3 – 6 MM EPDM GRANULES CHEMICALLY BONDED WITH MDI (18-20%) WITH SINGLE COMPONENT OF DIPHENYLMETHANE DIISOCYANATE AND PARAFFINIC OIL ETC. DESIGN ON BASE & TOP LAYER BY SPECIALIZED TEAM OF INSTALLERS ACCORDING TO THE SPECIFICATION OF APPROVED MATERIAL AND SHADE AS PER THE DIRECTION OF ENGINEER IN CHARGE.

Providing and fixing Basket ball pole of INTERNATIONAL STANDARD BOARD SIZE: 180CM X 105CM, 20MM WITH SAFETY CRASH PADDING WEATHER PROOF NON SCRACHABLE TRANSPARENT ACRYLIC BOARD ON INTERNATIONAL STANDARD WHICH IS IMPORTED FROM TAIWAN, POLE EXTENTION 2.20 MTR, MADE OFHEAVY(14GUAGE) 6 INCH SQUAREPIPE WITH HEAVY 6MM 3 SPRING DUNKING RING & NYLON NET, BEST QUALITY SPRAY PU WOOD COATPAINT. POLE FRONT SAFETY CRASH PADDING. AS INSTRUCTED BY ENGINEER-IN-CHARGE.

Providing and fixing 100 LPH Water Cooler with inbuilt RO System (60 ltr PH),Structure NSF Approved Frame SS 304 steel,Pre Filter (Ist stage):-10 Micron Sediment—20",Carbon Filter-IIIRD stage:-GAC NSF with 20” Housing Kemflo(USA)1100 id value,Booster Pump IV th stage :-1.8 LPM1 No—Kemflo (USA) 48 volt,Transformer:-48 Volt 2 No—Delta with 36v additional output,Production Rate 60 LPH,Membrane (Vth Stage)1 No TFC 200 GPD Inline Post carbon 10 “ (VI th stage):-2 % Silver Impregnated Carbon(Kemflo / shurflo) - USA,Anti Scalant Dosing (VII th stage):-Balls with Sediment Filter USA Autom,ation Circuit CCK,Tubing:-Imported cck /Kemflo,Low Pressure Switch:-cck (USA),Float with micro switch:-cck (USA),Inlet Water assembly:-3 way with flow control,Fittings & Pipes :-All Push Fit with NRV facility,Solenoid Valve:-24 /36 Volt,Inlet Pressure Range 5/2.5 kg/cm2,Rejection of TDS 90 /95 %,Recovery 25/40 %,Operating Voltage 230 V AC.

Electrical works Control Panels for Main building Lighting : Fabrication, supplying and installation of outdoor type cubical panel board of suitable size made out of GI sheet 2 mm thick (14 SWG) and powder coated thereafter, duly compartmentalised having door locking arrangement for protection from rain, dust, duly fixed on GI angle iron frame work of size 50 mm x 50 mm x 6 mm (NS) and having following accessories mounted inside the panel including connection, inter connection with aluminium thimbles, earthing with two nos. earth studs, duly powder coated complete etc. as required,Civil Foundation cost for the panel shall be inclusive. Cable gland plates shall be provided on bottom. 2 Nos. earthing terminals shall be provided. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels. Incomer : 125 A TPN MCB - 1NOS Outgoing : 32A TPN MCB - 6 NOS Indication lamps (RYB) with control MCB - 03 Sets with timer and contactor Danger notice plate Make : As listed in UHBVNL

Supply , Installation, Testing and Commissioning of 400W flood flight pressure die‐cast aluminium LED housing designed to act as heat sink for efficient dissipation of heat, Electrochemically brightened and anodized aluminium reflector, Heat resistant toughened glass provided with gasket and SS clips. LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level)>=120lumens/watt, Minimum system Lumens 6,000 lm. Life of fixture 50000hrs@L70% Lumen maintenance, CCT up to 5700K ±300K, CRI >70, PF >0.95, THD<10%, Operating Temperature Range-5 deg C to +50deg C, IP66 & Impact resistance of IK07. Built in Surge Protection of 4KV and an operating Voltage Range of 140 to 277V AC,50Hz. The driver should be specially designed to have built‐in surge voltage, open/short circuit protections. Luminaire is provided with a MS mounting bracket fixed on pressure die‐cast aluminium housing for aiming adjustment. The fixture should comply with the parameters as per IS10322 and IEC60598, EMC / EMI compliance. LED Makes should be CREE / Lumileds / OSRAM/ Seoul/ Philips Fixture Make: Bajaj/Philips/Cromptom/Osram/VAK

Supply of following size XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) 4C x 10 sqmm Al Ar cable

Supply of following size XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) 4C x 16 sqmm Al Ar cable

Supply of following size XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) 4C x 25 sqmm Al Ar cable

Supply of following size XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) 3.5C x 50 sqmm Al Ar cable

Supply of following size XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) 3.5Cx2.5sqmm Cu flexible cable

Parking, Volley ball & Basket ball courts Supply and Installation of 90W Street light luminaire to be mounted on 8Mtr columns, LED luminaire having Epoxy powder coated pressure die‐cast aluminium housing,Weatherproof gaskets should be provided for LEDs and control gear compartments.Luinaire should be suitable for Side entry mounting for max. 38mm OD pipe bracket.The LED driver acces should be from top for easy maintenance.LEDs should be provided with non‐yellowing modular secondary lens optics.LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level)>=120lumens/watt, Minimum system Lumens 5400 lm ±10%. Life of fixture 50000hrs@L70% Lumen maintenance, CCT up to 5665K ±355K, CRI>=70, PF>=0.9, THD<10%, and Operating Temperature Range-5 deg C to +45deg C, IP66. Built in Surge Protection of 4KV & external surge protection of 10kVand an operating Voltage Range of 140 to 270V AC,50Hz.Luminaire Weight should not exceed 1.5kg.The driver used is specially designed to have built‐in surge voltage, open/short circuit protections.The fixture should comply with the parameters as per IS10322 and IEC60598, EMC / EMI compliance. LUMINAIRE MAKE : Phillips / Bajaj / VAK /Keselec. LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM.

Bidder Name

Amount

M/S Singla Construction Co.(GSTN-06BDPPS4086R1ZE)

Ved Parkash Contractor(GSTN-NA)

Ved Parkash Contractor

Ved Parkash Contractor