PROVIDING AMENITIES AND FACILITIES TO DEVOTEES, UNDER MASTER PLAN PHASE II

Amount

Dismantling, clearing away and carefully stacking materials of brick masonry walls in cement mortar works as per standard specification and as directed by the Departmental Officers.

Foot Hill

Dismantling, clearing away of Plain cement concrete in floors works as per standard specification and as directed by the Departmental Officers.

Foot Hill

Dismantling, clearing away and carefully stacking materials ofAc sheet roof without roof timbers works as per standard specification and as directed by the Departmental Officers

Foot Hill

Dismantling, clearing away and carefully stacking materials for Petty iron work for truss, straps etc., clearing away the old materials as directed by the Departmental Officers.

Foot Hill

Dismantling, clearing away and carefully stacking materials for RCC by manual / by using deploying machineries clearing away the old materials as directed by the Departmental Officers.

Removal of existing cut stone slabs in the steps as directed by the departmental officers.

NEW BUILDING CONSTRUCTION

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Foot Hill (95+140+45)

Earth work excavation for foundation (for narrow excavation) in Medium rock and Dense medium rock area to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts.in medium rock and dense medicum rock not requiring blasting and clearing and levelling the site, etc., complete complying with standard specification.

Foot Hill (36+165+50)

Cement Concrete 1:5:10 (One Cement, Five sand and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification

Foot Hill (8+25+55+20)

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid) ( For Plinth and Foundation )

Foot Hill (41+100+300+65)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

Plane surfaces such as RCC floor slab, roof slab, rectangular, square Tee or Ell beam, lintel, bed block, staircase waist slab, landing slab, landing beam, portico beam, portico beam, portico slab etc.,

Foot Hill ( 81+238+1165+175)

Plane surface such as RCC square or rectangular column, top and bottom slab of sunshade, boxing, sill slab etc.,

Foot Hill (58+132+660+100)

Centering for curved surfaces of all RCC items of work

Foot Hill (53+80+265)

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Foot Hill (53+80+265)

Providing and laying in position, Standaardised Concrete Mix M-20 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser/super plasticiser) in recommended proportions ad per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with abour (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing etc. and providing fixtures like fan clamps in the RCC floor/roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

For Foundation and Basement

Foot Hill (11+25+95+30)

For Superstructure in Ground floor upto 4.5 m

Foot Hill (24+47+125+30)

For Superstructure in Ground floor above 4.5 m

Foot Hill (1+125)

For Superstructure in Second floor

Foot Hill

Supplying and FILLING GRAVEL Supplying and filling in 'foundation and basement with filling crushed stone sand in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete

Foot Hill( 1+15+215+10)

Supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Foot Hill (1+15+46+10)

Supplying and filling basement witth conveyed earth from 10 km as directed

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification.

Foot Hill (3+20+46+25)

Supplying, fabricating and placing in position of Steel reinforcement using MS (or) RTS rods for all RCC item of works including cost of steel and binding wire in all floors etc., complete complying with standard specification and as directed by the departmental officers.

Foot Hill (40.5+77.87+395+61)

Brick work in following Cement Mortar 1:5 using fly ash bricks of size 230 x 110 x 75 mm for foundation and basement including curing, etc., complete complying with standard specification.

foundation

Foot Hill(3+11+68+25)

Brick work in following Cement Mortar 1:6 using fly ash bricks of size 230 x 110 x 75 mm for foundation and basement including curing, etc., complete complying with standard specification.

For Superstructure in Ground floor

Foot Hill (5+36+87+22)

For Superstructure in First floor

Foot Hill

For Superstructure in Second floor

Foot Hill

Brick partition walls of 11.50cm thickness in Cement Mortar 1:3 using Fly ash Bricks 230 x 110 x 70mm including cost and conveyance of all materials and labour charges and all other incidental charges etc completc complying with standard specification.

For Superstructure in Ground floor

Foot Hill(25+40)

For Superstructure in First floor

Foot Hill

Supplying and fixing jet black granite slabs of 0.61*1.22m.,18/20mm thick in all floors for urinal partition including for labour charges for fixing and polishing etc.,

Foot Hill

Plastering with cement mortar 1:5 (one cement and five sand) 12mm thick in all floors using fine river sand including neat finishing, curing, etc., complete complying with standard specification and as directed by the department officers.

Foot Hill (60+500+3355+480)

Special ceiling plastering and finishing the exposed surface of RCC items of work such as slab, beam, sunshade, facia, canopy slab, staircase waist slab, landing slab etc., with cement mortar 1:3 (One cement and three sand) 10mm thick including hacking the surfaces and providing cement mortar nosing, beading for sunshade, staircase, step, landing slab etc., including neat finishing and curing etc., complete complying with standard specification and as directed by the departmental officers.

Foot Hill (195+320+1440+200)

Painting the exterior wall surface two coats with best and approved first quality and colour of Water based Emulsion Paint in all floors over one coat of primer including preparation of surface, wall putty two coats with good quality of wall putty including cost of wall putty, emmary sheet, plates etc., and including labour charges for rubbing the wall scrapping putty pasting works and making good smooth surface and finishing neatly etc., The cost inclusive of preparation of surface, cost of all materials, brushes, scaffolding charges etc., complete complying with standard specification and as directed by the departmental officers.etc., (The make, quality and colour of paint should be got approved by the Executive Engineer before use on work).

Foot Hill (320+830+4600+520)

Paving the floor with best approved quality Flamed steel grey Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Foot Hill(46+150+254)

Laying seaters with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Providing Single Nosing for Granite Slab etc., complete complying with standard specification and as directed by the departmental officers etc., complete.

Foot Hill (10+150)

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Foot Hill

Paving the floor with best quality Double Charged Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Foot Hill

Flooring with following Joint free Rectified Glazed Ceramic Flooring tiles 305 x 305 x 8mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Foot Hill(40+100)

Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. Size 450x300x8mm.

Foot Hill(209+165)

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Foot Hill (5.5+13.5+36+10)

Finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Foot Hill (45+125+345+100)

Supplying and fixing mild steel grills for windows, ventilators, rtc., including priming coat as per standard specifications.(ornamental)

Foot Hill (2030+2520)

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work. Sliding Window

Foot Hill (5+75)

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Foot Hill (25+10+12)

Supplying and fixing Teakwood frame with scantling above 2m for doors including labour charges for wrought and putup in possible and for fixing holdfast in frame and necessary etc., complete.

Foot Hill (0.50+1)

Supplying and fixing Teakwood fully panelled shutters for using Teakwood scantlings upto 4m length and teakwood 40mm thick for styles and rails and 22mm thick for planks and panels including cost of wind appliances and labour charges for fixing the furniture fittings in position but excluding cost of furniture fittings complete as directed by the Departmental officers.

Foot Hill

Supplying and fixing SolidCore Flush Shutters with teakply on both side with teakwook lipping alround 35mm thick including cost of wind appliances and labour charges for fixing the furniture fittings in position but including cost of furniture fittings complete as directed by the Departmental officers.

Foot Hill

Supplying and fixing of FRP Door Sutter with FRP Door Frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of holdfasts and Solid Core FRP Shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by Engineers

Foot Hill(12+13)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of zinc chromite priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Foot Hill(70+175+20)

Polishing the teak wood door with both side Melamine polish with approved quality and brand over a coat of bee's waxing including preparing the wooden surface to receive polishing, etc., complete complying as per the standard specifications. (The make, quality and colour of french polish, bees vax should be got approved by the Executive Engineer before use on works.)

Foot Hill (35+55)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Foot Hill (25+20+48+4.5)

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for queue using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Foot Hill (30+28+15+15)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Foot Hill (5+5.5)

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Foot Hill (15+3)

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Foot Hill(16+12)

Supplying and fixing in position best quality Indian made white glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2nos. and fixing the urinals in position with necessary TW plugs, clamps, screws, etc, including dismantling masonry and re-doing the same to the original condition, etc, including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage, etc, complete complying with standard specifications and as directed by the departmental officers, (The urinal should be got approved by the executive engineer before use on works)

Foot Hill(15+3)

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Foot Hill(2+10)

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

40mm dia-Foot Hill

32mm dia-Foot Hill

15mm dia-Foot Hill

Supply and fixing PVC water tank etc complete with standard specification

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

PVC Pipe 110 mm dia -Foot hill

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. Abow ground level

PVC Pipe 32 mm dia -Foot Hill

PVC Pipe 15mm dia -Foot Hill

PVC Pipe40 mm dia -Foot Hill

Supplying PVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements

32mm PVC Coupling

32mm PVC elbow

32mm PVC tee

32mm PVC bend

15mm PVC coupling

15mm PVC elbow

15mm PVC tee

15mm bend

40mm PVC coupling

40mm PVC elbow

40mm PVC tee

20x15 PVC reducer

20x15 PVC reducer tee

32x25 PVC reducer tee

40x32 PVC reducer tee

Supplying and fixing of Brass Chromium Plated Screw Down 15 / 12mm dia of approved make conforming to I.S.specifications and quality including cost of shellac , thread etc.complying with standard specifications and including cutting and threading wherever necessary (Taps should be got approved by the executive Engineer before use on the work.

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Foot Hill (15+13)

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Foot Hill(16+12)

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Foot Hill

Damp proof Course with Cement Mortar 1:4 (One cement & four sand) 12mm thick of the following mixed with water proofing compound of approved quality confirming to ISS @ 2% by weight of cement used as complete complying with standard specification and as directed by the department officers.

Foot Hill (66+35)

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.

Foot Hill (50+134.52+360+105)

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

110mm PVC bend - Foot hill

110mm PVC elbow - Foot hill

110mm PVC tee - Foot hill

110mm PVC Door tee - Foot hill

Supplying and erecting pull and push type rolling shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc.,

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4kg/sq.cm) with 3 meter height including cost of PVC cylindrical cowl of best approved qulaity etc. complete complying with standard specifications and as directed by the departmental officers.

Brick masonry Lime Mortor1:2 using Stock bricks including all varivargams, moulds, sthambams, mukapathrams, koodu, nasi and all ornamental brick work complete, all pancharams, agarais, karnakoodus, etc., forming core walls of Rajagopuram/ Vimanams complete including cost and conveyance of all materials including cement, all the labour charges including marking pathies shaping of the bricks, lifting of all the materials to required heights, curing and all extra for working in heights etc., complete 100 cft for vimanam / gopuram

Foot Hill

Providing Vargapoochu over the corewalls of Vimanams / Gopurams, with Lime Mortar1:1.5 complete including shaping the mukhapathram, mahanasi, Koodu all ornamentals works to proper shape by embedding broken bricks of shaped/chiseled bricks, rough-plastering with Cement Mortar1:4and finishing with final ornamental plastering and nayam theervani including cost and conveyance of all materials, labour therefore, lifting of materials, all working in heights, curing with water etc, complete including all extra for folding and including clearing from the vimanams/gopurams 100sft superficial area. for kalkaram

Foot Hill

Painting with multicolour (Panchavarnam) good water based exterior emulson paints complete for the Vinamans/Gopurams, including cost and conveyance of all materials, lobour charges including Artist painter, working in heights, lifting of material, cost of brushes etc, complete-which including all extra for foldings-100sft, superficial area.

Supplying and fixing in position of Indian make Water closet Oriyya Type of size 580mm x 440mm of approved uality with 'P' or 'S' trap including cost and conveyance of all materials and labour charges for fixing in position,etc., complete.

Foot Hill

Fixing and dressing the old cut stone flooring for single line dressed on all face set and pointing with lime mortar 1:1.5 including handling charges cost of tools and fixing in position etc., complete

Supplying, Fixing and dressing the new cut stone flooring for single line dressed on all face set and pointing with lime mortar 1:1.5 including handling charges cost of tools and fixing in position etc., complete

Random rubble masonry in CM 1:5 using hard broken rough stones and bond stones in each layers with simultaneous pointing including cost and conveyance of all materials and labour charges

ELECTRICAL WORKS

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End (Data A)

Foot Hill (19+32+154+21)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (4 points / Coil) Higher End.) (Data B)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End.) (Data B)

Foot Hill(34+8)

Supply and fixing of 4' 20W LED fitting with LED tube on wall or ceiling or existing duct with TW round blocks with copper leads from fittings to Terminals (Data C)

Foot Hill (4+95+14)

Supply and fixing of 24W LED 2x2 square type fitting with LED (Higher end) on Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting (SD 526)

Foot Hill

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18") (SD 549)

Foot Hill (5+14)

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600mm down rod on existing fan clamp (SD 585)

Foot hill

Supply and fixing of 40W lowbay light on ceiling with necessary MS clamps and electrical connections complete. (Data C)

Foot Hill

Supply and fixing of 150W LED highbay light fitting complete with necessary MS clamps on ceiling and electrical connections complete.(Higher end) (Datat B)

Supply and fixing of warm white 18W LED square type fitting with LED (Higher end) on ceiling with suitable support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (SD 528)

Supply and fixing of 7W/9W LED for BH point (Data D)

Foot Hill

Supply and fixing of 300mm (12") sweep AC exhaust fan complete with necessary wall opening and making good of the wall (SD 114)

Foot Hill

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan (SD 120)

Foot Hill

Supply and fixing of 375mm (15") sweep heavy duty AC exhaust fan complete with provision(DATA F)

Foot hill

Supply and fixing of louvers shutters arrangements for 375mm (15") sweep (light duty) AC exhaust fan (SD 121)

Foot hill

Supply and fixing of 1 no. 20A 2M Key fab on suitable module concealed Box (GI) in flush with wall with connections. Higher End (Data D)

Foot Hill

Supply and fixing of 2 nos.6A two module 5 pin socket , 2 nos. 6A one module switch on suitable module surface mounting Box (Plastic) with module cover plate (plastic) on wall with connections. Higher End (Set plug) (SD 466)

Foot hill

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (Set plug) (SD 476)

Foot Hill

Supply and fixing of 1no.6A two module socket , 1 no. 6/16A two module socket, 1 no. 6A one module switch, 1 no.16A one module switch on suitable module surface mounting box (plastic) with module cover plate (plastic) on wall with connections. Higher End (SD508)

Supply and fixing of 1no.6A two module socket , 1 no. 6/16A two module socket, 1 no. 6A one module switch, 1 no.16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End (SD 512)

Foot Hill

Supply and fixing of 1 no. 6/16A two module socket, 1 no.16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End (SD 488)

Foot Hill

Supply and run of 2 of 2.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 2.5 sqmm. copper wire and making good of the concealed portion with suitable colour (SD 428)

Foot Hill(15+80+700)

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 2.5 sqmm. Coper wire with painting of suitable colour. (SD 427)

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 2.5sqmm. copper wire and making good of the concealed portion with suitable colour (SD 430)

Foot Hill

Supply and Run of 4 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 2.5 sqmm. Coper wire with painting of suitable colour. (SD 437)

Supply and run of 4 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 2.5sqmm. copper wire and making good of the concealed portion with suitable colour (SD442)

Foot Hill

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting (SD 535)

Foot Hill

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 613)

Foot Hill

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 601)

Foot Hill

Supply and fixing of 4 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 2 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (Data B)

Foot Hill

Supply and fixing of 6 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100A 4P isolator as incoming and 6 nos. 32A TP MCB as outgoing in flush with wall with earth connection only. Higher End (Data E)

Foot Hill

Supply and fixing of DP sheet enclosure with 40A30 mA DP RCCB in flush with wall with earth connection (Data F)

Foot Hill

Supply and Laying of 3½ x 70 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (SD 749)

Foot Hill

Supply and clamping of 3½ x 70 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 225)

Foot Hill

Supply and fixing of brass cable gland for 3½ x 70 sqmm PVC armoured LTUG cable with earth connection. (SD 189)

Foot Hill

Supply and Laying of 2 x 10 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (Data C)

Foot Hill

Supply and clamping of 2 x 10 sq.mm PVC LTUG armoured Alu cable in on post or on wall with MS Clamps. (SD 216)

Foot Hill

Supply and fixing of brass cable gland for 2 x 10 sqmm PVC armoured LTUG cable with earth connection. (SD 182)

Foot Hill

Supply and providing cable end termination of 3½ x 70 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 238)

Foot Hill

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) (SD 140)

Foot Hill

Supply and fixing of 1.5 TR Split AC with 4 KVA stabilizer with copper coils 3 star rated of reputed make with MS stand, PVC drain pipe and accessories and as directed by the departmental officers. (Data G)

Foot Hill

Supply and fixing of 1500W automatic electric water heater of 35 litres capacity suitable for 230V 50 c/s AC supply on suitable MS clamps with 3 core flex wire but without plumbing connection (SD 104)

Foot Hill

Supply, Erection, testing and commissioning of 125 A capacity dust and vermin proof horizontal type cubical panel board made up of 16 SWG CRCA Sheet with supply and fixing of the following interior switches with HRC fuse links arranged horizontally with horizontal busbar chamber and cable chambers. 1. 125A FP Changeover switch interior only -1 No. 2. 32A TPN switch disconnector fuse unit interior only with HRC fuses double break-1 No. 3. 63A TPN switch disconnector fuse unit interior only with HRC fuses double break-4 Nos. The busbar chamber shall consist of 4 Nos 25mm x 6mm copper flat for phases and neutral and interconnection between incoming switch and buses. The no.8 copper for interconnection between 63A TPN switches and 32A TPN switch to buses. 25mm x 6mm copper flat buses shall be mounted on SMC busbar insulator at proper and sufficient interval as per IE rules. The busbar chamber shall be segregated from the adjacent chamber. The heat shrinkable sleeves shall be provided for busbar with colour code. The 25mm x 3mm copper flat for double earth connection for all incoming and outgoing switches are to be provided in this panel. The panel shall have powder coated painting of approved colours, approved by the department officers. The danger board shall be fixed at front of panel board. The panel shall be mounted on MS base channel provided all round at the bottom of the panel. The whole arrangements shall be erected on a Masonary pedestal to be constructed with suitable foundation with bolts and nuts such that the lowest SDF unit fuse handle is at a height of 0.75m from the ground level. (note: All SDF unit shall be of L&T / Siemens make). (Data H)

Foot Hill

Supply, Erection, testing and commissioning of 125 A capacity dust and vermin proof horizontal type Metering cubical panel made up of 16 SWG CRCA Sheet with supply and fixing of the following 4Pole and 2pole ELCB / RCCB with horizontal busbar chamber, cable chambers and provisions for fixing TNEB Meters. 1. 125A 4 P ELCB / RCCB -1 No. 2. 40A DP ELCB / RCCB - 10 Nos. 3. Meter view glass - 10 Nos The busbar chamber shall consist of 4 Nos 25mm x 3mm copper flat for three phases and neutral. The 10sqmm copper wire for interconnection between buese to 1 No 3 phase meter and 10 nos single phase meters to 4P and DP ELCBs respectively. The copper flat buses shall be mounted on SMC busbar insulator at proper and sufficient interval as per IE rules. The busbar chamber shall be segregated from the adjacent chamber. The heat shrinkable sleeves shall be provided for busbar with colour code. The 25mm x 3mm copper flat for earth bus shall be provided all round the panel and 10 sqmm copper wire for Double earth connection for all outgoing meters. The panel shall have powder coated painting of approved colours. The danger board shall be fixed at front of panel board. The panel shall be mounted on MS base channel provided all round at the bottom of the panel. The whole arrangements shall be erected on a masonary pedestal to be constructed with suitable foundation. The lowest metering chamber shall be a height of 0.75m from the ground level. (note: ELCBs / RCCBs shall be of L&T / Siemens make). (Data I)

Foot Hill

Supply and fixing of 125A (500V) changeover switch with with cable entry boxes on wall with electrical connections complete. (Data J)

Foot Hill

Design, Supply, erection, Testing, Commissioning and handing over of High Mast Structure (Bajaj / Philips / Crompton make or equivalent) with required number of continuously tapered hot dip galvansied steel polygonal side sections with telescopic strip joints to a total of 16 meters capable of sustaining the maximum wind pressure at the erection site with single flange base mast section with vertically moveable hot dip galvanised lantern carriage and accessories such as electrical junction box brackets for providing 8 Nos of 150W LED flood light luminaries with control gear box complete head frame assembly, pulley drive stainless steel wire rope single / double drum self-lubricating winch arrangements suitable for raising and lowering the luminaries carraige ring flexible multi core power cable and necessary high tensile hot dipped galvanized foundation, bolt & nuts along with washers and templates including supply and fixing the following accessories in the Mast design and casting of suitable foundation with 1:2:4 mix RCC concreate with 30cm projection above the ground level with 1 mtr width x 1mtr length x 2 mtrs depth with necessary galvanised foundation bolts nuts and washers and dump plates enclosing the bolts nuts for high mast cosidering the safe soil bearing capacity at site-1 Set b) High powered power tool with complete with hand held control panel and motor with push button type remote control switch suitable for 3 phase 415 V /50 HZ for raising and lowering of the lantern carriage complete to operate all fittings mounted in the base to couple with winch-1 SET c) Feeder pillar box comprising of 0.90m x 0.45m x1.20m floor angle iron frame with 63 A power contactor starter for the 3 Phase motor- 1Set d) Neon aviation obstruction light (Bajaj/equivalent) - 1No. e)2Nos of special GI earth electode with copper plate 300 x300x3mm

Foot Hill

Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (SD 745)

Foot Hill

Supply and clamping of 4 x 16 sq.mm PVC LTUG armoured Alu cable in on post or on wall with MS Clamps. (SD 221)

Foot Hill

Supply and fixing of brass cable gland for 4 x 16 / 4 x 25 sqmm PVC armoured LTUG cable with earth connection. (SD 185)

Foot Hill

Supply, erection, commissioning and testing of 30 KVA Diesel generator with acoustic arrangements in accordance with CPCB norms, water / coolant oil cooled type engine with 38.5 BHP for 30 KVA generator at 1500 rpm under NTP conditions with following specifications. The engine should have turbo charged, should be provided with air cleaner, base frame, crank case, lubricating oil, fan and fan drive, fuel and oil filters, flexible fittings, exhaust governor, hydro-mechanical gauges for fuel pressure and oil pressure, tachometer, digital water temperature gauge, charging arms, muffler, exhaust pump for fuel priming, fuel transfer, jacket with radiator engine oil, safety set ups with engine shutdown system for LLOP including the set of tools, spares as supplied by the manufacturer along with the Engine. The alternator should have brushless self-excited Y connected, self- regulated of continuous rating, developing an output of 24KW at 0.8 power factor lagging, 415 V, 3 phase, 50 Hz at 1500 rpm with a voltage regulation of ±1 % under steady state condition with over speed capacity of 10% for 5 minutes withstanding capacity with class H insulation, ingression protection of IP23 with topicalization. The alternator is to be designed, built & tested to IS, BS, IEC or any other equivalent Indian or International Standards.\ The engine should be provided with suitable electrical starting system including, suitable radiator arrangements with suitable fully charged new batteries and with other connecting accessories. microprocessor based genset controllers display and displayed at phase voltage & currents, Frequency, reverse Power, Genset KVA, KW, KWh, KVAr, power factor, canopy temperature, lube oil pressure, engine temperature, RPM, run hours, number of starts, fuel level, auto / manual stop, battery charge condition. The fuel tank should be fabricated with 14 SWG CRCA MS sheet steel inbuilt removable type sheet metal fuel tank with fuel gauge drain plug and fuel connections, fuel level indicator and with a capacity of not less than 75 Ltrs. Provisions are to be made to filter the sediments, water in the fuel at rear side and provision of vent at top to release the air pressure in the tank. The tank should be painted with noncorrosive and non-flammable paint. The fuel tank should be filled with a minimum level of fuel for test running on full load. (Make: Cummins/ Kriloskar / eql) (Data K)

Foot Hill

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection (SD 76)

Foot Hill

Earthing as per PWD standard with an earth electrode of 2 metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work (SD 233)

Foot Hill

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD 233)

Foot Hill

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection (SD 458)

Foot Hill

Supply and fixing of busbar box chamber with IP 65 protection with 32A 3 phase and neutral in suitable sheet steel metal enclosure and 1 no. 32A FP MCB in separate sheet steel enclosure on wall with necessary accessories and electrical connections complete. (Make: Legrand / Eql). (Data C)

Supplying and fixing of 4 nos 6-32A SP MCB in Double door set enclosure with IP 42 protection on wall with earth connection. (DATA D

Supply and fixing of TNEB meter board suitable for 32A three phase service connection with 3 Nos. 32A fuse unit (500V) 32A neutral link and earth link (1" x 1/8" copper flat) on TW plank of size 600mm x 450mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit (SD 127)

Supply and fixing of 50A 400V, 50 Hz 3 phase 4 wire watt hour meter on suitable TW box with earth connection (SUB METER FOR PROPOSED MANDAPAM)(SOR-M1544)

GST 18 % in Figures

K CHINNU & COMPANY CONSTRUCTIONS PRIVATE LIMITED (BID ID -1359684)

Selvam Infrastructures (BID ID -1359676)